GE(S) BTD 82 OF 2024-25 PROVISION OF MINOR AND LBW WORKS UNDER AGE BR II UNDER GE (SOUTH) BATHINDA AT BATHINDA MILITARY STATION Job No (81SA BTD Minor 30 of 24-25 81SA BTD Minor 18 of 24-25 81SA BTD Minor 26 of 24-25 and 81SA BTD LBW 09 of 24-25)

Amount

S & F Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm including CP waste fittings and LDPE pipes complete all as specified

S&F in stainless steel plate racks of size 900x600x250mm and thickness of SS strip of 1mm fixed wall etc.(Making drills in wall and fixing material is included in rate) complete all as specified and directed .

Cutting holes in brick walls built in cement mortar including making good dismantled portion in CM (1:3) or cement concrete (1:2:4) type B-1 exceeding half brick but not exceeding one brick complete all as specified and directed

M&L in marble work (Udaipur green slabs) not less than 15 mm to 16mm thick (table rubbed and polished) as in cooking platforms and like in cement mortar (1:4) in pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade all as specified including rounding the edges over & including 15mm thick screed in cement mortar 1:4 complete all as specified and directed

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

M&L for Cement concrete type B0 1:2:4 (using 12.5mm thick crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M&L for Formwork for rough flat surfcaces of concrete of sides and soffits of floor or roof beams, beam haunch?ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, (for flat fair faces) etc.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed) not less than 0.9mm dia or securing with clips complete.

Ditto as serial item No. 8 as above but 5 mm to 10mm dia as in spacers , binders and stirrups etc.

S&F in repairs CP grating (with or without waste hole), 125mm size, fixed on floor/nahani gully trap traps etc complete all as specified and directed.

S&F 16 mm CPVC pipe sdr 11and plain CPVC sdr 11 fitting with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm i complete all as specified and directed including takingdown GI tubing complete all as specified and directed by EIC

S&F 20 mm CPVC pipe sdr11and plain CPVC sdr11 fitting with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm i complete all as specified and directed including taking down existing GI tubing complete all as specified and directed by Engr-in-Charge

S & F in repairs 15mm bore chromium plated bib taps cast copper alloy with wall flanges, crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repairs 15mm bore, chromium plated stop valves fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S & F in repairs 20mm bore, gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repairs PVC waste pipe with socket suitable for connection to Waste fittings of 32/40mm dia, and of length minimum 75 cm complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out

Hard core, broken stone to gauge n exc 63 mm

Cement concrete Type C2 , 1:3:6 in foundations, filling and mass concrete (40 mm graded aggregate)

Sand filling under floors or in foundations including watering and consolidation

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade Fixed with grey cement and pigment

Providing and laying at ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete

M&L for prepration of new plastered or concrete Surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of water based over a coat of primer complete all as specified and directed

S&F 110 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

M&L Cement concrete Type B2, 1:2:4 (40 mm graded aggregate) in foundations, filling and mass concrete

Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to FE-290 Gde E-165.

Excavating in post holes in any type of soil (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm.

Cement concrete Type B2, 1:4:8 (40 mm graded aggregate) in foundations, filling and mass concrete

S&F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. Fe-410-Gde E-250) quality B

Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410-W (Gde E-250) quality A

Roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framming (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe 410-W (Gde E-250) quality A

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified.

S&F for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified.

M&L painting with synthetic enamel paint two coats including redoxide and preparing the new steel surfaces of any description over 10cm in width or girth.

Removing excavated material n exc. 250m but n exc. 500 m and depositing where directed.

