Upgradation of Infrastructure Development for EMRS Tamenglong, Manipur.

Amount

SUB-HEAD ; BOY'S HOSTEL WITH KITCHEN CUM DINNING HALL ;

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sandy soil under floors including, watering,ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level: a) 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 50 mm thick with cement concrete. (a) 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Extra for providing and mixing water proofing materials in cement concrete work 1 kg per 50 kg of cement.

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate of 20 mm nominal size) i/c finishing the top surface of concrete smooth.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. UPTO PLINTH

Concrete of M-25 grade with minimum cement content of 330 kg/cum.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto Plinth level. ABOVE PLINTH

Concrete of M-25 grade with minimum cement content of 330 kg/cum.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.

a) Thermo-Mechanically Treated bars.

Centering and shuttering including strutting, propping etc. and removal of form for:

a) Foundations, footings, bases of columns, etc. for mass concrete.

b) Lintels, beams, plinth beams, girders, bressumers and cantilevers.

c) Suspended floors, roofs, landings, balconies and access platform.

d) Columns, Pillars, Piers, Abutments, Posts and Struts.

e) Staircase with sloping or stepped, soffits i/c risers and stringes e/c landing.

Brick work with Ist class common burnt clay F.P.S. (non modular) bricks in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with Ist class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1 : 3 (1 cement : 3 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames,wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for separately :Local best quality Teak wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Local best quality Teak wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10 x 15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :75x65x4 mm (heavy type)

Providing and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass handles with screws etc. complete : 125 mm

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08% and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of stepts , over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.

Sizes of Tiles 600x600 mm (double charged)Branded

Marble stone flooring with 18mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with : a) Raj Nagar plain

Tile work in skirting, risers of steps and dado (upto 2 m height) over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with pigment of matching shade complete.Mable tiles (polished ) Raj Nagar.

Extra for prefinished nosing to treads of steps of marble stone.

12 mm cement plaster 1:4 (1 cement:4 fine sand).

12 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1:3 ( 1 cement : 3 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade

New work (two or more coats) over and including priming coat with cement primer:-

Finishing walls with water proofing cement paint of required shade : New work ( Two or more coats applied @3.84 kg/10 sqm)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer

Providing and applying white cement based putty of average thickness 1mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coat:-With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

INTERNAL WATER SUPPLY AND SANITARY INSTALATION :

CHLORINATED POLYVINYL CHLORIDE (CPVC) pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. including cutting chases and making good the walls etc.External work a) 50mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work -Conceal work a).32mm dia

SANITARY FITTINGS COMPLETE

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: a).White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: a).W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: a).White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : a).One urinal basin with 5 litre white P.V.C. automatic flushing cistern

BRASS AND CP BRASS FITTINGS

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : a) 15 mm nominal bore

Providing and fixing brass stop cock of approved quality. a) 15 mm diameter

Providing and fixing Water Storage Tanks with 400 mm diameter nominal base G.I. overflow tube 25 mm nominal G.I. inlet and 15 mm nominal G.I. outlet tube i/c hoisting a height of 10 m above ground level. a) 2000 litres net capacity storage tanks

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing : a) Rectangular shape 453x357 mm

Providing and fixing PTMT towel ring trapezoidal shape 215mm long, 200mm wide with minimum distances of 37mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing C.P. brass toilet paper holder

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

SH:-PVC Pipes and Fitting

Providing and fixing PVC soil ,waste and vent pipes.External a).100mm dia

Providing and fixing PVC vent cowl.a).100mm dia

Providing and fixing MS holder bat clamps of approved design to 100 mm HCI pipe socket i/c cost of cutting holes and making good the walls etc. including cost of cutting holes and making good the walls etc.

Providing and fixing PVC soil ,waste and vent pipes. a) 75mm dia

Providing and fixing PVC NAHANI TRAP. a) 75mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.A).Flexible pipe--32 mm dia

Supply and installation of water pump Tulu (Texmo) 1HP of approved quality.

SEPTIC TANK

Earthwork in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms lift upto 1.5metres including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres. All kinds of soil.

Filling available excavated earth(excluding rock) in trenches,plinth sides of foundation etc. in layers not exceeding 20 cm in depth,consolidating each deposited layer by ramming and watering lead upto 50 metres lift upto 1.5 metre

P/L cement concrete in foundation and plinth excluding the cost of centering and shuttering in 1:4:8(1 cement: 4course sand: 8 graded stone aggregate 40mm. nominal size

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto Plinth level. Concrete of M-25 grade with minimum cement content of 330 kg/cum. All works upto Plinth level.

Concrete of M-25 grade with minimum cement content of 330 kg/cum.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto Plinth level. Concrete of M-25 grade with minimum cement content of 330 kg/cum. All works upto Plinth level.

Concrete of M-25 grade with minimum cement content of 330 kg/cum.

Steel reinforcement for R.C.C work including straightening,cutting, bending, placing in position and binding all complete.a)Thermo mechanically treated bars

Providing form works i/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for in-situ reinforced concrete and plain concrete work in

(a) Foundation, footing, bases of columns etc. and mass concrete.

b) Suspended floors, roofs, landings, balconies and access platform.

c) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Providing and fixing C.I. Cover frame (for manhole and chambers).a).600 mm x 450 mm (heavy duty)

INTERNAL ELECTRICFICATION ISTALATION (IEI).

Wiring for light/fan point/Exhaust fan point/ call bell point with 1.5 mm2 PVC insulated copper conductor single core cable inPVC casing & capping with modular type switch,modular plate size,G.I. box and earthing the point with 1.5 mm2 PVC insulated copper conductor single core cable etc. as reqd.

1. Group A

2. Group B

3. Group C

Wiring for light point/power plug with 2x4 mm2 PVC insulated copper conductor single core cable in PVC casing & capping along with 1 no. 4mm2 PVC insulated copper conductor single core cable for loop earthing etc. as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) PVC insulated conductor single core cable in PVC casing & capping etc.as reqd.

(a) 2X1.5mm2+1X1.5mm2 earth wire

(b) 2X2.5mm2+1X2 .5mm2 earth wire

(c) 2X4mm2+1X4mm2 earth wire

(d)2X6mm2+2X6mm2 earth wire

(e) 2X10mm2+2X10mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing modular plate and switch box i/c connection but excluding modular plate etc as reqd.

(a) 5/6 amps switch

(b) 15/16 amps switch

(c) 3 pin 5/6 amps socket outlet

(d) 6 pin 15/16 amps socket outlet

S/F 25 amp Air-conditioner power plug point i/c 4 modules metal box on surface or in recess 4-modules plate and cover in front,25 amp modular starter 25 amp modular socket outlet and 25 amp plug i/c connection etc as reqd.

S/F stepped type electronic fan regulator on the existing modular plate switch box i/c connection but excluding modular plate etc.

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/lsolator) (a) 16 way double door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

S/F (following rating) double pole 240V isolator in the existing MCB DB complete with connection,testing and commissioning as reqd. (a) 63 amp

Earthing with copper plate 600x600xmm thick i/c accessories and providing masonary enclosure with copper plate having locking arrangement and watering pipes etc.(but without charcoal and salt complete as reqd.)

Extra for using salt and charcoal for G.l.plates or copper plate earth electrode as reqd.

P/L earth connection from earth electrode with 4mm dia copper in 15 mm dia GI pipe as reqd.

S/F 48" sweep AC ceiling fan complete with down rod, canopy 3 (three) blades but without regulator etc as reqd. (make Bajaj/Usha or similar)

S/F 12"(305mm) dia light duty exhaust fan complete with all accessories i/c connection etc as reqd.

S/F Recess mounting LED down lighters BGSL 0101WH, 220223, cast aluminium housing, fixed with collimated lens, 1x1W white LED mounted on MCPCB, extruded Al. Heat sink spring loaded mounting clips comlplete with connection etc. As reqd.

