REPAIR, POLISHING AND PAINTING OF ALMIRAH STEEL, TABLE OF VARIOUS FURNITURES FOR OTM ACCN AT BSO PANAGARH UNDER GE PANAGARH

Amount

FD-1031 Almirah steel large

(a) Taking out of broken door shutter from Almirah Large Steel and re-fixing the same existing door shutters in original position with pin type new steel hinges of existing size duly welded as required including denting . All as directed by Engineer-in-Charge and shown on drawing

(b) Removing the worn out u/s handle from the almirah and providing/fixing of new handle chromium plated heavy duty as approved by Engr-in-Charge/GE.

(c) Removing the worn out u/s lock from almirah and providing/fixing with new lock 6 lever with deuplicate key ISI marked with round shape of MS key plate as approved by Engr-in-Charge/GE duly fixed as per drawing.

(d) Removing the worn out u/s 3 way locking device and providing/fixing the new one in its original postion as per drg.

(e) Removing the worn out u/s leg and providing / fixing the new leg made out of MS sheet 1.00mm thick in its original position duly welded as per drg.

(f) Taking out of u/s worn out shelf and providing the new one of existing size and shape made out of MS sheet 1.00mm thick. All as shown on drg.

(g) Removing the worn out paint from internal/external surface of almirah steel large by scraping. Necessary preparation of surface for painting duly dented/pitted and smoothen the surface by putty and painting the internal and external surface with two coat of synthetic enemalled paint over a coat of primer Metal to bring the surface to a glossy shine as directed by Engr-in-Charge.

FD-67(M)/ 1032 Almirah Steel Medium

(a) All as per item No 1.01 here-in-before but for almirah steel medium.

(b) All as per item No 1.02 here-in-before but for almirah steel medium.

(c) All as per item No 1.03 here-in-before but for almirah steel medium.

(d) All as per item No 1.04 here-in-before but for almirah steel medium.

(e) All as per item No 1.05 here-in-before but for almirah steel medium.

(f) All as per item No 1.06 here-in-before but for almirah steel medium.

(g) All as per item No 1.07 here-in-before but for almirah steel medium.

DB-4124 Chair CBA Office

(a) Remove of existing unserviceable under mentioned members and providing the new one made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg. .

(i) Front leg.

(ii) Rear leg.

(iii) Side rail (Hole should be 12.5mm apart from each other).

(iv) Front rail (Hole should be 12.5mm apart from each other).

(v) Back rail (Hole should be 12.5mm apart from each other).

(vi) Back rest batten horizontal

(vii) Long stiffener(Lower)

(viii) Short stiffener(Lower).

(b) Removing the all worn out plastic cane from chair and providing and re-caning of the same with new white plastic cane 2mm thick half round oval shape for general weaving and 4mm thick cane plastic for beading work all around as shown in drg (Plastic Cane Type -I HDPE)

(c) Preparation of surface by Remove of existing polishing mark scratches from all exposed wooden surface to make clean and smooth with required grade of sand paper and finish with polish to bring the surface to require glossy finish and as directed by Engr-in-Charge. .

FD-229/17(M) Repair/Re-canning of chair Easy Remove of existing unserviceable under mentioned members and providing the new one made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

(a) Front Legs

(b) Front rail of seat frame (Hole should be 12.5mm apart of each other)

(c) Side Rail(Ditto complete)

(d) Back Rail(Ditto complete)

(e) Arm Rest

(f) Remove the existing unserviceable canning and supply and weave with 2 mm thick new white plastic cane oval shape Godrej pattern and beading with 4mm thick new white plastic cane make Ajay /premier as approval by GE and providing new hard rubber shoes on legs below of chair Easy.

(g) All as per item No 3.11 here-in-before but for Chair easy.

FD-75(M) Chair CB Steel With Arm

(a) Removing the worn out paint by scraping from the steel surface, necessary preparation of surface for painting and welding wherever required, two coat of spray painting with synthetic enamelled paint olive green over a coat of Metal primer after dent/bent portion. Wooden surface should be black polish to required glazed and shine.

