SPECIAL REPAIR TO OTHER RANK MARRIED ACCN BUILDING NO P 86 AND PROVN OF 01 HIGH MAST WITH LED LIGHT 250 WATT FITTINGS QTY 06 AT CHILDREN PARK NEAR MI ROOM AT ADM AREA CPE ITARSI UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Demolition of un reinforced cement concrete of any description and in any position not otherwise specially provided for complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement morter bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in roof kerbs or mud stops, bed blocks, benching etc including necessary form work complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in sub base for floors complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in plinth protection/ pavements, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 30 mm thick cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in sub base of flooring, surface finished rough to receive floor topping complete all as specified and directed.

M&L for non-skid ceramic tiles coloured 7 to 8 mm thick (square/ rectangular), primium quality, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc; set and jointed in neat cement slurry and pointed in white or coloured cement to match colour of tiles over and including 15 mm thick screed bedding in CM (1:6) complete all as specified and directed.

M&L for non- skid ceramic tiles 8 to 9 mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors etc; set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bedding in CM (1:6) complete all as specified and directed.

M&L for non- skid ceramic tiles 7 to 8 mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in skirting or vertical surface; set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and directed.

M&L for glazeded ceramic coloured tiles (colour & shade as approved) of size 350x250x7 mm/ 450x300x7mm thick on vertical surface such as skirting, dados etc; set and jointed in neat cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white/ coloured cement with pigment to match the colour of tiles complete all as specified and directed.

M&L for 20 mm thick granite stone slab in single piece inclusing bull nosing at front and sides as in steps, jambs, pillars, window cills, cooking platforms, staircase and like, jointed in CM (1:4) andl pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including making grooves for slip guard or steps, edge moulding and making 30 mm dia hole in cooking counter slab and for gas pipe over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations with requited T&P complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:4) mixed with integral water proofing compound as per manufacturer instructions over the padding concrete while still the concrete is still green on roofs complete all as specified & directed.

M&L for water proofing treatment to roof surface including parapet wall comprising with the following course of treatment/ specifications from bottom to top:- (a) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.2 kg per sqm over a coat of bitumen primer @ 0.30 ltr per sqm including preparation of roof surfaces complete as directed. (b) Applying a layer of APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3 mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) landed on primed surface by forced application complete as directed. Note:- (i) Polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet walls and shall be finished by a membrane flashing. (ii) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions. (iii) A minimum overlap shall be 75mm length wise and 100 mm width wise of polymeric membranes respectively and sealed all overlaps and joints as manufacturer's instructions.

M&L for cement concrete tiles 25cm x 25cm x 22mm thick, machine pressed; set and jointed in neat cement slurry over and including 15 mm thick screed bed in cement mortar (1:4) and pointed in neat cement mixed with grey cement and pigment to match the shade of tiles complete all as specified and directed.

Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins, arches, pillars etc complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Labour only for brick work using old bricks retrieved from dismantling after cleaning and removal of mortar from old bricks etc; straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

Taking down cement plaster on brick walls of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 12 mm thick in cement mortar (1:6) on fair faces of brick walls or concrete surfaces, finished fair and even without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:4) on other than fair faces of brick walls or concrete surfaces, finished fair and even without using extra cement using WPC as per manufacturer instructions complete all as specified and directed. Note: WPC shall be measured and paid separately.

Supply only integral water proofing compound (WPC) ISI marked complete all as specified and directed.

M&L for rendering 10 mm thick cement plaster on ceiling surfaces in cement mortar 1:3, finished fair and even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying two coats of white washing complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling and applying one coat of white washing complete all as specified and directed.

M&L for applying two coats of oil bound distemper over a coat of wall primer on new plastered surface of walls including preparation over and including a coat of 2mm thcik wall care putty, finished even and smooth and making the edges properly complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of Oil bound distemper over a coat of wall primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of white washing complete all as specified and directed.

M&L for preparation of old plastered/unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil & greasy spots and applying a coat of white wash on walls complete all as specified & directed.

M&L for complete removal of old existing treatment on plastered surface of walls and preparation of surfaces and applying two coats oil emulsion distemper over and including 1 mm thick coat of wall care putty to make the surface even and smooth complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm on newly plastered surfaces of walls including preparation complete all as specified and directed.

