COMPREHENSIVE REPAIR TO CERTAIN B/R WORK FOR SF ACCN, WELCOME MAINT TO CERTAIN MD ACCN AND REPAIR/REPLACEMENT OF ROOFING AND CONNECTING WORKS FOR ZONE B UNDER AGE B/R-II AT GE JHANSI

Amount

Dismantling Asbestos Cement (Corrugated or Semicorrugated) sheet in Roof covering including J or L hookes & removing from site complete all as specified and directed.

Supply & Fixing Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering or cladding to wall, fixed with self tapping screws complete all as specified and directed. .

Supply & Fixing Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / valley/ gutter or cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling timber scantling 40 Sqcm and over in section in any position as in unframed works such as roof purlins, rafters, fillets, ridges etc as in ceiling complete all as specified & directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Supply & Fixing rolled mild steel different section (Fe 410 W, Gde E 250, Quality-A) as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing (beams, tee, angle, channels or flat iron sections) complete all as specified and directed .

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs any thickness including snap grid frame work complete all as specified and directed.

Material & labour Gypsum Board 12mm thick in false ceiling fixed with screw as per manufacturers instructions Hangers 6 mm dia & 1200mm length) adjusting level fixed to roof slabs by means of Anodised aluminium snap grid frame work for false ceilling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia & 40mm long complete all as specified & directed.

Mateial & Labour false ceiling at all heights with GRG (Glass Fibre with Semi with fully Reinforced Gypsum) false ceiling tiles of perforated boards 12mm thick & 595 x 595 mm size of approved texture, 12mm thick thick micro tegular design and patterns having moisture micro tegular edged or 10 mm content less than 2%, humidity resistance edged GRG thick square edged of 99%, NRC 0.50 to 0.75 as per IS false ceiling GRG false ceiling 8225:1987, Non-combustible as per BS tiles tiles 476 (part 4) 1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm, cross T of size 15x32mm of length 1200mm and secondary intermediate cross T of size 15x32 mm of length 600mm to form grid module of size 600x600mm suspended from ceiling using galvanized mild steel items (galvanizing @ 120 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1OOOmm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall in partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and complete all as specified and directed.

Supply & Fixing Perforet PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per site requirement complete all as specified and directed.

Demolition of brick work built in cement mortar or lime mortar including all quoins, arches, pillars etc & removing rubbish from site complete all as specified and directed.

Material & Labour for brick work with old size fly ash bricks, straight or curved on plan exceeding 6 M mean radius built in cement sand mortar 1:6 complete all as specified & directed.

Material & Labour for half brick thick wall with old size fly ash bricks, straight or curved on plan to any radius built in cement sand mortar 1:4 complete all as specified and directed.

Material & Labour for 10 mm thick rendering in CM (1:4) on fair face of brick work / concrete surfaces finished surface even & fair (without using extra cement) including taking down cement plaster on brick or stone walls, dado and skirting etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

Material & Labour for 15 mm thick rendering in CM 1:4 on fair faces of brick work / concrete surfaces, finished the surface even & fair (without using extra cement) including taking down cement plaster on brick or stone walls, dado and skirting etc including racking out joints hacking for key scrubbing down with water etccomplete all as specified and directed.

Material & Labour for 10 mm thick rendering in CM (1:4) on fair faces of brick work / concrete surfaces finished surface even & fair (without using extra cement) complete all as specified and directed.

Material & Labour for 15 mm thick rendering in CM 1:4 on fair faces of brick work / concrete surfaces, finished surface even & fair (without using extra cement) complete all as specified and directed.

Supply only liquid water proofing compound of Make : Dr Fixit LW+ mixed in CM as per manufacturer instruction complete all as specified and directed.

Material & Labour for preparation of new plastered surface of wall and applying two coat of cement based paint over and including one coat of exterior grade cement based primer complete all as specified and directed.

Material & Labour for preparation of new plastered surface of wall and applying two coats of oil bound distemper, over a coat of chalk whitening primer over and incl a layer 3mm thick of wall care putty to get even and smooth level finish on new plastered surface of internal walls complete all as specified and as directed.

Supply & Fixing of ring fit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and including rubber tighten gaskets, ring-fit sockets etc complete pipe duly fixed to walls with clamps including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

Supply & Fixing 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

Supply & Fixing 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal complete all as specified and directed.

Supply & Fixing stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110 mm bore pipe complete all as specified and directed.

Material & Labour for asbestos cement north light curves to suit asbestos cement sheets, fixed with seam bolts and nuts including L-type or J-type or cranked hook bolts etc complete all as specified and directed.

Material & Labour Plain cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses/ copings, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Supply & Fixing in repair filleting not exceeding 25 sqcm in sections in any position and to any shape in cement mortar 1:4 including all mitres, stops etc complete all as specified & directed.