(b) Removing the worn out u/s seat frame and providing/fixing the new one of existing size made out of 1st class teak wood duly re-caning with new plastic cane 2mm thick oval shape for general weaving and 4mm thick plastic cane for beading all around as show in drg. Wooden frame should be finished with black polish and fix in its original position with required screw(plastic cane type-I HDPE).

(c) All as per item 5.02 here-in-before but back frame.

(d) Removing the worn out u/s handle made out of H.W(T.W) well seasoned and providing/fixing of exisiting size and shape with required screw after finish with black polish.

FD-75(M) Chair CB Steel Without Arm

(a) All as per item 5.01 here-in-before but for chair CB steel without arm

(b) All as per item 5.02 here-in-before but for chair CB steel without arm

(c) All as per item 5.03 here-in-before but for chair CB steel without arm

FD-277 Repair to Peg Table

(a) Remove the old unserviceable leg and providing the new leg made out of 1st class teak Wood seasoned of size 30x50x362mm high and fixing the same in its original position as per drg.

(b) Remove old broken top rail and providing the new top rail made out of 1st class hardwood teak of size 20mm x 40mm x380mm and fixing the same in its original position as per drg.

(c) Remove the old top and providing the new top made out of 18mm particle board one side laminated exterior grade with 4mm teak wood beading all around and fixing the same on peg table in its original position as per drawing and providing new hard rubber/PVC/Nylon shoes to the bottom of legs. Size of particle board shall be 450mm x 300 mm.

(d) All as per item No 3.11 here-in-before but for peg table.

FD/MAP/II/04 Repair of Chair Dinning

(a) Remove the existing unserviceable/broken 12mm ply seat from chair dinning and supply & fixing the new 12mm ply seat 4mm existing size in its original position all as shown on drg and directed by Engr-in-Charge.

(b) Remove of existing unserviceable under mentioned members and providing the new one made out of 1st class HW well seasoned (Teak) and fixing the same in its original position as per drg.

(i) Front Legs

(ii) Rear Legs

(iii) Front rail of seat frame

(iv) Side Rail

(v) Back Rail

(vi) Short stiffener (390x390cm)

(vii) 75mm thick 32 density cushion (Kurlon)

(viii) Back rest batten

(ix) All as per item No 3.11 here-in-before but for Chair Dining

FD-257, FD-1029 Locker Steel

(a) Taking out of broken door shutter from Locker Steel and re-fixing the same existing door shutters in original position with pin type new steel hinges of existing size duly welded as required including denting . All as directed by Engineer-in-Charge and shown on drawing

(b) Removing old broken damaged hasp of locker steel and S/F new hasp & stappples of size 150 mm long chromium plated to the shutters of locker steel.

(c) Removing old broken handle of locker steel and S/F new handle of size 100 mm long 'D' Type chromium plated to the shutters of locker steel.

(d) Removing old broken hanging rod of locker steel and S/F new hanging rod made out of 20mm dia chromium plated pipe 500mm long of locker steel.

(e) All as per item No 1.07 but for Locker Steel.

FD- 1003 Table office officer steel (FD-1003)

(a) Removing old broken damaged top of table office officer steel and S/F new top made out of 18/19mm thick prelaminated particle board one side teak veneered with standard PVC edging all around the top.

(b) Removing old u/s internal drawer locks from table office officer steel and S/F new internal drawer locks 40mm 4 lever with duplicate keys of approved quality.

(b) Taking out of u/s worn out drawer and providing the new one of existing size and shape made out of MS sheet 1.00mm thick. All as shown on drg.

(b) Taking out of u/s worn out drawer-shutter and providing the new one of existing size and shape made out of MS sheet 1.00mm thick. All as shown on drg.

(c) Repair of Drawer and worn out welding in drawer in its original position existing size and shape. All as shown on drg.

( c) Removing old broken u/s hard rubber shoes of table office officer steel and S/F new hard rubber shoes of approved quality & tightly fitted at the bottom of legs of table office officer steel complete all as specified and shown on drawing.

