CA NO CWE/PAT/T-08/2020-21 SPECIAL REPAIR TO SINGLE JCOS ACCN BLDG NO T-47 AND BLDG NO SM-7A (OR COOK HOUSE) UNDER GE NORTH PATIALA

Amount

Schedule 'A'Section-I (Building Works)

Total amount of Sch 'A' Sec I (Building Works)

Schedule 'A'Section-II (INTERNAL ELECTRIFICATION WORKS)

Total amount of Sch 'A' Sec II (Internal Electrification Works)

Schedule 'A'Section-III (Misc Items of Works) Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 siginifies this fact only.

Supply only integral liquid water proofing compound all as specified & as directed by Engineer-in-Charge.

Complete removal of existing treatment of any type/description from walls/RCC surfaces/ceiling/chajjas/roof projection etc with mechanical means/grinder complete all as specified and directed.

Applying 02 coats of interior emulsion paint (light shade) @ 10 sq.m/litre/2 coats by using roller to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed. Make of Interior Wall Primer : Asian / Berger / Nerolac [Best Quality]. Make of Interior Emulsion : Asian (TRACTOR) / Berger (BISON) / Nerolac (BEAUTY SMOOTH)

Applying 02 coats of interior emulsion paint (white shade) @ 10 sq.m/litre/2 coats to ceiling surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed. Make of Exterior Wall Primer : Asian / Berger / Nerolac [Best Quality]. Make of Exterior Emulsion : Asian (ACE) / Berger (WALMASTA) / Nerolac (SURAKSHA SUPERIOR)

Applying 02 coats of exterior emulsion paint (light shade) @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed.

S&F factory made ISI marked flush door shutters 35mm thick, BWP conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters incl two coat of synthetic enamel painting over a coat of pink primer complete all as specified and incl supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated all as specified including stainless steel 304 Grade wire cloth (0.36mm nominal dia of wire and average width of aperture 1.40mm) incl two coat of synthetic enamel painting over a coat of pink primer complete all as specified and including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x300mm - 1 No per leaf

Providing and fixing factory made extruded aluminium casement windows with 50 micron powder coating with provision for desert cooler, doubled panelled and double shutters consisting of frame and mullion of 101.60 X 44.45 X 1.29 mm and shutters made of 63.5 X 31.75 X 1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete fixed in all respect as specified including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 2 Nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 Nos per leaf. (c) Powder Coated Aluminium Handles 150 mm - 1 Nos per leaf. Make (Aluminium Sections) : Jindal/Valco/Galco/Hindalco or equivalent as approved by AO Note : Aluminium grills to be measured and paid separetly

Providing and fixing aluminium sliding windows with 50 micron powder coating, three track sliding windows with two glazed shutters, 5mm th tinted glass ordinary quality and one shutter of stainless steel wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm including good quality of bearing handle, locks, including EPDM gasket to render the glazing, air and water tight etc complete all as specified and as directed. catalouge numbers of Jindal company or equivalent make as specified. Sections of Jindal company : Three track bottom - 20957, Three track top/vertical-20958, handle-20606, Interlocking-20605, Top and Bottom - 20604. Make (Aluminium Sections) : Jindal or equivalent as approved by AO

S&F factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and complete fixed in all respect as specified. Make (Aluminium Sections) : Jindal/Valco/Galco/Hindalco or equivalent as approved by AO

S&F factory made aluminium 50 micron powder coated grill, opening size 101.6 X 63.5 mm (4"X2½") and of approx weight @ 1.345 Kg/sq.m complete fixed in position in windows in all respect as specified

M&L for single charge, stainfree, vitrified tiles, Premium (1st) quality straight edge, coloured tiles 600 X 600 mm and 9-10 mm thick, as in floors etc. in any pattern of light coloured tiles as in approved shade, set & jointed in neat cement including and over 20mm th screed bed in CM (1:4) and pointed in white coloured cement to match, in floors etc. complete all as specified. Make : Johnson/Kajaria/Somany/NITCO as approved by AO

Providing and Laying Premium (1st) quality digitally printed straight edge, punched, glazed ceramic rectangle tile in approved shade and finish in coloured tiles 600 X 300 mm and 8-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified. Note : Dado should be flushed with the wall plastering. Make : Johnson (Digital HD Tiles) (Barstow DK/LT/HL for Toilets & Verona LT/HL for Kitchens) or equivalent from Kajaria/Somany as approved by AO

M&L for anti-skid premium (1st) quality coloured tiles 400 X 400 mm and 7-8 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, as in skirting not 150mm high etc. in any pattern of light or dark tiles as approved to match the floor tiles, over & including 10 mm thick screed in cement mortar (1:4) complete all as specified.