Supply & Fixing in repair for 1 mm thick plain black mild steel sheeting as in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified & directed.

Material & Labour for preparation of new steel or iron surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide primer complete all as specified and directed.

Supply & Fixing of 3 mm thick figured glass pin headed type exc 0.50 Sqm in each pane & fixed with oil putty or wooden beadding as required including hacking out old broken glass (any thickness & size or description) from wooden frames or with putty or fixed with beads complete all as specified and directed. Notes: The rates in inclusive of fixing the glass panes upto 12 RM height with the help of scaffolding or ladder No separate payment will be made.

M&L for preparing old decorated surfaces plastered or unplastered of walls (if required filling putty in holes on wall surface) and applying one coat of oil bound distemper white or any tinted complete all as specified and directed.

M&L for washing rubbing down and stopping of distempered and painted surfaces and preparation of old existing surface of wall & applying two coats of oil bound distemper of white or any tinted on old walls complete all as specified and directed.

M&L for preparing old decorated surfaces plastered or unplastered of ceiling (if required filling putty in holes on wall surface) and applying one coat of oil bound distemper white or any tinted complete all as specified and directed.

M&L for complete removal of existing treatment by brushing washing rubbing down scraping from steel wire brushes old treated surfaces of wall and applying two coats of oil bound distemper over one coat of chalk whitening primer over & including one layer of 3 mm thick wall care putty to get smooth and level finish complete all as specified and directed.

M&L for preparation of old plastered surfaces and applying one coat of cement base paint on walls, facia, cornice, chajja complete all as specified and directed.

M&L for complete removal of existing treatment preparation of surface and applying two coats of cement base paint over one coat of alkali resistant priming coat complete all as specified and directed.

Material & Labour for complete removal of existing treatment and preparation of surfaces of walls by scrapping with sand paper rubbing and finally washing with water and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS:15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces complete all as specified and directed.

M&L for preperation of old or previously treated surfaces of wood or wood based materials of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint to match the existing surfaces complete all as specified and directed.

M&L for preperation of old painted steel surfaces of any description over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

Demolition of cement concrete including terrazo flooring (un-reinforced) in ground floor and paving not exceeding 15cm thick (below or above ground level) built in cement mortar & removing rubbish from site complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in sub base of flooring/ hard standing complete all as specified and directed.

Material & Labour for 75 mm thick cement concrete 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in plinth protection and path laid in panels, not more than 3 mtr in length, laid to slope 1:30 including forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) surface complete all as specified and as directed. Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings.

Material & Labour for 40 mm thick plain cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregates as in floor, finished even and smooth (without using extra cement) laid in panels using 4mm thick & 38mm wide glass strip, panels will be not more than 1.2 x 1.2 mtr in size complete all as specified and directed. Note : The quoted rates are deemed to be inclusive of 4mm thick & 38mm wide glass strip.

Material & Labour for plain cement concrete 1:2:4 type B-2 using 40 mm graded crushed stone aggregate as in foundations, filling and mass concrete for post embedment complete all as specified & directed.

Material & Labour for factory made machine pressed precast concrete interlocking paver block of any shape and size confirming to IS: 15658-2006 of 60 mm thickness having strength M-35 Grade with coloured pigment made of PVC moulded (or rubber mould) with vibrating system, laid over with and including 50mm thick sand cushioning including plastering in CM (1:3) in edges of pavers blocks complete all as specified and directed. Note : The cost of sand cushion and plastering to edges is included in quoted rates.

Material & Labour for preparation of plastered surfaces of walls and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS:15489:2004, Alkali & fungal resistance, dirt resistance exterior paint (weather proof) of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm over old surfaces complete all as specified and directed.

Material & Labour for 5 mm thick rendering in CM 1:3 on fair faces of concrete surfaces in ceiling finished even & smooth without using extra cement including taking down old cement plaster on brick or concrete surface etc including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

Material & Labour for preparation of newly plastered surfaces and applying two coat of white wash on ceiling complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removed the rubbish off the premises complete all as specified and directed.

Material & Labour for Non skid ceramic colored tiles 7-8 mm thick (square or rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm as in flooring set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

Material & Labour for ceramic colour tiles in vertical surface of size 350x250x 6-7 or 450x300x6-7 mm thick, jointless tiles set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles with and including 10 mm thick rendering in CM (1:4) for receiving the tiles complete all as specified and directed.

Material & Labour for 8-10 mm thick Vitrified tiles (Ceramic Joint free) light shed (square or rectangular) polished area of each tile not exceeding 0.36 Sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

All as per item number 52 here-in-above but on vertical surfaces such as skirting or dado over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness laid bedded and pointed in any mortar as in floors, aprons & removing from site complete all as specified and directed.