S/F 2 tone capacity split type air conditioner, (Diamond 3 star,5 G30,G-SC 24 FD 3WJH) complete with indo voltage Stabilizer, Automatic 5 KVA (140-280 for 2 ton)

Supply, Installation, Testing & Commissioning of LT Panel , cubicle type, made out of 2mm thick CRCA sheet,totally enclosed, IP 42, free standing, floor mounting, dust and vermin proof, indoor, compartmentalised, suitable for operation on 3 phase , 415 V, 50Hz AC system with busbars, including internal wiring with suitable size HFFR wires/cable, interconnection, duly powder coated with seven tank process etc., including all inter connections and following components as per drawing and technical specifications. INCOMER 200 A FP 125kA MCCB with adjustable thermal magnetic release with OL & SC protection - 2 nos. BUSBARS 200 Ampere TPN busbars of Aluminum alloy high conductivity with heat shrinkable coloured sleeves INSTRUMENTS Digital type multifunction meter with CTs of suitable rating for measurement of voltage, current, frequency, power factor, KVA, KW, KWH. - 1 No ON/OFF indication lamps-1set RYB Indicating lamps LED type - 3 Nos. OUTGOINGS 100A FP. 125kA MCCB with adjustable thermal magnetic release with OL & SC protection - 4 nos. 100A/63A FP 25kA MCCB with thermal magnetic release with OL & SC protection - 6 nos.

External Electrification Installation & Fire Fighting

Distribution transformer 250kva

9m Steel Tubular poles (410 SP-3 l)

Channe I 1 00X5 0.@,7 .9 Ke/ m 2.8X2 for supporting Transformer

Channel 100X50,@7.9 Kflm2.8X2 for D.P. X-arm

Channel 100X50.@7 .9 Kelm 0 .46X2 for supporting of item 3

Channel 75X40,@5.7Kglm2X2.8m for HG fuse unit & A.B. switch

Channel 75X40,@5.7Kglm2Xl.0m A.B. switch main chamel X-arm.

Channel 75X40,@5.7Kglm 2X0.5m for supporting H.G. fuse main channel Xarrn

Angle (50X50X6)mm 2.8X2 @ 4.5 Kg/m transformer belting and Angle (35X35X5),0 .46X2 @ 2.6 K!m. Transformer belting support.

Clamp for transformer base channel for M.S. flat [email protected]/m 027nX2.

Clamp for A.B. switch bracing 50X8mm @ 3.lKflm 0.23mX2:0.46m.

Clamp for HG Fuse Bracing for MS Flat 50x8mm @3.1K91m,023nx2

11KV A.B.Switch 200 Amp

Horn gap fuse unit/D.O. fuse

D.B.box with complete accessories with Kit-Kat

D.B.box cross ann of M.S. Angle 35X35X5mm @2.6Kg1m2.8X2:5.6m

Sub-Station Fencing

Sub-Station Earthing

Danger board.

I I KV Liehtning Arrester

Earthing set complete with G.I. wire

Bolts,Nuts,clamps etc. (5/8)" x 3"- 8 Kg) & (5/8)" x 8.5"- 8 Kg)

Pole muffing

Pole painting

Single Core XLPE Unarmoured Cable 240 sq.mm

Thimble 240 sq.mm (4x4 no.)

Thimble 50 sq.mm

Erection Charge (Inclusive of Transportation & Handling Charge)

Earthing with copper earth plate 600mmx600mmx6mm thick lc accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) as reqd.

Extra for using salt and charcoal for G.t. or copper plate earth electrode as reqd.

P/F 25mmx5mm copper strip in 40mm dia G.I. pipe from earth electrode as reqd

P / L earth connection from earth electrode with 10mm dia copper wire in 20mm dia G.L pipe as reqd

P/F earth bus of 32mmx6mm copper strip on surface for connection etc. as reqd.

Providing and Fixing of lightning conductor finial made of 25mm dia 300mm long copper tube having single prong at top with 85mm dia 3mm thick copper plate Uc holes etc. complete as reqd.

Fixing of lightning conductor finial of 25mm dia 300mm long copper /G.I. tube having single prong at top with 85mm dia 3mm thick base plate i/c hole etc. as reqd.

P/L copper tape 32mmx6mm from earth electrode directly in ground as reqd

Supply of 50 sq.mm 4 core PVC/xLPE insulated heavy duty armoured cable 1.1KV grade

Laying of 1 no. PVC insulated PVC sheathed power cable of l.lKV grade of size not less than 25fin0 but not exceeding l20mm2 direct in ground i/c excavation, sand cushioning, protective covering and re-filling the trench etc. as reqd.

Erection of steel tubular pole of length not less than l0 mtrs but not exceeding 12 mtrs. in cement concrete l:3:6 (l cement:3 coarse sand :6 graded stone agff. 40mm nominal size) foundation i./c excavation & refilling etc. as reqd.

Single piece cast Al. with full glass cover integral luminaries (IP66) HPSV-7OW grcy powder coated dia-cast Al' housing complete with all accessorie

S/F 35 ltr water heater (Geyser) A.C. 2 Kw vertical type with all accessories , ( 150581 SKT - PLUS 35L)ilc coirnection etc as reqd

S/F 400W 240V HPMV lamp

S/F 400W 240V HPMV lamp ballast

S/F igniter for HPSV-2 lamp

600mm x 600mm x 3mm thick (10.5kg) copper plate

25mm x 5mm copper tape (1.15kg/mtr)

40 mm to 20 mm reducer

Charcoal

2.24 mm dia bare aluminium earth wire

Lightning ftnial,25 mm diaX 300 mm long copper

P/L earth connection from earth electrode with 4mm dia copper wire in 15mm dia GI pipe as reqd.

P/F 50mmx6mm copper strip in 80mm dia G.I. pipe from earth electrode as reqd

Cement Concrete Earthing Pit Cover

Earth strip falls

Testing link with bolted connection

Incomer 400 A, 25 kA MCCB with adjusable thermal magnetic release with O/L & SC protection with Aluminium busbar with heat skrinkablw coloured sleeves with digital type multiuction meter with CTs suitabl raing with following Outgoing

63 A MCCB 25k thermal Magnetic based with O/L & S/C Protection Release

Fire Fighting

Providing and Fixing of fire fighting system

Supply and installation of ABC type fire extinguisher 4 kg

Supply and installation of CO2 type fire extinguisher

Fire Hose reels

Sprinkler main pipe 150ø

Pendent Sprinklers

Sprinkler Branch pipe 20ø

Sprinkler Branch pipe 25ø

Sprinkler Branch pipe 32ø

Sprinkler Branch pipe 40ø

Sprinkler Branch pipe 50ø

Sprinkler Branch pipe 65ø

Sprinkler Branch pipe 80ø

Fire Sprinkler Alarm Valve With Water Motor Gong

Siren

Data gathering fire alarm panel

Manual call point (MCP)

Exit Sign

Addressable fire alarm hooter with strobe light

Junction box (JB-01-01-1/02)

Intelligent multi sensor detecor on true ceiling

Fault isolator

Control modular

2p x 1.5 sqmmTwisted pair PVC insulated armoured FRLS Cable

3C x 2.5 sqmm PVC insulated armoured FRLS cable

SUB-HEAD ; GIRLS HOSTEL WITH KITCHEN CUM DINNING HALL.

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sandy soil under floors including, watering,ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level: a) 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 50 mm thick with cement concrete.(a). 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Extra for providing and mixing water proofing materials in cement concrete work 1 kg per 50 kg of cement.

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate of 20 mm nominal size) i/c finishing the top surface of concrete smooth.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. UPTO PLINTH

Concrete of M-25 grade with minimum cement content of 330 kg/cum.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but e/c the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto Plinth level. ABOVE PLINTH

Concrete of M-25 grade with minimum cement content of 330 kg/cum.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.

a) Thermo-Mechanically Treated bars.

Centering and shuttering including strutting, propping etc. and removal of form for:

a) Foundations, footings, bases of columns, etc. for mass concrete.

b) Lintels, beams, plinth beams, girders, bressumers and cantilevers.

c) Suspended floors, roofs, landings, balconies and access platform.

d) Columns, Pillars, Piers, Abutments, Posts and Struts.

e) Staircase with sloping or stepped, soffits i/c risers and stringes excluding landing.

Brick work with Ist class common burnt clay F.P.S. (non modular) bricks in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with Ist class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1 : 3 (1 cement : 3 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames,wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for separately :Local best quality Teak wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Local best quality Teak wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10 x 15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :75x65x4 mm (heavy type)

Providing and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass handles with screws etc. complete : 125 mm

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08% and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of stepts , over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.

Sizes of Tiles 600x600 mm (double charged)Branded

Marble stone flooring with 18mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with : a) Raj Nagar plain

Tile work in skirting, risers of steps and dado (upto 2 m height) over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with pigment of matching shade complete.Mable tiles (polished ) Raj Nagar.

Extra for prefinished nosing to treads of steps of marble stone.

12 mm cement plaster 1:4 (1 cement:4 fine sand).