(d) All as per item No 1.07 but for table office officer Steel.

FD-84/1004 Table office clerk steel

(a) Removing old broken damaged top of table office clerk steel and S/F new top made out of 18/19mm thick prelaminated particle board one side teak veneered with 19x4mm teak wood beading duly french polished all around the top.

( b) Removing old u/s internal cupboard/drawer locks from table office clerk steel and S/F new internal locks 40mm 4 lever with duplicate keys of approved quality.

(b) Taking out of u/s worn out drawer and providing the new one of existing size and shape made out of MS sheet 1.00mm thick. All as shown on drg.

(c) Repair of Drawer and worn out welding in drayer in its original position existing size and shape. All as shown on drg.

(e) Removing old broken u/s rubber shoes of table office clerk steel and S/F new hard rubber shoes of approved quality & tightly fitted at the bottom of legs of table office clerk steel

(f) All as per item No 1.07 but for table office clerk Steel.

FD-19 (M) / 56 Repair/Re-canning of Chair Varandah

(a) Remove of old caning from the steel frame of chair varandah and making the frame by means of welding wherever required to bring its in original shape as per drg.

( b) Removing old broken u/s hard rubber shoes of chair varandah and S/F new hard rubber shoes of approved quality & tightly fitted at the bottom of legs of chair varandah complete all as specified and shown on drawing.

(c) De-rusting/cleaning the iron frame to smooth surface and painting all steel surface with two coat of synthetic enameled white paint over a coat of red oxide primer to bring the surface with glossy finish and re-caning the same with 4mm white plastic cane Make-Ajoy/Primer oval shape as approved by Garrison Engineer as per drg and providing the new rubber shoe complete.

FD/MAP-II/01 Charpoy Hrad Top MAP

(a) Remove the existing unserviceable Ply wood from Charpoy ip sq with ply and making the frame to its original position by tightening etc and Supply & fixing with new ply wood 12mm thick, commercial, BWR Grade (IS-303) of existing shape & size and as directed by Engr-in-Charge.

All as per item No 1.07 here-in-before but for Charpoy Hard Top MAP

TP Locker Steel/ Cabinet (3000x1200x800mm)

(a) Taking out of broken door shutter from Locker Steel Cabinet and re-fixing the same existing door shutters in original position with pin type new steel hinges of existing size duly welded as required including denting . All as directed by Engineer-in-Charge and shown on drawing

(b) Taking out of u/s worn out drawer and providing the new one of existing size and shape made out of MS sheet 1.00mm thick. All as shown on drg.

(c) Removing old broken damaged hasp & stapples of locker steel and S/F new hasp & stappples of size 150 mm long chromium plated to the shutters of locker steel.

(b) Removing old broken handle of locker steel and S/F new handle of size 100 mm long 'D' Type chromium plated to the shutters of locker steel.

(e) Removing old broken hanging rod of locker steel and S/F new hanging rod made out of 20mm dia chromium plated pipe 500mm long of locker steel.

(f) All as per item No 1.07 but for Locker Steel.

FD-165(M) Table dining ORs

(a) Removing old broken damaged top of table dining OR and S/F new top made out of 18/19mm thick prelaminated particle board one side teak veneered phenol formal dehyde exterior grade with 19x4mm teakwood beading fixed with headless nails all around the top. Top will be covered with Almn sheet 20 gauge.

(b) Removing the existing steel long rail from Table Dining ORs and S & F new steel long rail of size : 25mm x 25mm x 1.6mm thick, 1575mm long. All as shown on drg and directed by Engineer-in-Charge.

(c) Remove the existing MS legs from Table Dining ORs and S & F new leg made out of 25mm x 25mm x MS tube 1.6mm well thickness. All as directed by Engineer-in-Charge and as shown on drg.

(d) Remove the existing stiffner bottom and S & F new stiffner bottom made out of 25mm x 25mm, MS tube of 1.6mm well thickness. All as directed by Engineer-in-Charge and shown on drg.

