Repair cum renovation of Triple Storey Office building at Sector-16 Gurugram

Amount

Supply and Planting Lolina plant having 2-3 ft height with Coco-peat, mud and manure complete.

Supply and Planting Seaforthia Palm having ht. 90cm to 1.20 m with 6-8 suckers, well developed, fresh and healthy lush green leaves from bottom to top complete.

Supply and Planting Rhapis Palm having ht. 90cm to 1.20 m with 15 to 18 equal suckers, well developed, full of fresh and healthy leaves from bottom to top complete.

Supply of full soil fill conical shaped planters of make : vaso eco, model no: c-series: of specified volume and dimensions in stone finish or equivalent. planters to be indigenously made by rotational moulding, with homogeneous recyclable, industrial grade polymer-resin mix, and textured surface. planters should have an integrated water outlet hole and plug, single layered peel-proof construction, light weight, rust proof, uv stabilized, anti-frost feature without any joints, and easy to clean. planter supplier must give 1 year warranty against any fading or cracking for both indoor and outdoor use. green plant and laying is extra. potting instructions as per company catalogue. - C-1613 - 40 (D) X 33(H) CM : V- 27LTR

Supply, Installation, Testing and Commissioing of Recessed downlightwith HPE (High-Performance Efficiency) with LED (Light Emitting Diode), system power: 12 W, Luminous flux of luminaire 1320 lm, 110 LM/W system efficacy, Colour temperature of 4000 K, Neutral white, CRI ) 80, 230V constant current driver, 70% of luminous flux after 50,000 operating hours: energy-efficient LEDs, direct light emission, housing in die-cast aluminium, Polyester powder white coloured coat applied over a 5-stage pre-treatment trim, prismatic diffuser for homogenous light distribution, ZHLS (ZERO HALOGEN LOW SMOKE) wiring, Electronic control gear, Protection class II, IP 40, Ø = 175 mm, DA(Ø) = 160 mm, H = 59 mm

Supply, Installation, Testing and Commissioing of COB based surface mounted/pendent downlight, system power: 10W, 110 Lm/W, luminous flux of luminaire 1100lm, colour temperature of 4000K, 230V constant current driver, 70% of luminous ?ux after 50,000 operating hours: energy e?cient LEDs, direct light emission, housing in aluminium, round, polyester Silver powder coat applied over a 5-stage pre-treatment, aluminium reflector, 50x80 elliptical beam, Electronic Control Gear, Protection class I, IP20, Ø = 100 mm, H = 165 mm

DSR VRF 5.4 Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

DSR VRF 5.2 Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply,installation,testing and commissioning of PVC drain water with necessary clamps, fittings such as bends tees etc. and duly insulated. - 32 MM DIA

Modular kitchen - Under counter storage cabinets: Providing and fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and sufficient number of drawers made of 18 mm thk. ISI Marked comm. ply , all ply to be laminated with 0.8 mm laminate.All shelves should be supported on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at least 18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters finished in high gloss acrylic of approved make- Rehau,Ornare,Senosan. The cabinet boxes of floor units will be supported by 100mm height vertical adjustable legs (Hettich make) which will be covered with PVC skirting (Rehau or equivalent make ) in brushed aluminum finish attached by hardware of skirting. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and rawl plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be considered for measurement and payment. Cabinet boxes size would be varies from 400X560X710MM to 1000X560X710MM (approx.) and join together as per site requirements etc.

Modular Kitchen - Overhead storage wall units: Providing and fixing factory made modular kitchen cabinets in modular type knockable cabinet boxes with openable shutters and sufficient number of drawers made of 18 mm thk. ISI Marked comm. ply . all ply to be laminated with 0.8 mm laminate.All shelves should be supported on approved quality SS pins and shall be adjustable for different heights as per requirements.Shutters and drawers fascia shall be at least 18mm thic with laminate on both sides with 18mm wide 2mm thick PVC edge banding, All Shutters finished in high gloss acrylic of approved make- Rehau,Ornare,Senosan. The unit shall be fixed to the floor/ wall/slab using metal screws of appropriate size and raw plugs. Only front face area of cabinets and skirting from floor to top of boxes shall be considered for measurement and payment. Cabinet boxes size would be varies from 400X560X710MM to 1000X560X710MM (approx.) and join together as per site requirements etc.