Taking down chowkats or frame with shutter (without taking out shutter from the frame) not exceeding 1.50 sqm each as doors, windows & ventilators etc. and removal from site all as specified and directed

Supply & fixing factory made steel window box type using ERW hollow 'P' section and double angle frame, with side hung shutters (glazed shutter and fly proof shutter) including grill/guard bar of 8mm sq bar fixed horizontally @ 100 mm C/C complete including fittings like hinges, tower bolt, stop legs, lugs, handle, lock system etc. complete all as shown on drawing No BTD-903 Sheet No 1/2 and 2/2 or as directed by GE including fixing of lugs in PCC complete all as specified & directed. Note :- Note :- (i) The width /height as shown in drawing are tentative, however the same shall be adjusted as per actual opeining of window. GE will approved the variation in the size of window during execution at site. (ii) Glass, wire cloth and painting shall be measured and paid separately under respective item of Sch (iii) Provision of all other items as shown & specified in on drawings and Provision of cutting holes of suitable depth in wall for inserting lugs etc including making good dismantled portion with PCC (1:2:4) type B-0 using 12.5mm graded crushed stone aggregate and cement mortar (1:3) shall be deemed to be include in quoted rates.

Taking Down Chowkhats or Frame with Shutter ( with out taking out shutter from the frame ) exc 1.50 sqm not exceeding 4.0 sqm each as doors , windows aaa& ventilators etc and removal from site all as specified and directed

Supply and fixing factory made pressed steel frames of size 125 x 60mm (thickness of sheet shall be 1.25mm) for doors with one or more rebates including necessary lugs and lock strike plate, etc. and including fixing only butt hinges suitable Nos as directed for each leaf, and making good the wall with plaster in CM 1:6 complete all as specified and as directed by Engineer-in- charge. Note : - Butt hinges shall be measured and paid separately under appropriate item of BOQ as supply only.

S&F 2nd class HW 35mm thick facotry made panelled shutters with lock rail and panel of 9 mm bwp commercial ply of 12 mm veneered particle board with commercial veneering on both faces . The size of rail and stylr as per IS-1003 (pt-I) klin seasoned and chemically pressure treated complete all as specified .

S&F 300 mm long stainless steel sliding bolt plate type stove enamelled black with bright bolt not less than 12 mm dia with and including a minium of 6 carringe bolts and nuts four on bolt plate and two on stapple plate and fixed conforming to IS 15834-2008 complete all as specified and as directed.

S&F 200 mm long stainless steel barrel tower bolts, ISI market stove enamelled block with bright bolt and fixed conforming to IS 15833-2009 complete all as specified and directed.

S&F stainless steel door handle of size 100mm fixed with counter sunk head screws conforming to IS 208-2020 all as specifierd and as directed.

S & F factory made glazed and skeleton shutters 35mm thick using second class hard wood open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc; sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24(a); all as specified complete.

S&F stainless steel wire cloth, 0.56 mm nominal dia of wire & average width of aperture 1.18mm and fixed with stainless steel wire staples complete.

S & F 300 mm long MS ordinary rat tail rod pattern springs for doors including roller and roller plate complete.

S&F Sheet glass 4.00 mm thick ,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane

Material and labour for Plain cement concrete 1:3:6, type C-1, using 12.5mm graded stone aggregate as in back filling to pressed steel chowkats

Supply only stainless steel Butt Hinges, 100 mm size, medium weight, cold rolled fixed with screws/welding to wooded/steel frames or chowkats, complete all as specified and directed.

Material and Labour for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified and directed.

Material and Labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome complete all as specified and directed.

Demolition of brick work in cement mortar as specified and directed

Forming jambs, etc. To openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete in CM 1:4

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 all as specified and directed

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

Cutting holes in brick walls built in cement mortar including making good dismantled portion in CM (1:3) or cement concrete (1:2:4) type B-1 exc half brick but n.exc one brick complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish to a distance exceeding 1 km but not exceeding 2 km.

S&F glazed ceramic coloured tiles 9-10 mm thick 600 x 300mm size in verticle surface including 10mm thick bedding layer using type-I adhesive (thick bed fixing) confirming to IS-15477:2004 and pointed in epoxy grout to match the shade of tile including necessary cutting as per site requirement etc complete all as specified.

