REPAIRS TO SUNKEN FLOOR TREATMENT, JOINERY, PLUMBING, SANITARY FITTINGS, ROOF TREATMENT, PERIODICAL SERVICES AND CERATAIN CONNECTED MAINTENANCE WORKS IN LAXMI TEK AREA, HARSHAN ENCLAVE, KEY PERSONNEL QUARTERS, QUEENS GARDEN, ETC. UNDER GE I BELGAUM

Amount

Taking down chowkhat with shutters (without taking off shutters from the frame) area not exc 1.5 Sqm each all as specified and directed.

Taking down chowkhat with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n exc 4 Sqm each all as specified and directed.

Taking down shutters of any description n exc 1sqm each all as specified and directed.

Taking down shutters of any description area exc 1 sqm and n.exc 2 sqm each all as specified and directed.

Taking down shutters of any description not exc 1sqm each and refixing in the same opening all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6, type C1, using 20 mm graded stone aggregate and setting in CM 1:6 including demolition of existing unserviceable PCC block masonry built in cement mortar in any position below or above ground level and making good disturbed surfaces all as specified and directed.

M&L plain cement concrete 1:2:4, type B0, using 12.5mm graded stone aggregate as in roof kerbs, mud stops, coving, etc. with rounded or chamfered edges including demolition of existing plain cement concrete of any description and size and making good disturbed surfaces all as specified and directed

M&L plain cement concrete 1:3:6, type C-1, using 20mm graded stone aggregate as in coping, bed blocks, eves filling between wall and tile/ sheet roofing including necessary form work and scaffolding work upto 2nd floor of buildings including demolition of existing plain cement concrete coping, bed blocks, eves filling of any description and size and making good disturbed surfaces all as specified and directed

Supply only integral water proofing compound all as specified and as directed.

M&L for 2nd class hard wood chowkhat or frames, plain, solid, wrought, framed and rebated on the solid rounded or chamfered, put together with glue pinned at joints, fixed in position all as specified and directed.

M&L for 35 mm thick second class hard wood, Plain framed, panelled shutter (two panel) with lock rail and panel of 12mm thick plywood BWR 7 ply with commercial veneers on both faces with size of rails and stiles sizes of members of shutters as specified in SSR Part I, Section 8. Clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for 35mm thick 2nd class hard wood glazed/ gauged shutters, open rebated and prepared to receive glass, gauze, etc. (divided into square with plain, chamfered or rounded, mitred and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a) and fitted to chowkats all as specified and as directed.

M&L for 30mm thick 2nd class hard wood glazed/ gauged window/ ventilator shutters, open rebated and prepared to receive glass, gauze, etc. (divided into square with plain, chamfered or rounded, mitred and rebated sash bars any numbers), edge of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (b) and fitted to chowkats all as specified and as directed.

S&F 30mm thick flush shutters, solid core construction, with block board core with decorative face veneers on one face and commercial type plywood face other face and covered with suitable teak wood lipping, fitted to chowkats all as specified and as directed.

M&L for 18/19mm thick veneered particle board, interior grade, solid core, general purpose type, with face veneers of type BB fixed with screw to timber frame work including external teak wood lipping 6mm thick around edges including taking down existing unserviceable boards of any description and thickness and making good disturbed surfaces all as specified and as directed.

M&L for solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelaminated PVC sheet on both sides reinforced with M.S. Square tube, supplying and fixing in opening as per specification and drawing all as specified and as directed.

M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelaminated PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of prelaminated PVC sheets on both sides to be fitted in the M.S. frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing all as specified and directed

S&F Steel windows with side hung shutters including projecting type hinges with steel handle and steel tower bolt, hold fasts, complete with glazing bars, dovetailed or welded including taking down existing steel windows of any description all as specified and as directed.

S&F MS butt hinges 100mm in size, medium weight, cold rolled all as specified and directed.

S&F in repairs MS butt hinges 100mm in size, medium weight, cold rolled all as specified and directed.

S&F MS butt hinges 75mm in size, medium weight, cold rolled all as specified and directed.

S&F in repairs continuous (piano) hinges, mild steel, bright finish or electro galvanised with width of flaps when open 30mm all as specified and as directed.