12 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1:3 ( 1 cement : 3 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade

New work (two or more coats) over and including priming coat with cement primer:-

Finishing walls with water proofing cement paint of required shade : New work ( Two or more coats applied @3.84 kg/10 sqm)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer

Providing and applying white cement based putty of average thickness 1mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coat:-With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

CHLORINATED POLYVINYL CHLORIDE (CPVC) pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. including cutting chases and making good the walls etc.External work a) 50mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work -Conceal work a).32mm dia

SANITARY FITTINGS COMPLETE

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: a).White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: a).W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: a).White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : a).One urinal basin with 5 litre white P.V.C. automatic flushing cistern

BRASS AND CP BRASS FITTINGS

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :a).15 mm nominal bore

Providing and fixing brass stop cock of approved quality. ( a).15 mm diameter

Providing and fixing Water Storage Tanks with 400 mm diameter nominal base G.I. overflow tube 25 mm nominal G.I. inlet and 15 mm nominal G.I. outlet tube i/c hoisting a height of 10 m above ground level. a) 2000 litres net capacity storage tanks

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing : a) Rectangular shape 453x357 mm

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing C.P. brass toilet paper holder

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

SH:-PVC Pipes and Fitting

Providing and fixing PVC soil ,waste and vent pipes.External a).100mm dia

Providing and fixing PVC vent cowl. a).100mm dia

Providing and fixing MS holder bat clamps of approved design to 100 mm HCI pipe socket i/c cost of cutting holes and making good the walls etc. including cost of cutting holes and making good the walls etc.

Providing and fixing PVC soil ,waste and vent pipes.a).75mm dia

Providing and fixing PVC NAHANI TRAP.a).75mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.A).Flexible pipe-32 mm dia

Supply and installation of water pump Tulu(Texmo) 1HP of approved quality.

SEPTIC TANK

Earthwork in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms lift upto 1.5metres including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres. All kinds of soil.

Filling available excavated earth(excluding rock) in trenches,plinth sides of foundation etc. in layers not exceeding 20 cm in depth,consolidating each deposited layer by ramming and watering lead upto 50 metres lift upto 1.5 metre

P/L cement concrete in foundation and plinth excluding the cost of centering and shuttering in 1:4:8(1 cement: 4course sand: 8 graded stone aggregate 40mm. nominal size

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto Plinth level. Concrete of M-25 grade with minimum cement content of 330 kg/cum. All works upto Plinth level.

Concrete of M-25 grade with minimum cement content of 330 kg/cum.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto Plinth level. Concrete of M-25 grade with minimum cement content of 330 kg/cum. All works upto Plinth level.

Concrete of M-25 grade with minimum cement content of 330 kg/cum.

Steel reinforcement for R.C.C work including straightening,cutting, bending, placing in position and binding all complete.a)Thermo mechanically treated bars

Providing form works i/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for in-situ reinforced concrete and plain concrete work in

(a) Foundation, footing, bases of columns etc. and mass concrete.

b) Suspended floors, roofs, landings, balconies and access platform.

c) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Providing and fixing C.I. Cover frame (for manhole and chambers).a).600 mm x 450 mm (heavy duty)

INTERNAL ELECTRIFICATION INSTALATION ;

Wiring for light/fan point/Exhaust fan point/ call bell point with 1.5 mm2 PVC insulated copper conductor single core cable inPVC casing & capping with modular type switch,modular plate size,G.I. box and earthing the point with 1.5 mm2 PVC insulated copper conductor single core cable etc. as reqd.

1. Group A

2. Group B

C. Group C

Wiring for light point/power plug with 2x4 mm2 PVC insulated copper conductor single core cable in PVC casing & capping along with 1 no. 4mm2 PVC insulated copper conductor single core cable for loop earthing etc. as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) PVC insulated conductor single core cable in PVC casing & capping etc.as reqd.

(a) 2X1.5mm2+1X1.5mm2 earth wire

(b) 2X2.5mm2+1X2 .5mm2 earth wire

(c) 2X4mm2+1X4mm2 earth wire

(d)2X6mm2+2X6mm2 earth wire

(e) 2X10mm2+2X10mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing modular plate and switch box i/c connection but excluding modular plate etc as reqd.

(a) 5/6 amps switch

(b) 15/16 amps switch

(c) 3 pin 5/6 amps socket outlet

(d) 6 pin 15/16 amps socket outlet

S/F 25 amp Air-conditioner power plug point i/c 4 modules metal box on surface or in recess 4-modules plate and cover in front,25 amp modular starter 25 amp modular socket outlet and 25 amp plug i/c connection etc as reqd.

S/F stepped type electronic fan regulator on the existing modular plate switch box i/c connection but excluding modular plate etc.

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/lsolator) (a) 16 way double door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

S/F (following rating) double pole 240V isolator in the existing MCB DB complete with connection,testing and commissioning as reqd. (a) 63 amp

Earthing with copper plate 600x600xmm thick i/c accessories and providing masonary enclosure with copper plate having locking arrangement and watering pipes etc.(but without charcoal and salt complete as reqd.)

Extra for using salt and charcoal for G.l.plates or copper plate earth electrode as reqd.

P/L earth connection from earth electrode with 4mm dia copper in 15 mm dia GI pipe as reqd.

S/F 48" sweep AC ceiling fan complete with down rod, canopy 3 (three) blades but without regulator etc as reqd. (make Bajaj/Usha or similar)

S/F 12"(305mm) dia light duty exhaust fan complete with all accessories i/c connection etc as reqd.

S/F Recess mounting LED down lighters BGSL 0101WH, 220223, cast aluminium housing, fixed with collimated lens, 1x1W white LED mounted on MCPCB, extruded Al. Heat sink spring loaded mounting clips comlplete with connection etc. As reqd.

S/F 2 tone capacity split type air conditioner, (Diamond 3 star,5 G30,G-SC 24 FD 3 WJH ) complete with indo voltage Stabilizer,Automatic 5 KVA (140-280 for 2 ton)

Supply, Installation, Testing & Commissioning of LT Panel , cubicle type, made out of 2mm thick CRCA sheet,totally enclosed, IP 42, free standing, floor mounting, dust and vermin proof, indoor, compartmentalised, suitable for operation on 3 phase , 415 V, 50Hz AC system with busbars, including internal wiring with suitable size HFFR wires/cable, interconnection, duly powder coated with seven tank process etc., including all inter connections and following components as per drawing and technical specifications. INCOMER 200 A FP 125kA MCCB with adjustable thermal magnetic release with OL & SC protection - 2 nos. BUSBARS 200 Ampere TPN busbars of Aluminum alloy high conductivity with heat shrinkable coloured sleeves INSTRUMENTS Digital type multifunction meter with CTs of suitable rating for measurement of voltage, current, frequency, power factor, KVA, KW, KWH. - 1 No ON/OFF indication lamps -1set RYB Indicating lamps LED type - 3 Nos. OUTGOINGS 100A FP. 125kA MCCB with adjustable thermal magnetic release with OL & SC protection - 4 nos. 100A/63A FP 25kA MCCB with thermal magnetic release with OL & SC protection - 6 nos.

External Electrification Installation & Fire Fighting

Distribution transformer 250kva

9m Steel Tubular poles (410 SP-3 l)

Channe I 1 00X5 0.@,7 .9 Ke/ m 2.8X2 for supporting Transformer

Channel 100X50,@7.9 Kflm2.8X2 for D.P. X-arm

Channel 100X50.@7 .9 Kelm 0 .46X2 for supporting of item 3

Channel 75X40,@5.7Kglm2X2.8m for HG fuse unit & A.B. switch

Channel 75X40,@5.7Kglm2Xl.0m A.B. switch main chamel X-arm.

Channel 75X40,@5.7Kglm 2X0.5m for supporting H.G. fuse main channel Xarrn

Angle (50X50X6)mm 2.8X2 @ 4.5 Kg/m transformer belting and Angle (35X35X5),0 .46X2 @ 2.6 K!m. Transformer belting support.

Clamp for transformer base channel for M.S. flat [email protected]/m 027nX2.

Clamp for A.B. switch bracing 50X8mm @ 3.lKflm 0.23mX2:0.46m.

Clamp for HG Fuse Bracing for MS Flat 50x8mm @3.1K91m,023nx2

11KV A.B.Switch 200 Amp

Horn gap fuse unit/D.O. fuse

D.B.box with complete accessories with Kit-Kat

D.B.box cross ann of M.S. Angle 35X35X5mm @2.6Kg1m2.8X2:5.6m

Sub-Station Fencing

Sub-Station Earthing

Danger board.

