SUPPLY AND INSTALLATION OF OPEN GYM EQUIPMENT AT VARIOUS PARKS IN KAROL BAGH AND SOUTH ZONE UNDER MPLADS FUND IN HORTICULTURE DEPARTMENT, MUNICIPAL CORPORATION OF DELHI.

BACK EXTENSION DIMENSIONS: - 1400MM (LENGTH) X 700MM (WIDTH) X 820MM (HEIGHT). SAFE AREA: - 2.4MTR X 1.7MTR. BACK EXTENSION EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB PIPE. (NB STANDS FOR NOMINAL BORE I.E. INTERNAL DIAMETER OF PIPE IN MM) THE MAIN FRAME IS OF 50MM NB MADE FROM “C” CLASS G.I. PIPE. THE FOOT RESTING FRAME OF 32MM NB MADE FROM ”C” CLASS G.I. PIPE. THE HANDLE FRAME IS OF 25NB MADE FROM “C” CLASS G.I. PIPE. THE SEAT FITTED ON THE OUTER FRAMES IS MADE UP OF M.S. SHEET OF SIZE 330 MM X 300MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED IN TOOLS AND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES. THE FOUNDATION USED FOR FIXING IS CONSISTS OF 50MM NB MADE FROM ”C” CLASS G.I. PIPE.THE FOOTRESTS ARE MADE FROM INJECTION MOULDED PLASTIC LLDPE / HDPE. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF ATLEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE).

AIR WALKER PROVIDING AND FIXING AIR WALKER MADE FROM “C” CLASS GI PIPE. THE CENTER PIPE IS OF 80MM NB MADE FROM “C” CLASS MS PIPE, 32MM NB:- AIR WALKER PEDAL FRAME DULY BEND, 25MM NB:- AIR WALKER HANDLE FRAME DULY BEND AND THE BOTTOM SUPPORT OF M.S. ROUND PLATE OF 250 MM DIA& 10MM THICKNESS IS WELDED AT BOTTOM. MS PLATE OF 245 X 113 X 2.8MM :- FOOTREST SUPPORT PLATE. THE LEG MOVEMENT FRAME IS OF 40MM NB MADE FROM “C” CLASS MS PIPE. THE HANDLE FRAME IS OF 25MM NB MADE FROM “C” CLASS GI PIPE. THE FOUNDATION USED FOR FIXING IS CONSISTS OF THREE EQUAL ITEMS I.E. 80MM NB MADE FROM “C” CLASS GI PIPE, M.S. ROUND PLATE OF 250 MM DIA & 10MM THICKNESS & 25 MM X 25MM M.S. ANGLE OF 3 MM THICKNESS. MS PIPE 48 X 48 X 2.8MM:- FOOTREST FRAME SUPPORT. MS ANGLE 23 X 23 X 1.8MM:- FOUNDATION SUPPORT FRAME. MS FLAT 48 X 9MM:- FOUNDATION PLATE SUPPORT. MS BRIGHT MATERIAL:- PINS MADE OF DIA.25MM. MS PLATE OF 8MM:- AIR WALKER PEDAL L-BEND, SUPPORT. 60MM DIA SEAMLESS PIPE:- BUSHES. BEARINGS:- PERMANENT LUBRICATED BEARINGS 6205. CLOSING CAPS MADE FROM TOP QUALITY FRP MATERIAL WITH 2 MM THICKNESS. HDPE / LLDPE PLASTIC :- CLOSING CAP, AIR WALKER FOOTREST. THE PINS USED ARE MADE UP OF 25MM DIAMETER BRIGHT BAR. THE BEARINGS USED BE PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM S.S. MATERIAL. THE SER CLIPS USED FOR ASSEMBLY ARE OF 25 MM DIAMETER. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

HORSE RIDER DIMENSIONS: - 1180MM (LENGTH) X 400MM (WIDTH) X 1400MM. (HEIGHT). SAFE AREA: - 2.2MTR X 1.4MTR. HORSE RIDER EQUIPMENT MADE FROM “C” CLASS G.I. PIPE OF DIFFERENT NB.NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE MAIN FRAME OF 100NB MADE FROM “C” CLASS G.I. PIPES WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. SEAT PROVIDED ARE MADE UP OF MS DEEP DRAW QUANTITY OF 2MM THICKNESS WITH NO JOINT WITH UNIFORM OUTER EDGE RADIUS 20MM. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80 NB “C” CLASS WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLES OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPES OF 3MM THICKNESS. THE LEG MOVEMENT FRAME IS OF 32NB MADE FROM “C” G.I. PIPE. THE HANDLE FRAME IS OF 32 NB MADE FROM “C” CLASS G.I. PIPE. THE FOOTRESTS ARE MADE FROM 25 NB “C” CLASS G.I. PIPE. PINS USED OF DIAMETER 17 MM ARE MADE UP FROM SAE 8620 BRIGHT MATERIAL. N THE BEARINGS USED OF “62032RS1” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND. HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS FOR ASSEMBLY. THE SER CLIPS USED FOR ASSEMBLY ARE OF A24 MM. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE).

