SPECIAL REPAIR TO CERTAIN SMQS PHASE II AT AF STN SINGARSI UNDER AGE I AF SINGARSI

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L for coloured non skid ceramic tiles 6 to 7 mm thick (Square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:4) and cement slurry complete all as specofoed and as directed.

M&L Glazed ceramic coloured designer seamless tiles 450x300x7-8 mm thick on vertical surface as in skirting, dado set and jointed with neat cement slurry and pointed in white or coloured cement to match with the shade over and including 10mm thick screed in CM 1:3 complete all as specified and as directed.

M&L Vitrified tiles joint free light shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors etc.set and jointed in neat cement slurry and pointed with white or coloured cement to match with shade over and including screed bed 15mm thick in CM 1:4 and cement slurry complete all as specified and as directed.

M&L Vitrified tiles light shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, as on vertical surfaces etc.set and jointed in neat cement slurry and pointed with white or coloured cement to match with shade over and including 10mm thick screed in CM 1:3 complete all as specified and as directed.

M & L Granite 18 to 20 mm thick (of any type) work (table rubbed and polishedin steps, jambs, pillars, window-cills, cooking platforms including screed bed cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to matchwith shade of granite including rounding chamfering of edges complete all as specified and as directed.

Demolition of reinforced cement concrete in any position (reinforcement cut as required to facilitate demolition) and removing rubbish to a distance 50m at low lying area complete all as specified and as directed.

M&L reinforced cement concrete nominal mix 1:2:4 type B1, using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

M&L reinforced cement concrete nominal mix 1:2:4 type B1, using 20 mm graded stone aggregate as in beams, lintel etc.above 1.5m clear span complete all as specified and as directed.

M&L reinforced cement concrete nominal mix 1:2:4 type B1, using 20 mm graded stone aggregate as in foundation, including raft footing, foundation beam, plinth beams base of column etc.complete all as specified and as directed.

Formwork to sides of concrete foundations, footing ,bases of colums, plinth beams rough finished surfaces and similar work complete all as specified and as directed.

Formwork to side and soffits of floor or roof beams,lintels etc flat for fair finished surfaces complete all as specified and as directed.

Use and waste for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces complete all as specified and as directed.

M&L reinforced cement concrete nominal mix 1:2:4 type B1, using 20 mm graded stone aggregate as in column, pillars, piers, post & studs etc. complete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions etc rough finished surfaces complete all as specified and as directed..

S&F mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.9mm dia or securing with clip complete all as specified and as directed.

All as per Item No 16 above but 5mm dia and over upto and incl. 10mm dia in stirrups spacers and binders complete all as specified and as directed.

Supply and fix in repair PVC valveless, syphonic action type, flushing cistern, 10 ltr capacity, low level, white, with inlet, ball valve, float and handle including brackets connection to pipes including PVC connection and 32mm dia PVC long bend flush pipe complete all as specified and as directed.

S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests & P or S trap (excluding flushing cistern and flush pipe) complete all as specified and as directed.

S&F in repairs Vitreous china water closet pan ( pedestal pattern), white including fixing bolts etc including plastic water closet seat, black/white closed pattern with flat bottom and cover and mild steel chromium plated hinging device etc. complete all as specified and as directed.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, coupling, strainer, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm complete all as specified and as directed.

S&F in repairs Vitreous China Wash hand basin white flat back with pedestal , size 580 mm x 450 mm size, excluding taps, chain & plug & porcelain stopper but incl brackets, 40/32 mm dia chromium plate coupling 32 mm dia, approved pedestal & cutting for and pinning ends of brackets or erecting stand complete all as specified and as directed.

S&F in repair Fancy type pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repair fancy type 15mm bore, chromium plated bib taps cast copper alloy with crutch or butterfly handle screwed down for iron pipecomplete all as specified and as directed.

S&F in repair Brass Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union alongwith arm 125mm and flange complete all as specified and as directed.

S&F in repairs fancy type chromium plated 15 mm bore stop valve/angle cock cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repair fancy type 15mm bore dia of conceled stop valves cast copper alloy screwed down high presure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repairs tubular towel rail brass chromium plated, 20mm dia, 60cm long between flanges complete all as specified and as directed.

S&F in repairs PVC (SWR) floor trap 75 mm, plain with CP grating including joining and solvent cement complete

S&F in repair HDPE pipes of pressure rating 6kg/sqcm of 32mm bore for outlet pipe of WHB complete all as specified and as directed.