M&L for anti-skid premium (1st) quality coloured tiles 400 X 400 mm and 7-8 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4) over and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for Baroda Green marble, machine cut as in shelves/steps/cills/jambs/skirting/border only in tile flooring and the like works and flooring etc, 15-16 mm thick including bull-nose the front length, set and jointed in cement slurry over & including screed of 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type granite polishing complete all as specified. Note : Single piece should be used in steps/cills/jambs/shelves.

S&F false ceiling of 12.5mm thick gypsum board over and including concealed grid system complete fixed in all respect and all as per manufacturer's instructions in one/two/three levels and making recess for light fittings as per pattern/design approved by Accepting Officer and including supply and fixing of items all as specified as below :-

(B) Suspended Plain Ceiling includes Perimeter Channel {Material-GI(IS513),YS-260Mpa,Finish- Galvanised 150GSM(IS27 )} is fixed along the perimeter of existing wall/ partition with the help of HILTI HPS - 1 (6x40) impact anchor, at 600mm centres. Make : ANCHOR / GYPBOARD / GYPROC. (C) Ceiling Angle {Material-GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277)} is suspended by fixing it to the Gyproc® soffit cleat {GI(IS513)YS-260Mpa,Finish-Galvanised 150GSM(IS277) }. Soffit Cleat and Gyproc® Rawl Plug- Ø8x45mm {Material-IS 513 CR2 grade, Zinc coating (7 to 8 microns) pull out load- 6.8kN for M30 concrete grade} creating 1220mm x 1220mm grid. Make : ANCHOR / GYPBOARD / GYPROC (D) Intermediate channel {Material-GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277) } is fixed to the Ceiling Angle with M6 x 12mm Hex Bolt & Hex Nut arrangement {Material–As per EN 10083 Finish – Zinc Plating} or with 2 Nos of Ø4.2x13 Gyproc® metal to metal screw {Material-Carbon steel EN-ISO 7049/50 Finish- Zinc Coating Thickness- 4.14micron.} Make : ANCHOR / GYPBOARD / GYPROC

(e) Ceiling Section {Material-GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277)} is then fixed to the Intermediate Channel {Material-GI(IS513),YS-260Mpa,Finish-Galvanised 150GSM(IS277)} with the help of Gyproc® Connecting Clip {Material-High carbon spring steel wire(BS970Gr.En42)-46-48HRC,Finish- Zinc plating 4-6 micron} and in direction perpendicular to the Intermediate channel at 457mm c/c. Make : ANCHOR / GYPBOARD / GYPROC (f) Single layer of 12.5mm tapered edge Plain (conforming to IS 2095-Part 1:2011, ISI Certified board) is then screw fixed to ceiling section with 25mm drywall screws {Material-Carbon steel EN-ISO 7049/50,Finish-Case hardened Grey Phosphating} at 230mm centres on ceiling section & 150mm at periphery of ceiling. Make : ANCHOR / GYPBOARD / GYPROC (g) Finally square and tapered edges of the boards are to be jointed and finished so as to have a flush look which includes filling and finishing with Pro-Fill Jointing compound (Conforms to ASTM C475), Gyproc® Joint Paper tape incl necessary putty and painting complete. Make : ANCHOR / GYPBOARD / GYPROC Note : The complete item shall be got executed through the authorised applicator of manufacturer only all as specified and directed. Make : ANCHOR / GYPBOARD / GYPROC

S&F stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets/finials fency type, stops fixed with ss screws etc all as specified & directed as in repair . Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

S&F vitreous china premium/1st quality wash basin half pedestal, white/ivory/off white, flat back, size 500 x 400 mm including pedestal, screws & plug and brackets etc. all accessories as recommended by manufacturer incl. CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling and completein all respect as per manufacturer's instructions and taking down existing of any description/size all as specified. Make : Hindware (WHB-Cleo (Cat No.- 10012), Waste Coupling-Cat No.- F850023 (Economy Model), Bottle Trap-Cat No.- F850072 (Economy Model) or equivalent from Parryware/Cera as approved by AO

S&F 6mm thick looking mirror fixed to wall with stainless steel plugs/connecter/spacers/screws etc. chrome finish with smooth finish edges/sides complete fixed in position all as specified and directed.

S&F soap dish, stainless steel of suitable size to accommodate soap , tooth brush glass and tooth paste complete all as directed and specified.

S&F overhead shower 70mm dia with 225-230mm long shower arm and incl all necessary accessories as recommended by manufacturer for fixing and taking down existing of any description/size complete in all respect all as specified.