Material & Labour 20 mm thick granite slab of any type as in table top or kitchen platform rubbed, machine cut, duly grinding, polishing, moulding on all outer edges or sharp corners, duly fixed in steps, jambs, pillars, window cills, cooking platforms and like over & included 20 mm thick screed bed or bedding layer in CM 1:6 including pointing in grey cement (1:2) using marble dust with admixture of pigment to match with the shade of stone slab complete all specified and directed.

Supply & Fixing 18 mm thick pre-laminated particle board, interior grade, pre-laminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in any situation as in cup board shelves or shutter or similar work inclding dismantling of old boards in any descriptio & any position complete all as specified and directed.

Supply & Fixing continuous (piano) hinges, mild steel bright finish in electro galvanized width of flat (when open) in 30mm fixed with screws complete all as specified and directed.

Supply & Fixing drawer steel handles 80 mm fixed with steel screws complete all as specified and directed

Supply & Fixing knobs 35-40mm dia fancy type complete all as specified and directed.

Supply & Fixing 100 mm aluminium anodise hasp and staple, safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm each including cutting holes in brick or stone wall built in cement mortar, embedded portion exc half brick but not exceeding one brick thick walls and making good the disturbed portion/surfaces, in CM 1:3 complete all as specified and directed.

Taking down chowkhats with shutters (without taking off shutters from the frame) area not exceeding 1.5 Sqm each including cutting holes in brick or stone wall built in cement mortar & removing from site complete all as specified and directed.

Taking down shutters of any description not exc 1 Sqm each & removing from site complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm and not exc 2 Sqm each & removing from site complete all as specified and directed.

Material & Labour for second class hard wood plain, solid, straight chowkhats and frame, wrought framed, rebated on the solid, rounded or chamfered edge, put together with glue, pinned at joints and fixing complete all as specified and directed.

Supply & Fixing mild steel rolled section in Fe 410-W (Gde-E-250) quality-A as in framed work as in doors or gates of angle or other section with gusset plates, rails, braces complete, drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified & directed.

Material & Labour for mild steel angles, bars, flats as in hold fasts pipe clamps, angle cleats for securing purlins, supports for stiffening of fencing, wall ties and similar small articles confirming to Fe-290 Gde E-165 complete all as specified and directed.

Supply & Fixing 30 mm thick factory made modular designer flush door shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping & frame to match complete all as specified and directed.

Supply & Fixing for 35mm thick 2nd class hard wood glazed & skeleton door shutters (fully glazed or gauged) open rebated & prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered sash bar or rounded, fitted with & mitred beads for securing glass/wiremesh etc, conforming to IS-1003 Part-I & II; size of members of shutters as specified in SSR Part-I section–8, clause 8.24(a) complete all as specified and directed.

Supply & Fixing Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 70 mm (± 5 mm tolerence in dimension) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/Cum, screw with drawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners including in this item of required dia and length complete all as specified and directed.

Supply & Fixing for Factory made double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/ Cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as specified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Supply & Fixing Factory made single 35 mm thick extruded WPC (Wood Polymer Composite) solid moulded flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/Cum and screw with drawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws complete all as specified and directed.

Supply & Fixing steel window with side hung shutters including projecting type hinges with steel handle, steel peg stay complete with mild stel glazing bar dovetailed or welded complete all as specified and directed.

Supply & Fixing stainless steel wire cloth 0.36 mm in nominal dia of wire average width of aperture 1.4 mm and fixed with tinned tacks of stainless steel wire staples to wooden or steel shutters or fixed with wooden beads to wooden joinery complete all as specified and directed.

Supply & Fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

Supply & Fixing Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

Supply & Fixing powder coated (minimum thickness of powder coating not less than 50 micron) aluminium window shutter (three shutter) sliding type with frame of powder coated aluminium channel section suitable for sliding aluminium shutters weighing 0.55Kg/RM of three channel including necessary joining cleats glazing clips rubber packing powder coated aluminium shop beading screws with two shutter Including 5mm thick plain sheet glass and one shutter with stainless steel wire gauze including necessary locking arrangement and aluminium handle 100 mm complete all as specified and directed.

Supply & Fixing 5mm thick sheet glass (tinted type) each panes not exceeding 0.5 Sqm suitable for aluminium window / Ventilators / door opening and similar work fitted with aluminium snap beadings complete all as specified and directed.

Material & Labour for powder coated (minimum thickness of powder coating not less than 50 micron) aluminium ventilator shutters fixed type without sash bar, aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws complete all specified & directed.

Supply & Fixing aluminium anodised grills (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC-15) of approved design/pattern, with approved standard section and fixed to the existing window frame with steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and directed.