I I KV Liehtning Arrester

Earthing set complete with G.I. wire

Bolts,Nuts,clamps etc. (5/8)" x 3"- 8 Kg) & (5/8)" x 8.5"- 8 Kg)

Pole muffing

Pole painting

Single Core XLPE Unarmoured Cable 240 sq.mm

Thimble 240 sq.mm (4x4 no.)

Thimble 50 sq.mm

Erection Charge (Inclusive of Transportation & Handling Charge)

Earthing with copper earth plate 600mmx600mmx6mm thick lc accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) as reqd.

Extra for using salt and charcoal for G.t. or copper plate earth electrode as reqd.

P/F 25mmx5mm copper strip in 40mm dia G.I. pipe from earth electrode as reqd

P / L earth connection from earth electrode with 10mm dia copper wire in 20mm dia G.L pipe as reqd

P/F earth bus of 32mmx6mm copper strip on surface for connection etc. as reqd.

Providing and Fixing of lightning conductor finial made of 25mm dia 300mm long copper tube having single prong at top with 85mm dia 3mm thick copper plate Uc holes etc. complete as reqd.

Fixing of lightning conductor finial of 25mm dia 300mm long copper /G.I. tube having single prong at top with 85mm dia 3mm thick base plate i/c hole etc. as reqd.

P/L copper tape 32mmx6mm from earth electrode directly in ground as reqd

Supply of 50 sq.mm 4 core PVC/xLPE insulated heavy duty armoured cable 1.1KV grade

Laying of 1 no. PVC insulated PVC sheathed power cable of l.lKV grade of size not less than 25fin0 but not exceeding l20mm2 direct in ground i/c excavation, sand cushioning, protective covering and re-filling the trench etc. as reqd.

Erection of steel tubular pole of length not less than l0 mtrs but notexceeding 12 mtrs. in cement concrete l:3:6 (l cement:3 coarse sand :6 graded stone agff. 40mm nominal size) foundation i./c excavation & refilling etc. as reqd.

Single piece cast Al. with full glass cover integral luminaries (IP66) HPSV-7OW grcy powder coated dia-cast Al' housing complete with all accessorie

S/F 35 ltr water heater (Geyser) A.C. 2 Kw vertical type with all accessories , ( 150581 SKT - PLUS 35L)ilc coirnection etc as reqd

S/F 400W 240V HPMV lamp

S/F 400W 240V HPMV lamp ballast

S/F igniter for HPSV-2 lamp

600mm x 600mm x 3mm thick (10.5kg) copper plate

25mm x 5mm copper tape (1.15kg/mtr)

40 mm to 20 mm reducer

Charcoal

2.24 mm dia bare aluminium earth wire

Lightning ftnial,25 mm diaX 300 mm long copper

P/L earth connection from earth electrode with 4mm dia copper wire in 15mm dia GI pipe as reqd.

P/F 50mmx6mm copper strip in 80mm dia G.I. pipe from earth electrode as reqd

Cement Concrete Earthing Pit Cover

Earth strip falls

Testing link with bolted connection

Incomer 400 A, 25 kA MCCB with adjusable thermal magnetic release with O/L & SC protection with Aluminium busbar with heat skrinkablw coloured sleeves with digital type multiuction meter with CTs suitabl raing with following Outgoing

63 A MCCB 25k thermal Magnetic based with O/L & S/C Protection Release

Fire Fighting

Providing and Fixing of fire fighting system

Supply and installation of ABC type fire extinguisher 4 kg

Supply and installation of CO2 type fire extinguisher

Fire Hose reels

Sprinkler main pipe 150ø

Pendent Sprinklers

Sprinkler Branch pipe 20ø

Sprinkler Branch pipe 25ø

Sprinkler Branch pipe 32ø

Sprinkler Branch pipe 40ø

Sprinkler Branch pipe 50ø

Sprinkler Branch pipe 65ø

Sprinkler Branch pipe 80ø

Fire Sprinkler Alarm Valve With Water Motor Gong

Siren

Data gathering fire alarm panel

Manual call point (MCP)

Exit Sign

Addressable fire alarm hooter with strobe light

Junction box (JB-01-01-1/02)

Intelligent multi sensor detecor on true ceiling

Fault isolator

Control modular

2p x 1.5 sqmmTwisted pair PVC insulated armoured FRLS Cable

3C x 2.5 sqmm PVC insulated armoured FRLS cable

SUB-HEAD ; STAFF QUARTER BLOCK -1

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sandy soil under floors including, watering,ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level: a) 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 50 mm thick with cement concrete.(a). 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Extra for providing and mixing water proofing materials in cement concrete work 1 kg per 50 kg of cement.

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate of 20 mm nominal size) i/c finishing the top surface of concrete smooth.

Providing and laying in position ready mix plain cement concrete or site batched design mix cement concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana/ordinary portland/portland slag cement, admixture in recommended proportion as per IS 9103 to accelerate/retard setting of concrete, to improve ductility and workability without impairing strength, including pumping of concrete to site of laying, curing, carriage of all leads, but excluding the cost of centering, shuttering, finishing and reinforcements as per direction of engineer in charge, for the following grades of concrete.All works upto plinth level

Concrete of M25 grade with minimum cement content of 330 kg/cum

Providing and laying in position ready mix plain cement concrete or site batched design mix cement concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana/ordinary portland/portland slag cement, admixture in recommended proportion as per IS 9103 to accelerate/retard setting of concrete, to improve ductility and workability without impairing strength, including pumping of concrete to site of laying, curing, carriage of all leads, but excluding the cost of centering, shuttering, finishing and reinforcements as per direction of engineer in charge, for the following grades of concrete. All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of 330 kg/cum

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.

.a) Thermo-Mechanically Treated bars.

Centering and shuttering including strutting, propping etc. and removal of form for:

a) Foundations, footings, bases of columns, etc. for mass concrete.

b) Lintels, beams, plinth beams, girders, bressumers and cantilevers.

c) Suspended floors, roofs, landings, balconies and access platform.

d) Columns, Pillars, Piers, Abutments, Posts and Struts.

e) Stairs, (excluding landings) except spiral-staircases.

Brick work with Ist class common burnt clay F.P.S. (non modular) bricks in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with Ist class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1 : 3 (1 cement : 3 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames,wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for separately :Local best quality Tolhao wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Local best quality Tolhao wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10 x 15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :75x65x4 mm (heavy type)

Providing and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass handles with screws etc. complete : 125 mm

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing in position collapsible steel shutters with vertical channels 20xl0x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia, steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and laying rectified Glazed Ceramic floor tiles 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS :15622 of approved make in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08% and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of stepts , over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.

Sizes of Tiles 600x600 mm (double charged)Branded

Marble stone flooring with 18mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with : a) Raj Nagar plain

Tile work in skirting, risers of steps and dado (upto 2 m height) over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with pigment of matching shade complete.Mable tiles (polished ) Raj Nagar.

Extra for prefinished nosing to treads of steps of marble stone.

12 mm cement plaster 1:4 (1 cement:4 fine sand).

15 mm cement plaster on rough side of single or half brick wall mix : 1:4( 1 cement : 4 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade

New work (two or more coats) over and including priming coat with cement primer:-

Finishing walls with water proofing cement paint of required shade : New work ( Two or more coats applied @3.84 kg/10 sqm)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer

Providing and applying white cement based putty of average thickness 1mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coat:-With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

SANITARY FITTINGS COMPLETE

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: a).White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: a).W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: a).White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : a).One urinal basin with 5 litre white P.V.C. automatic flushing cistern

BRASS AND CP BRASS FITTINGS

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :a).15 mm nominal bore

Providing and fixing brass stop cock of approved quality. a).15 mm diameter

Providing and fixing Water Storage Tanks with 400 mm diameter nominal base G.I. overflow tube 25 mm nominal G.I. inlet and 15 mm nominal G.I. outlet tube i/c hoisting a height of 10 m above ground level. a).2000 litres net capacity storage tanks

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing : a) Rectangular shape 453x357 mm

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing C.P. brass toilet paper holder

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

SH:-PVC Pipes and Fitting

Providing and fixing PVC soil ,waste and vent pipes.External a).100mm dia

Providing and fixing PVC vent cowl.a).100mm dia

Providing and fixing MS holder bat clamps of approved design to 100 mm HCI pipe socket i/c cost of cutting holes and making good the walls etc. including cost of cutting holes and making good the walls etc.

Providing and fixing PVC soil ,waste and vent pipes.a).75mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.A).Flexible pipe--32 mm dia

Supply and installation of water pump Tulu(Texmo) 1HP of approved quality.