S&F 300mm long mild steel helical door spring, ordinary rat tail pattern spring, including roller and roller plate complete all as specified and as directed.

S&F aluminium anodised barrel tower bolt of extruded section, 150mm long all as specified and directed.

S&F aluminium anodised barrel tower bolt of extruded section, 100mm long all as specified and directed.

S&F in repairs aluminium anodised barrel tower bolt of extruded section, 100mm long all as specified and directed.

S&F 100 mm long extruded section aluminium alloy anodised handles fabricated type all as specified and directed.

S&F aluminium handle, 'D' type, anodised 150 mm in size all as specified and directed.

S&F in repairs aluminium handle, 'D' type, anodised 100 mm in size all as specified and directed.

S&F 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F in repairs 300mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts plate type with bright bolt not less than 12mm dia all as specified and directed.

S&F in repairs Mortice lock, brass, vertical type, 4 levers, size 100 mm, all as specified and directed. Make: GODREJ or equivalent approved make.

S&F in repairs mild steel cup board knobs, bright polished, 40mm dia fixed with mild steel nut and screw and washers all as specified and directed.

S&F in repairs 100mm long mild steel hasp and staple, wire type, stove enamelled black including bolt to hinge plate fixed with screws complete all as specified and as directed.

S&F in repairs floor door stopper of aluminium body and tongue, anodised, with 150mm long cover plate and hard drawn steel spring, fixed in floor all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40mm fixed in panel of joinery with stainless steel wire staples all as specified and directed.

M&L for mild steel small articles like bands, straps, including bolts, if required; hooks (stay), hook and pintle hinges; large hasps and staples; hand made sliding bolts; clamps; hold fasts; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar articles conforming to Fe-290 Gde-E-165, fixed in repairs, all as specified and as directed.

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165, fixed in repairs, all as specified and as directed.

S&F mild steel works in tubular trusses, rafters, purlins, etc. including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240, fixed in repairs, all as specified and as directed.

Repairs to loose hanging mild steel window/ ventilator shutters not exceeding 1sqm each including repairs to hardwares by welding for smooth functioning of the shutters including making good the welded surfaces to match with the existing window/ ventilator surface all as specified and as directed. Notes: (i) Windows are to be fixed to the buildings upto 3 stories height. (ii) Hardwares wherever required to be replaced shall be measured and paid separately under respective items of this Schedule at supply only rates.

Supply only mild steel box type hinges, suitable for steel windows all as specified and as directed.

M&L for Mild steel handles, suitable for steel windows, fixed with necessary nut, bolt and washers, fixed in repairs all as specified and as directed.

M&L for Mild steel peg stays, 300mm long, suitable for steel windows, fixed with necessary nut, bolt and washers, fixed in repairs all as specified and as directed.

S&F in repairs Mild steel powder coated curtain rods, fancy type, 25mm dia including brackets and end designer caps all as specified and as directed.

S&F in repairs fancy type brackets, mild steel with antique finish or colour with rounded fancy ends suitable for holding 25mm dia single curtain rods, fixed to wall with necessary screws including drilling and plugging the holding screws and making good the wall surfaces all as specified and directed. Make: MARVEL or equivalent

S&F in repairs fancy type brackets, mild steel with antique finish or colour with rounded fancy ends as in middle supports for holding 25mm dia single curtain rods, fixed to wall with necessary screws including drilling and plugging the holding screws and making good the wall surfaces all as specified and directed. Make: MARVEL or equivalent

M&L for removal of existing vegetations/ trees not exceeding 30cm girth on in-accessible roof of buildings including digging out roots, pouring sulphuric acid, making good disturbed portions with cement mortar 1:3 and provision of two coats of sola reflective aluminium paint including necessary preparation of surfaces all as specified and as directed.

M&L for providing roof treatment with APP modified water proofing membrane with the following specifications all as specified and directed.