Supply of ISI marked domestic exhaust fan plastic ideal for mounting on glass window with 200mm sweep (Havells Cat No. Ventilair DX 200mm sweep or equivalent)

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with required suitable number of GI couplers for joining raceways and fixing GI brackets and all accessories complete in all respect as per the directions of engineer in charge (D) 100mmx38mm (GI)

Supply and fixing of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium Conductor Cables : Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively and ISI marked. - 4 C x 25 sqm XLPE cable

Providing and Fixing of GI Clip in perforated Metal Ceiling System of 300x1200 mm module which includes providing and fixing wall angle of size 20x20 mm made of 0.4 mm thick and 35 x 75 mm made of 0.5 mm pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm centre to centre, suspending the main C carrier of size 10x50x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1200 mm c/c.

GLASS FILM Providing and Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to reproduce Sand-blasting effect on glass with customised designs, thickness of 2 mil (0.05mm) without adhesive and 3mil (0.8)with adhesive having minimum tensile strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors) must be endorsed by 3M India Limited Architectural Market Department. Contractors payment wouldn`t be released until and unless he/she produces orginal warranty certificate from the manufacturer.

SINGLE GLAZED TOUGHENED GLASS PARTITIONS-with SYSTEM-50 FRAME PROFILES: Supply and installation of Aluminium Framed Glass Partition for Access and Cabin System for minimal frame, room dividing solutions. Single glazed mullion free demountable glass partition using Toughened/ Laminated glass in proprietary natural anodised/Black aluminium sections ALT 50 of size 50mm x 30mm with Concealed sealing (No visible Gasket).The profile will have Carpert Groove at the Bottom on both sides for accomodating max. 8mm carpets. THe Glass to be fixed with help of Proprietary Stability GRIPPER Clamp to have a stable system. It should consists of intermediate slim junction profiles for Glass to Glass vertical joints, 90 Degree L Junction and T Junction profiles suitably to be used as per room configuration designs.No VISIBLE Clip Lines to provide clutter free view at both side of section. The Glass to be Offset mounted towards outer edge leading to minimum aluminium frame on one side. Optional Profile Bottom Seal pair for additional accoustic. Glass thickness - 10( LSG).shall be included in the product.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 1200x600mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 1200x600mm FOR SKIRTING ONLY

PandF Cpvc union in cpvc pipeline including Cuttings and threading the pipe complete 15 mm dia nominal bore union

PandF CPVC union in cpvc pipeline including Cuttings and threading the pipe complete 20 mm dia nominal bore union

Providing and fixing of PVC Cowl 100 mm dia complete in all respect to the entire satisfaction of engineer in charge.

Providing and fixing of PVC floor trap 100 mm dia with CP jali complete in all respect to the entire satisfaction of engineer in charge.

Providing and Fixing of PVC Wall Panelling complete in all respect to the entire satisfaction of engineer in charge

providing of 2`x2` false ceiling light 35 Wto 48 W of phillips make complete in all respect as per direction of Engineer in charge

50MM THICK GI FRAME (FOR THICK PARTITION) for MDF : Providing and fixing metal system up to ceiling height, which includes frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 GSM, consisting of Boral U track 52mm wide having equal flanges of 30mm and 0.55mm thick (Base metal thickness) fastened to the floor slab and ceiling soffit using rawl plugs with screw at 600mm centers, with first and last fixing point at not greater than 50 mm from either end. Boral C studs 50mm wide having one flange of 34mm, other flange 36mm, lip size 6 mm and 0.55mm thick installed perpendicularly within the flanges of floor and ceiling channels located directly opposite to each other at not more than 610mm centers. Maintain 5 to 10mm gap between C Stud and web of U Track

Providing and fixing zebra blinds on windows complete.

WPC WALL PANELLING : Providing and Fixing WPC Wall panelling as per approved make and pattern as approved by the client and architect.

Supply, Installation, Testing and Commisioning of 1 x 4 ft LED Panel with HPE (High-Performance Efficiency), system power: 23 W, Colour temperature of 6500 K, CRI ) 80, 230 V constant current driver, 70% of luminous flux after 50,000 operating hours: energy-efficient LEDs, direct light emission, Polyester powder black coloured coat applied over a 5-stage pre-treatment, Opal diffuser for homogenous light distribution, electronic control gear, Adjustable wire suspension,Protection class II, IP 20, L = 1200 mm, B = 600 mm

Providing and Fixing High Density Fibre (HDF) Laminate Flooring in different colour and shape having thickness 8 mm laid over 1 mm thick damp proof foam all complete.