ARM AND PADDLE BIKE (DIMENSIONS: - - 1100MM (LENGTH) X 500MM (WIDTH) X 900MM (HEIGHT). SAFE AREA: - 2000MM (LENGTH)X1000MM(WIDTH). ARM AND PADDLE BIKE MADE FROM “C” CLASS GI PIPE. THE CENTER PIPE IS OF 40MM NB MADE FROM “C” CLASS GI PIPE. THE HANDLES IS MADE UP OF CASTED IRON MATERIAL WITH PLASTIC HOLDING GRIPS. FOR FOUNDATION HOLE PASS PROVISION IS PROVIDED. THE FOOTRESTS IS MADE FROM ALUMINUM CASTING MATERIAL, ITS SIZES ARE 130 MM X 300 MM & 3 MM THICKNESS. THE SEATS AND BACK RESTS ARE FITTED ON THE OUTER FRAMES ARE MADE UP OF M.S. SHEET OF SIZE 330 MM X 300 MMX2MM THICKNESS AND DEEP DRAWN AND PRESSED IN TOOLS AND DIES TO HAVE UNIFORM RADIUS OF 20 MM WITH NO SHARP EDGES. THE PINS USED IS MADE UP OF 25 MM DIAMETER HARDEN LOW CARBON STEEL. THE BEARINGS USED IS OF “6205” PERMANENT LUBRICATED SEALED BEARING. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM S.S. MATERIAL. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBODED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE).

TRIPPLE TWISTER STANDING DIMENSIONS: - 1150MM (LENGTH) X 1150MM (WIDTH) X 1580MM. (HEIGHT). SAFE AREA: - DIA 2.1MTR. TRIPLE TWISTER MADE FROM “C” CLASS GALVANIZED IRON (G.I.) PIPE OF DIFFERENT NB. NB STANDS FOR NOMINAL BORE SIZES I.E. INTERNAL DIAMETER OF PIPE IN MILLIMETERS. THE CENTER PIPE IS OF 100NB MADE FROM OR “C” CLASS G.I. ROUND PIPE. THE BOTTOM SUPPORT WELDED IS OF M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. THE STANDING FRAME IS OF 32NB MADE FROM “C” CLASS G.I. PIPE. THE HANDLE FRAME OF TRIPLE TWISTER IS OF 25 MM NB MADE FROM OR “C” CLASS G.I. PIPE. THE FOUNDATION USED FOR FIXING IS A STRUCTURE AND MADE FROM CENTER PIPE OF G.I. OF 80MM NB OR “C” CLASS WELDED WITH M.S. ROUND PLATE OF DIA 250 MM & 10MM THICK. MAIN PIPE SUPPORTED WITH 25 MM X 25MM M.S. ANGLE OF 3 MM THICKNESS AND 20MM X 40MM CRC SQUARE PIPE OF 3MM THICKNESS THE STANDING PLATE IS FITTED ON THE FRAME MADE UP OF DIA 80MM SEAMLESS PIPE. M.S. ROUND PLATE OF SIZE DIA 300MM X 10MM THICKNESS. CLOSING CAPS OF TOP QUALITY FIBER REINFORCED PLASTIC MATERIAL WHICH IS OF 2 MM THICK. THE PINS USED ARE MADE UP OF DIA 25 MM SAE8620 BRIGHT MATERIAL. THE BEARINGS USED ARE OF “6205ZZ” PERMANENT LUBRICATED SEALED BEARING OF REPUTED BRAND (FAG/SKF). HIGH TENSILE STEEL WITH GALVANIZED NUTS & BOLTS ARE USED FOR ASSEMBLY. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