S&F in repairs CP soap dish complete all as directed.

S&F Sheet glass shelf/corner shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long as in repairs complete all as specified and as directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

Taking down rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., removal to Store (measured overall as fixed along the centre line over fittings and accessories).

S&F PVC (SWR) pipes single socketed 110mm bore dia in any lenth with rubber ring jointeds, laid in trenches or in floors.

S&F PVC (SWR) pipes single socketed 75mm bore dia in any lenth with rubber ring jointeds, laid in trenches or in floors.

S&F PVC (SWR) 110mm dia bend any raius all as specified and directed.

S&F PVC (SWR) 75mm dia bend any raius all as specified and directed.

S&F 50 mm dia low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm fixed complete to walls, ceiling or in floors etc including cutting, chasing, pinning and making floor good with existing one all as directed

Cutting chases,pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps cills, sunshades, shelves,lintels etc; and cutting chases for concealed water tubing and making good, cutting not exc.10cm girth.

Taking up or down steel tubing pipe with connections for cleaning for refixing or removing or storeyard complete of bore 15mm.

Taking up or down steel tubing with connections for cleaning for refixing or removing or storeyard complete of bore 20mm.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15mm.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs,unions etc.) of nominal bore 20mm.

Demolition of Brickwork of stone/boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles all as directed.

M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar1:6

All as per item no-47 except stone

Extra over stone walling for hammer (granite or trap stone) dressing to face of stone wall and dressing of faces, beds and joint with maximum depression on face from straight edge held against the dressed surfaces n. exc. 20mm all as specified.

M & L Raised pointing to random or polygonal rubble,With cement mortar (1:4) uncoursed or brought upto courses

Taking down cement plaster of any description on brick or stone walls, Chajjas etc., including raking out joints, hacking for key, scrubbing down with water etc.

Material & Labour for 15mm thick rendering in Cement Mortar 1:6 on stone masonry surfaces, finished even and smooth without using any extra cement complete all as specified and as directed.

Material & Labour for 15mm thick rendering in two layer each of (10+5mm) thick Cement Mortar 1:4 on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing with water proofing compound finished even and smooth without using any extra cement. (Note- Water proofing compound measured seperately)

Supply only approved integral water proofing compound.

Preparation of old plastered or unplastered surfaces of walls including cornices, pillasters by brooming down or steel wire smoke, root, moulds, moss and efforescent salts, and trading oil and greasy spot by using suitable chemical & removing nails, making good holes with chalk whiting, filling cracks and brooming to remove all dirt etc and applying one coat of Cement based paint on old prepared surfaces of walls

M&L for preparation of new surface and and applying two coats of cement base paint over a coat of white cement primer on walls

M&L for preparation of newely plastered wall surfaces and applying two coats of Oil bound distemper over a coat of alkali resistant primer over 3mm wall care putty

M & L for Complete removal of existing treatment of walls including cornices, pillasters by brooming down or steel wire smoke, root, moulds, moss and efforescent salts, and trading oil and greasy spot by using suitable chemical & removing nails, making good holes with , filling cracks with birla white putty and brooming to remove all dirt etc and applying two coats of distemper over one coat of alkali resistant primer over 3mm wall care putty

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to beprepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete. Conforming to ( Fe-290 (Gde E-165))

M&L preparation of new steel surfaces of any description, over 10cm in width or girth,not otherwise described and apply two coats of synthetic enamel paints over a coat of red oxide zinc chrome primer

M & L Preparation of old wood and wooden based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint etc

M & L Preparation of old steel surfaces of any description not otherwise described over 10cm in width or girth and applying one coat of synthetic enamel paint etc

M&L for Preparation of old plastered or unplastered surfaces of walls including Cornices, pillasters by brooming down or steel wire smoke, root, moulds, moss and efforescent salts, and trading oil and greasy spot by using suitable chemical & removing nails, making good holes , filling cracks with birla white putty and brooming to remove all dirt etc and applying one coat of white wash on old prepared surfaces of walls

M&L for Preparation of old plastered or unplastered surfaces of ceiling including cornices, pillasters by brooming down or steel wire smoke, root, moulds, moss and efforescent salts, and trading oil and greasy spot by using suitable chemical & removing nails, making good holes , filling cracks with birla white putty and brooming to remove all dirt etc and applying one coat of white wash on old prepared surfaces of ceiling

Demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing rubbish to a distance n.exc 50m at low lying area

M & L for 75mm thick cement concrete (1:3:6) type C-2 ( using 40mm graded agg.) as in subbase/below the tiles.