M&L for complete removal of all existing treatment including preparation of old plastered surfaces of walls and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size not exceeding 1.5 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) of size exceeding 1.5 sqm and not exceeding 4 Sqm each complete all as specified and directed.

Taking down shutters of size exceeding 1 Sqm and n. exc 2 sqm each complete all as specified and directed.

S&F of 30 mm thick flush shutters factory made, solid core construction with block board core, plywood face panels, both side covered with decorative face veneers with lipping/ frame to match complete all as specified and directed.

S&F of factory made single extruded WPC (Wood polymer composite) soild door/window /ceosetory windows and other frames/chowkat of size 65x100mm comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fib (wwod powder/rice husk/wheat husk) and fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minumum frame densit of 750 kg/cum screw withdrwal strenth of 2200 N (Face) and 1100 N (Edge) minumum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with properly of being termite/ borer proof, water /moisture proof and fire retardant and fixed in position with MS hold fast/lug/SS dash fastteners of required dia and length complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F of factory made single extruded WPC (Wood polymer composite) soild door/window /ceosetory windows and other frames/chowkat of size 65x125mm comprising of virgin PVC polymer of K value 58-60 (suspension grade) calcium carbonate and natural fib (wwod powder/rice husk/wheat husk) and fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minumum frame densit of 75 0kg/cum screw withdrwal strenth of 2200 N (Face) and 1100 N (Edge) minumum compressive strength of 58N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of class A category with properly of being termite/ borer proof, water /moisture proof and fixed in position with MS hold fast/lug/SS dash fastteners of required dia and length complete all as specified and directed. Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F of factory made 30mm thick 100% Solid WPC (Wood polymer Composite) Laminated Wiremesh Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 (Suspension Grade), Calcium Carbonate and natural fibers (Wood Powders/ rice husk/ heat husk) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with having minimum density not less than 650 kg/cbm having good screw holding capacity (Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compressive of 50 N/mm2, Modulus of elasticity 850 N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter. For fixing Mosquito mesh and XTN aluminium mesh combinly panel area of door except stiles and rails to be panelled with mesh with self tapping round headed scresws at required distance, scres and edges covered with feathered pvc edge beading all around of mesh and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws complete all as specified and directed. Note: Material test certificate and authentication should be compulsory provided by the manufacturing company.

S&F of factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws complete all as specified and directed.

S&F of stainless steel plate rack of standard pattern of size 900 x 750 x 250 mm, thickness of stainless steel sheet shall be 1.00 mm & grade of sheet shall be 304 AISI fixed to wall with 4 Nos 50 mm long screws & PVC rawl plugs complete all as specified and directed.

S&F of aluminium powder coated aluminium window having three track with aluminium section 92 x 31.75 mm (Weight bottom section 1.070 kg/m, top section 0.933 kg/m), shutter section 40 x 18 mm (weight of handle section 0.417 kg/m) interlock 0.547 kg/m mounted on bearing to slide on tracks plain anodized in approved shade including supply and fixing of 5 mm thick plain glass and SS wire mesh, PVC track gasket, EPDM rubber gasket on glass of weather tightening along with locks, handle including sealing gap with marble surfaces with silicon sealants making it water proof in all manner etc. complete all as specified and directed. Note: Min. thickness of powder coating shall be 50 micron.

S&F of aluminium powder coated ventilator having fixed glass with aluminium section having section 50.80 x 25.40 mm (weight 0.489 kg/m) glazing clear section (weight 0.109 kg/m) with plain anodized including supply and fixing of 5mm thick frosted glass making frame and glass water tightening making it good etc. complete all as specified and directed. Note: Min. thickness of powder coating shall be 50 micron.

S&F of pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in chajja roof covering/ cladding to wall, fixed with self tapping screws or with 'J' or 'L' hook / suitable screws complete all as specified and directed.

S&F of mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work con- forming to Fe-290 Gde E-165 complete all as specified and directed.

S&F of Solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube complete all as specified and directed.

S&F of factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top and bottom rail MS frame shall be covered with heat moulded plain / coloured PVC "C"channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the styles & rails with suitable PVC sheet beading and jointed togeather with solvent cement complete all as specified and directed.

S&F for mild steel framed brackets for chajjas of angles or tees with web and flanges, cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary,gusset plates, riveting, etc; not exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Dismantling of boarding, any description, fixed in any position fixed with nails / screws complete all as specified and directed.