Removing existing roof/ chajjas treatment of any type like plastic felt/ HP tiles of any description including taking down existing plastering/ concrete of any thickness and cleaning the top surface of RCC slab with wire brush including removal of debris to a distance exc 50m but n exc 100m

Brushing with neat cement slurry @ 3Kg/Sqm on cleaned RCC slab surfaces and rendering 10 mm thick in CM 1:3 mixed with water proofing compound and finishing surfaces even and smooth without using extra cement. Note: Water proofing compound shall be measured and paid separately

Preparation of plastered surfaces by removing dust, dirt & applying oil bound bituminous primer at 0.3 litre per Sqm & providing APP modified water proofing membrane 4mm thick and weight not less than 4.5kg/Sqm reinforced with non oven polyester mat weight not less than 160gms per Sqm including min 10cm side/over lap & including applying a coat of blown hot bitumen grade 85/25 over membrane at 1.2kg per Sqm & on drying apply a coat of solar reflective bituminous aluminium paint at 0.1kg/sqm.

NOTE: APP modified water proofing membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given IS 16540-2017/ IS 16532-2017. Contractor shall produce necessary test certificate of the manufacturer to the Engineer-in-charge before incorporation in the work. Necessary independent tests shall also be carried out by the contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work.

M&L for providing water proof treatment to RCC roof with acylic polymer heavy duty fibre reinforced coating with the following specifications all as specified and directed.

The RCC roof surface shall be prepared and made free from all dust, loose particles, laitance and sharp edges, fungus, algae, organic matters, etc. including removal of debris outside of MOD premises

All cracks shall be repaired by cutting 'V' groove along the longitudinal section of cracks and filling with polymer modified mortar admixed with Dr. Fixit Pidicrete URP or equivalent at the ratio of 1:5:15 (URP : Cement :Sand respectively)

All potholes and uneven surfaces shall be repaired with polymer modified mortar over a bonding coat of Dr. Fixit Pidicrete URP or equivalent at the ratio of 1:1 (URP : Cement respectively)

Over the prepared surfaces one priming/ efflorescent coat of Dr. Fixit Primeseal or equivalent shall be applied by diluting the primeseal with water at the ratio of 2:1 (Primer: Water respectively)

Over the primered surfaces water proof coating shall be applied with acylic polymer heavy duty fibre reinforced coating of Dr. Fixit New Coat or equivalent consisting of three coats of application to form 1mm thick heavy duty water proofing coating.

NOTE: Water proofing chemicals shall be procured from approved manufacturer with prior written approval of GE. Full quantitiy of fresh chemicals required for incorporating in the work shall be brought to site with sealed containers. Water proofing treatment shall be carried out through authorised applicator of the manufacturer and the contractor shall produce necessary certificate of authentication to the Engineer-in-charge before commence of the work.

M&L for providing sunken floor treatment with APP modified water proofing membrane with the following specifications all as specified and directed.

Removing existing floor treatment of any type and any description including taking down existing plastering of any thickness and cleaning the top surface of RCC slab with wire brush including removal of debris to a distance exc 50m but n exc 100m

Brushing with neat cement slurry @ 3Kg/Sqm on cleaned RCC slab surfaces and rendering 10 mm thick in CM 1:3 mixed with water proofing compound and finishing surfaces even and smooth without using extra cement. Note: Water proofing compound shall be measured and paid separately

Preparation of plastered surfaces by removing dust, dirt & applying oil bound bituminous primer at 0.3 litre per Sqm & providing APP modified water proofing membrane 4mm thick and weight not less than 4.5kg/Sqm reinforced with non oven polyester mat weight not less than 160gms per Sqm including min 10cm side/over lap & including applying a coat of blown hot bitumen grade 85/25 at 1.2kg per Sqm or cold application of bituminous elastomeric coat at 0.70 kg/ sqm

NOTE: APP modified water proofing membrane shall be of any one of the approved makes as specified here-in-after and shall conform to specifications given IS 16540-2017/ IS 16532-2017. Contractor shall produce necessary test certificate of the manufacturer to the Engineer-in-charge before incorporation in the work. Necessary independent tests shall also be carried out by the contractor without any extra cost to the Deptt as per relevant IS specifications and membranes with satisfactory test results shall only be incorporated in the work.

S&F 4mm thick High Pressure Steam Cured (HPSC) non asbestos fibre cement building board in false ceiling with aluminium anodized snap grids of 60x60cm with Tee section 35x25x1.25mm, angle section 25x25x1.25mm thick including 2mm dia GI hanging wire including all hanger fittings etc and applying three coats of white wash on ceiling including dismantling of existing unserviceable false ceiling boards of any description and size alongwith snap grid frame works including making good disturbed wall/ ceiling surfaces all as specified and directed.