M & L for 50mm thick cement concrete (1:3:6) type C-1 ( using 20mm graded agg.) as in floor finishing/Plinth protection cement concrete all as specified and diredted.

M & L for 40mm thick cement concrete (1:2:4) type B-1 ( using 20mm graded agg.) as in floor finishing surface even and smooth with using extra cement

M&L liquior finish/glossy finish chequered cement concrete tiles 30cm x 30cm x 22-25 mm thick, set, jointed and pointed in neat cement slurry in floors using white cement and pigments including 20mm thick screed bed in CM 1:6etc (as in patches and as per site condition)

Dismantling of wall and ceiling boards( fibre pulp insulation etc) any thickness including cover fillets all as specifed and directed.

M&L for 7 to 9 mm thick pre-painted gupsum building board size 595 x 595 mm PVC laminated at back side of board insulations and acoustic purpose flat in ceiling fixed. Note : (The rate inclusive of scaffolding and necessary arrangements)

S&F in repair aluminium powder coated snap grid frame work for false ceiling all as specified . NOTE: (The rate inclusive of scaffolding and necessary arrangements).

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified . NOTE: (The rate inclusive of scaffolding and necessary arrangements).

Taking down chowkats or frames with shutters n.exc 1.50Sqm (without taking off shutters from the frames).

All as per serial item No. 75 above but exc 1.50 Sqm and n.exc 4 Sqm each.

Taking down shutters exc 1 Sqm but n.exc 2 Sqm each complete all as directed.

Dismantling old particle boards/plywood as in shelves boarding, any description, fixed in any position with nails complete all as specified and directed.

S&F of Pressed steel frames 105 x 60 mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock striking plate etc. complete.

S&F of Pressed steel frames 125 x 60 mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock striking plate etc. complete.

M& L for Plain Cement Concrete (1:3:6) Type C-1 using 20mm graded stone aggegate as in hold fast block, copping, filling in hollow door frame, bedblock, etc.

S&F 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as directed.

S & F solid PVC door frame of size 50 x 47mm made out of 5mm veneere style, laminated PVC sheet reinforced with MS square tube, in opening

S&F Solid PVC double Door frame of size 50mm x 95mm made out of 5mm prelam veneered PVC sheet reinforced with M.S. tube, suppling & fixing in opening as specified and directed by Engr-in-Charge

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm prelam PVC sheet on back face complete all as specified and directed.

S&F Factory made solid panel wire guage PVC door shutter 30 mm thick both side prelam PVC sheet (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling wii be wire guage. The wire guage shall be wrappedon an additional square 8 mm MS solid tube.This tube shall be welded to MS tube. The wire guage shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing

S/F, Solid PVC Wall Lining consisting of 5mm thick coloured PVC veneer finish sheet inclusive of solvent cement and preparing existing surface and fixing at site on as cupboard etc as specified and directed

S/F 18mm thick Solid PVC Sandwich Panel with 1mm Plain PVC Sheet on both sides suitably fixed in M.S. angle frame work as per specification & drawing fixed as in shelving of cupboard etc

S&F in repairs harrison rails, anodised aluminium alloy with fixing brackets, stops, rollers etc.

S&F factory made solid PVC moulded door designer shutter 30 mm thick comprising of 30 mm thick solid particle board core in centre core, with 2,4 or 6 raised panel design with 2 mm thick moulded prelam PVC sheet on both face all as specified and directed by Engr-in-Charge

S&F MS butt hinges 100mm size, medium weight cold rolled mild steel complete all as directed.

S&F 200 mm length aluminum, anodised, barrel tower bolts of extruded section complete all as directed.

S&F 150 mm length aluminum, anodised, barrel tower bolts of extruded section complete all as directed.

S&F 100mm size of aluminum handles, cast type anodised complete all as directed.

S&F 125 mm size of aluminum handles, cast type anodised complete all as directed.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as directed.

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as directed.

S&F Mild steel framed work as in grills, with ends of bars shouldered work conforming to Fe-410-0 as per existing grills at site complete all as directed.

S&F MS flat iron hold fasts fixed to chowkats confirming to Fe-310-O etc, complete all as specified and directed.

S&F for stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel wire staples.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n,exc 0.50 Sqm in each pane complete all as directed.

