SPL REPAIR REPLACEMENT OF PCC POLES ACSR CONDUCTOR WITH CONNECTED ITEMS AT VARIOUS LOCATIONS AND CABLES WITH CONNECTED ITEMS FOR PERIMETER SECURITY OF FD REGT UNDER GE N AKHNOOR

Taking down old unsv PCC poles and Supply and fixing Steel tubular swaged poles 9.00 mtr long type 410 SP-31 complete with cast iron base plate, final taper plug, bolts, nuts, screws as specified and directed.

LED street light fitting 70 watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed

Taking down burnt cable and Supply, laying, jointing and testing XLPE cable insulated, armoured, earthed, heavy duty electric cable with aluminium conductor , 1100 Volt grade, cross sectional area 16 sqmm 4 core including necessary cable lugs, glands, insulation tape etc complete all as specified and as directed. Make: Polycab, Grandlay, Havells & KEI

Supply and fixing weather proof flat three Core PVC insulated & sheathed Copper stranded conductor cables 1.0sqmm drawn through street light pole duly making the hole upper and down both place and connection the street light to DB Box all as specified and directed.

15mm bore light grade for protection of cable including etc complete for fixing along pipe fixed along pole complete all as sp[ecified and directed.

Bracket made out of GI Pipe 40mm dia 1.5 meter long and both end hole for fixing of street light for MS Clamps, back plates fabricated from structural steel scetion 50 x 6mm, including nuts, bolts, washers welding cold or hot, drilling of holes for bolts, in any shape or size including two coats of Aluminium paint over a coat of Red Oxide primer after preparation of steel surfaces complete all as specified and directed.

Loop In and Loop Out Box pole mounted out door type Hot press Moulded SMC Junction Box of inside dimension not less than 300x300x150mm and outer dimension of 400x400x200mm with locking arrangement suitable for 240 V, 50 Hz including MCB SP of 6 Amp cap, fixing with 4/2 Nos Aluminium busbar of 30 Amp rating for Three/single phase with neutral, painted with powder coating in siemens grey colour including clamp for fixing with steel pole all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 600mm x 600mm x 6.0mm thick buried directely in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres below ground level, connected to and including galvanised strip 32x6mm by means of bolts, nuts, check nuts and washers of galvanised iron and light grade protection pipe of 40 mm dia from earth electrode up to test point or up to 7.5mtr whichever is less by means of GI bolts, nuts, check nuts and washers all as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh, including charcoal, salt packed all around the earth electrode plate in layers, PCC earth pit chamber 1:3:6 type C1, of size 45cm x 45cm x 45 cm,RCC cover 1:2:4 type B1 of size 45x45x6 cm, excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required value including removing old item complete all as specified and directed. Note:- The required resistance of Earthing shall be less than 3 ohm, If not found to the required resisstance, the contractor has to re earthing for required resistance and the cost for the same included in the quoted rate and no extra shall be paid on failure of getting required resistance.

Testing and commissioning of control station which is capable to control 230 V i/p supply with the control relays & contractors for street light application. panel is made up of 1.6 mm crca sheet powder coated with seven step process chemical treatment and coated with RACL 7032 siemens Greay Code, Panel should have one key lock arrangement or digital door lock, to prevent unauthorized operation. The panel should have adequate space to handle future expention for CPU controlling with logical control relays. Panel Make:- Dvepl/Siemens/ASPL. Make of Contractor/MCCB/MCB:- L&T/Schenider/Siemens The panel should be cpomplete include following material (ii) Phase Indicator RYB 220 VLED type - 03 Nos (iii) Auto to Manual Control System or Vice versa- 01 No (iii) Contactor 63 A 220 V AC 3 (Per Phase)-09 Nos (iv) 1.5KW sensor/timer based automatic switch (v) Control MCB/Fuse (Single Phase) - 09 Nos (vi) Bus Bar AL 20 A 3 Phase 4 Wire (vii) Control MCB 6A SP-09 Nos (viii) The system should be compatable with PLC system through ireless/hardwire connection with the existing SSLC through Control Cables. The system is capable to control all the three phases seperately/Independently or of all three phases at a single time. this system works as a slave to the master controller SSLC and should be complete in all respects including all Electrical/Electronic Hardware or software.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for foundation of laying cable including getting out in soft/loose soil complete all as specified and directed.