S&F Bib taps, CP, fency type long nose with wall flange screwed for 15mm bore of iron pipe or for brass ferrule and fixed in position complete in all respect all as specified. Make : Jaquar (Continental Series)/ Hindware (Contessa Plus Series)/ Cera (Ocean Series)/ Prayag (Neptune Series)

S&F Pillar taps, fency type, long neck, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for 15mm bore of iron pipe and fixed in repairs all as specified. Make : Jaquar (CON-CHR-021KN) /Marc/Prima

S&F towel rod CP 60 cm long between flanges and including all accessories like brackets/screws etc as recommended by manufacturer and fixed in position complete all as specified. Make : Jaquar/Cera/Hindware/Marc/Prima

PVC(HDPE) SWR , 50 mm bore, single socketed in any length with rubber ring joints using solvent cement as per maunfacture instruction, laid in walls for connecting bottle traps complete all as specified. Make : Astral / Prince / Finolex

S&F stainless steel grating 150 x 150 mm size square shaped with cockroach trap for floor trap fixed in position complete all as specified .

S&F Angular Stop Cock, CP, fency type with wall flange, fency type chromium plated cast copper alloy screwed down, high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete in all respect all as specified.

M&L for dummy joints/construction joints 8mmx10mm as in PCC floors filled with polyurethane elastic adhesive/sealant (white/grey colour) of approx density 1.30kg/litre complete all as specified. Make : Sika flex

Disconnecting existing tanks, setting aside (or lowering if required) for repairing, cleaning, etc. and hoisting if required reconnecting and S&F tank cover and 20mm dia brass float valve, changing of chuk nuts, socket and re-fixing in position after cleaning the tank complete all as specified and directed.

Scrapping surfaces of roof by wire brushing removing all loose dirt and cleaning and washing down the surfaces with water complete all as directed.

S&F PTMT Jet Spray with 1.5 metre long flexible tube including making connections and fixed in position complete in all respect as specified. Make : Prayag (Cat No 522) or equivalent as approved by AO

S&F Pre-painted factory made galvalume aluminum zinc coating GI based plain sheet 0.45mm thick TCT of colour as approved as in gutters with 195mm high vertical sides and 220mm wide bottom having tensile strength of 550 Mpa for roof covering, including supply and fixing with all accessories all as recommended by manufacturers like fasteners/screws/brackets etc complete all as specified. Make : Tata Durashine or equivalent as approved

Providing and laying 3mm thick APP (Atactic Polyproplene Polymer) modified prefabricated five layer, weight not less than 4.0 Kg/Sqm water proofing membrane black finished, reinforced with non-woven polyster matt make as approved including of a coat of bitumen primer @ 0.40 ltr/sq.m by the same membrane manufacturer of density 0.87 to 0.89 Kg/Ltr at 25 degree C temperature and viscosity 70 - 160 cps Over the coat, 3mm th 5 layered APP membrane shall be laid using butane torch and sealling all joints etc after the surface complete as per standard practice as per manufacturers instructions. The vital physical and chemical parameters of the membrane shall be as under - (i) Joint strength in longitudinal and transverse direction at 23 degree C as 650/450N/5cms (ii) Tear strength in longitudinal and transverse direction as 300 / 250 N/. Softening point of membrane not less than 150 degree C Cold flexibility upto 20 degree C when tested in accordance with ASTM (D05147) (iii) The laying of membrane shall be got done through the authorised applicator of manufacturer of membrane only all as specified.

Supply and fixing modular white cover plate with frame for fixing of modular switch 12 module complete all as specified.

S&F tube light fitting LED type retrofit T-8, 20 watt, 4 ft long including LED tube rod and including 3 core flexible wire 0.5 sqmm copper cable all as specified & dierected .

S&F bulk head fitting LED type including 1 x9/10 watt LED lamp, with flexible wire 0.5 sqmm copper cable all as specified and directed. Note :-Bulk head fitting will be issue from store yard of MEs

S&F Modular metal box 12 module and complete all as specified & directed by Engr-in-Charge.

S&F LED security light fitting 30-35 watt complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable of size complete all as specified and directed. Make : Havells/phillips/C&S

Supply & Fix LED bulb 7 watt complete in all respect all as specified.

Supply & lay and testing cable XLPE insulated, screened PVC bedded galvanised steel strip or wire armoured heavy duty electric cable with aluminium conductor, 1100 volt grade of crosssectional area 16 Sqmm 2 Core all as specified & directed by Engr-in-Charge.

Hanging only ceiling fan after necessary piont wiring complete all as specified and directed.

AR CONSTRUCTIONS

M/S Mukesh Kumar Gupta

Buttar Construction Co.