S&F in repair 18/19mm thick Prelaminated particle board, one side preelam, one side veneered exterior grade, prelaminated one side with decorative choice lamination and other side balanceing white lamination fixed for cupboard and shelving/shutter complete all as specified and directed.

M&L for external teak wood lipping 12mm thick fixed with nails to particle board complete all as specified.

M&L for 100 mm long aluminium anodised Hasp and staple, safety type, brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified.

M&L for 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified.

M&L as in repair steel window of area n exc 2 sqm making in servicible condition (opening and closing of shutter) including necessary welding work,gas cutter, greasing including necessary box type hinges and handle if required etc complete all specified and directed.

M&L as in repair steel window of area n exc 1 sqm making in servicible condition (opening and closing of shutter) including necessary welding work,gas cutter, greasing including necessary box type hinges and handle if required etc complete all specified and directed.

S&F repair tubular brass chromium plated decorative 20mm curtain rod fixing with brackets complete all as specified.

S&F repair fancy type powder coated decorative curtain rod bracket and holder for fixing curtain rod complete all as specified.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Taking down shutter of any description exc 1sqn but n. exc 2sqm each and refixing in same position including resecuring or easing and adjusting complete all as specified.

S&F in repair MS medium weight 100mm butt hinges complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with stainless steel wire staples complete all as directed.

S&F in repair 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n,exc 0.50 Sqm in each pane complete all as directed.

S/F of steel window with side hung shutter including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as specified.

All as per item No 115 but without glazing bars

M& L steel ventilator with top hung shutter including hinges steel peg stay , complete.

Taking down existing water proofing treatment including cement plaster and cleaning with wire brushes roughening the surface and hacking out dirt, where directed and disposal of rubbish n,exc 50mm distance from the starting point

M&L for Rendering 10 mm thick in Cement Mortar 1:4 on fair faces of brick work or concrete surfaces, with WPC @3% by weight of cement, finished even and smooth with using extra cement Note:- Supply only water proofing compound shall be measured and paid separately.

M&L for APP based polymeric membrane minimum weighing 3.5kg/sqm and 3mm thick reinforced with polyester non-woven fabric (weight not less than 160gms/sqm) laid on surface applied with bitumenous primer @ 0.25 litres per sqm, by torch application with overlaps 100 mm on the traverse direction and 75 mm on longitudinal direction on existing RCC roof surface and applying one coat of aluminium paint over the top surfaces of membrane @ 0.11 Litres/Sqm

M&L for Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3

M&L for Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight)

Dismantling of asbestos cement (corrugated, semi corrugated etc) sheets in roof covering including ridges.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, eaves etc fixed with self tapping screws as complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in ridge/flusing/eves board of width or girth not less than 600mm complete all as specified and as directed.

M&L for Mild Steel work as in flat iron for fix the steel framework for eaves board and wind tie complete all as specified and as directed .

Dismantling PVC/cement water tank exc 500 ltrs but n exc 1000 ltr capacity

S & F rotational moulded polyethylene water storage tank triple layered ( cylindrical vertical with closed top) hoisted and fixed in position of1000 liters capacity confiring to IS specification

ELECTRIFICATION Note : Prior to commencement of electrical works, the contractor needs to submit valid Electrical Liscence in the name of himself/themself or Aggrement with agency having valid Electrical Liscence alongwith Agency's Electrical Liscense to the Accepting Officer for his approval through GE/AGE(I). In absence of such documents, no work will be executed at site and to be treated as defaulter on the Contrctor's part . In addition, Supervisor for execution of electrical works employed by the Contractor shall posses Supervisory Certificate of competancy issued by concerned State Govt/Union Territory and the Worker/Tradesman for execution of Electrical Works must hold necessary permit issued by concerned State Govt/Union Territory.

Taking down carefully unserviceable copper / aluminium point wiring (light, fan, bell socket or power) including all fittings such as switches, socket, ceiling roses , regulators and fittings complete and making good the disturbed surfaces all as directed by Engineer-in-Charge.

M&L for point wiring for one light/fan/bell with single core PVC insulated and unsheathed stranded FRLS copper conductor cable 1100 volts grade size 1.5 Sqmm (nominal area) in and including PVC casing capping 25/20 mm width with one single core PVC insulated unsheathed 1.5 Sqmm (nominal area) stranded FRLS copper conductor as earth continuity wire and connected to earth dolly including PVC switch board on existing wall surface for one light/fan point /bell point controlled by one number one way switch & making good the disturbed surface to match with existing surface/wall complete all as specified and as directed.

