CERTAIN SANCTIONED WORKS OF KV CHHATRAPATI SAMBHAJINAGAR CANTT UNDER GE(S) AHMEDNAGAR

Amount

M&L for Surface excavation n. exc 30 Cm deep and averaging 15 cm deep and getting out in Soft/loose soil.

Earth work in Excavation by Mechanical means (Hydraulic excavator) over areas not exceeding 1.5m depth for foundation in any type of soil and getting out and disposal of excavated earth lead upto 50m and lift upto 1.5m complete all as specified and directed.

Earth work in Excavation by Mechanical means (Hydraulic excavator) over areas exceeding 1.5m but not execeeding 3m in depth for foundation in any type of soil and getting out and disposal of excavated earth lead upto 50m and lift upto 1.5m complete all as specified and directed.

Excavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation, pipe line or for manholes not exc 10 Sqm on plan and not exc 1.5m in depth in any type of soil and getting out all as specified and as directed.

Returning, filling in (soil) including spreading, levelling, watering and well ramming in layers not exc 25cm thick all as specified and all as directed.

Removal of excavated material (soil) to a distance not exc 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and as directed.

M&L for plain cement concrete, 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for RCC, M-25 (design mix) using 20mm graded crushed stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases of columns etc. complete all as specified and as directed.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams; and similar work; vertical or to batter for rough finished surfaces of concrete complete all as specified and as directed.

M&L for RCC, M-25 (design mix) using 20mm graded crushed stone aggregate as in columns, pillars, piers, posts and struts etc. complete all as specified and as directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns etc. for rough finished surfaces of concrete complete all as specified and as directed.

M&L for RCC M-25 (design mix) using 20mm graded crushed stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span etc. complete all as specified and as directed.

Use and waste of formwork to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves including supports, etc for rough finished surfaces of concrete complete all as specified and as directed.

M&L for RCC M-25 (design mix) using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), etc for rough finished surfaces of concrete complete all as specified and as directed.

M&L for RCC M-25 (design mix) using 20mm graded crushed stone aggregate as in fins, fascias, louvers, parapets, and railings exc 60cm in height, newels, balustrade, etc complete all as specified and as directed.

Use and waste of formwork to faces of wall, retaining walls, abutments, parapets and staircase railings and similar work including attached pilasters, buttresses, etc for rough finished surfaces of concrete complete all as specified and as directed.

M&L for mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified and as directed.

M&L for mild steel TMT bars, 6mm to 8mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified and as directed.

M&L for mild steel TMT bars, 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified and as directed.

M/L for Damp proof course to horizontal or vertical surface including necessary formwork of 40 mm thick in PCC (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregate mixed with integral water proofing compound conforming to IS-2645 complete all as specified and as directed.

M & L anti termite Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface complete all as specified and as directed.

M & L anti termite Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed.

M & L anti termite Treating the the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M & L anti termite Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and as directed.

M&L for providing cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses lacing courses, parapets and railings coping, kneelers, apex stones, bed plates, water throughs and the like including weathering, slightly rounded or chemfered angles and throating complete all as specified and as directed .

M&L for PCC 1:3:6, type C-1 (using 20mm graded stone aggregates) as in hold fasts, bed blocks, bed plates, concrete filling around pipes including necessary formwork all as specified and as directed.

M&L for brick work with old size fly ash ‘B’ bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified.

M&L for Brickwork with old size fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4, duly mixed with WPC as per manufacturers instructions, finished even and fair complete all as specified and as directed.

M&L for rendering 10 mm thick on fair face of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5 mm thick on fair faces of concrete surfaces as in soffits of slab in cement mortar 1:3, finished even and smooth without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified.

M&L for framed work such as grills grating etc with end of bars shoulderd and/or riveted .welded or forged into spikes.framedguard bars iron doors.ladders framed balusters , walk ways. railings, frame work of water tanks and similar work conforming to Fe 290 Gde E-165 all as specified and as directed.

S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per specifications & drawing complete all as specified and as directed by Engineer-in-Charge

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per specifications & drawing complete all as specified and as directed by Engineer-in-Charge

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: Stainless steel butt hinges shall be paid separately under respective item.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of 30 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Note: Stainless steel butt hinges shall be paid separately under respective item.