S&F of block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face and board fixed to timber/steel frame work with screws including if any damaged/broken of existing surface during the fixing arrangement of cabinet and making good existing surface with the same material complete all as specified and directed.

M&L of second class hard-wood as in scantlings, wrought and timber fixed complete all as specified and directed.

S&F of 12 mm thick plywood No 7 grade veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces fixed with screws as in cupboard shutter to timber/steel frame work complete all as specified and directed.

Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 complete all as specified and directed.

S&F of 100mm long hasp and staple, mild steel, wire type, aluminium anodised including bolt to hinges plate and fixed with screws complete all as specified and directed.

S&F for providing external teak wood lipping, 6 mm thick fixed with nails on 18/19 mm thick block board complete all as specified and directed.

S&F for providing external teak wood lipping, 6 mm thick fixed with nails on 12 mm thick plywood complete all as specified and directed.

S&F of continous (piano) hinges of mild steel bright finish or electro galvanised with flap (when open) 30 mm and fixed with steel screw complete all as specified and directed.

S&F for stainless steel clip on soft close clip on 3D hydraulic concealed hinges for full overlay door as kitchen cabinet complete all as specified and directed.

M&L for preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for a coat of synthetic enamel paint on old painted wooden surfaces of any description over 10cm width or girth including preparation of old painted wooden surfaces complete all as specified and directed.

M&L for a coat of synthetic enamel paint on old painted steel surfaces of any description over 10cm width or girth including preparation of old painted steel surfaces such as trussees, purlins etc. complete all as specified and directed.

S&F of 125 mm size mild steel butt hinges medium weight, cold rolled and fixed with steel screws complete all as specified and directed.

S&F of aluminium tower bolts 150 mm long and fixed with steel screws complete all as specified and directed.

S&F of aluminium bow handle 150 mm long and fixed with steel screws complete all as specified and directed.

S&F of aluminium anodised handles 100 mm long and fixed to cupboard shutter etc. complete all as specified and directed.

S&F of 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F of 150 mm floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring and fixed with screws complete all as specified and directed.

S&F of 300 mm long mild steel ordinary rat tail spring including roller and roller plate and fixed complete all as specified and directed.

M&L for cutting chases, pinning in. making good to facings where required for brick wall and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc; and making good, cutting not exc 10 cm girth complete all as specified and directed.

Taking up or down existing steel water tubing, 15 mm bore alongwith connections fixed/laid in any situation complete all as specified and directed.

Taking up or down existing steel water tubing, 20 mm bore alongwith connections fixed/laid in any situation complete all as specified and directed.

Taking up or down existing steel water tubing, 25 mm bore alongwith connections fixed/laid in any situation complete all as specified and directed.

S&F for GI steel water tubing, 15 mm bore medium grade galvanized with all fittings and fixed to walls and celling or laid in floor complete all as specified and directed.

S&F for GI steel water tubing, 20 mm bore medium grade galvanized with all fittings and fixed to walls and celling or laid in floor complete all as specified and directed.

S&F for GI steel water tubing, 25 mm bore medium grade galvanized with all fittings and fixed to walls and celling or laid in floor complete all as specified and directed.

S&F in repair stop valves, Stop valves, cast copper alloy, chromium plated, fancy type with long shank and cup ( concealed type ) screwed down, high pressure, with capstan head, screwed both ends for 15mm bore iron pipe complete all as specified and directed.

S&F in repair gunmetal gate valve of class-2, 15 mm dia with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F in repair gunmetal gate valve of class-2, 20 mm dia with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F in repair gunmetal gate valve of class-2, 25 mm dia with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F in repair bib taps, cast copper alloy, chromium plated, fancy type with capstan head, screwed for 15 mm bore of iron pipe and fixed complete all as specified and directed.

S&F in repair stop valves/angle cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed for 15 mm bore of iron pipe and fixed complete all as specified and directed.

S&F in replacement Vitreous china wash basin, white/ coloured, flat back, size 550x400mm including PTMT waste fittings, 32mm bore PVC drain pipe and making good disturbed surfaces to match with the existing complete all as specified and directed.

S&F in repair Pillar taps, cast copper alloy, chromium plated, fancy type with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for 15 mm bore iron pipe complete all as specified and directed.