INTERNAL ELCTRIFICATION INSTALLATION

Wiring for light/fan point/Exhaust fan point/ call bell point with 1.5 mm2 PVC insulated copper conductor single core cable inPVC casing & capping with modular type switch, modular plate size,G.I. box and earthing the point with 1.5 mm2 PVC insulated copper conductor single core cable etc. as reqd.

1. Group A

2. Group B

C. Group C

Wiring for light point/power plug with 2x4 mm2 PVC insulated copper conductor single core cable in PVC casing & capping along with 1 no. 4mm2 PVC insulated copper conductor single core cable for loop earthing etc. as reqd.

INTERNAL ELCTRIFICATION INSTALLATIONWiring for circuit/Sub-main wiring with earth wire with (the following sizes of) PVC insulated conductor single core cable in PVC casing & capping etc.as reqd.

(a) 2X1.5mm2+1X1.5mm2 earth wire

(b) 2X2.5mm2+1X2 .5mm2 earth wire

(c) 2X4mm2+1X4mm2 earth wire

(d)2X6mm2+2X6mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing modular plate and switch box i/c connection but excluding modular plate etc as reqd.

(a) 5/6 amps switch

(b) 15/16 amps switch

(c) 3 pin 5/6 amps socket outlet

(d) 6 pin 15/16 amps socket outlet

S/F stepped type electronic fan regulator on the existing modular plate switch box i/c connection but e/c modular plate etc.

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/lsolator) (a) 16 way double door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

S/F (following rating) double pole 240V isolator in the existing MCB DB complete with connection,testing and commissioning as reqd. (a) 63 amp

Earthing with copper plate 600x600xmm thick i/c accessories and providing masonary enclosure with copper plate having locking arrangement and watering pipes etc.(but without charcoal and salt complete as reqd.)

Extra for using salt and charcoal for G.l.plates or copper plate earth electrode as reqd.

P/L earth connection from earth electrode with 4mm dia copper in 15 mm dia GI pipe as reqd.

S/F 48" sweep AC ceiling fan complete with down rod, canopy 3 (three) blades but without regulator etc as reqd. (make Bajaj/Usha or similar)

S/F 12"(305mm) dia light duty exhaust fan complete with all accessories i/c connection etc as reqd.

S/F Recess mounting LED down lighters BGSL 0101WH, 220223, cast aluminium housing, fixed with collimated lens, 1x1W white LED mounted on MCPCB, extruded Al. Heat sink spring loaded mounting clips comlplete with connection etc. As reqd.

Fire Fighting

Supply and installation of ABC type fire extinguisher 4 kg

Supply and installation of CO2 type fire extinguisher

SUB-HEAD ; STAFF QUARTER BLOCK -2

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sandy soil under floors including, watering,ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level: a).1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 50 mm thick with cement concrete.(a). 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Extra for providing and mixing water proofing materials in cement concrete work 1 kg per 50 kg of cement.

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate of 20 mm nominal size) i/c finishing the top surface of concrete smooth.

Providing and laying in position ready mix plain cement concrete or site batched design mix cement concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana/ordinary portland/portland slag cement, admixture in recommended proportion as per IS 9103 to accelerate/retard setting of concrete, to improve ductility and workability without impairing strength, including pumping of concrete to site of laying, curing, carriage of all leads, but excluding the cost of centering, shuttering, finishing and reinforcements as per direction of engineer in charge, for the following grades of concrete.All works upto plinth level

Concrete of M25 grade with minimum cement content of 330 kg/cum

Providing and laying in position ready mix plain cement concrete or site batched design mix cement concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana/ordinary portland/portland slag cement, admixture in recommended proportion as per IS 9103 to accelerate/retard setting of concrete, to improve ductility and workability without impairing strength, including pumping of concrete to site of laying, curing, carriage of all leads, but excluding the cost of centering, shuttering, finishing and reinforcements as per direction of engineer in charge, for the following grades of concrete. All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of 330 kg/cum

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.

.a) Thermo-Mechanically Treated bars.

Centering and shuttering including strutting, propping etc. and removal of form for:

a) Foundations, footings, bases of columns, etc. for mass concrete.

b) Lintels, beams, plinth beams, girders, bressumers and cantilevers.

c) Suspended floors, roofs, landings, balconies and access platform.

d) Columns, Pillars, Piers, Abutments, Posts and Struts.

e) Stairs, (excluding landings) except spiral-staircases.

Brick work with Ist class common burnt clay F.P.S. (non modular) bricks in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with Ist class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1 : 3 (1 cement : 3 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames,wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for separately :Local best quality Tolhao wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Local best quality Tolhao wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10 x 15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :75x65x4 mm (heavy type)

Providing and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass handles with screws etc. complete : 125 mm

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing in position collapsible steel shutters with vertical channels 20xl0x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia, steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and laying rectified Glazed Ceramic floor tiles 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS :15622 of approved make in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc. complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08% and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of stepts , over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.

Sizes of Tiles 600x600 mm (double charged)Branded

Marble stone flooring with 18mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with : a) Raj Nagar plain

Tile work in skirting, risers of steps and dado (upto 2 m height) over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with pigment of matching shade complete.Mable tiles (polished ) Raj Nagar.

Extra for prefinished nosing to treads of steps of marble stone.

12 mm cement plaster 1:4 (1 cement:4 fine sand).

15 mm cement plaster on rough side of single or half brick wall mix : 1:4( 1 cement : 4 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade

New work (two or more coats) over and including priming coat with cement primer:-

Finishing walls with water proofing cement paint of required shade : New work ( Two or more coats applied @3.84 kg/10 sqm)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer

Providing and applying white cement based putty of average thickness 1mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coat:-With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

SANITARY FITTINGS COMPLETE

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: a).White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: a).W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: a).White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : a).One urinal basin with 5 litre white P.V.C. automatic flushing cistern

BRASS AND CP BRASS FITTINGS

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :a).15 mm nominal bore

Providing and fixing brass stop cock of approved quality. a).15 mm diameter

Providing and fixing Water Storage Tanks with 400 mm diameter nominal base G.I. overflow tube 25 mm nominal G.I. inlet and 15 mm nominal G.I. outlet tube i/c hoisting a height of 10 m above ground level. a).2000 litres net capacity storage tanks

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing :a).Rectangular shape 453x357mm

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing C.P. brass toilet paper holder

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

SH:-PVC Pipes and Fitting

Providing and fixing PVC soil ,waste and vent pipes.External a).100mm dia

Providing and fixing PVC vent cowl.a).100mm dia

Providing and fixing MS holder bat clamps of approved design to 100 mm HCI pipe socket i/c cost of cutting holes and making good the walls etc. including cost of cutting holes and making good the walls etc.

Providing and fixing PVC soil ,waste and vent pipes.a).75mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.A).Flexible pipe--32 mm dia

Supply and installation of water pump Tulu(Texmo) 1HP of approved quality.

INTERNAL ELECTRIFICATION INSTALLATION;

Wiring for light/fan point/Exhaust fan point/ call bell point with 1.5 mm2 PVC insulated copper conductor single core cable inPVC casing & capping with modular type switch,modular plate size,G.I. box and earthing the point with 1.5 mm2 PVC insulated copper conductor single core cable etc. as reqd.

1. Group A

2. Group B

C. Group C

Wiring for light point/power plug with 2x4 mm2 PVC insulated copper conductor single core cable in PVC casing & capping along with 1 no. 4mm2 PVC insulated copper conductor single core cable for loop earthing etc. as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) PVC insulated conductor single core cable in PVC casing & capping etc.as reqd.

(a) 2X1.5mm2+1X1.5mm2 earth wire

(b) 2X2.5mm2+1X2 .5mm2 earth wire

(c) 2X4mm2+1X4mm2 earth wire

(d)2X6mm2+2X6mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing modular plate and switch box i/c connection but excluding modular plate etc as reqd.

(a) 5/6 amps switch

(b) 15/16 amps switch

(c) 3 pin 5/6 amps socket outlet

(d) 6 pin 15/16 amps socket outlet

S/F stepped type electronic fan regulator on the existing modular plate switch box i/c connection but e/c modular plate etc.

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/lsolator) (a) 16 way double door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

S/F (following rating) double pole 240V isolator in the existing MCB DB complete with connection,testing and commissioning as reqd. (a) 63 amp

Earthing with copper plate 600x600xmm thick i/c accessories and providing masonary enclosure with copper plate having locking arrangement and watering pipes etc.(but without charcoal and salt complete as reqd.)