M&L for plain cement concrete 1:5:10, type E2, using 40mm graded stone aggregate as in filling under sunken floors all as specified and directed.

M&L for 100 mm thick plain cement concrete 1:2:4 type B2 using 40mm graded stone aggregate as in paving, hard standing etc. and finishing the concrete surface even and fair without using extra cement and making impressions of expanded metal while the concrete is green all as specified and directed.

M&L for non skid coloured ceramic tiles, 7mm thick, area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in floor, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:4 including dismantling of existing unserviceable tiling alongwith cement mortar bedding (but not backing) and removing rubbish off the premises all as specified and directed.

M&L for coloured glazed ceramic tiles 450mm x 300mm x 7 mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 including dismantling of existing unserviceable tiling alongwith cement mortar plaster and removing rubbish off the premises all as specified and directed.

M&L for coloured vitrified tiles, square or rectangular, light shade, 9 to 10mm thick, area of each tile not exc 0.36 Sqm, as in floors/ skirtings, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigments to match the shade of the tile laid over and including 15mm thick screed bed in cement mortar 1:6 including dismantling of existing unserviceable tiling alongwith cement mortar bedding (but not backing) and removing rubbish off the premises all as specified and directed.

M&L for coloured vitrified tiles, light shade, size of tile to match with the floor tiles, 9 to 10mm thick on vertical surfaces such as skirting, dados etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces including 10mm thick backing coat in CM 1:4 including dismantling of existing unserviceable tiling alongwith cement mortar plaster and removing rubbish off the premises all as specified and directed.

M&L for chequered cement concrete tiles 30cm x 30cm x 25mm thick, with grey cement and pigments, set jointed and pointed in neat cement slurry, laid over and including 15mm thick screed bed in cement mortar 1:6 as in pathways, etc. complete including dismantling of existing unserviceable tiling alongwith cement mortar bedding (but not backing) and removing rubbish off the premises all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in flooring, laid and jointed with neat slurry and pointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 15mm thick screed bed in cement mortar 1:4 including dismantling of existing unserviceable stone tiles alongwith cement mortar bedding and removing rubbish off the premises all as specified and directed.

M&L for machine cut Kota stone slab, 20-25mm thick, as in risers of steps, skirting, dado, cladding to pillars, etc., laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including bull nosing the edges, rubbing and polishing complete including 10mm thick backing coat in CM 1:4 including dismantling of existing unserviceable stone tiles alongwith cement mortar plaster and removing rubbish off the premises all as specified and directed.

M&L for plain cement concrete 1:3:6, type C2, using 40 mm graded stone aggregate, 75mm thick as in plinth protection, finishing the surface fair and even, in panels & filling joints with mortar, etc. including demolition of existing plain cement concrete plinth protection of any description and size and making good disturbed surfaces all as specified and directed

M&L for weather proof coating to external wall surfaces with Rain coat with the following specifications all as specified and directed.

The external wall surfaces shall be prepared and made free from all dust, loose particles, laitance and sharp edges, fungus, algae, organic matters, etc. including removal of debris outside of MOD premises

All wide shrinkage cracks shall be cut open and Dr. Fixit crack X paste (for cracks upto 5mm)/ Dr. Fixit crack shrink free paste (for cracks upto 10mm) or equivalent shall be filled in the cracks and finished.

All masonry wall & RCC column separation/ masonry wall & RCC beam separation shall be filled with polymer modified mortar admixed with Dr. Fixit URP or equivalent at the ratio of 1:3 with polymer dosage of 12-20%.

Over the prepared surfaces one primer coat of Dr. Fixit Primeseal acrylic water based penetrating primer or equivalent shall be applied as a bonding coat.

Over the primered surfaces water proof coating shall be applied with two coats of Dr. Fixit Rain Coat or equivalent to form weather proof and decorative coating with 80-100 micron thick and 100% elongation properties.

NOTE: Water proofing chemicals shall be procured from approved manufacturer with prior written approval of GE. Full quantitiy of fresh chemicals required for incorporating in the work shall be brought to site with sealed containers. Water proofing treatment shall be carried out through authorised applicator of the manufacturer and the contractor shall produce necessary certificate of authentication to the Engineer-in-charge before commence of the work.