Supply & Fixing 125 mm butt hinges medium weight cold rolled mild steel ISI marked and fixed with steel screws or welded to angle frame complete all as specified and directed.

Supply & Fixing 200mm long barrel tower bolt aluminum anodized extruded section fixed with steel screws complete all as specified and directed.

Supply & Fixing of 150 mm long aluminium anodised pressed handles, fixed with screws, complete all as specified and directed.

Supply & Fixing of aluminium alloy anodized sliding door bolt 300mm (aldrop bolt) length with hasp staple and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all specified and directed

Supply & Fixing of mild steel ordinary rat tail rod pattern springs of size 300mm including roller and roller plate complete all as specified and directed

Supply & Fixing of 140 mm door stopper of aluminium body and tongue anodized with hard drawn steel spring fixed in door complete all as specified and directed.

Supply & Fixing 100 mm size butt hinges, extruded aluminum alloy with steel pin type B-21 anodized fixed with screws complete all specified and directed

Supply & Fixing 150mm long barrel tower bolt aluminum anodized extruded section fixed with steel screws complete all as specified and directed.

Supply & Fixing in repair aluminium alloy anodized sliding door bolt 300mm (aldrop bolt) length with hasp staple and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all specified and directed

Supply & Fixing of 3 mm thick sheet figured glass pin headed type, not exc 0.50 Sqm in each pane, duly fixed with oil putty or wooden beadding as required, including hacking out old broken glass (any thickness, size, quality or description) from wooden frames or glazed with putty or fixed with beads complete all as specified and directed.

Supply & Fixing of 3 mm thick sheet glass ordinary quality and glazing type, not exc 0.50 Sqm in each pane, duly fixed with oil putty or wooden beadding as required, including hacking out old broken glass (any thickness, size, quality or description) from wooden frames or glazed with putty or fixed with beads complete all as specified and directed.

Supply & Fixing in replacement stainless steel wire cloth 0.36 mm in nominal dia of wire average width of aperture 1.4 mm and fixed with tinned tacks of stainless steel wire staples to wooden or steel shutters or fixed with wooden beads to wooden joinery complete all as specified and directed.

Supply & Fixing in repair stainless steel curtain rod 25mm dia steel pipe (304 grade steel) cutting into length as required at site with and including SS end caps/lobs and SS wall mounting brackets fixed with screws complete all as specified and directed.

Supply & Fixing of ring fit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and including rubber tighten gaskets, ring-fit sockets etc complete pipe duly fixed to walls with clamps including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

Supply & Fixing of ring fit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc complete pipe duly laid in trenches or in floors including taking out / down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

Supply & Fixing of ring fit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and including rubber tighten gaskets, ring-fit sockets etc complete pipe duly fixed to walls with clamps including taking down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

Supply & Fixing of ring fit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc complete pipe duly laid in trenches or in floors including taking out / down of eaves gutter and rain / waste water pipes including all fittings any size and pattern complete all as specified and directed.

Supply & Fixing stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110 mm bore pipe complete all as specified and directed.

Supply & Fixing 110 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

Supply & Fixing 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed.

Supply & Fixing 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal complete all as specified and directed.

Supply & Fixing 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal complete all as specified and directed.

Supply & Fixing PVC (SWR) vent cowl 75mm bore, jointing to waste pipe with cement or adhesive complete all as specified and directed.

Supply & Fixing PVC (SWR) vent cowl 110mm bore, jointing to waste pipe with cement or adhesive complete all as specified and directed.

Supply & Fixing PVC floor trap of 75 mm outlet, jointing to waste pipe wit hcement or adhesive complete all as specified and directed.

Supply & Fixing 15 mm bore Galvanized Steel water tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open including cutting of grooves including taking up or down with connections and fittings all as specified and directed.

Supply & Fixing 20 mm bore Galvanized Steel water tubes, medium grade fixed to walls and ceilings or laid in floors, concealed or open including cutting of grooves including taking up or down with connections and fittings all as specified and directed.

Supply & Fixing of 16 mm outer dia CPVC pipes SDR-11 & Plain CPVC SDR-11 fittings in walls including taking up or down existing water tubing with connections and fittings complete all as specified and directed.

Supply & Fixing of 20 mm outer dia CPVC pipes SDR-11 & Plain CPVC SDR-11 fittings in walls including taking up or down existing water tubing with connections and fittings complete all as specified and directed.

Material & Labour for cutting chases, pinning in for concealed water tubing, not exceeding 10 cm girth and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc complete all as specified and directed.

Supply & Fixing of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered white colour 500 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making connection with GI tubing inlet or outlet connection, with and including disconnecting and dismantling the existing un-serviceable damaged PVC/RCC water tank & removing from site complete all as specified and directed.