S&F in repair low density polyethylene (LDPE) pipes 32mm bore of pressure rating 6 kgf/ sqcm complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F of 20mm dia nipple suitable for HDPE water tank and fixed complete all as specified and directed.

S&F in replacement 500 ltrs capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), triple layer, hoisted and fixed in position with and including 20 mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe as specified in SSR Part-I complete all as specified and directed.

S&F in replacement vitreous china squatting pan, Orissa pattern, size 580x440mm white with integral foot rests including flush pipe and connection to trap and to flushing pipe, anti-syphonage pipe, etc. And making good floor complete all as specified and directed.

S&F in repair PVC 10 ltrs capacity valveless syphonic action type, flushing cictern, low level, white/ coloured with inlet, ball valve, float and handle including brackets and connection to pipe etc. complete all as specified and directed.

S&F in repair 125 mm size stainless steel shower rose with or without swivel joints any size with arm including fixing to 15 mm bore steel pipe complete all as specified and directed.

S&F in repair towel rail, 20mm dia brass chromium plated, 600mm long with fancy type with brackets on both sides and fixed to walls with steel screws and wooden/rawl plugs complete all as specified and directed.

S&F in repair cromimum plated SS soap dish (not less than 1mm thick) of any type and fixed to walls with chromium plated brass screws with wooden/rawl plugs complete all as specified and directed.

S&F in repairs kitchen sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar or to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460mm & bowl size 410mm x 330mm x 160mm including SS waste coupling and PVC waste pipe complete all as specified and directed.

Dismantling of 75/100mm bore cast iron/PVC/AC/Cement concrete pipes, jointed in cement mortar or taking out from wall/trenches as required complete all as specified and directed.

S&F of 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches complete all as specified and directed.

S&F of 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints and fixed to walls or laid in trenches complete all as specified and directed.

S&F of 75mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F of 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F of 75mm dia Junction single (Single or double T) equal or unequal complete all as specified and directed.

S&F of 110mm dia Junction single (Single or double T) equal or unequal complete all as specified and directed.

S&F of PVC (SWR) floor trap 75 mm, plain with PVC grating including jointing with solvent cement etc; complete all as specified and directed.

S&F in repair mild steel curtain rod powder coated with side brackets, end cups, rings @ 10 Nos per running metre and fixed with PVC rawl plugs & steel screws complete all as specified and directed.

M&L for 15 mm thick rendering over concrete surface of sunken floor in CM 1:3 on wall and sunken floor, finished even and smooth without using extra cement but using WPC as per manufacturer instructions complete all as specified and directed. Note: WPC shall be measured and paid separetely.

M&L for water proofing treatment to RCC sunken floor including wall comprising with the following course of treatment/ specifications form bottom to top:- (a) Applying evenly a tack coat of industrial bitumen 85/25 @ 1.6 kg per sqm over a coat of bitumen primer @ 0.40 ltr per sqm including preparation of roof surfaces complete as directed. (b) Applying APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) landed on primed surface by forced application complete as directed. Note: (i) Laying of APP based membranes shall be done by torch on method or as per manufacturer's instructions. (ii) A minimum overlap shall be not to be less than 150mm of polymeric membranes and sealed all overlaps and joints as manufacturer's instructions. (iii) All CI/PVC traps in sunken slabs to be enclosed with PCC 1:1.5:3 (min 15 cm) all round as directed.

M&L for cement concrete (1:5:10) type E-2 (using 40 mm graded stone aggregate) as in filling in sunkan slab or in sub base, mass concrete etc complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

M&L for reinforced cement concrete, nominal mix (1:2:4), type B1 (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) for fair flat surfaces of concrete complete all as specified and directed.

S&F of mild steel TMT bars as in reinforcement 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

S&F of 0.80 mm thick mild steel plain black sheet as; covering to door shutters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed,holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and directed.

M&L for forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A' complete all as specified and directed.

M&L for cement concrete 1:3:6, type C-2 (usiing 40mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

M&L for performing fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc. complete all as specified and directed.

Cutting into existing drain for connecting new drains of 150mm bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

M&L for PCC 1:3:6, type C-1 (using 20mm graded stone aggegate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for cleaning the blockage of bathroom/kitchen by cleaning the nanhi traps / gully traps and removing all the mud / sludge and getting out washing throughly traps, CI waste pipe by opening the cleaning eyes and depositing the sludge in a pit of suitable size at a distance not exceeding 100m from the gully trap and covering the same with the soil obtained from excavation of pit including excavation and earth work complete all as specified and directed.