Extra for using salt and charcoal for G.l.plates or copper plate earth electrode as reqd.

P/L earth connection from earth electrode with 4mm dia copper in 15 mm dia GI pipe as reqd.

S/F 48" sweep AC ceiling fan complete with down rod, canopy 3 (three) blades but without regulator etc as reqd. (make Bajaj/Usha or similar)

S/F 12"(305mm) dia light duty exhaust fan complete with all accessories i/c connection etc as reqd.

S/F Recess mounting LED down lighters BGSL 0101WH, 220223, cast aluminium housing, fixed with collimated lens, 1x1W white LED mounted on MCPCB, extruded Al. Heat sink spring loaded mounting clips comlplete with connection etc. As reqd.

Fire Fighting

Supply and installation of ABC type fire extinguisher 4 kg

Supply and installation of CO2 type fire extinguisher

SUB-HEAD ;-ADDITIONAL CLASS ROOM. & COMPUTER LAB.

Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sandy soil under floors including, watering,ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work upto plinth level: a).1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 50 mm thick with cement concrete.(a). 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Extra for providing and mixing water proofing materials in cement concrete work 1 kg per 50 kg of cement.

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate of 20 mm nominal size) i/c finishing the top surface of concrete smooth.

Providing and laying in position ready mix plain cement concrete or site batched design mix cement concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana/ordinary portland/portland slag cement, admixture in recommended proportion as per IS 9103 to accelerate/retard setting of concrete, to improve ductility and workability without impairing strength, including pumping of concrete to site of laying, curing, carriage of all leads, but excluding the cost of centering, shuttering, finishing and reinforcements as per direction of engineer in charge, for the following grades of concrete.All works upto plinth level

Concrete of M25 grade with minimum cement content of 330 kg/cum

Providing and laying in position ready mix plain cement concrete or site batched design mix cement concrete for reinforced cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, portland pozzolana/ordinary portland/portland slag cement, admixture in recommended proportion as per IS 9103 to accelerate/retard setting of concrete, to improve ductility and workability without impairing strength, including pumping of concrete to site of laying, curing, carriage of all leads, but excluding the cost of centering, shuttering, finishing and reinforcements as per direction of engineer in charge, for the following grades of concrete. All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of 330 kg/cum

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. a) Thermo-Mechanically Treated bars.

Centering and shuttering including strutting, propping etc. and removal of form for:

Foundations, footings, bases of columns, etc. for mass concrete.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Suspended floors, roofs, landings, balconies and access platform.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Stairs, (excluding landings) except spiral-staircases.

Brick work with Ist class common burnt clay F.P.S. (non modular) bricks in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with Ist class common burnt clay F.P.S. (non modular) bricks in superstructure above plinth level upto floor V level in Cement mortar 1 : 3 (1 cement : 3 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames,wrought framed and fixed in position with hold fast lugs or with dash fastener of required dia and length (hold fast lugs or dash fastener shall be paid for separately :Local best quality Tolhao wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Local best quality Tolhao wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10 x 15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Providing and fixing bright finished brass butt hinges with necessary screws etc. complete :75x65x4 mm (heavy type)

Providing and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete : 250x10 mm

Providing and fixing bright finished brass handles with screws etc. complete : 125 mm

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing in position collapsible steel shutters with vertical channels 20xl0x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia, steel pulleys complete with bolts, nuts, locking arran

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal,complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required withPrecoated galvanised iron profile sheets 0.50 mm thick

Providing and fixing precoated galvanised steel sheet roofing accessories , Zinc coating 120gsm as per IS: 277 in 240mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws or with polymer coated J or L hooks, bolts and nuts and or G.I. seam bolts and nuts, G.I. plain and bitumen washers complete : Ridges plain (500 - 600mm).Precoated galvanised iron profile sheets 0.50 mm thick

Steel work in built up tubular (round, square or rectangular tubes etc.) trusses etc., including cutting, hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted including special shaped washers etc. complete. Electric resistance or induction butt welded tubes.

FALSE CEILING

Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections, power pressed from M.S. sheet and galvanised with zinc coating of 120 gms/ sqm (both sided inclusive) as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5mm diax50mm long with 6mm dia bolts,other flange of cleat fixed to the angle hangers of 25x25x0.55mm of required length with nuts and bolts of required size and the other end of the angle hanger fixed with intermediate G.I. channels 45x15x0.9mm running at the spacing of 1200mm centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre, with 25mm long drive-all screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishng to

12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I,

Providing and fixing 20mm plank as eave board with :- Uningthou wood.

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Size of Tile 600 x 600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08% and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of stepts , over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.

Sizes of Tiles 600x600 mm (double charged)Branded

Marble stone flooring with 18mm thick marble stone (sample of marble shall be approved by Engineer-in-charge) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with : a) Raj Nagar plain

Tile work in skirting, risers of steps and dado (upto 2 m height) over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm including pointing in white cement mixed with pigment of matching shade complete.Mable tiles (polished ) Raj Nagar.

Extra for prefinished nosing to treads of steps of marble stone.

12 mm cement plaster 1:4 (1 cement:4 fine sand).

15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 ( 1 cement :43 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade

New work (two or more coats) over and including priming coat with cement primer:-

Finishing walls with water proofing cement paint of required shade : New work ( Two or more coats applied @3.84 kg/10 sqm)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer

Providing and applying white cement based putty of average thickness 1mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coat:-With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture

SANITARY FITTINGS COMPLETE

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: a).White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: a).W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: a).White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : a).One urinal basin with 5 litre white P.V.C. automatic flushing cistern

BRASS AND CP BRASS FITTINGS

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :a).15 mm nominal bore

Providing and fixing brass stop cock of approved quality. a).15 mm diameter

Providing and fixing Water Storage Tanks with 400 mm diameter nominal base G.I. overflow tube 25 mm nominal G.I. inlet and 15 mm nominal G.I. outlet tube i/c hoisting a height of 10 m above ground level. a).2000 litres net capacity storage tanks

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :a).Rectangular shape 453x357 mm

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing C.P. brass toilet paper holder

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

SH:-PVC Pipes and Fitting

Providing and fixing PVC soil ,waste and vent pipes.External a).100mm dia

Providing and fixing PVC vent cowl.a).100mm dia

Providing and fixing MS holder bat clamps of approved design to 100 mm HCI pipe socket i/c cost of cutting holes and making good the walls etc. including cost of cutting holes and making good the walls etc.

Providing and fixing PVC soil ,waste and vent pipes.a).75mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.A).Flexible pipe--32 mm dia

Supply and installation of water pump Tulu(Texmo) 1HP of approved quality.

SEPTIC TANK

Earthwork in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms lift upto 1.5metres including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 metres All kinds of soil.

Filling available excavated earth(excluding rock) in trenches,plinth sides of foundation etc. in layers not exceeding 20 cm in depth,consolidating each deposited layer by ramming and watering lead upto 50 metres lift upto 1.5 metre

P/L cement concrete in foundation and plinth excluding the cost of centering and shuttering in 1:4:8(1 cement: 4course sand: 8 graded stone aggregate 40mm. nominal size

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto Plinth level. Concrete of M-25 grade with minimum cement content of 330 kg/cum. All works upto Plinth level.

Concrete of M-25 grade with minimum cement content of 330 kg/cum.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto Plinth level. Concrete of M-25 grade with minimum cement content of 330 kg/cum. All works upto Plinth level.

Concrete of M-25 grade with minimum cement content of 330 kg/cum.

Steel reinforcement for R.C.C work including straightening,cutting, bending, placing in position and binding all complete.a)Thermo mechanically treated bars

Providing form works i/c centering and shuttering so as to give a rough finish, strutting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4 m and removal of the same for in-situ reinforced concrete and plain concrete work in

(a).Foundation, footing, bases of columns etc. and mass concrete.

b).Suspended floors, roofs, landings, balconies and access platform.

c).Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Providing and fixing C.I. Cover frame (for manhole and chambers).a).600 mm x 450 mm (heavy duty)

INTERNAL ELECTRICFICATION INSTALATION (IEI).

Wiring for light/fan point/Exhaust fan point/ call bell point with 1.5 mm2 PVC insulated copper conductor single core cable inPVC casing & capping with modular type switch,modular plate size,G.I. box and earthing the point with 1.5 mm2 PVC insulated copper conductor single core cable etc. as reqd.

1. Group A

2. Group B

C. Group C

Wiring for light point/power plug with 2x4 mm2 PVC insulated copper conductor single core cable in PVC casing & capping along with 1 no. 4mm2 PVC insulated copper conductor single core cable for loop earthing etc. as reqd.