Supply & Fixing in repair 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed inlet / out let of water tubing complete all as specified and directed.

Supply & Fixing in repair / replacement 20 mm dia of Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iorn pipe and fixed (minium weight 20 mm-210 gms) complete all as specified and directed.

Disconnecting existing water tanks, setting aside (or lowering if required) for repairs, cleaning with soda or bleaching powder etc and hoisting, reconnecting and re-fixing in any position after satisfactory cleaning of all scales in tanks of exceeding 250 litres but not exceeding 500 litres capacity of tanks inclusive of necessary tank nipple, gate valve, air pipe and float valve, date of cleaning of tank will be marked on the tank by stencil with synthetic enamaled paint in uniform size, size of letters & numbers should be 40mm complete all as specified and directed.

Supply & Fixing in repair / replacement of stainless steel sink, 1 mm thick for kitchen with plug, with and including 40mm dia CP waste coupling, waste pipe of 750mm long, washers, cantilever brackets, connecting union to pipe overall approx size 495 mm x 420 mm with approx bowl size of 410 mm x 330 mm x 160 mm complete all as specified and directed.

Supply & Fixing in repair / replacement kitchen sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs and including 40mm dia CP waste coupling, waste pipe of 750mm long washers; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified & directed.

Supply & Fixing in repair / replacement of stainless steel kitchen plate rack made out of 1 mm thick sheet of size 765x920mm and 220mm deep, weight not less than 7 Kg each & fitted on walls complete all as specified and as directed.

Supply & Fixing in replacement of pillar taps 15 mm dia cast copper alloy with capstan heads chromium plated, fancy type, screwed down high pressure with long shank screwed shanks and fly-nuts complete all specified and directed.

Supply & Fixing in replacement of 15 mm CP Brass 3-in-1 wall mixer with provision for overhead Shower with 115mm long bend pipe on upperside, connecting legs & wall flanges made of cast copper alloy, chromium plated fancy type complete all specified and directed.

Supply & Fixing in replacement of stop cock with long shank and cup (concealed type) 15mm dia with wall flange, fancy type, chromium plated, screwed down high pressure with capstan head handle screwed both ends for iron pipe / unions, complete all as specified and directed.

Supply & Fixing in replacement of overhead shower rose of dia 80 mm round shape single flow, ABS body chrome plated fancy type, with & including swivel joint type shower arm of 20mm dia with wall flange made of cast copper alloy, chromium plated fancy type complete all specified and directed.

Supply & Fixing in replacement of long body bib tap 15 mm dia with wall flange made of cast copper alloy chromium plated complete all specified and directed.

Supply & Fixing in repair Health faucet (ABS Body) chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified with wall flange complete all specified and directed.

Supply & Fixing in replacement of angular stop cock 15 mm dia with wall flange made of cast copper alloy chromium plated capstan head half or full turn complete all specified and directed.

Supply & Fixing in replacement of bottle trap 32 mm size with 250 mm long wall connection pipe and wall flange made of cast copper alloy, chromium plated fancy type, complete all specified and directed.

Supply & Fixing in repair SS grating of squre/round shape overall size of 150x150mm with hinge type openable jali of 100 mm dia size with and including fixing with CM or adhesive to floor or top of nahani trap complete all specified and directed.

Supply & Fixing in replacement of toilet paper holder with flap made of cast copper alloy chromium plated complete all specified and directed.

Supply & Fixing in replacement of towel rail 600 mm long D type between flange and wall bracket made of cast copper alloy chromium plated complete all specified and directed.

Supply & Fixing in repair sheet glass shelf assembly consisting of 5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Supply & Fixing in replacement of PVC multipurpose cabinet mirror with front openable door of overall size 350 x 450 mm complete all as specified and directed.

Supply & Fixing in replacement of PVC waste pipe 32 mm dia 750 mm long with for wash hand basin or for kitchen sink complete all as specified and directed.

Supply & Fixing in replacement of waste coupling chromium plated (half or full threaded) 32 mm dia size complete all as specified and directed.

Supply & Fixing in replacement of waste coupling chromium plated (half or full threaded) 40 mm dia size for kitchen sink complete all as specified and directed.

Supply & Fixing in replacement of PVC connection 450 x 15mm dia PTMT (PVC) complete all as specified and directed.

Supply & Fixing in replacement of PVC connection 600 x 15mm dia PTMT (PVC) complete all as specified and directed.

Supply & Fixing in replacement of plastic seat with covers for (EWC) water closet, of existing colour, closed pattern with flat bottom with chromium plated hinging device complete all as specified and directed.