S&F Aluminium handle, cast type anodised, 150 mm size complete all as specified and as directed.

S&F Aluminium anodised tower bolt of extruded section of 200 mm size, complete all as specified and as directed.

S&F 300 mm long aluminium anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and as directed.

S&F butt hinges,Stainless steel, 100mm long fixed with welding to existing MS pressed steel chowkhat/shutter or fixed to wooden/WPC frame with necessary SS screws complete all as specified and as directed.

S&F continuous (piano) hinges, mild steel bright finish or electro-galvanised, 30mm width of flaps (when open) all as specified and as directed.

Filling under floors including spreading, levelling, ramming and watering in layers not exc.25 cm thick complete all as specified and as directed.

M&L for moorum filling in floors or paving, laid in layers not exc 15cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for hard core of broken stone/boulders of gauge not exc 63mm deposited spreed and levelled in layers not exc 15cm thick, watered and rammed to a true surface, complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of plastic emulsion paint over a coat of primer including a coat of wall care putty (minimum 1.5 mm thk) for smoothening of surfaces complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper over a one coat of primer including a coat of wall care putty for smoothening of surfaces complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of exterior acryclic emulsion weather coat paint, white or tinted, over a coat of primer complete all as specified and as directed.

S&F powder coated aluminum windows, three track, made out of aluminium sections (make Jindal or equivalent) including all necessary fittings, 5mm thick sheet glass, rubber/ neoprene beading, locking arrangements all as specified and as directed and comprises of following sections :- (a) Window frame (i) Bottom-Section 20671 (Wt not less than 0.699 Kg/m) (ii) Top & Size - 20672 (Wt not less than 0.594 Kg/m) (b) Shutter (i) Vertical (end)- 20669 (Wt not less than 0.481 Kg/m) (ii) Vertical (lock) - 20689 (Wt not less than 0.481 Kg/m) (iii) Bottom - 20718 (Wt not less than 0.263 Kg/m) (iv) Top - 20668 (Wt not less than 0.377 Kg/m)

M&L for preparation of new iron or steel surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

S&F 20 mm bore ball valves, high pressure, PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed, Minimum weight for 20mm - 210gm complete all as specified and as directed.

S&F 15mm bore medium grade galvanised iron tubing with all fittings and fixed complete to wall and ceiling or laid in floors etc complete all as specified and as directed.

S&F 20mm bore medium grade galvanised iron tubing with all fittngs and fixed complete to wall and ceiling or laid in floors etc. complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 1000ltr capacity, tripple layered, hoisted and fixed in position all as specified in SSR Part I complete all specified and as directed

S&F SS Grating with square frame (Grating thk- 1mm & frame thk- 1.5mm) of size 125mm (minimum) with waste hole complete all as specified and directed. Note: Design of grating to be approved by Engineer-in-Charge.

M&L for 20 mm bore gun metal or bronze globe / gate valve, ISI marked, screwed both ends suitable for GI tubing with side way operating GI lever handle complete all as specified and as directed.

S&F 110mm dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in floors complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified & as directed.

S&F 110mm dia PVC (SWR) bends complete all as specified and as directed.

M&L for 75 mm dia outlet PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

M&L for PVC (SWR) gully trap, 125/110 mm size, setting and jointing with solvent cement complete all as specified and as directed.

S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S&F PVC waste pipe, 32mm dia, flexible with plastic check nut for WHB or sink complete all as specified and as directed.

M&L for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite with and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed. Note:- Colour/shade shall be as approved by GE / Engineer-in-Charge.

M&L for 18 to 22mm thick machine cut kota stone slab flooring (size of kota stone slab 550mm x 550 mm), laid over and including 20mm thick screed bed in cement mortar 1:6, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and as directed.

M&L for 15 to 18mm thick machine cut kota stone on vertical surfaces such as skirting/ dado, riser of steps, laid over and including 10mm thick backing coat in cement mortar 1:4, and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for 18-20mm thick marble (of any type) work as in border strips of 100-150 mm width in kota stone flooring and like in cement mortar (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble complete all as specified & as directed. Note:- Colour/shade shall be as approved by GE / Engineer-in-Charge.