`Providing and fi xing Stainless Steel 304 tower bolts 24 INCHES with nuts and screws etc. complete (OZONE model no -OZ-TB-S 24`` or approved equivalent)`

HOLLOW SS LEVER HANDLE ON ROSE WITH EUROPROFILE CYLINDER ESCUTCHEON , SS MATT (Hafele GEZE 19mm dia lever handle Suitable for 40 to 50mm door thickness, Grub screw fixing onto 8mm x 100mm spindle. For Wooden Doors IN PAIR (Hafele 98302002 or equivalent) `a) GEZE 55mm backset Mortise sash lock, 20mm stainless steel square forend, 72mm center to center with strike plate. With screws for Timber doors/Metal doors (ONE NO.).(Hafele 98484001 or equivalent) b) GEZE 52mm dia with 38mm fixing centers supplied with stainless steel structure 8mm thick (ONE NO.) (Hafele 98482002 or equivalent)` 5 pin Euro profile knob cylnder with 3 keys, 70mm length (ONE NO.) (Hafele 98245213 or equivalent)

Providing and fixing Stainless steel SS 304 grade satin finish Half moon shape floor mounted door stopper of dia 44mm x 32mm with SS screws of approved make and model all complete as per directions of Engineer-in-charge

Providing and Installation of Baffle ceiling system comprises of 50 mm x 100 mm (50 mm width and 100 mm Height) U Shape panels in RAL color finish. Panels shall be made of 0.5 mm thick galvanized steel after Powder-coated and length up to 4000 mm. Panel shall be high corrosion resistance and good color stability. Centre to Centre panel gap will be 150 mm. Panels are fixed on to roll formed carriers 20 mm wide x 40 mm deep out of 0.80 mm G.I sheet Powder-coated color with cutouts to hold the panels in module of 50 mm at maximum 1200 m c/c. Carriers are suspended from the roof or truss by 6 mm dia. galvanized steel wire rod hanger with special height adjustment suspension clip at max. 1200 mm c/c. Hangers are fixed to the roof by ‘J’ hooks or ceiling brackets and nylon inserts. Panels are factory cut in lengths up to maximum 4.0 m to suit site dimensions or shop drawings. Top cap and side cap are used to cover the edges of the panels.

PROVIDING AND FIXING IN POSITION SOAP DISPENSER WITH GLASS BOTTLE WITH NECESSARY FITTING ARRANGEMENTS , COMPLETE AS PER DIRECTION OF THE ENGINEER IN CHARGE (JAQUAR CAT NO. ACN-1135N OR APPROVED EQUIVALENT) etc

providing and fixing stainless steel towel rail jaquar Cat no AQN-7711

Providing and fixing C.P. brass pillar cock of approved quality conforming to IS:8931 :15 mm nominal bore JAQUAR MAKE

Providing and fixing Two in one Angle valve (Jaquar, kohler, equivalent or above make) Angular stop cock with wall plaxpe etc. (make Jaquar) Complete in all respect as per specification and entire satisfaction of Engineer -in-charge

PandF handle stainless steel 11` long all complete as per the directions of Engineer-in-charge

Providing and Fixing table top wash basin withh all accessories Set all complete of jaquar make.

Labour charges for Installation, testing and commissioning of split Ac 1.5/2 tonne including service and repair if required with all accessories complete in all respect.

Providing and fixing cupboard / wardrobe including shutters sunmica handles etc complete in all respect

Brick tile obtained during dismantling of roof tiles (CREDIT TO WORK)

Brick bat obtained during dismantling of roof tiles (CREDIT TO WORK)

credit to work Dismantled Iron from old broken scraps

Dismantled Aluminium ( Credit to Work)

Bidder Name

Amount

Dal Singh Atri Contractor (GSTN-06AUIPS1758B2ZM) BID ID -1287230

G L GOLDEN (GSTN-NA) BID ID -1280190

Dynamic Developers (GSTN-NA) BID ID -1284449

G L GOLDEN (BID ID -1280190)

Dal Singh Atri Contractor (BID ID -1287230)

G L GOLDEN (BID ID -1280190)

Dal Singh Atri Contractor (BID ID -1287230)