M&L for rendering 5mm thick in cement mortar 1:3 on soffit of roof ceiling, finished fair and even without using extra cement including taking down existing cement plaster and hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or block masonry or concrete surfaces finished even and smooth without using extra cement complete all as directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or PCC block masonry or concrete surfaces finished even and smooth without using extra cement including taking down existing cement plaster and hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

M&L for rendering 5mm thick in cement mortar 1:4 mixed with water proofing compound over 10mm thick backing coat in cement mortar 1:6 on fair faces of brick work or PCC block masonry surfaces finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

M&L for rendering 5mm thick in cement mortar 1:4 mixed with approved water proofing compound over a coat of 10mm thick backing coat in cement mortar 1:6 on other than fair faces of brick work or stone masonry surfaces finished even and smooth without using extra cement including taking down existing cement plaster and hacking for key, scrubbing down with water, etc. complete all as specified and as directed. Note: Water proofing compound shall be measured and paid separately.

M&L for one coat of white wash on old decorated surfaces of ceilings including necessary preparation of surfaces all as specified and as directed.

M&L for one coat of white wash on old decorated surfaces of walls, pillasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for three coats of white wash on newly plastered surfaces of ceilings including necessary preparation of surfaces all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable) on newly plastered surfaces of walls, cornices, pillasters, etc. including necessary preparation of surfaces with chalk whiting primer all as specified and directed.

M&L for one coat of oil bound distemper (Acrylic distemper washable), any colour, on old distempered walls, pillasters, cornices, etc., including necessary preparation of surfaces by washing, rubbing down and stopping all as specified and as directed.

M&L for two coats of oil bound distemper (Acrylic distemper washable) over a coat of primer over 1mm thick layer of wall care putty, on walls, pillasters, cornices, etc., including complete removal of existing treatment and necessary preparation of surfaces all as specified and as directed.

M&L for two coats of cement based paint, any colour, on newly plastered surfaces of walls, pilasters, cornices, etc., over a coat of alkali resistant primer including necessary preparation of surfaces all as specified and directed.

M&L for one coat of cement based paint on old cement painted walls, pillasters, cornices, etc., including necessary preparation of surfaces all as specified and as directed.

M&L for one coat of weather proof exterior emulsion on old decorated surfaces of walls, pillasters, roof projections, facias, drops, chajjas, etc., including necessary preparation of surfaces by washing, rubbing down and stopping all as specified and as directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed.

M&L for one coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed.

M&L for preparation of new steel surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

M&L for one coat of synthetic enamel paint on old painted steel surfaces of any description over 10cm width or girth including necessary preparation of surfaces all as specified and as directed.

S&F 16mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors including taking up or down existing unserviceable PVC/ GI tubes of any grade and making good disturbed surfaces all as specified and directed.

S&F 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors including taking up or down existing unserviceable PVC/ GI tubes of any grade and making good disturbed surfaces all as specified and directed.

S&F 25mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings, fixed complete to walls, ceilings or laid in floors including taking up or down existing unserviceable PVC/ GI tubes of any grade and making good disturbed surfaces all as specified and directed.

S&F in repairs 15 mm bore Bib tap, brass chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F in repairs 15 mm bore Bib tap, long body, brass chromium plated, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

S&F in repairs 3 way mixer tap for mixing hot and cold water, fancy type, brass chromium plated screwed down for 15mm bore GI pipe all as specified and directed.

S&F in repairs 15mm bore PTMT bib taps, standard type, (Minimum weight 90gms) any colour, high pressure screwed for iron pipe all as specified and as directed.

S&F health faucet, brass chromium plated with 1m long flexible PVC tube and wall hook all as specified and as directed. Make: Cat No. 563 of JAQUAR or equivalent model in JOHNSON/ CERA

S&F in repairs 15mm bore stop valves, cast copper alloy screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repairs 15mm bore stop valves, fancy type, brass chromium plated, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repairs 15mm bore stop valves, fancy type brass CP, with long shank and cup (concealed type), screwed down high pressure, screwed both ends for iron pipe for unions all as specified and as directed.

S&F in repairs pillar taps, brass chromium plated with capstan heads, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed.