Supply & Fixing in replacement of 10 ltr capacity PVC valve less symphonic action type flushing cistern, white colour with inlet ball valve, float and handle with and including wall bracket 32 mm dia PVC flush pipe and connected to squat pattern / pedestal pattern water closet including all joints and making good to the wall & floors complete all specified and directed.

Supply & Fixing in replacement of 1st quality vitreous china ware European type EWC with "P" or "S" traps and including same make plastic seat cover of white colour including flush pipe, fixing bolts etc and making good of the wall & floor surface complete all as directed & directed.

Supply & Fixing in replacement of 1st quality vitreous china squatting pan Orissa pattern of size 580x440 mm, white colour with integral foot rests water closet including flush pipe, P-trap and connecting but exluding flushing cistern, duly fixed in lime concrete bedding and making good of floor surface complete all as specified and directed.

Supply & Fixing in replacement of 1st quality vitreous china wash hand basin, white colour flat back of size 550x400mm, complete including necessary cutting for and pinning in ends of brackets with and including wall brackets, PVC waste pipe of 750mm long, CP waste coupling of 32mm dia size, complete all as specified and directed.

Material & Labour for preparing new or previously untreated surfaces of wood or wood based materials of any description not otherwise described exceeding 10 cm width or girth and applying two coat of synthetic enamel paint over and including one coat of pink primer and layer of putty/filling material to get smooth & level finish, complete all as specified and directed.

Material & Labour framed work such as grills, gratings etc with ends of bars shouldered or riveted or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290-Gde-E-165 complete all as specified and directed.

Supply & Fixing in repair 15 mm bore Brass CP kitchen sink mixer for mixing hot & cold water screwed down for iron pipe and fixed in GI water tubing complete all as specified & directed.

Supply & Fixing in replacement of Corner glass shelf 300 mm with Chromium plated bracket guard and railing and fixing accessories complete all as specified & directed.

Demolition of RCC Not exceeding 15cm thick Roofs, floors (other than ground floors) beams stairc ases landing chajjas, Cover slab and similar suspended work & removing rubbish form site complete all as specified & directed.

Material & Labour for RCC M-20 (Nominal Mix) using 20 mm crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified & directed.

Material & Labour for mild steel deformed TMT bars 8-10mm dia (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Demolition of cement concrete of any description and in any position of WC’s or Bathroom as in sunken portion area above ground floor, removing demolished/ rubbish material completely from site and old waste pipe from sunken portion and cleaning the side/bottom surface of sunken floor with wire brush complete all as specified and directed.

Material & Labour PCC 1:5:10 type E-2 using 40mm graded crushed stone aggregate as in mass filling or filling in two layer in sunken portion of WC or bath complete all as specified and directed.

Material & Labour for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded crushed stone aggregate as in padding levelling etc and roof kerbs mixed with liquid water proofing solution finished even and fair with assuring proper slope as prepatory works to water proofing treatment complete all as specified and directed. Note:-liquid water proofing solution shall be provided in 200ml in 50 Kg of Cement by weight and cost of liquid water proofing solution measured and paid seperately.

Material & Labour for 15mm thick plastering in CM 1:3 along the wall of toilet and bath mixed with 3 % WPC and finished even and smooth without using extra cement complete all as specified and directed.

Material & Labour for bitumen blown 80/100 grade applied hot in two coats to plastered surfaces of any description at the rate of 1.5 kg per sqm per coat complete all as specified and directed.

Material & Labour for Polythene film black 50 micron thick laid in floor complete all as specified and directed.

Material & Labour for 50mm dia GI pipe as in spout to drain out if any leakage of water occures in the sunken portion complete all as specified & directed.

Supply & Fixing in repair chromium plated stainless steel wire basket (storage basket/cup and saucer basket/plate basket/cutlery basket/botlle pull out) pull out type for moduler kitchen of stainless steel grade 304 or food grain including auto closing hinges, telescopic type ball runner, decorative type steel handle & necessary fixing clips/screw complete all as specified and directed.

Taking down carefully existing copper/aluminium point wiring (light, fan, socket or power) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, regulators, sockets, bel push and call bell on wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc with cement plaster, putty and paint to match with the existing surface complete all as specified and directed.

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten complete all as specified and directed.

Taking down unserviceavle Sheet metal box & MCB DB SPN with MCB's of any make/capacity complete all as specified and directed.

M&L for Point wiring with 1.5 Sqmm FRLSH insulated, unsheathed, multi-stranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLSH insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm (OD) concealed in wall/ floor etc including provision of pressed steel terminal box of thickness not less than 1.2mm with earth dolly of suitable size concealed in wall and covered with 3 mm thick phenolic laminated hylam sheet fixed with steel screws for mounting switches, sockets or fan regulators complete all as specified and directed for the following points:-

One light / ceiling fan / exhaust fan / call bell point controlled by one switch

One 6A socket point controlled by one switch on independent board

One 6A socket point controlled by one switch on same board

All as per item No. 160 above but one 16A socket point controlled by one 16A switch on independent board with 2.5 Sqmm copper FRLSH wires & 2.5 Sqmm earth wires controlled by one switch on independent boards complete all as specified and directed.