M&L for machine cut cudappah stone slab 20-25mm thick as in cooking platform etc including cutting chases in brick wall and fixing the slab in cement mortar including rubbing and polishing complete all as specified and as directed.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 610mm x 460mm bowl size 560mm x 410mm x 250mm including waste pipe complete all as specified and as directed.

Demolition and breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar, internal dia of pipe 150mm all as specified and as directed.

M&L for 150 mm internal dia reinforced cement concrete pipes, class NP2, laid and jointed in cement mortar with collars complete all as specified & as directed.

M&L for concrete bed to drain pipes in PCC 1:4:8 type D2 using 40mm graded stone aggregate including packing under and haunching against the sides of the pipes after they are laid and tested for 150mm internal dia pipes complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2 as in sub base of flooring etc complete all as specified as directed

M&L for precast cement concrete interlocking tiles 60mm thick factory made, hydraulically pressed cemented tiles of grey cement with pigments, chamfered edge, with glossy finish of M-35 grade and approved colour, design, pattern, size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed Note : Size, shape & pattern of tiles shall be as approved by GE.

M&L for precast cement concrete interlocking tiles 80mm thick factory made, hydraulically pressed cemented tiles of grey cement with pigments, chamfered edge, with glossy finish of M-40 grade and approved colour, design, pattern, size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed Note : Size, shape & pattern of tiles shall be as approved by GE.

Providing and Laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3, including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), inlcuding making drainage wherever required complete all as specified and as directed.

M&L for plain cement concrete, 1:2:4 type B1 (using 20mm graded stone aggregates) as in kerbs / filletting to sides of interlocking paver blocks, finished even and smooth without using extra cement including formwork if required complete all as specified and as directed.

M&L for plain cement concrete, 1:3:6 type C2 (using 40mm graded stone aggregates) as in foundations, filling of post, and mass concrete, etc complete all as specified and as directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following courses of treatment/specification from bottom to top:- (i) Surface roughening concrete slab by picking, sweeping clean and washing down with water to remove dust etc and applying cement slurry @3kg/Sqm. (ii) Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 as in roof slab with mixing of WPC (3% of cement content) and surface finished even and smooth using extra cement. (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986. (iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be laid/ applied over bituminous primer as specified above, application of polymeric membrance shall be by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (v) Applying one coat of aluminum paint over the APP modified membrance @ 0.11Kg/sqm.

Excavation in post holes, in any type of soil (Avg of soft/loose and hard/dense soil) each not exceeding 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick, watering and removing surplus soil to a distance not exceeding 50M and making good surface complete all as specified and as directed.

S&F prepainted galvalume aluminum zinc coating GI based corrugated/ Trapezoidal steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete all as specified & as directed. Note:- Colour & Pattern shall be as approved by GE/Engineer-in-Charge.

S&F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa fixed with self tapping screws as specified & as directed. Note:- Colour shall be as approved by GE/Engineer-in-Charge.

S&F rolled mild steel section work as in main and cross beam, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates and cooler stand and similar work confirming to Fe 410W(Gde E-250 quality A) complete all as specified and as directed

M&L for rolled mild steel work as in roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections conforming to Fe 410-W(Gde-E250) quality A) including distance pieces, cleats etc. all as specified and as directed.

Grubbing up tree trunk girth of tree exceeding 30cm and not exceeding 100cm including cutting of trunk portion protruding over ground, digging out roots, filling holes and leveling off ground, stacking of serviceable material and removing of unserviceable material to a distance n exc. 50 m and clearing site all as specified and directed.

Supply and fix white board of size 1200 x 2400 mm with triple coated steel surface with a top coat of acrylic resin over galvanised steel base, smooth and glossy surface for easy writing, with chrome plated corners complete all as specified and as directed. Make : Astra chrome plus of ALKOSIGN or equivalent as approved by GE

Supply and fix felt notice board of size 900 x 1200 mm with anodized aluminium frame,premium felt fabric of any color and back covered with laminate sheet and metal hanging brackets complete all as specified and as directed. Make: Platinum series of ALKOSIGN or equivalent as approved by GE Note: Color of felt of notice board to be approved by Engineer-in-Charge.