Dismantling stone slabs of any description or thickness in floors, apron etc laid bedded and pointed in any mortar complete all as specified and directed.

Pre-polished kota stone 18-20mm thick as in flooring, cills and stair case over cement screed base laid and jointed With grey cement slurry mixed with pigment to match the shade of the slab including rounding of edges laid over 15 mm thick screed bed in cm 1:6 complete all as specified and directed. Note : Full piece of kota stone to be used in window cills, tread and riser

Pre-polished kota stone 18-20mm thick in riser of steps, skirting, dado and pillar laid over 10 mm trhick cement mortar screed (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and directed.

Taking down Cement plaster including raking out joints hacking for key scrubbing down with water etc

Rendering 15mm thick in cement mortar 1:6 on other than fare face of brick work or concrete surfaces and finishing the surface even & smooth without using extra cement

Rendering 15mm thick in cement mortar in 1:4 on fare face of brick work or concrete surfaces even and smoothe without using extra cement & with using integral water proofing compound

Complete removal of existing treatment including filling depression with wall putty two coats on Old external wall surfaces of any description, preparation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology , complete all as specified and applying the following:- (a) M&L two coats of exterior acylic emulsion by using Airless spray and incl a coat of acrylic emulsion external primer complete all as specified.

Preparation of New external plastered wall surface complete all as specified complete all as specified and applying the following:- (a) Applying wall care putty in two coats on wall surface and smoothening the surface with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) two coat of exterior acylic emulsion by using Airless spray and incl a coat of acrylic emulsion external primer complete all as specified.

Complete removal of existing treatment on Old Internal wall surfaces of any desciption, preparation of surface by Mechanised sander having suction vaccum Bag using Smart periodical methodology, complete all as specified and applying the following :- (a) M&L for wall care putty in two layers on wall surface and smoothening the surface with sand papers / Mechanised sanding etc preparatory to paint as directed complete all as specified (b) M&L for two coat of acrylic distemper of approved tint over a coat of primer on old prepared surface by using Airless spray complete all as specified.

Preparation of New plastered Internal wall surface complete all as specified complete all as specified and applying the following:- (a) M&L wall care putty in two coats on wall surface and smoothening the surface with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified. (b) M&L two coat of Oil Bound distemper over a coat of chalk whitening priming by using Airless spray complete all as specified.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets etc complete all as specified and directed.

S & F 595x595mmx6mm thick Gypsum board laminated with PVC Sheet as in false ceiling including supply and fixing 'Tee" grid frame work made of GI sheet 0.30mm thick, bottom portion painted with cellular nitro painting, consisting angle cleats of size 25mm wide 1.6mm thick with flag fixed to RCC ceiling with dash fastener or wraping the suspending wire around the existing wooden/steel purlin/rafter for suslpending grid frame work of size 600mmx600mm suspended with 02 Nos, 1.60mm dia GI wire @ 600mm C/C on main Tee and fixed to T-grid as per manufacturer direction. The section consisting of main Tee 37mm x24mmx0.60mm thick, cross runner tee 37mmx24mmx0.60mm and. Perimeter angle 24mmx24mmx0.50mm thick shall be fixed to wall with GI screw of 40mm long @ 450mm C/C along the perimeter of wall including or wall including all as per manufacturer's instruction complete all as specified and directed

M&L Dubbing out average 10mm thick on irregular surface of ceiling in cement mortar 1;4 all as specified and directed by engr-in-charge .

Applying two coat of white wash on newly plastered surface of ceiling etc complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar in (1:3) finishing the surfaces even and smooth on ceiling complete all as specified.

Complete removal of existing surface finishes of ceiling and applying two coat of white wash on old plastered ceiling surfaces etc complete all as specified and directed.

FATEH ENTERPRISES (BID ID -3193230)

M/s Kamal Builders (BID ID -3186497)

rkkataria and sons (BID ID -3187546)