Taking down carefully aluminium / copper point wiring with surface/ concealed PVC conduit or wooden batten ( light, fan, socket, bell or power ) including sunk in cast iron / pressed steel terminal boxes including fitting such as switches, ceiling roses, lamp holders, sockets, regulators, call bell, light fitting any sketch etc and making good disturbed surfaces of walls, floors etc complete.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor FRLS cable 1100 volts grade drawn into and including concealed rigid non mettalic PVC conduit medium grade not less than 19/20 mm (ISI marked) with all fitting and fixing accessories including sunk in pressed steel terminal boxes, conceled in wall & maching the existing surface with and incluidng 2.8 mm thick hylum brand laminated white bakelite sheet cover or metal flush box and white sheet cover of any module as required for mounting switches, sockets, fan regulators, etc and 1.5 sq mm multi stranded copper conductor cable as continuous earth wire drawn with wiring and connected to common earth dolly complete all as specified and directed for the following :-

(a) One light point/fan point controlled by one switch

(b) One light point controlled by two way switch

(c) One socket outlet 5 Amps controlled by one switch on the same board.

(d) One socket outlet 5 Amps controlled by one switch on independent board.

(e) One bell / buzzer controlled by one bell push.

All as per item No. 121 above but with 2.5 sq mm multi stranded copper conductor cable for one 15 Amps socket outlet controlled by one switch on independent board and 1.5 sq mm PVC insulated multisranded copper conductor cable as continuous earth wire complete.

S&F of single pole and neutral enclosure with a two pin and earth plug and socket complete with and including one single pole MCB SP/DP 10A, 20 Amps complete all as specified and as directed.

M&L for sub main wiring with two single core 4.0 sqmm multi stranded copper conductor, FRLS PVC insulated, unsheathed cable including rigid non metallic PVC conduit medium grade, ISI marked, 20 mm dia for sub main wiring with and including 2.5 sqmm FRLS PVC insulated and unsheathed stranded copper conductor as earth wire in concealed in wall & matching and making good to the disturbed surfaces to match with the existing surfaces including taking down existing unserviceable submain of any size complete all as specified and directed. Note:- Two runs of 4.0 sqmm copper conductor cable, one run of 2.5 sqmm copper conductor and one run of PVC conduit will be measured as one unit.

S&F of Ding dong bell AC, 240 volts single pole complete all as specified and directed.

S&F of ceiling rose surface bakelite two to three terminal complete all as specified and directed.

S&F of Modular Bell push, 6 A, 1 module complete all as specified and directed.

S&F of Modular switch, 1 way, 6 A, 1 module complete all as specified and directed.

S&F of Modular switch, 2 way, 6 A, 1 module complete all as specified and directed.

S&F of Modular switch, 1 way, 16 A, 1 module complete all as specified and directed.

S&F of Modular socket, 6 A, 2/3 pin combined, 2 module complete all as specified and directed.

S&F of Modular socket, 6A/16A, 2/3 pin combined, 2 module complete all as specified and directed.

S&F of Modular fan step regulator, 120 W, 240 volts, 2 module complete all as specified and directed.

S&F of Lamp holder, PVC/ polycarbonate type with back plate with and including 15 Watt LED bulb in white colour with maximum Lumen output (850 lm) and colour temp 3000 K complete all as specified and directed.

S&F of LED lights fitting, 1x 20 W, 220 V, AC decorative box type with driver, holder including LED tube light and connecting up with 1 sqmm three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F of LED light fitting mirror type with high out put diffuser, 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with 1 sqmm three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F of LED light fitting, 10 W bulkhead luminaires including LED light, driver, holder etc and connecting up with 1 sqmm three core flexible copper conductor cable of suitable size complete all as specified and directed.

Taking down Energy meter/Main Switches of any size after disconnecting supply and kept in safe custody & remove the old wooden meter box from site, plastering the existing disturbed wall surface with and including M&L for colour washing and refixing the Meter/Main Switches again on new french polished wooden board of required size as per site and making necessary connections complete all as specified and directed.

