8168/2020-21/E8 PROVN OF TRAINING SHED AT CERTAIN UNIT AND OTHER SANCTIONED WORKS AT KIARI UNDER GE 860 EWS

Amount

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5 m depth for foundation etc and getting out in hard/dense soil complete all as specified and directed.

M & L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate as in sub base 75mm thick complete all as specified and as directed.

Walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted,built in cement mortar 1:6 complete all as specified.

M & L Precast cement concrete block masonry type B-1 1:2:4 (20mm graded crushed stone aggregate) with solid blocks, exc. 10cm in width and, setting in cement mortar 1:6 complete all as Specified.

Returning filling incl spreading watering and well ramming in layers not exceeding 25cm in hard and dense soil complete all as specified and directed.

Removing excavated material not exceeding 50 mtrs and depositing where directed at a level n. exc 1.5mtr above the starting point complete all as specified and directed.

M&L rendering in cement mortar 1:6, 15mm thick on fair face on concrete surface and finishing the surface even and smooth (without using extra cement) complete all as spd & directed.

M & L for preparing of new surfaces of any description and applying two coats of cement base paint on wall complete all as specified

Sand filling under floors or in foundation including watering and consolidation complete all as specified

M&L for broken stone or boulder hard core of gauge not exc 63 mm deposited spread and levelled in layers not exc.15 cm thick watered and rammed to a true surfaces complete.

M&L for 100mmm thick cement concrete type D-2, 1:4:8 (using 40mm graded crushed stone aggregate( in sub base concrete complete all as specified and directed by Engr-incharge

M& L for cement concrete 40mm thick type B - 1 , 1:2:4 using 20mm graded crushed stone aggregate over sub base and finishing the surface even and fair without using extra cement complete all as specified.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to ISI 1161-1998 grade St-240 complete all as specified

S&F Galvanised Corrugated mild steel sheeting 0.63mm thick with two corrugations side lap, as in wall cladding and roof of hangers and blast pens fixed with J or L hooks or cranked bolts and washers, wirh grade of zinc coatings 275 gm per sqm complete and all as Specified.

M&L 0.63 mm thick plain galvanised mild steel sheeting, in ridges, hips, valley gutter, drip and straight flashings fixed with L- type or J type or cranked hook bolts and washers with grade of zinc coating 275, all as specified and directed by engr-in-charge. complete all as specified and directed by Engr-in-charge.

M&L FI 40 x 6 mm thick as in roof sheet as in wind tie complete all as specified and directed by Engr-in-charge.

M&L for preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as spd.

M&L for 75mm thick cement concrete 1:3:6 type C -1 (using 20mm graded crushed stone aggregate) laid in alternate bays (not exc. 2 sqm each) as in plinth protection and finishing the surface even and smooth with using extra cement and providing joints throughout the thickness of plinth protection, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

Dismantling of wall and ceiling boards(Fibre, pulp, insulation, etc) or insulation board/slabs/blankets. any thickness, including cover fillets complete all as specified. (Note : Taking down carefully old FTL fitting recessed mounted light fittings/ceiling complete with all accessoeies and making necessary electric conection, complete all as specified and directed by Engr-in-Charge.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins etc, under 40sqcm in section (unframed work) all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as specified and directed.

M&L for Non-skid Ceramic tiles (colour or white as directed) 7 to 8mm thick (Square/rectangular) area of each tile exc 0.11Sqm but n. exc. 0.18sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including screed bed or bedding layer mortar in cement mortar 1:6, 15mm thick for laying floor finishes complete all as apecified and directed by Engr-in-Charge.

M&L for 5 to 6 mm thick Veneered decorative plywood grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with nails to timber frame work in wall complete all as specified and directed.

M&L for 5 to 6mm thick Veneered decorative plywood grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with nails to timber frame work in ceiling complete all as specified and directed.

S&F second class softwood plain fillets, square, rectangular or triangular in section clean sawn secured with nails sectional area exc 13 and not exc 25 Sqcm complete all as specified and directed.

M& L for 2nd class Softwood n. exc 6 sqm moulding as in cornices, picture rail and the like complete all as specified and directed.

M&L for 2nd class Softwood timber plain fillets square,rectangular or tringular in section clean swan scured with nails n.exc 3 Sqcm complete all as specified.

M&L for preparation of old painted steel surfaces and applying one coat of synthetic enamel paint on surface of any description over 10cm width or girth complete all as specified and directed.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty fixed with wodden beads n.exc 0.5 Sqm in each pane including hacking out old broken glases of any size complete. .