M&L for point wiring complete, concealed type with two runs of 1.5 sqmm for phase and neutral single core multistranded copper conductor cable of 1100 Volts grade PVC insulated and unsheathed, FRLS cable drawn through and including PVC rigid conduit not less than 20 mm dia with its accessories (ISI marked) with modular cover plate with frame and modular metal flush boxes, blank plate for mounting fitting & fixtures like switches, sockets and fan regulators etc with and including 1.5 Sqmm copper conductor cable (multistranded) PVC insulated and unsheathed FRLS cable as earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end all as specified and as directed for one light Point/fan point controlled by one way Switch complete all as specified and as directed. NOTES: (a) Proper colour coding shall be adopted for wiring (for Phase- RED, YELLOW, BLUE for Earth - Green and Neutral - Black. (b) All points shall be earthed up to fixtures i.e holdrs, tube lights all lights, ceiling lights, bldg security lights etc. (Note: The unit rate quoted shall deeemed to be included cutting chases in walls for concealed wiring & making good disturbed surfaces.

All as per serial item No 91 above but for one 3 pin socket outlet 5 Amps on same board with other switches complete all as specified and as directed.

All as per serial item No 91 above but for one 3 pin socket outlet 5 Amps on Independent board complete all as specified and as directed.

All as per serial item No 91 above but for power point 5/6 pin Socket outlet 15 Amp with PVC insulated and unsheathed, FRLS cable 2.5 Sqmm on independent board complete all as specified and as directed.

S&F modular switch single pole, one way 6/10 Amps 1 module complete all as specified and as directed

S&F modular switch single pole, one way 16 Amps, 1 module complete all as specified and as directed

S&F modular socket 6 Amp-2/3 pin combined 2 module complete all as specified and as directed.

S&F modular socket, 6 A/16 Amp -2/3 pin combined 2 module complete all as specified and as directed.

S&F ceiling rose surface bakelite three terminal type complete all as specified and as directed.

S&F decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient of capacity 20 Watt , 6500 K with inbuilt driver complete fitting and all other accessories fitting arrangements including connecting up with copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make : HAVELLS Cat No LHEXACP7IN1W020 or equivalent model of makes specified.

S&F decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient of capacity 10 Watt, 3000 K with inbuilt driver complete fitting and all other accessories fitting arrangements including connecting up with flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make : HAVELLS Cat No LHEXACP5IN1W010 or equivalent model of makes specified. .

S&F Emergency/Inverter tube light decorative ultra slim/ square profile LED lighting fixture with extruded polycarbonate , environmental friendly, energy efficient of capacity 20 Watt , 6500 K with inbuilt driver, luminous efficiency 90 LM/watt, complete fitting and all other accessories fitting arrangements including connecting up with flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make: HAVELLS Cat No LHEXASP7IN1W020 or equivalent model of makes specified.

Supply & fix Emergency/Inverter lamp with Emergency Back up up to 3-4 Hrs High grade thermal plastic housing with Al Heat sink for better thermal management , 100 lumen/watt PF>0.90 operating voltage 100 to 300 V Eco friendly (No Mercery ) CCT 6500 of capacity 12 watt complete all as specified and directed by Engr in Charge. Make: HAVELLS Cat No LHLDDDEAIB5R012 or equivalent model of makes specified.

S&F lamp holder, PVC/Polycarbonate type with back plate suitable for batten/pendant fitttings complete all as specified and as directed.

S&F PVC plastic body exhaust fan of size 300 mm sweep with louvers complete including making hole in wall and plywood packing work etc as per site requirments complete all as specified and as directed.

S&F ceiling fan complete with blades, down rods, regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) including Electrical connection with PVC 1.5 Sqmm 2 Core wire from ceiling rose to fan complete all as specified and as directed .

S&F MCB DB double door 4 way TPN with suitable Amp rated busbar 240 V complete all as specified and as directed.

S&F MCB DB double door 8 way SPN with suitable Amp rated busbar 240 V complete all as specified and as directed.

S&F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp 240 Volts complete all as specified and as directed

Supply and fix MCB SP, C Curve, 6 to 32 Amps 10 KA AC 230 volts complete all as specified & as directed.

Supply and fix MCB SPN, C Curve, 40-63 Amps 10 KA AC 230 volts complete all as specified & as directed.

Supply and fix MCB TPN, C Curve, 40-100 Amps AC 415 volts complete all as specified & as directed.