(e) Remove the existing stiffner Top and S & F new stiffner top made out of 25mm x 25mm, MS tube of 1.6mm well thickness. All as directed by Engineer-in-Charge and shown on drg.

(f) Remove the existing unserviceable shoes from Table Dining OR's and and S & F new PVC Shoes suitable for 25x2mm MS tube. All as directed by Engineer-in-Charge and shown on drg.

(g) Painting (Remove the existing worn out paint from Table Dining OR's and applying one coat of synthetic enamell paint black over a coat of primer. All as directed by Engineer-in-Charge and shown on drg.

FD/MAP-II/03 Table dining 6 Pers (MAP )

All as per item No11.01 here-in-before but for Table dining 6 Pers

Removing old & u/s legs of table dinning 6 pers & S/F new legs of size 750x45x90mm made out of 1st class well seasoned teakwood duly fixing PVC rubber shoe at the bottom of legs with mild steel screws complete all as directed & shown on drg.

Taking out old & u/s long rail and S&F new long rail of size 1500 x 45 x 90 mm made out of 1st class well seasoned teakwood complete all as directed and shown on drg.

All as per item No 16.03 here-in-before but short top rail of size 900 X 45 X 90 MM .

Removing old & u/s MS Right angle from the corner of table dining 6 Pers and providing and fixing new one of size 150 x 30 x 5 mm with mild steel screws complete all as directed & shown on drg.

All as per item No 3.11 here-in-before but for Table dining 6 Pers.

FD/MAP-II/03 Table dining 4 Pers (MAP )

All as per item No11.01 here-in-before but for Table dining 4 Pers

Removing old & u/s legs of table dinning 4 pers & S/F new legs of size 750x45x90mm made out of 1st class well seasoned teakwood duly fixing PVC rubber shoe at the bottom of legs with mild steel screws complete all as directed & shown on drg.

Taking out old & u/s long rail and S&F new long rail of size 1200 x 45 x 90 mm made out of 1st class well seasoned teakwood complete all as directed and shown on drg.

All as per item No 16.03 here-in-before but short top rail of size 900 X 45 X 90 MM .

Removing old & u/s MS Right angle from the corner of table dining 6 Pers and providing and fixing new one of size 150 x 30 x 5 mm with mild steel screws complete all as directed & shown on drg.

(e) All as per item No 3.11 here-in-before but for Table dining 4 Pers.

FD/MAP-II/15® TableBed Side (MAP )

All as per item No11.01 here-in-before but for TableBed side

Remove the US handle of table Bed side and providing the new one chromium plated 75 mm ' D' Type as approved/directed by Garrison Engineer and fixing the same in its original position.

Removing old & u/s Hard rubber / PVC Shoe from Table Bed Side and supply and fixing new hard rubber / PVC Shoe to Table bed side at the bottom of legs complete all as directed & shown on drg.

Remove the US ply wood from the back of the table bed side MAP and providing the new one made out of 6mm green ply BWR commercial and fixing the same in its original position as per drg.

Tightening of complete steel frame of Table bed side by the help of scew driver or by welding and making functional.

FD-275 Table writing

(a) All as per item No 7.03 here-in-before but for Table writing.

(b) Taking out old u/s sides of table writing and S/F new sides made out of 19mm prelaminated particle board one side teak veneered complete all as directed & shown on drg.

(c) Removing of old u/s shutters of table writing and S/F new shutter made out of 19mm thick prelaminated particle board one side teak veneered bonded with phenol formaldehyde exterior gde including fixing of new or old serviceable hinges 50mm MS medium wt complete all as directed & shown on drg.

(d) Taking out old & u/s drawers from table writing and supply & fix with new drawers made out of prelaminated particle board & 1st cl well seasoned teakwood for sides & 6mm thick commercial plywood for bottom of drawers complete all as directed & shown on drg.

(e) Removing of u/s MS hinges from shutters and S& F MS butt hinges 50mm medium wt cold rolled mild steel.