S&F in replacement sheet metal enclosures for DB's, TPN, 4 way with 200 Amps rated bus bar, 415 volts, factory made double door flush type, IP-42 protection and all as per IS-8623 and fixed with wall with all accessories including taking down old TPN DB 4 way after disconnecting supply complete all as specified and directed.

S&F in replacement sheet metal enclosures for DB's, SPN, 8 way with 200 Amps rated bus bar, 240 volts, factory made double door flush type, IP-42 protection and all as per IS-8623 and fixed with wall with all accessories including taking down old SPN DB 8 way after disconnecting supply complete all as specified and directed.

S&F of MCB, SP, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 6 to 32 Amps including connection with suitable size aluminium / copper lugs complete all as specified and directed.

S&F of MCB, DP, 240 volts, 10 KA breaking capacity, 'C' curve, of capacity 16 to 40 Amps including connection with suitable size aluminium / copper lugs complete all as specified and directed.

S&F of MCB, TPN, 415 volts, 10 KA breaking capacity, 'C' curve, of capacity 63 Amps including connection with suitable size aluminium / copper lugs complete all as specified and directed.

M&L for earthing complete with galvanised steel plate earth electrode 600 mm X 600 mm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to earthing lead of size 32x6 mm galvanised mild steel wire by means of bolts, nuts, check nuts and washers of galvanised iron from earth plate to test point upto 7.5 metre including all as shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete chamber in cement concrete M15 (Nominal Mix) using 20 mm nominal size coarse aggregate, precast RCC cover slab in cement concrete M-15 (Nominal mix) using 20 mm nominal size coarse aggregate of size 40 cm X 40 cm X 5 cm reinforced with 8 mm dia TMT bars @ 150 mm c/c both ways with one handle for lifting made out of 8 mm dia bar, GI funnel, GI wire mesh filter, 20 mm dia GI pipe medium grade for watering, 20 mm dia GI pipe medium grade for protection of earthing lead, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil/ strata complete all as shown in electrical plate No. 3 of SSR part-I and connected to earthing test point incluidng testing complete all as specified and directed. Note:- (i) Item of earthing includes cost of excavation, removing, PCC Chamber, 15mm bore medium grade GI protection Pipe (7.5 Meters long) for earth lead. (ii) On testing after completion of earthing if the desired earth resistance is not obtained earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of Engr-in Charge.

S&F of LED street light fitting, 35 Watts, 230 V, AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket etc; impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection with and including GI pipe 40 mm dia, light grade for mounting bracket, bent to shape of 1.50 RM length with two Nos MS clamps, nuts, bolts, washers of suitable size complete all as specified and directed.

Suuply and laying in replacement 1100 volts grade heavy duty XLPE cable of size 25 Sqmm, 3.5 core, passing through GI pipe with aluminium conductor stranded polyethylene insulated, conductor served with and including sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed and making necessry connection and testing complete all as specified and directed.

Suuply and laying in replacement 1100 volts grade heavy duty XLPE cable of size 16 Sqmm, 4 core, passing through GI pipe with aluminium conductor stranded polyethylene insulated, conductor served with and including sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed and making necessry connection and testing complete all as specified and directed.

Excavation in trenches in any type of soil (soft loose/ hard dense) not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr in depth and getting out for foundation of pole, laying under ground cables etc and getting out complete all as specified and directed.

M&L for sand filling in trenches for cable cushioning with clean, dry and unwashed sand free from sharp particles including gently punning around cable complete all as specified and directed.

M&L for bricks laid dry in trenches, flat with width equal to length of brick for cable protection well burnt sub class 'B' laid across the cable complete all as specified and directed.

Returning filling in with the earth obtained from excavation including spreading, levelling, watering and well ramming in layers and not exceeding 25 cm in layer complete all as specified and directed.

Removing surplus soil to a distance not exceeding 50 Mtr and deposting where directed at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed.

S&F in replacement GI pipe light grade 50mm dia bore with all fittings and fixed complete to wall, to pole or laid in trenches and road crossing complete all as specified and directed.

M&L for cutting in existing water supply main line in position for insertion of new specials / fittings viz Tee etc. of suitable size upto 25mm bore for making branch connection including testing complete all as specified and directed.