Wiring for circuit/Sub-main wiring with earth wire with (the following sizes of) PVC insulated conductor single core cable in PVC casing & capping etc.as reqd.

(a) 2X1.5mm2+1X1.5mm2 earth wire

(b) 2X2.5mm2+1X2 .5mm2 earth wire

(c) 2X4mm2+1X4mm2 earth wire

(d)2X6mm2+2X6mm2 earth wire

Supply and fixing (following modular type switch/socket) on the existing modular plate and switch box i/c connection but excluding modular plate etc as reqd.

(a) 5/6 amps switch

(b) 15/16 amps switch

(c) 3 pin 5/6 amps socket outlet

(d) 6 pin 15/16 amps socket outlet

S/F stepped type electronic fan regulator on the existing modular plate switch box i/c connection but excluding modular plate etc.

S/F (following way) single/double pole and nuetral, sheet steel MCCB distributuion board, 240V on surface/recessed complete with tinned copper bus bar neutral bus bar, earth bar,din bar detachable gland plate, interconnection, phosphatized and powder painted i/c earthing etc as reqd (but without MCB/RCCB/lsolator) (a) 16 way double door

S/F 5 amp to 32 amp rating 230V 'B' series MCB for lighting and other load of (following poles) in the existing MCB DB complete with connection testing and commissioning etc.as reqd. (a) Single pole

S/F (following rating) double pole 240V isolator in the existing MCB DB complete with connection,testing and commissioning as reqd. (a) 63 amp

Earthing with copper plate 600x600xmm thick i/c accessories and providing masonary enclosure with copper plate having locking arrangement and watering pipes etc.(but without charcoal and salt complete as reqd.)

Extra for using salt and charcoal for G.l.plates or copper plate earth electrode as reqd.

P/L earth connection from earth electrode with 4mm dia copper in 15 mm dia GI pipe as reqd.

S/F 48" sweep AC ceiling fan complete with down rod, canopy 3 (three) blades but without regulator etc as reqd. (make Bajaj/Usha or similar)

S/F 12"(305mm) dia light duty exhaust fan complete with all accessories i/c connection etc as reqd.

S/F Recess mounting LED down lighters BGSL 0101WH, 220223, cast aluminium housing, fixed with collimated lens, 1x1W white LED mounted on MCPCB, extruded Al. Heat sink spring loaded mounting clips comlplete with connection etc. As reqd.

Fire Fighting

Supply and installation of ABC type fire extinguisher 4 kg

Supply and installation of CO2 type fire extinguisher

SUB-HEAD ;- LAND DEVELOPMENT :-

Banking excavated earth in layers not exceeding 20 cm. in depth, breaking clods,watering, rolling each layer with ½ tonne roller, or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up, in embankments for roads, flood banks, marginal banks, and guide banks etc., lead upto 50 m and lift upto 1.5 m. All kinds of soil

Turfing with good quality fresh "Tingthou" grass etc. 15 m C/C including watering for 30 days.

SUB-HEAD : RETAINING WALL.

Earthwork in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30cm in depth,1.5 m in width as well as 10 sqm on plan) including getting out and disposed of excavated earth, lead upto 50m and lift upto 1.5m, as directed by the Engineer-in-charge.(a) All kind of soil.

Providing and laying cement concrete of specified grade excluding the cost of centering and footing shuttering- All work upto plinth level:- 1:5:10 (1 cement : 5 C/Sand: 10 graded stone aggregate 40mm nominal size..

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works upto plinth level

Concrete of M-25 grade with minimum cement content of 330 kg/cum.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All works above Plinth level upto floor V Level.

Concrete of M-25 grade with minimum cement content of 330 kg/cum.

Centering and shuttering including strutting, propping etc. and removal of form for:- Wall ( any thickness ) including attached pilasters, buttresses, plinth and string courses etc.

a)Vertical surface such as walls (any thickness), partition and the like i/c attached pilasters, buttresses, plinth and the string courses and the like

Reinforcement for R.C.C work I/c bending, binding and placing in position complete ………. ( a) Tor steel.

15mm cement plaster 1:4 ( 1 cement : 4 coarse sand )

SUB-HEAD :-REINFORCEMENT CONCRETE PAVEMENT .

Construction of granular sub-base by providing close graded Material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place with rotavator at OMC, and compacting with vibratory power roller to acheive the desired densi

(i) Grading-II Material

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling eith 3 wheeled steel/ vibratory roller in stages to proper grade and chambe

A) By Manual Means Grading-II

a) Using Screeing Crushable type such as Moorum or Gravel

Construction of dry lean cement concrete sub-base over a prepared sub-grade with coarse and fine aggregate conforming to IS : 383, the size of coarse aggregate not exceeding 25mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10Mpa at 7days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller,finishing and curing.

Construction of reinforced-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with approve grade cement @340 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, replacing cement by fly ash to the extent of 15 % and sand by 10%, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing.

SUB-HEAD : Procurement of Science Lab Equipment for Physics, Chemistry and Biology.

(A) Physics

DeSaughty bridge- For comparison of capacities of condensers; made of metal film resistances of 1% accuracy

Anderson Bridge- For measurement of inductance in terms of capacity and resistance

Rayleigh's self inductance bridge- to measure the self inductance of a coil

Compund pendulum- brass C.P; complete with wall bracket

Kater's reversible pendulum-brass

Stand for Kater's reversible pendulum or copound pendulum

Young's modulus apparatus-brass frame, brass fitting

Case for young's modulus apparatus

Searle method for thermal conductivity- copper 37mm

Newton's law of cooling appartus- brass sheet

Spectrometers- deluxe model; complete in polished cabinate with lock and key scale 6" brass

Wooden box for sodium vapour lamp-55W

Sodium vapour lamp transformer-55W

Spectrometer prism; equilateral two faced polished 32x32 mm height, borosilicate crown glass prism

Spectrometer prism; equilateral two faced polished 32x32 mm height, dense flint glass prism

Advanced Travelling Microscopes with Square Pillar & special drum type verniers

Sodium vapour lamp transformer

Newton's Ring Microscope

Hollow Glass Prism 38x38x38mm

Vernier Caliper IME Type 8" L.C 0.01cm

Micrometer screw gauge stainless steel rod 25x1/2mm pitch

Leclanche cell charger porous pot with brass terminal

Diffraction grating-superior

Junction diode- PN junction diode on board with diagram engraved on the front panel

PN Junction diode/semi conductor diode chatacteristics apparatus- with four meters

Transistor on board NPN or PNP

Transistor chatacteristics apparatus- four round meters NPN/PNP combined

Zener diode on board

Zener diode chatacteristics apparatus- with four meters

Dual power supplies- 5 V or 6 V; 2 A

Dual power supplies- 12 V ; 2 A

Optical bench double rod standard patter 1 1/2 meter long having both s.s rods instead of steel rod