(f) Removing of u/s knobs from shutters & drawers of table writing and supply & fix new 35mm round brass knob of approved quality complete all as directed.

(g) Taking out old & u/s plywood back of table writing & supply & fix new 6mm thick 5 ply plywood commercial BWR gde type BB fixed with 20mm mild steel screws complete all as directed & shown on drg.

(h) Taking out old U/S long legs of table writing and S&F new long legs made out of 1st class teak wood complete all as directed and shown on drg.

(j) All as per item No 19.08 mentioned here-in-before but short legs of table writing.

(k) Remove the old existing long stiffener of table writing and S&F new long stiffiner made out of 1st class well seasoned teak wood of existing shape & size and making functional.

(l) All as per item item No 19.10 mentioned here-in-before but short stiffners of table writing.

(m) All as per item 3.11 here-in-before but for table writing .

FD-1009 Table 900 X900 X 760 mm steel

(a) Removing of old and unserviceable top of table 900 x900 x760 mm steel and S&F new top made out of 18/19 mm thick pre-laminated particle board (ISI Marked) exterior grade one side teak veneered finish and other side having balancing white lamination with 19 x 4 mm teakwood beading all around the top and polishing the wooden frame shall be with french polish(to the entire satisfaction subject to minimum two coats ) including preparation of surfaces by scrapping /smoothing the surface all specified and shown on drawing .

( b) Painting to steel frame of table 900 x900x 760 mm steel by synthetic enamelled paint(min two coats) olive green colour including preparation of old painted surfaces by scrapping out old dirt staints etc to the entire satisfaction ( painting shall be done by using compressure spray machine)

(c) Electric welding to the broken /dislocated 25 x 25 mm square tube rails of tables 900 x900x 760 mm steel , length of welding exceeding 2.5 cm but not exceeding 5 cm ( each spots measured separately) thickness of metal to be welded not exceeding 6 mm , complete all as directed.

(d) Removing old unserviceable rubber shoes from the legs of 900 x900x 760 mm and S&F new rubber shoes off approved quality and tightly fitted and the bottom of legs all as specified and shown on drawing

FD-281 Sofa set 4 Seater

(a) Removing of old worn out u/s front legs of sofa set 4 seater and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(b) Removing of old worn out u/s rear legs of sofa set 4 seater and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(c) Removing of old worn out u/s front rail of sofa set 4 seater and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(d) Removing of old worn out u/s Back rail of sofa set 4 seater and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(e) Removing of old worn out u/s back wdn bearers of sofa set 4 seater and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(f) Removing of old worn out u/s bottom wdn bearers of sofa set 4 seater and providing /fixing new one made out of Teak wood well seasoned in existing shape and size and as directed by Engineer-in-charge.

(g) Remove the existing unserviceable sofa cushion from sofa set 4 seated and supply and fixing the new cushion 100 mm thick x 40 density of size 530x560mm covered with new tapestry cloth duly stitched.Make: Kurlon/sleep well

(h) All as per item 3.11 here-in-before but for sofa set 4 seater.

FD-281 Sofa set 2 Seater

(a) All as per item No 21.01 here-in-before but for sofa set 2 seater.

(b) All as per item No 21.02 here-in-before but for sofa set 2 seater.

(c) All as per item No 21.03 here-in-before but for long piece of sofa set 2 seater.

(d) All as per item No 21.04 here-in-before but for sofa set 2 seater.

(e) All as per item No 21.05 here-in-before but for sofa set 2 seater.

(f) All as per item No 21.06 here-in-before but for sofa set 2 seater.

(g) All as per item No 21.07 here-in-before but for sofa set 2 seater.

(h) All as per item 3.11 here-in-before but for sofa set 2 seater.

TP Chair Auditorium

Removing of existing unsv seat of Chair Auditorium and S&F new seat of make - Zuari, Model No. ZAC 102 and making functional.

Removing of existing unsv back of Chair Auditorium and S&F new back of Make- Zuari, Model No ZAC-102 and making functional.