All as per srl item No. 160 above but with 4 Sq mm FRLSH copper wire with 4 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board complete all as specified and directed.

All as per srl item No. 160 above but with 4 Sq mm FRLSH copper wire with 4 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board but just below / above the existing socket points / DBs up to one meter distance in the same vertical plane complete all as specified and directed.

M&L for point wiring for modular fittings complete with 1.5 Sqmm FRLSH insulated, unsheathed, multi-stranded, 1100 Volts grade copper conductor cable single core conforming to IS:694 along with one run of 1.5 Sqmm FRLSH insulated copper conductor cable green in colour for continuous earthing drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 20mm (OD) concealed in wall/ floor including provision of modular cover plates with frames and 1.5 Sq mm PVC insulated unsheathed stranded copper conductor (FRLSH) cable for common earth and connecting to earth dolly all as specified and directed. Note- Rates of chasing/cutting & making goods shall be included in the unit quoted rates.

One light / ceiling fan / exhaust fan / call bell point controlled by one switch

One 6Amp socket point controlled by one switch on independent board

One 6Amp socket point controlled by one switch on same board

All as per item No 164 above but one 16A socket point controlled by one 16A switch on independent board with 2.5 Sqmm copper FRLSH wires & 2.5 Sqmm earth wires controlled by one switch on independent boards complete all as specified and directed.

All as per item No 164 above but with 4 Sq mm FRLSH copper wire with 4 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board complete all as specified and directed.

All as per item No 164 above but with 4 Sq mm FRLSH copper wire with 4 Sqmm FRLSH copper earth wire for one 16 Amp socket point controlled by one 16 Amp switch on independent board but just below / above the existing socket points / DBs up to one meter distance in the same vertical plane complete all as specified and directed.

Material & Labour for sub main wiring along with earth wire with FRLSH insulated copper conductor, single core cable drawn through and including medium grade rigid PVC conduit conforming to IS:9537 (Pt-III) and its all accessories/junction boxes/ inspection covers etc of suitable size but not less than 25mm concealed in wall/ floor etc of any description complete all as specified and directed for the following sizes:- Note: Three runs of copper cable and one run of PVC conduit shall be measured as one unit length.

2runs x 4 Sqmm (Ph & N) + 1run x 4 Sqmm (earth wire)

2runs x 6 Sqmm (Ph & N) + 1run x 6 Sqmm (earth wire)

2runs x 2.5 Sqmm (Ph & N) + 1run x 2.5 Sqmm (earth wire)

Notes for item No. 168.00 to 168.03 :- (i) Quoted rate shall deemed to include the cost of cutting chases on wall/floor for concealed conduit wiring and making good with cement plaster, putty and paint to match with the existing surface including Three runs of copper cable and one run of PVC conduit shall be measured as one unit length . (ii) If any beam / column / Rock wall is encountered while cutting chases, that particular portion may be provided with PVC casing & capping or surface conduit for drawing cables and surface PVC gang box fully enclosed type for mounting switches, sockets & regulators etc to avoid any damage to the structure. (iii) No cutting shall be done on ceiling for laying PVC conduit for ceiling fan point wiring. Surface conduit or PVC casing capping may be used in that portion.

Supply & Fixing of Switch piano type, single pole, one way 6 Amps 240 volts complete all as specified and directed.

Supply & Fixing of Switch piano type, single pole, one way, 16 Amps 240 volts complete all as specified and directed.

Supply & Fixing of electronic fan regulator in 5 steps, 240Volt 50Hz complete all as specified and directed.

Supply & Fixing of Socket 5 pin, 6 Amp universal type 240 volts complete all as specified and directed.

Supply & Fixing of Socket 6 pin, 6/16 Amp multipurpose 240 volts complete all as specified and directed.

Supply & Fixing of Modular switch 1 way 6Amp 1 module 240Volt 50Hz complete all as specified and directed.

Supply & Fixing of Modular switch 1 way 16Amp 1 module 240Volt 50Hz complete all as specified and directed.

Supply & Fixing of Modular fan regulator step type in 5 steps, 240Volt, 50Hz complete all as specified and directed.

Supply & Fixing of Modular Socket 6Amp, 2/3 pin combined 2 module 240Volt, 50Hz complete all as specified and directed.

Supply & Fixing of Modular Socket 6Amp/16Amp, 2/3 pin combined 2 module 240Volt, 50Hz complete all as specified and directed.

