Renovation and repairing the existing staff quarters located at Vamba Keerapalayam in Electricity Department Main office campus to accommodate the Office of Assistant Executive Engineer Town-I and Office of the Junior Engineer Town South O and

Amount

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc complete

Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer

Finishing walls with acrylic smooth exterior paint of required shade - New work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm

Wall painting with acrylic emulsion paint of approved brand and manufacturer to give an even shade - Two or more coats on new work

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq.metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead - with cement mortar 1:4 (1 cement : 4fine sand)

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead - of area 3 sqm and below

Supply and fixing of sliding windows at all levels made out from Unplasticised Poly vinyl chloride frame (UPVC) of natural colour (PRISTINE WHITE) with outer frame of size 40 x 56x40mm / 102 x 56x 40mm and for shutter frame of size 53 x 38 x37 mm for two track / three track sliding widows , with wall thickness of 1.8mm (+/-0.3mm). The section should be single glazing using (flush catch) single point locking. The gasket should be made of EPDM (Ethylene propylene dimonomer) and applying silicon sealents (GE make or wacker make) outside and acrylic sealent inside including single glazing of 5mm thick clear float glass . The sections should be reinforced with GI sheet of 1.5 mm thick with suitable drainage grouting

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part 1) decorative type , core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screw

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI , IS :3564 , embossed on the body , door weight upto 35 kg and door width upto 700 mm ), with necessary accessories and screws etc complete

Providing and fixing aluminium sliding door bolts , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 300 X 16 mm

Providing and fixing aluminium tower bolts , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , with necessary screws etc. complete - 300 x10 mm

Providing and fixing aluminium handles , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 125 mm

Providing and fixing aluminium hanging floor door stopper , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc complete - Twin rubber stopper

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance +_ 1mm ), with wall thickness 2.0 mm (+-0.2mm) , corners of the door frame to be jointed with galvanized brackets and stainless steel screws , joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S.tube of size 19 x 19 mm and 1mm (+-0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification - Extruded section profile size 48 x 40 mm

Providing and fixing to existing door frames - 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59 x 24 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt edging on both sides . The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws . The styles of the shutter reinforced by inserting galvanised M.S.tube of size 20x20 mm and 1mm (+- 0.1mm) wall thickness . The lock rail made up of 'H' section , a uPVC hollow section of size 100 x 24 mm and 2 mm (+-0.2 mm) wall thickness , fixed to the shutter styles by means of plastic / galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness . They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers , complete as per manufacturer's specification (For W.C. and bathroom door shutter)

Providing and fixing of 65 mm Godrej Navatal lock of 7 levers with 3 keys etc complete

Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes - 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - Single tee without door -110x110x110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe

Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs , screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm

Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet , spaced at 1200mm centre to centre and cross "T" of size 24x25mm made of 0.30 mm thick (minimum) sheet , 1200 mm long spaced between main "T" at 600 mm cenetre to centre to form a grid of 1200x600mm and secondary cross "T" of length 600 mm and size 24 x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting / making , opening for services like diffusers , grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27x37x25x1.6mm fixed to ceiling with 12.5mm dia and 50mm long dash fasteners , 4mm GI adjustable rods with galvanised butterfly level clips of size 85x30x0.8mm spaced at 1200mm centre to centre along main T, bottom exposed width of 24 mm of all T - sectons shall be pre-pained with polyester paint, all complete for all heights as per specifications, drawings - GI metal ceiling lay in plain Tegular edge global white color tiles of size 595x595mm,and 0.5mm thick with 8mm drop: made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum) , including factory painted after bending

Providing and laying water proofing for roof portion - Clean the surface using wire brush to remove fungus sticking on the tile surface . Remove the laitance and plaster residues with a chisel & hammer and repair any broken structure with civil work . Apply one coat MACRYL SL (Acrylic penetrating primer) Lay one coat of 3-4 mm thick MATPROOF ACR (Fibre reinforced Acrylic plaster) Elastomeric plaster on the flat area . Provide a seal coat with a flexible MACRYL again

Applying priming coat - with ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Applying priming coat - with ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron / steel works

Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work

Epoxy bonding of new concrete to old concrete

Providing and fixing ASTM pipes including all ASTM plain & brass threaded fittings this included jointing of pipes & fittings with one step ASTM solvent cement , trenching refilling & testing of joints complete (External work) - 32 mm nominal outer dia pipes