Removing of existing unsv Arm rest of Chair Auditorium and S&F new arm rest of Make- Zuari, Model No ZAC-102 and making functional.

Changing of side pannel of chair Auditorium for its loosners and tightening of loosen side pannel by the help of removing old fashner and inserting new fashner of required size and tighten them.

Dry cleaning of chair auditorium upto the satisfaction of Engr-in-charge.

Tightning of loosen back of chair Auditorium and tightening them by inserting new Nut, bolt & washer of size 6 mm dia, 65 mm long.

FD-106 / 1038 Rack Steel 6 Tier

(a) Removing of unsv worn out back of rack steel and S & F new back to rack steel closed type made of MS Sheet of 1 mm thick of eixsting shape and size and making functional.

(b) Removing of unsv sides of rack steel and S &F new sidesmade of 1 mm thick MS Sheet in its original position as per drg & making functional

(c) Removing of unsv shelves of rack steel and S & F new shelves made of 1 mm thick MS Sheet in its originnal position as per drg & making functional

(d) Removing of unsv MS angle iron from rack steel and S & F new MS angle iron to rack steel closed type in its originzl position as per drg & making functional

(e) All as per item No 1.07 here in before but for Rack steel .

FD-42(M) Table 900x600x760mm without drawer FD-284,FD-88(M)

(a) Remove the old top and providing the new top made out of 18mm particle board one side laminated exterior grade with 4mm teak wood beading all around and fixing the same on table in its original position as per drawing and providing new hard rubber/PVC/Nylon shoes to the bottom of legs. Size of particle board shall be 900mm x 600 mm.

(b) Removing old u/s following components of table 900x600x760mm with or without drawer & S/F with new components made out of 1st class well seasoned teakwood free from knots, cracks, sapwood etc all as directed & as shown on drg :-

(i) Legs (size 740x60x30mm)

(ii) Long rails (740x25x65mm)

(iii) Short rails ( size 440x25x65mm)

(iv) Side rails (740x25x130mm) for FD/41/FD-284

(v) S& F new drawer

(c) All as per item No 3.11 here-in-before but for Table 900x600x760mm without drawer/with drawer.

FD-88(m) Table 900x900x760mm wdn

a) All as per item No 25.01 here-in-before but for Table 900x900x760 mm.

(b) Removing the following broken/damaged components/parts of table 900x900x760mm & S/F new components as under made out of Ist cl well seasoned teakwood all as per drg :-

(i) Legs of size (60x35x760mm long)

(ii) Top rails of size (75x25x900mm long)

(c) All as per item No 3.11 here-in-before but for Table 900x900x760mm .

FD-120 Chair CB Special W/Handrest

(a) Removing the worn out paint by scraping from the steel surface, necessary preparation of surface for painting and welding wherever required, two coat of spray painting with synthetic enamelled paint olive green over a coat of Metal primer after dent/bent portion. Wooden surface should be black polish to required glazed and shine.

(b) Removing the worn out u/s seat frame and providing/fixing the new one of existing size made out of 1st class teak wood duly re-caning with new plastic cane 2mm thick oval shape for general weaving and 4mm thick plastic cane for beading all around as show in drg. Wooden frame should be finished with black polish and fix in its original position with required screw(plastic cane type-I HDPE).

(c) All as per item 27.02 here-in-before but back frame.

(d) Removing the worn out u/s handrest made out of H.W(T.W) well seasoned and providing/fixing of exisiting size and shape with required screw after finish with black polish.

FD-220 Charpoy GI Pipe with ply top

(a) Remove the existing unserviceable Ply wood from Charpoy GI Pipe and making the frame to its original position by tightening etc and Supply & fixing with new ply wood 12mm thick, commercial, BWR Grade (IS-303) of existing shape & size and as directed by Engr-in-Charge.