Supply & Fixing of Modular blank plate 1 module complete all as specified and directed.

Supply & Fixing of Lamp holder angle type with metal ring PVC/Polycarbonate body complete all as specified and directed.

Supply & Fixing of Ceiling rose, three terminals, bakelite body, 240 volts, complete all as specified and directed.

Supply & Fixing of integrated LED batten 10 watt, 2 feet long full white in plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5 Sqmm from ceiling rose to connector complete all as specified and directed.

Supply & Fixing of modular MCB protected plug and socket board in sheet steel enclosure with 25Amp rated mini MCB and 20Amp rated 3 pin plug, 240 Volt, 50 Hz complete and making good disturbed surface with cement plaster, putty and paint to match with the existing surface complete all as specified and directed.

Supply & Fixing of integrated LED batten 20 watt, 4 feet long full white in plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5 Sqmm from ceiling rose to connector complete all as specified and directed.

Supply & Fixing of integrated LED batten 20 watt, 4 feet long, twin light (cool white & warm white) in plastic batten with white acrylic cover with built-in electronic driver, pre-wired and connecting up with twisted twin core flexible copper wire of 0.5 Ssqmm from ceiling rose to connector complete all as specified and directed.

Supply & Fixing of LED bulkhead luminaire 10Watt in die-cast aluminium alloy or PVC body heat resistant prismatic glass cover, with specially designed gasket for minimum IP- 55 degree of protection complete all as specified and directed.

Supply & Fixing of LED wall security light fitting 35 watts with high efficiency long life LEDs with In-built electronic driver and surge protection upto 10 Kv complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP-66 degree of protection and provision of 3 core twisted flexible copper cable of size 0.5 Sqmm from ceiling rose to connector complete all as specified and directed.

Supply & Fixing of LED post top lantern light fitting 20watts with high efficiency long life LEDs with In-built electronic driver and surge protection upto 10 Kv and complete housed in pressure die-cast aluminium housing covered with polycarbonate cover with IP-65 degree of protection and provision of 3 core twisted flexible copper cable of size 0.5 Sqmm from ceiling rose to connector complete all as specified and as directed.

Supply & Fixing of sheet metal enclosures 240 volt with suitable rated bus bar for double door IP-43 DB's suitable for one MCB SPN 12 way as incoming and MCB SP as out going complete all as specified and directed. Note: MCBs shall be measured and paid separately.

Supply & Fixing of sheet metal enclosures 240 volt with suitable rated bus bar for double door IP-43 DB's suitable for one MCB SPN 8 way as incoming and MCB SP as out going complete all as specified and directed. Note: MCBs shall be measured and paid separately.

Supply & Fixing of sheet metal enclosures 240 volt with suitable rated bus bar for double door IP-43 DB's suitable for one MCB SPN 4 way as incoming and MCB SP as out going complete all as specified and directed. Note: MCBs shall be measured and paid separately.

Supply & Fixing of MCB 100Amp, 10 KA, TPN, 415 Volt, 50 Hz including taking down existing unserviceable MCB of any description complete all as specified and directed.

Supply & Fixing of MCB 63Amp, 10 KA, TPN, 415 Volt, 50 Hz including taking down existing unserviceable MCB of any description complete all as specified and directed.

Supply & Fixing of MCB 40Amp, 10 KA, SPN, 'C' curve, 240 Volt, 50 Hz including taking down existing unserviceable MCB of any description complete all as specified and directed.

Supply & Fixing of MCB 6 to 32Amp, 10 KA, single Pole, 'C' curve, 240 Volt, 50 Hz including taking down existing unserviceable MCB of any description complete all as specified and directed.

Supply & Fixing cement of call bell ding dong, AC, 240Volt, 50Hz complete all as specified and directed.

Supply & Fixing of Modular Bell Push , flush type, 6Amp, 1 module 50Hz complete all as specified and directed.

Material & Labour for earthing complete with galvanized iron earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to GI wire 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth wire protected by 15mm dia GI pipe medium grade and connected to distribution board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 100mm C/C both ways, GI funnel with watering pipe 20 mm, wire mesh, protection pipe, earth wire up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II.

Taking down Exhaust Fan, sealing cable end, dismantling blades, and removing fan and blades of any description and deposited to E/M yard complete all as specified and directed.

Supply & Fixing of ventilating fan with plastic body (ABS) with louvers 300mm sweep, single phase, 230 volts, 50 Hz Complete all as specified and directed.

Supply and fix of ventilating fan with plastic body with louvers, 250mm sweep, single phase, 230 volts, 50 Hz. Complete all as specified and directed.

M/S Ritu Tandon (BID ID -3199214)