Construction of Skill Development Centre and Employement Centre at Vedasandur Town Panchayat of Dindigul District under MPLADS-2025-26

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Cement Concrete 1:4:8 (One Cement, Four sand and Eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Brick work in Cement Mortar1:5 (one cement and five sand) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification.

Reinforced Cement Concrete 1:1.5:3 (One Cement, One and a half sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [ The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete]. The Putty shoule be got approved by the Executive Engineer before use on work.

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:3 (One cement and Three sand), 10mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Providing weathering course with best quality of broken jelly of size 20mm uniform gauge in pure slacked lime (no sand to be used) over the roof slab in the proportion of brickjelly lime 32:121/2 by volume and laid over in a single layer and consolidated

Finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three M.Sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and painting the walls with two coats of Oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats with enamel paint over new iron work including cost & conveyance of all materials to site and all labour charges etc., complete.

Fabrication and supply & Delivery of MILD STEEL DOORS of the following Size with Double Leaf outer frame made of 35x35x5 mm equal M.S.L angle and shutter frame made of 25x25x5mm equal M.S L angle for Horizontal and Vertical members and the shutter frame strengthened by stiffeners of 2 Nos horizontal, 3 Nos. diagonal for each shutter using MS flat of size 20x5mm fully covered with 18 gauge plain M.S full sheet welded with shutter frame neatly and also fixing by welding 6 Nos. of hold fasts made of 35x35x5 mm equal M.S L angle, 2 Nos. of wind appliances, 3 Nos. of tower bolts,1 No aldrop, 3 Nos. of handles fixing the shutter with 6 Nos. of 6 inch hinges with outer frame of the door including painting the whole unit with one coat of best quality of red oxide primer for Community hall building.

Door D

Door D1

Ventilator

Fabrication and supply of MILD STEEL WINDOW of of the following size with Double Leaves outer frame made of 35x35x5 mm equal M.S.L angle, mullion section made of 25x25x5mm equal T section, Shutter Frame made of 25 x 25 x 5mm equal M.S.L angle for Horizontal and Vertical members and the shutter frame strengthened by stiffeners of 2 No. Horizontal for each shutter using 25 x 25 x 5mm equal M.S. T section fully covered with 18 gauge plain M.S full sheet welded with shutter frame neatly and also fixing by welding protective grill with 12mm square M.S rods at an interval of not greater than 10cm centre to centre to the outer frame,4 Nos. of hold fasts made of 35x35x5 mm equal M.S.L angle , 2 Nos. of peg stays with holes for keeping the windows open in different positions, 2 Nos. of locking handles, fixing the shutter with 4 Nos. of 4 inch hinges with outer frame of the window including painting the whole unit with one coat of best quality of red oxide primer for Community hall building

Window

Supplying and fixing of 110mm dia PVC pipe in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

Labour charges for Fixing Doors and Windows

Towards the cost of Name board charges

GST Amount for providing Service to Government Contract Works for the above Construction & Maintenance Works. { GST Amount is the Total GST Amount for overall quoted amount (Both Construction and Maintenance) above this row in column "BB" for all works in this package} (Refer Clause 13.2 & 13.3 of Section 2 of Instruction to Bidders (ITB) of SBD)

33DNTPK5626K2ZF (BID ID -1501230)