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 32mm nominal outer dia pipes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked , with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank - Circular Tank

Providing and fixing ASTM pipes including all ASTM plain& brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes & fitting with one step ASTM solvent cement and testing of joints complete (Internal work exposed on wall ) - 20mm nominal outer dia pipes

Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931- 15 mm nominal bore

Providing and fixing PTMT pillar cock of approved quality and colour - 15 mm nominal bore , 107 mm long, weighing not less than 110 gms

Providing and fixing PTMT Ball cock of approved quality colour and make complete with Epoxy coatd aliminium rod with L.P / H.P.H.D.plastic ball - 40 mm nominal bore, 206 mm long, weighing not less than 690 gms

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32 mm C.P.brass waste of standard pattern , including painting of fittings and brackets ,cutting and making good the walls wherever required - white vitreous china anglet back wash basin size 400x400 mm with single 15mm C.P. brass pillar tap

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required - white glazed fire clay kitchen sink of size 600x450x250mm

Providing and fixing white vitreous china pedestal type water closet (European type W.C.pan) with seat and lid, 10 litre low level white P.V.C. flusing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231,with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required - W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete - semi rigid pipe - 40mm dia

Providing and fixing CP brass health faucet of approved quality - 15 mm nominal bore

Providing and fixing unplasticised PVC connection pipe with brass unions - 45 cm length - 15mm nominal bore

Steel work welded in built up sections /framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required all complete

Surface dressing of the ground including removing vegetation and in - equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50m and lift upto 1.5m - all kinds of soil

Supplying fixing and commisioning of Suguna / Texmo / Sharp 2 HP monoblock pumpset slow speed single phase motor. The rate include the cost of pumpset , pumpset fixing inposition and test run etc.complete

Supplying and fixing of DOL starters 0.5 HP to 5 HP with relay range 0.63 A to 13 A with suitable M.S. angle frame complete.

Supplying and fixing of 1x3x4 sqmm (single run) PVC insulated copper submersible flat flexible cable of Finolex make complete.-upto 10HP pumpset.

Acid cleaning for the existing Mosaic floors , glazed tiles work and removing the stains and decays to give a glassy look etc complte (The Acid used shall be 32% concentrated hydrochloric acid after taking on the precautionary measures)

Chipping the worn out wall and concrete portion using proper tools and removing the loose particles and preparing the surface for treatment with wire brush etc., complete until to reach good surface and removing the debris and disposal of the debris as directed by the Engineer-in-charge with all leads and lifts etc., complete.

Removing the loose particles/rust/mill scale deposits completely duly cleaning it with wire brush/crush sheet etc., and removing the dust over the old concrete surface and providing and system based aromatic Rust remover of CERA/SIKA/ FOSROC/MC Bauchnie/DON/BASE or equivalent make certified and tested by accredited instituions (confirming to IS 9077 - 1979 reffirmed - 1997) Appendix B clause 5.3.3 ) including all tools complete as per manufacturers specification and as directed by the Engineer-in-charge.

Applying a polymer based anticorrosive coating material of CERA / SIKA/FOSROC/ MC Bauchmie/ DON/ BASF or equivalent make certified and testing by accredited institutions mixing mechnically until it is homogenous and applying the same as one rich coat on prepared steel surface with brush with all lead and lift etc., complete and as directed by the Engineer-in-charge. (Measurement as per the total area of treatment)

Plastering the wall surface with cement mortar of mix 1:4 (one part of cement : 4 fine sand) mixed with styrene butadiene styrene rubber latex of CERA/SIKA/FOSROC/MC Bauchmie/DON/BASF or equivalent make certified and tested by accredited institutions (confirming to ASTM 1059-99 for bonding agent, physical properties: Compressive strength 7.5 + or - 2.0MPa, Tensile strength 2.0MPa at the ratio of 1:1.5 (1 part of cera polymer Latex, 1Part of water, 5 parts of cement) in 2 coats including all lead and lift etc., complete as per manufacturer's specifications and as directed by the Engineer-in-charge.

Providing one coat of petro resin based curing compound of CERA/SIKA/ FOSROC/MC Bauchmie/DON/BASF or Equivalent make certified and testing by accedited institutions (confirming to ASTM C309 - 99 & ASTM C15699 (A) over the finishing surface immediately after shuttering of concrete surface or final trowelling of plastered surface with all lead and lift etc., complete and as directed by the Engineer-in-charge.