All as per Item No 2 here-in-before but for one 5 pin socket outlet 5 Amps on independent board with 1.5 Sqmm complete all as specified and as directed.

All as per item No 2 here-in-before but for one 5 pin socket outlet 5 Amps on the same board with other switches complete all as specified and as directed.

All as per Item No 2 here-in-before but for one 5 pin socket outlet 15 Amps on independent board with 4 Sqmm copper cable FRLS & 2.5 Sqmm FRLS copper cable for earth continuity wire complete all as specified and as directed.

S&F for switch piano flush type 6 Amp single pole one way complete all as specified and as directed.

S&F for socket flush type 6 Amp 5 Pin complete complete all as specified and as directed.

S&F for switch socket combination 5 Pin 6 Amp universal complete all as specified and as directed.

S&F for switch socket combination 5 Pin, 6/15 Amp universal complete all as specified and as directed.

S & F ceiling rose, 3 phase/PVC/Polycarbonate, isolated body complete all as specified and as directed.

S & F call bell, ding dong AC 230 volts, single pole complete all as specified and as directed.

S & F bell push, flush type, 5 amp complete all as specified and ad directed.

S&F sheet metal enclosures for DB’s double door suitable for mounting of MCB’s/Isolators, 240 Volt, SPN, 12 way with built in bus bar complete after taking down old unserviceable DB's and including making good the distrubed surface and matching with existing colour complete all as specified and as directed. (Make:Havells ,Hager,Schineder or Legrands).

S&F VTPN distribution board with provision of MCCB as incommer, double door suitable for mounting MCB's/Isolators, 240 Volt,4 way with built in160A rated bus bar and with out MCCB complete after taking down old unserviceable DB's and including making good the distrubed surface and matching with existing colour complete all as specified and as directed. (Make: C&S (Cat Part No: CS DB MCCB100DD04IP43 or equivalent make in Hager/Siemens/Legrand

M&L for MCCB, 4P, 415V, overload adjustable 0.63 - 0.8-1 x in short circuit fixed 63 Amps breaking capacity 16KA complete all as specified and as directed. (Make:Hager ,Schnieder or Legrands)

M & L for MCB, SPN, 240 V, 40 to 63A Amps, and ‘C’ series breaking capacity 10 KA complete ISI marked , all as specified and as directed.

M & L for MCB, SP, 240V,40 Amps and ' B ' series breaking capacity 10 KA ISI marked complete, all as specified and as directed.

M & L for MCB, SP, 240V, 6 to 32 Amps and ' C ' series breaking capacity 10 KA ISI marked complete, all as specified and as directed.

Supply and fix ceiling fan regulator electronic Step type, solid state, 120W, 2 module, 240 volts, complete all as specified and as directed.

S&F metal clad box enclosure with socket plugtop and MCB SP 20 Amp flush of 240v mounting enclosure with 2 pin earth plug socket complete all as directed (Make - Havells Hager/legrand)

S&F in repair for wall mounted LED 4 feet 20 Watt fittings with high diffuser , driver holder extruded aluminium heat sink provided for energy efficient heat dissipation &integrated electronic incl all accessories and lamp ,internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed by Engr-in-charge. (Make :Crompton (LDL-20-CDL) , Bajaj/Philips/Havells)

S&F in repair for wall mounted LED 2 feet 10 Watt fittings with high diffuser , driver holder extruded aluminium heat sink provided for energy efficient heat dissipation &integrated electronic incl all accessories and lamp ,internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed by Engr-in-charge. (Make :Crompton (LDL-10-CDL) , Bajaj/Philips/Havells)

S&F in repair for LED light fitting, round surface mountable, 15W Wattt fittings with high diffuser , driver holder ,internally prewired complete all as specified and as directed by Engr-in-charge. (Make : Crompton (LCRP-15-CDL) , Bajaj/Philips/Havells)

Supply and fixing sub main wiring with two run of single core 2.5 Sqmm PVC insulated unsheathed stranded cable (FRLS) copper conductor drawn through PVC casing caping with all fittings including 2.5 sq mm PVC insulated unsheathed single core copper conductor as earth wire and including PVC casing caping after taking out old un serviceablewring complete and including PVC casing caping all as specified and as directed. Note : (i) Two run of single core cable 2.5 sq mm and one run earth wire 2.5 sq mm will be measured as one length.(Make: RR,KEI and Finolex for copper Cable and Prestoplast/Plaza for casing/conduit)