(b) Removing the unserviceable/broken check nuts form GI charpoy & supply and fix 6mm thick GI Medium grade check nuts suitable for 32mm dia GI pipe all as specified and shown on drawings (Each check nut will be measured as single unit)

(c) Removing the unserviceable broken 3 way GI elbow from GI charpoy and S & F 32 mm dia GI medium grade 3 way elbow ISI marked all as specified and shown on drg and directed by Engr-in-Charge (Each GI Elbow shall be measured as single unit)

(d) Removing the existing unserviceable/broken long rail from GI charpoy and S & F new long rail of GI tubing 32mm including cutting, threading and bringing the GI charpoy into the original shape as shown on drawing and directed by Engr-in- Charge. (Make: TATA/JINDAL).

(e) Making short rails obtained from item No 28.04 above and fixing all as shown on drawing.

(f) Making legs out of unserviceable long/short rails obtained from item 28.04 and 28.05 above including cutting, threading and fixing all as specified and directed by Engr-in-Charge.

FD-1007 Table 900 x 600 x 760 mm Steel

(a) Removing old broken damaged top of table 900 x 600 x760 mm steel and S/F new top made out of 18/19mm thick prelaminated particle board one side teak veneered phenol formal dehyde exterior grade with 19x4mm teakwood beading fixed with headless nails all around the top.

(b) Removing the existing steel long rail from Table 900x 600 x 760 mm and S & F new steel long rail of size : 25mm x 25mm x 1.6mm thick. All as shown on drg and directed by Engineer-in-Charge.

(c) Remove the existing MS legs from Table 900 x 600 x760 mmand S & F new leg made out of 25mm x 25mm x MS tube 1.6mm aell thickness. All as directed by Engineer-in-Charge and as shown on drg.

(d) Remove the existing stiffner bottom and S & F new stiffner bottom made out of 25mm x 25mm, MS tube of 1.6mm wall thickness. All as directed by Engineer-in-Charge and shown on drg.

(e) Remove the existing short stiffner and S & F new short stiffner made out of 25mm x 25mm, MS tube of 1.6mm wall thickness. All as directed by Engineer-in-Charge and shown on drg.

(f) Remove the existing unserviceable shoes from Table 900 x 600 x760 mm and and S & F new PVC Shoes suitable for 25x2mm MS tube. All as directed by Engineer-in-Charge and shown on drg.

(g) Painting (Remove the existing worn out paint from Table 900 x 600 x760 mm and applying one coat of synthetic enamell paint black over a coat of primer. All as directed by Engineer-in-Charge and shown on drg.

FD/E6/MAP/12 Chair Writing Steel FD/E6/MAP/12 Replace the following parts of Chair writing Steel as shown in drawing and directed by Engr-in-Charge

(a) Seat shall be 12mm thick hot pressed plywood Upholstered with febric and moulded polyurethene foam with PVC lipping all round. The polyurethene foam shall be 50mm thick and shall be moulded with density 50-55 kg per cubic meter thick and hardness 20 kg on humpden machine

(b) Backshall be 12mm thick hot pressed plywood Upholstered with febric and moulded polyurethene foam with PVC lipping all round. The polyurethene foam shall be 50mm thick and shall be moulded with density 50-55 kg per cubic meter thick and hardness 20 kg on humpden machine

(c) Hand rest shall be made of black integral skin polyurethene with 75-85 shore 'A' Hardness & Reinforced with MS insrest. It shall be scratch and wheather Resistant Size 210mm (Inner) and 230mm (Outer)

FD-388® Charpoy IP Folding

(a) Remove the existing unserviceable Ply wood from Charpoy ip sq with ply and making the frame to its original position by tightening etc and Supply & fixing with new ply wood 12mm thick, commercial, BWR Grade (IS-303) of existing shape & size and as directed by Engr-in-Charge.

All as per item No 1.07 here-in-before but for Charpoy IP Folding

Deduct the total amount of credit against Sch 'A' Rs (-) 16,979.00/- (*) This amount is fixed and shall be deducted from the quoted amount of the bidder to arrive at contract sum.

Jaibalaji Enterprise

M/S MADAN MOHAN KAKAR