(B) Chemistry

1000005-Beaker 5ml, Borosil

1000006-Beaker 10ml, Borosil

1000D12-Beaker 50ml, Borosil

1000D21-Beaker 250ml, Borosil

1000D24-Beaker 500ml, Borosil

1000D29-Beaker 1000ml, Borosil

1509021-Bottle amber 250ml, Borosil

1625009-Relative density bottle 25ml, Borosil

1650021-Bottle amber 250ml, Borosil

2122012-Burette 50ml, Borosil

2123005-Burette 5ml, Borosil

2123006-Burette 10ml, Borosil

2981005-Cylinder graduated 5ml, Borosil

2981009-Cylinder graduated 25ml, Borosil

2981016-Cylinder graduated 100ml, Borosil

2981029-Cylinder graduated 1000ml, Borosil

3084042-Dessicator amber, Borosil

3160065-Petri dishes, Borosil

4385B21-Flask 250ml, Borosil

4385A24-Flask 500ml, Borosil

4385A16-Flask 100ml, Borosil

4989016-Flask amber 100ml, Borosil

5019012-Flask amber 50ml, Borosil

5640005-Flask volumetric 5ml, Borosil

6140057-Funnels, Borosil

7101001-Pipette 1ml, Borosil

7101002-Pipette 2ml, Borosil

7101006-Pipette 10ml, Borosil

7101008-Pipette 20ml, Borosil

9911005-Culture tube amber 5ml, Borosil

9910005-Culture tube 5ml, Borosil

030010-ACCUPIPETTE-Variable Volume Pipette 0.5-2ul, Tarsons

030020-ACCUPIPETTE-Variable Volume Pipette 2-20ul, Tarsons

030030-ACCUPIPETTE-Variable Volume Pipette 10-100ul, Tarsons

030040-ACCUPIPETTE-Variable Volume Pipette 20-200ul, Tarsons

030050-ACCUPIPETTE-Variable Volume Pipette 200-1000ul, Tarsons

1500024-Reagent bottle 500ml, Borosil

1250022-Bottle BOD 300ml, Borosil

2124012-Burette 50ml, Borosil

3021016-Cylinders 100ml, Borosil

4980016-Conical flask 100ml, Borosil

4980021-Conical flask 250ml, Borosil

5400024-Flask with stopper 250ml, Borosil

6140065-Funnels, Borosil

7062P09-Pipette 25ml, Borosil

9820U08-Test tube with rim, Borosil

LATG8888B10-Tongs for beaker and flask 10", Borosil

LATH88880000-Test tube holders, Borosil

LATS8888H25-Test tube stand, Borosil

166024-Bottle wash 500ml, Borosil

2124016-Burette 100ml, Borosil

5641024-Flask volumetric 500ml, Borosil

7200006-Weighning scoop 10ml, Borosil

LABR8888013-Burners, Borosil

LASP8888006-Spatula, Borosil

9986072-Watch glass 80ml, Borosil

9986079-Watch glass 120ml, Borosil

9100P02-Microscopic slide, Borosil

9115S01-Cover glass square 18x18mm, Borosil

93160077-Petridish 100x17mm, Borosil

3363042-Water distillation apparatus cap 2.5 litre/hr., with DAPS, Borosil

4060009-Flask 25ml, Borosil

4060012-Flask 50ml, Borosil

4060016-Flask 100ml, Borosil

5420028-Kjejdhal flask long neck, Borosil

2124006-Burette 10ml, Borosil

7057P10-Pipettes 10.75ml, Borosil

3083041-Dessicators 100ml, Borosil

6101068-Chromatography column, Borosil

Calcium Carbonate (Marble Chips) 500gm, Avantor/SRL/Himedia

Ammonium Chloride 500gm, Avantor/SRL/Himedia

Ammonium Carbonate 500gm, Avantor/SRL/Himedia

Barium Nitrate 500gm, Avantor/SRL/Himedia

Barium Chloride 500gm, Avantor/SRL/Himedia

Lead Nitrate 500gm, Avantor/SRL/Himedia

Copper Sulphate 500gm, Avantor/SRL/Himedia

Ferric Chloride 500gm, Avantor/SRL/Himedia

Zinc Sulphate 500gm, Avantor/SRL/Himedia

Ferrous Sulphate 500gm, Avantor/SRL/Himedia

Calcium Chloride 500gm, Avantor/SRL/Himedia

Magnesium Carbonate 500gm, Avantor/SRL/Himedia

Zinc Sulphate 500gm, Avantor/SRL/Himedia

Calcium Hydroxide 500gm, Avantor/SRL/Himedia

Ammonium Acetate 500gm, Avantor/SRL/Himedia

Ammonium Oxalate 500gm, Avantor/SRL/Himedia

Ammonium Sulphate 500gm, Avantor/SRL/Himedia

Ammonium Thiocyanate 500gm, Avantor/SRL/Himedia

Ammonium Molubdate 500gm, Avantor/SRL/Himedia

Cobalt Nitrate 100gm, Avantor/SRL/Himedia

Silver Nitrate 25gm, Avantor/SRL/Himedia

Dimethyle Glyoxime 500gm, Avantor/SRL/Himedia

Lead Acetate 500gm, Avantor/SRL/Himedia

Potassium Chromate 500gm, Avantor/SRL/Himedia

Potassium dichromate 500gm, Avantor/SRL/Himedia

Potassium Ferrocyanide 500gm, Avantor/SRL/Himedia

Potassium Thiocyanate 500gm, Avantor/SRL/Himedia

Phenolphthalein 125ml, Avantor/SRL/Himedia

Methyle Orange 125ml, Avantor/SRL/Himedia

Sodium Thiosulphate 500gm, Avantor/SRL/Himedia

Potassium permanganate 500gm, Avantor/SRL/Himedia

Potassium Iodide 500gm, Avantor/SRL/Himedia

(C) Biology

3160077-Petridishes 100x17mm, Borosil

3022016-Measuring cylinder 100ml, Borosil

3022021-Measuring cylinder 250ml, Borosil

3022024-Measuring cylinder 500ml, Borosil

4980021-Conical flask 250ml, Borosil

1000D12-Beaker 50ml, Borosil

1000D21-Beaker 250ml, Borosil

1000D24-Beaker 500ml, Borosil

1000D29-Beaker 1000ml, Borosil

9800U04-Test tube 15x125ml, Borosil

Capilary tube

Petroleum ether 60-800C 500ml, Avantor/SRL/Himedia

Acetone 500ml, Avantor/SRL/Himedia

Sodium hydroxide flask 500gm, Avantor/SRL/Himedia

Sefranine stain 125ml, Avantor/SRL/Himedia

Formaldehyde solution 2500ml, Merck

Filter paper grade 1, Whatman

Mortar and pestle 50mm

Chromatography paper

Prepared slide in mitosis

GE29-Monocular student compound microscope

Thermometer 110oC

Permanent slide of blastula

Permanent slide of T.S testis

Permanent slide of overy

Spirit lamp s.s

Sucrose 500gm, Avantor/SRL/Himedia

Potassium nitrate 500gm, Avantor/SRL/Himedia

Boric acid 500gm, Avantor/SRL/Himedia

Acetic acid 500gm, Avantor/SRL/Himedia

Hydrochloric acid 500ml, Avantor/SRL/Himedia

Simple microscope

Starch soluble 500gm, Avantor/SRL/Himedia

Stannous chloride 250gm, Avantor/SRL/Himedia

Zinc dust 250gm, Avantor/SRL/Himedia

Museum specimen: Spongilla

Museum specimen: Ascaris lunbricaida

Bunsen burner with stop cock

Sodium nitropruside 100gm, Avantor/SRL/Himedia

Sodium phosphate 500gm, Avantor/SRL/Himedia

Glycerine 500ml, Avantor/SRL/Himedia

Saffranine 125ml, Avantor/SRL/Himedia

Fehling solution A 500ml, Avantor/SRL/Himedia

Fehling solution B 500ml, Avantor/SRL/Himedia

Benedicts solution 500ml, Avantor/SRL/Himedia

Acetocarmine 125ml, Avantor/SRL/Himedia

Cover slip 18x18mm

2122012-Burette 50ml, Borosil

2123005-Burette 5ml, Borosil

2123006-Burette 10ml, Borosil

2981005-Cylinder graduated 5ml, Borosil

2981009-Cylinder graduated 25ml, Borosil

2981016-Cylinder graduated 100ml, Borosil

2981029-Cylinder graduated 1000ml, Borosil

7101001-Pipette 1ml, Borosil

7101002-Pipette 2ml, Borosil

7101006-Pipette 10ml, Borosil

7101008-Pipette 20ml, Borosil

030010-ACCUPIPETTE-Variable Volume Pipette 0.5-2ul, Tarsons

030020-ACCUPIPETTE-Variable Volume Pipette 2-20ul, Tarsons

030030-ACCUPIPETTE-Variable Volume Pipette 10-100ul, Tarsons

030040-ACCUPIPETTE-Variable Volume Pipette 20-200ul, Tarsons

030050-ACCUPIPETTE-Variable Volume Pipette 200-1000ul, Tarsons

LATG8888B10-Tongs for beaker and flask 10", Borosil

LATH88880000-Test tube holders, Borosil

LATS8888H25-Test tube stand, Borosil

6140065-Funnels, Borosil

166024-Bottle wash 500ml, Borosil

5640005-Flask volumetric 5ml, Borosil

1500024-Reagent bottle 500ml, Borosil

1250022-Bottle BOD 300ml, Borosil

SUB-HEAD : Procurement of 50 (Fifty) Computers

Intel Core i5 12th Gen 1240H Processor, Onboard or 2x SODIMM, 1x eMMC ( Small code only, option) 1x M.2 2280 SSD 1x 2.5 inch HDD, Intel UHD Graphics for 12 Gen Intel processor, 2x DDMI-Out, LAN : 1x 10/100/1000 Mbps adaptive Wi-Fi : Onboard or M.2 2230 Wi-Fi Module, Windows 10/Windows 11/Linux MONITOR MSI 22 INC MP223 100MHZ FULLHD

Andy Pamei (BID ID -10695)