Supply and fixing sub main wiring with two run of single core 4 Sqmm PVC insulated unsheathed stranded cable (FRLS) copper conductor drawn through PVC casing caping with all fittings including 4.0 sq mm PVC insulated unsheathed single core copper conductor as earth wire and including PVC casing caping after taking out old un serviceablewring complete and including PVC casing caping all as specified and as directed. Note : (i) Two run of single core cable 4 sq mm and one run earth wire 4.0 sq mm will be measured as one length.(Make: RR,KEI and Finolex for copper Cable and Prestoplast/Plaza for casing/conduit)

Supply and fixing sub main wiring with two run of single core 6 Sqmm PVC insulated unsheathed stranded cable (FRLS) copper conductor drawn through PVC casing caping with all fittings including 6.0 sq mm PVC insulated unsheathed single core copper conductor as earth wire and including PVC casing caping after taking out old un serviceablewring complete and including PVC casing caping all as specified and as directed. Note : (i) Two run of single core cable 6.0 sq mm and one run earth wire 6.0 sq mm will be measured as one length.(Make: RR,KEI and Finolex for copper Cable and Prestoplast/Plaza for casing/conduit)

M&L for earthing complete with galvanised steel earth plate electrode 600x600x 6mm thick burried in ground (earth pit not less than 2.25 m deep below ground level0with top edge of the plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4.00mm dia by means of bolts, nuts, check nuts, and washers of GI or steel, GI strip protected by 40 mm bore medium grade GI pipe and other end connected to earth test point as directed including funnel with watering pipe 20 mm bore light grade GI, wire mesh charcoal or coke common salt laid in altrnative layer of 15 cm (complete thickness) all round the earth electrode, concrete earth pit in PCC(1:3:6) type C-1, 50 mm thick pre-cast RCC(1:2:4) type B-1 normally mix cover slab reinforced with in 8 mm dia TMT bar 10 cm C/C both ways and single handle of 10 mm dia round bar including necessary excavation, earth work etc. in soft/loose/hard soil and disposal of soil to a distance n.exc 50 m and necessry testing on completion all as shown in electrical plate No 3 MES schedule part-I complete all as specified and as directed.

Taking down ceiling fan/exhaust fan of any sweep and capacity by unscrewing nut/bolts from its position and fixing the same to its original place after necessary cleaning, oiling, greasing, replacement of bush, bearing and marking MES number all as directed by Engr-in-charge. (Note : Bush, bearing , measured and paid separately as supply only rates and fixing charges for spare parts shall deemed to be included in this item.

Supply and fixing rubber bush for shackle with bolt, nut and lock pin suitable for ceiling fan 1200/1400 mm sweep.

Supply and fixing bearing number of 6201/6202/6203/6204 as required, Make : SKF/NBC or Eequivalent

Supply and fixing condenser 2/2.5 Mfd

Supply and fixing PVC holder for condenser housing.

Supply and fixing only gun metal bush .

Supply and fix exhaust fan motor AC single Phase. 230V for size 300 mm , 85 watts sweep exhaust all as specified and directed

Supply & fixing blade made of iron suitable for Exhaust fan 300 mm sweep

Taking down / dismantling of defective / rusted storage type hot water gyser of 50/25 ltr capacity from different locations by disconnecting inlet / outlet connections and taking out unserviceable parts by unscrewing bolts and nuts etc deiscaling / cleaning inner servicing and etc. Checking defects, re-assembling and re-installing the gyser in position, connection and testing complete.

Supply & fix indication lamp (green / red) as required.

Supply& fix thermostat of range 0-90 degree centigrade as required.

Supply& fix heating element 2 KW (ISI Marked) cup type / thread type with the provision of thermal cut out as required.

Demolition of cement concrete (unreinforced) in roof floors other than ground floors beams staircases, landing, chhajjas and similar suspended work complete all as specified and directed.

M&L for PCC type B0 1:2:4 (12.5mm graded stone aggregate) as in roof padding chajjas repair complete all as specified and directed.

P .BANERJEE AND CO

SARASWATI ENTERPRISE INDEX NO. CEEC D-81

M/s PATEL ENGINEERING

MS AP CONSTRUTION AND CO

MS R.K.ENTERPRISE