SHOULDER BUILDER PROVIDING AND FIXING SHOULDER BUILDER MADE FROM C- CLASS GI PIPE. THE CENTER PIPE IS OF 100MM NB MADE FROM “C” CLASS GI PIPE, AND THE BOTTOM SUPPORT OF M.S. ROUND PLATE OF 250 MM DIAMETER & 10MM THICKNESS IS WELDED AT BOTTOM. THE HANDLE MOVEMENT FRAME IS OF 25 NB & 20 NB MADE FROM “C” CLASS GI PIPE. TO JOIN THE CENTRE PIPE & HANDLE MOVEMENT FRAME SEAMLESS PIPE OF 130MM DIA& 3MM THICKNESS IS USED. THE FOUNDATION USED FOR FIXING CONSISTS OF THREE EQUAL ITEMS I.E. 100MM NB MADE FROM “C” CLASS GI PIPE, M.S. ROUND PLATE OF 250 MM DIA& 10MM THICKNESS & 25 MM X 25MM X 3MM M.S. ANGLE. CLOSING CAPS MADE FROM TOP QUALITY FRP MATERIAL WHICH IS OF 2 MM THICKNESS. THE PINS USED ARE MADE UP OF 25 MM DIA BRIGHT BAR. THE BEARING USED BE PERMANENT LUBRICATED SEALED BEARING OF REPUTED MAKE. THE NUT BOLTS USED FOR ASSEMBLY ARE MADE FROM S.S. MATERIAL. THE SERCLIPS USED FOR ASSEMBLY IS OF 25 MM DIAMETER. THE POLY URETHIN PLASTIC BUSH IS USED FOR HANDLING. THE GYM EQUIPMENT SHALL BE FINISHED SMOOTH WITH A PRIMER COATING OF AT LEAST 40 MICRON FOLLOWED BY EPOXY BASED POWDER COATING WITH POLYSTER POWDER COATING OF AT LEAST 60 TO 70 MICRON THICKNESS USING EXONOBEL / BERGER MAKE PAINTS OR ITS EQUIVALENT PAINTS. THE HOLDING DOWN/FIXING OF GYM EQUIPMENTS SHALL BE EMBEDDED IN CEMENT CONCRETE IN THE RATIO OF 1:2:4 (1CEMENT : 2 COARSE SAND :4 STONE AGG. 20MM NOMINAL SIZE)

SEATED PULLER /PULL CHAIR made from “C” Class G.I pipe. DIMENSIONS: - 1900mm (Length) x 740mm (Width) x 1920mm. (Height). SAFE AREA:- 1.2Mtr x 3Mtr. Seated puller equipment made up of “C” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The center pipe is of 100NB made from “C” Class G.I. pipe. Bottom support is of M.S. round plate of DIA 250 mm & 10mm thickness welded. All linkages are made up of 25NB “C” class G.I. pipe. The handle frame is of 32NB “C” class G.I. pipe. The seat frame is of 32NB “C” class G.I. pipe. To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class. Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Foundation Cover Closing Cap is made from Injection Moulded Plastic LLDPE / HDPE. The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges.Closing Caps are made up of from Injection Moulded Plastic LLDPE / HDPE.Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. The bearings used are of “6205 2RS1” and “6203 2RS1” permanent lubricated sealed bearing of reputed brand.High tensile steel with galvanized nuts & bolts are used for assembly.Thecirclips used for assembly are of A16. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).

DIMENSIONS: - 1320mm (Length) x 600mm (Width) x 1750mm. (Height). SAFE AREA: - 1.77 x 1.2Mtr. Cross trainer equipment made from “C” Class G.I. Pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame Pipes are of 80NB “C” Class G.I. Pipe with single bend pipe with 250mm radius. The bottom support of M.S. round plate of DIA 250 mm & 10mm thick. The Handle Frame is made up of 25NB “C” Class G.I. Pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. To build structure bushes are used which are made from M.S. seamless pipe of 60mm OD With 5 mm thickness. The footrests are made from Injection Moulded Plastic LLDPE / HDPE. Closing Caps are made up of Injection Moulded Plastic LLDPE / HDPE. Pins used of Diameter 35mm, 25mm, and 17mm are made up from SAE 8620 bright .The Bearings used are of “6007 2RS1” “62052RS1” and “62032RS1” permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster CROSS TRAINER /ELLIPTICAL EXERCISERPowder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size). A16 , A 24 mm circlips are used for assembly. Bolt M8X16 mm and NY lock nut of M8 made of SS304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.

SIT UP BOARD FOR USE OF TWO PERSONS AT ONE TIME. DIMENSIONS: - 1820mm (Length) x 430mm (Width) x 580mm (Height). Safe Area:- 2.8Mtr x 0.6Mtr. Sit up Board Equipment made from “C” Class G.I. pipe of different NB.NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. The main frame is of 50mm NB made from “C” Class G.I. pipe in a single bend and supported with the MS round plate of DIA 250x10mm thickness. Fiber reinforced Plastic sheet of 3mm thickness is Bounded on 25mm NB (G.I.) “C” class pipe of main frame. The base support of the sit up board is made 40NB (G.I.) “C” class pipe. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB “C” class Welded with M.S. round plate of DIA 250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. The Gym Equipment shall be finished smooth with a primer coating of atleast 40 micron followed by epoxy based Powder Coating with Polyster Powder Coating of at least 60 to 70 micron thickness using Exonobel / Berger make paints or its equivalent paints. The holding down/fixing of Gym Equipments shall be emboded in cement concrete in the ratio of 1:2:4 (1cement : 2 coarse sand :4 stone agg. 20mm nominal size).