S&F in repairs pillar taps, fancy type, brass chromium plated , with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed down high pressure screwed for 15mm bore GI pipe all as specified and directed. Make: Cat No. 011 of JAQUAR or equivalent

S&F in repairs 15mm bore PTMT pillar taps, standard type, (Minimum weight 110gms) any colour, high pressure screwed for iron pipe all as specified and as directed.

S&F in repairs PVC connection 15mm size with PTMT nuts, 450mm long all as specified and directed.

S&F in repairs PVC connection 15mm size with PTMT nuts, 750mm long all as specified and directed.

S&F in repairs Vitreous China wash basin, white, flat back, size 450x300mm, excluding taps, waste chain and plug and porcelain stopper but including brackets etc complete all as specified and directed.

S&F in repairs Vitreous China urinal, Half stall type, white, with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) all as specified and as directed.

S&F in repairs vitreous china squatting pan, Orissa pattern of size 580 x 440 mm, white, with integral foot rest (excluding flushing cistern) including 'P' or 'S' trap etc complete all as specified and directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, including 'P' or 'S' trap, plastic water closet seat of any colour as approved by GE, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device, fixing bolts etc, connecting to drain pipe and flushing pipe including provision of PVC flush pipe complete all as specified and as directed.

S&F in repairs plastic water closet seat of any colour as approved by GE, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device all as specified and as directed.

S&F in repairs syphonic action type low level PVC flushing cistern, 10 litres capacity, white, with inlet, ball valve, float, handle and flush pipe etc complete all as specified and directed.

S&F in repair 1mm thick stainless steel sink, overall size 495x420mm, bowl size 410x330x160mm, with plug, washers & wastes incl bedding in cement mortar, fixing cantilever brackets & connecting union to pipe all as specified and as directed.

S&F in repairs brass chromium plated towel rail 600mm long with and including Chromium plated brass screws & wooden/ plastic cleats all as specified and as directed.

S&F in repairs PTMT swivel shower rose, minimum weight 40gms, any colour for fixing with 15mm bore GI pipe, any colour all as specified and as directed.

S&F in repairs 32mm size Waste fittings, brass, chromium plated suitable for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

S&F in repairs PTMT waste couplings, half or full threaded, minimum weight 45 gms suitable for 32mm bore discharge pipes all as specified and directed.

S&F in repairs PVC flexible pipe (waste pipe), 900mm long, suitable for 32 mm bore waste coupling of sink/ wash hand basin all as specified and directed.

M&L for 50mm bore Ligh Density Polyethylene pipes (LDPE) of pressure rating 4 kgf/cm2 etc.fixed complete to walls, ceilings or laid in floors, fixed in repairs, all as specified and as directed.

S&F in repairs 110mm bore UPVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls all as specified and directed.

S&F in repairs 75mm bore UPVC (SWR) pipes, single socketed, in any length with rubber ring joints fixed to walls all as specified and directed.

S&F in repairs 110mm bore UPVC (SWR) bends any radius all as specified and directed.

S&F in repairs 75mm bore UPVC (SWR) bends any radius all as specified and directed.

S&F in repairs 110mm bore UPVC (SWR) branch piece, single (single Y) equal or unequal with access door all as specified and directed.

S&F in repairs 75mm bore UPVC (SWR) branch piece, single (single Y) equal or unequal with access door all as specified and directed.

S & F in repairs 110mm bore PVC (SWR) branch piece, double (double Y) equal or unequal with access door all as specified and directed.

S&F in repairs 110mm bore UPVC (SWR) vent cowl all as specified and directed.

S&F in repairs UPVC (SWR) floor trap plain with grating including jointing with solvent cement 63mm dia outlet all as specified and directed.

S&F in repairs UPVC (SWR) floor trap plain with grating including jointing with solvent cement 75mm dia outlet all as specified and directed.

S&F in repairs 100mm dis stainless steel grating with stainless steel frame, with or without hole for waste pipe connection, all as specified and as directed.

S&F in repairs UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed.

M/s A N Kalbhavi

M/s. VIJAY ELECTRICALS

M/S VISHWAROOP ELECTRONICS AND ELECTRICALS

M/s. KIRAN M CHOUGULE

SHRI.H.R.PATIL