Supply and fix in repair, MCCB 4 Pole, 200 Amps 36 KA current carrying capacity,50Hz,415 volts with adjustable thermal magnetic release and connection with proper lugs complete all as specified & as directed.

Supply and fix in repair, MCCB 4 Pole, 400 Amps 36 KA current carrying capacity,50Hz,415 volts with adjustable thermal magnetic release and connection with proper lugs complete all as specified & as directed.

M&L for sub main wiring with 2 runs of 6 sqmm, single core, FRLS PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including concealed 20 mm dia non metallic PVC conduit conforming to IS-9537 with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 6 sqmm single core FRLS PVC insulated & unsheathed copper conductor cable as continuos earth wire connected to earth dolly and connecting to existing main switch board / distribution board of each building and testing on completion all as specified and as directed. Note : Three runs of 6 Sqmm cable and one run of PVC conduit will be measured as one Rm unit.

S&F post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete including suitable size of GI Pipe as per lamp size including connection and testing complete all as specified and as directed.

S&F security light of building with single piece, new generation energy saving and environmental friendly long life LED 35W made up of pressure die cast aluminium housing with acrylic covers as diffuser with IP66 protection and impact resistance of IK07 including one bracket made of Light grade GI Pipe 25 mm dia 1.5 mtr long fixed to wall/ pole with two clams made out of MSFI 40 mm x 5 mm and connect to nearest electric supply by three core 1.5 sqmm aluminium cable all as specified and as directed. Make : Havells Cat No ENDURACITYLITEPLAT PLUSSL35WLED757SASYBOPC or equivalent model of makes specified.

Taking out existing LT UG cable of any type or size including PCC/ brick covers and disconnecting of electric connection complete all as specified and directed. Note : Excavation earthwork shall be measured and paid separately.

Laying only in trenches or fixing or passing through pipe, LT UG cable retreived from above item, including required cable glands, lugs, jointing material, testing and commissioning complete all as specified and as directed. Note : Excavation earthwork shall be measured and paid separately.

M&L for earthing with galvanized steel earth plate electrode 60 cm X 60 cm X 6.0 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to the GI wire 4 mm dia, by means of nut bolts, check nuts and washer of the GI . Earth wire connected upto main earth point/DBs alongwith 15mm dia GI medium grade protection pipe, including provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick RCC (1:2:4) cover with reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 m, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point including testing on completion complete all as specified and as directed.

Supply and laying in trenches or passing through pipe or fixed on surface XLPE insulated, armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade of size 50 sqmm 3.5 core complete all as specified and as directed.

Supply and laying in trenches or passing through pipe or fixed on surface XLPE insulated, armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade of size 35 sqmm 3.5 core complete all as specified and as directed.

Supply and laying Double Walled Corrugated (DWC) HDPE pipe of outer dia 50mm and internal dia 38mm including 90 degree bends with coupler and rubber ring laid in trenches for cable protection complete all as specified and as directed.

S&F 50 mm bore, galvanised steel tubing, light grade, ISI marked, for protection of under ground cable on pole/wall/under road including taking out old unserviceable pipe complete all as specified and as directed.

Supply, installation ,testing and commissioning of LT panel Outdoor type factory fabricated front opneable with locking arrangements compartmental type made out of 3.15 mm thick CRCA sheet epoxy painted and two coats of synthetic enamel Paint over a coat of red oxide , of size 750 mm x 600mmx 550mm complete mounted on and including MS angle Iron frame made out of 40x6 mm thick of suitable size painted with black synthetic enammed paint over a coat of red oxide primer embedded in PCC (1:2:4) type B-1 in foundation up to the depth of 200 mm and 100 mm above ground level with suitable size & No of Cable glands and including necessary cable connection excavation and earth work suitable for housing and including the following accessories:- (a) MCCB 125 Amp 4 pole 25 KA with overload & thermal release setting -02 No(incoming) , 01 No as stand by (b) MCCB 63 Amp 4 pole 25 KA with overload & thermal release setting -02 No(outgoing) (c) MCB SPN 40 Amps 10 KA -01 No(outgoing) (d) MCB TPN 40 Amp, 10 KA -01 Nos(Outgoing) (e) Copper bus bar 150 Amp with 4 strips of suitable size-01 Set (f) LED type indicator lamp -01 Set (03 Nos) (g) Multifunctional Energy Meter (Voltage,Amp& Frequency)

M&L for cutting the existing road/hard standing surfaces to a depth of 60cm and 50cm width and getting out for laying under ground cable/water pipe including returning filling in, watering well ramming in layers not exceeding 25cm in soil and filling the top 15 cm thick with PCC type B2 1:2:4 (using 20mm graded stone aggregate), making good the disturbed surface complete all as specified and as directed.