M&L for preparation of old painted surfaces of wood or wood based material and applying one coat of synthetic enamel paint on surface of any description over 10cm width or girth complete all as specified and directed.

Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed.

M&L point wiring complete for one light / bell / buzzer / exhaust fan point controlled by one no, 1-way switch.with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete wiring drawn through & PVC casing and capping of 25 mm and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fittings / junction boxes / inspection covers etc, with and incl concealed MS sunken box of suitable size flush with wall surface, covered with & incl 3 mm thick bakelite, laminated hylem sheet / Gang box for top cover suitable for fixing of piano type switches / sockets etc, complete all as specified and directed for the following :- (Note : The cost of MS sunken box with 3 mm thick bakelite, laminated hylem sheet top cover is deemed to be included in quoted rate.)

All as per srl item no. 33 here-in-before but one socket outlet 3 pin, 5 Amps on independent board, controlled by one no 5 Amp switch.

All as per srl item no. 33 here-in-before but one socket outlet 3 pin 5 amps on the same board controlled by one no 5 Amp switch.

All as per srl item no.33 here-in-before but with 2.5 sq mm FRLS copper wire and with 2.5 Sqmm FRLS copper earth wire for indpendent 15 Amp point. Note: The point wiring for power point will not be mixed with light/fan point circuit or not in the same conduit.

S&F Switch piano type, single pole, one way, 5 amps, 230 volts, complete all as specified and directed.

S&F Socket, two-in-one, 5 pin, 5 Amp, universal type, 230 volts, complete all as specified and directed.

S&F switch Socket combination, 6 pin, 5/15 Amp, multi purpose , 230 volts, complete all as specified and directed.

S&F angular lamp holder,PVC/Polycarbonate type with back plate suitable for batten fittimng , 230 volts, complete all as specified and directed.

S&F LED lamp 15 W complete all as specified and directed by the Engineer-in-Charge.

S&F 20 watt LED tube rod and making connecgtion of light fitting to ceiling rose by 23/0.0076 copper flexible wire complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing in replacement 20W 6000K LED batten and making connection to ceiling rose by 23/0.0076 copper flexible wire all a specified and directed at site. Make : Havells cat part No LHEXBXPNIN1W020 or equivalent in Crompton Greeves/Wipro/Philips

S&F, in repalcement, of Ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed.

S&F in replacement of DB, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 4 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed.

S&F in replacement of DB, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed.

S&F in replacement of MCB, C Curve type, 10 kA, 40 to 63 Amp, SPN with over load and short circuit protection, complete all as directed.

S&F in replacement of MCB, C Curve type, 10 kA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as directed.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level, connecting to the Galvanized iron earth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron and steel earth wire protected by provision of GI light grade pipe 15 mm bore including provision of concrete pit made from PCC ( 1:2:4) type B-1 (using 20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angle iron 40 x 40 x 6 mm and handle of 6 mm dia MS bar made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom, 1.50 metre long placed on top edge of earth plate, common salt & charcoal filling, with fixing arrangement , funnel, wire mesh and earth work in hard/dense soil , returning filling in and removal of surplus soil to a distance not exceeding 50 metres, all as per electrical plate No 5 of SSR 1991 Part-I and connecting to CBDB’s as specified or indicated including testing on completion .

Taking down old unsv building security light fitting and incluidng supply and fixing new energy saving bulk head fiting 12 watt made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protetion and impact resistance of IK07 as reqd to be mounting bracket in wall/floor to suit the opening of the fitting with FI clamp, nut, bolt and washers of suitable size including making connection complete all as specified and as directed by Engr-in-Charge.

Taking Down UNSV Cable and Supply and laying XLPE insulated armoured heavy duty electric cable with aluminium conductor (Stranded) 1100V grade cross-sectional area 25 Sqmm 4 core laid in trenches or passing through pipe or fixed on pole etc complete all as specified and directed by Engr-in-Charge.

Supply and laying XLPE insulated armoured heavy duty electric cable with aluminium conductor (Stranded) 1100V grade cross-sectional area 16 Sqmm 2 core laid in trenches or passing through pipe or fixed on pole etc complete all as specified and directed by Engr-in-Charge.

Material and labour for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick complete all as specified.

M & L sand cushioning to underground cable complete all as specified in clause 19.75 of SSR Part - I.

osho traders

M/S SHAMSHER ALI SUFI

M/S ABDUL SAMAD MIR

SONAM TUNDUP

MS MOHD SHAREF

M/S JAVED CONSTRUCTION COMPANY

M/S GEE AAR and SONS ENTERPRISES