Supply, errecting, testing and commissioning of High Mast pole system consisting of two section suitable for 55 m/s wind speed alongwith head frame, made out of hot dip galvanised steel structure 16 Mtrs long, steel wire rope 6mm dia 97/19 guage, double drum winch, luminiaries carriage suitable for 06 luminiaries in symmetrical arrangement and other accesories manufactured in factory with raising lowering system comprising double drum winch, trailing cable, connector, integral power tool motor, manual handle, junction box, lightining finial, with and including supply of foundation bolts manufactured from special steel along with nuts, washers, anchor plate and common template and outdoor stand mounted feeder pillar with 32 A, TPN, MCB incomer, single dial time switch, 25A TP contactor for the automatic switching of luminiaries and timer switch with all connected accessories for automatic switching of light, power tool control with 2 Nos, 9 A contactors and raise lower push button, incoming 25 sq. mm and out going 2.5 sq. mm terminals with all connected items as required at site complete all as specified and directed with and including following specifications:- Notes: (i) High mast pole system shall be of Make: Bajaj/ GE/ Crompton/ Philips/ Havells as approved by GE. (ii) The cost of aviation light, feeder piller box, copper cable 2.5 Sqmm from feeder piller box to LED light is deemed to be included in the quoted rate. (iii) The cost for excavation in fdn, returning fillingin, RCC foundation etc. shall be born by the contractor and design should be as per manufacturer recommendations & no extra amount will be paid to the contractor on this account.

HIGH MAST SYSTEM Height of mast : 16 Meter No. of Section : Two Material Construction : S355 Grade as per IS 2062/BS-EN10 025 Base dia and top diameter (A/F) : Top : 150mm & Botton : 460 mm Cross section of Mast : 20 side polygon Standard for Galvanisation : A per BS EN ISO 1461 Size of Opening and door at base : 1200 x 2500 mm Diameter of base plate : 570 mm Thickness of base plate : 25 mm Lighting protection finial : GI single spike of length 1200mm Max. wind speed : 55m/s as per IS 875 (Part III) Number of foundation bolts : 12 Nos PCD of foundation bolts : 590 mm Type / diameter / length of foundation bolts : TS 600/30mm dia/ 850 mm long

LUMINAIRES CARRIAGE Material of construction : 50 NB ERW Class B-M.S Pipe Diameter of carriage ring (mm) : 535 mm (ID) Construction : 08 Arm, Welded, 2 Sections Load carrying capacity : 16 Luminaire

TRAILING CABLE Conductor : Copper, 6 core, 2.5 Sqmm Insulation : PVC Flexible No.of circuits per mast : One No cable per mast

WINCH / POWDER TOOL Type /SWL of winch : Double drum, SWL 750 Kg Method of Operation : Integral Motor Motor Capacity : 1.0 HP ( Including suitable starter) No of Speeds : 6 Pole, Single speed Torque Limitor : With Mechanical Tripping Facility

STAINLESS STEEL WIRE ROPE Grade / construction : AISI 316, 7/19 Construction Number of Ropes : Two Continuous Diameter (mm) : 6 mm, 97/19 guage, Breaking load Capacity : 2350 Kg x 2

S&F of LED flood light 250 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant including driver and lamp complete all as specified and directed.

M&L for earthing with galvanised iron earth plate electrode 600x600x6mm size buried directly in ground vertically at a depth not less than 2.25 M below ground level with the top edge of earth plate at a depth not less than 1.50 M below ground level, connected to Galvanized steel strip 25x4mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised steel, earth plate electrode surrounded by a packed thickness of char coal or coke dust mixed with common salt in alternate layers not exc. 150 mm thick, strip protected with and including galvanised iron pipe 40 mm bore, light grade, RCC pit and CI cover with frame duly grouted with PCC incl necessary excavation, returning, filling in and removal of surplus spoil upto a distance of 50.00 M complete all as shown in Electrical Plate No. 5 of MES Schedule Part-I including testing on completion complete all as specified and directed.

S&F of laying GI tubing light grade of size 40mm for cable protection on road/drain/floor/pole including necessary clamps 40mm x 4mm complete all as specified and directed

Deduct Schedule of credit (calculation will be done off line) Rs. 63708.00

pyarelal galar (BID ID -3194523)

TANUJ CONST. CO. (BID ID -3197798)

SULTAN SINGH, CONTRACTOR (BID ID -3194781)

PK CONSULTANT (BID ID -3192144)

M/S HARSH VIKAS GALAR ENGINEERING (BID ID -3192691)