Supply and laying 80 mm bore GI tubing, medium grade laid in trenches /walls/ducts or under floors including all necessary fittings, including jointing and testing complete all as specified and as directed.

Supply and laying 50 mm bore GI tubing, medium grade laid in trenches /walls/ducts or under floors including all necessary fittings, including jointing and testing complete all as specified and as directed.

Supply and laying 40 mm bore GI tubing, medium grade laid in trenches /walls/ducts or under floors including all necessary fittings, including jointing and testing complete all as specified and as directed.

Supply and laying 25 mm bore GI tubing, medium grade laid in trenches /walls/ducts or under floors including all necessary fittings, including jointing and testing complete all as specified and as directed.

Supply and fix 50 mm bore Gun metal globe or gate valve (ISI marked), with iron wheel head, screwed both ends and fixed including testing complete all as specifed and directed.

Supply and fix 25 mm bore Gun metal globe or gate valve (ISI marked), with iron wheel head, screwed both ends and fixed including testing complete all as specifed and directed.

Taking up or down unserviceable CI/GI pipe of any size including all fittings from trenches for rerouting/ relaying complete all as directed. Note : Excavation earthwork shall be measured and paid separately.

Laying only in trenches CI/ GI pipes of any size retreived from above item including all fittings required complete all as directed. Note : Excavation earthwork shall be measured and paid separately.

S&F in repairs Sluice valve cast iron 80 mm bore long body both ends flanged as per IS-14846 and drilled with stainless steel spindle, iron wheel head and as per pressure rating PN 1.6, Class I, ISI marked alongwith nuts, bolts, washers , gaskets etc. and fixed in position including dismantling and taking out old unserviceable sluice valve from valve chamber / trenches etc complete all as specified and directed by Engr in Charge.

M&L for valve chamber of size 600mmx 600mm x 450 mm including MS cover complete including necessary earth work in any type of soil ,PCC 1:3:6 in base concrete 100 mm thick , brick work in CM(1:6) with 10 mm thick plaster internally and 15 mm thick externally in CM (1:4) with 3 mm thick MS sheet cover with hinges and locking arrangements with Pad lock fixed to angle iron frame made out of 50mmx50 mmx6 mm MS angle complete with two coats of synthetic enameled paint over a coat of red oxide on all steel work and three coats of white washing on plastered surface of valve chamber complete all as specified and directed.

M&L for valve chamber of size 900mmx 900mm x 900 mm including MS cover complete incliding necessary earth work in any type of soil ,PCC 1:3:6 in base concrete 100 mm thick , brick work in CM(1:6) with 10 mm thick plaster internally and 15 mm thick externally in CM (1:4) with 3 mm thick MS sheet cover with hinges and locking arrangements with Pad lock fixed to angle iron frame made out of 50mmx50 mmx6 mm MS angle complete with two coats of synthetic enameled paint over a coat of red oxide on all steel work and three coats of white washing on plastered surface of valve chamber complete all as specified and directed.

Material & labour for earthing with Galvanised Steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised Iron strip of 32 x 6 mm as earthing lead (upto the body of the equipment) by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and protected by light grade 40mm dia GI pipe connected to main switch board or main control board and GI pipe medium grade 20mm bore for watering and including funnel , wire mesh , RCC pit cover and PCC chamber pit with PCC (1:3:6) type C-2 using 40mm graded stone aggregate, including excavation and earth work in any type of soil , returning , filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate No 3 of SSR 2020(Part-I) complete all as specified and directed

M/s.M G Kulkarni (BID ID -3197673)

ASHWAMEDH ENGINEERS (BID ID -3197392)

M/s S.R lahoti (BID ID -3197437)

sonu enterprises (BID ID -3197227)

B.R.ANAND (BID ID -3197188)

M/S. M.A. Sharief engineers and contractors (BID ID -3197560)

M/S Tirupati Goroba Shendge (BID ID -3197314)