Repair/Maint of street light, perimeter light, unit street light and other allied works at AF Stn Jaisalmer

Amount

Taking down of existing unserviceable Street Light of any type/Bollard Light/Perimeter Light /High mast Light and Building Security Light any type any make from pole, hangers, buildings/High mast Poles at any height etc any type complete after removing from existing bracket etc and re-fixing the same after necessary repair/ replacement of unserviceable Light with new fittings/component etc complete all as specified and directed. Note:- (i) Replacement and fixing of unserviceable component etc required will be measured & paid separately under respective items of this schedule. (ii) Fitting shall be connected with existing electric wire / cable, in case of existing wire / cable found unserviceable same shall be measured and paid in relevent items. (iii) Any type of Ladder for dismantling of light from pole/hanger/high mast pole shall be arranged by the contractor.

Supply only electronic driver suitable for LED street lights of capacity 45 watt to 90 watts, complete all as specified and directed.

Supply only electronic driver suitable for LED street lights of capacity 100 watt to 200 watts, complete all as specified and directed.

Supply only electronic driver suitable for LED street lights of capacity 250 watts, complete all as specified and directed.

Supply only surge protection device 10 KV, suitable for LED street lights of capacity 45 watt to 250 watts, single phase, 230 volt, 50 Hz, AC supply complete all as specified and directed.

Supply only LED lamp of capacity 50 watt, B-22 base, 230 volt, 50 Hz, complete all as specified and directed.

Supply only Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fitting complete all as specified and directed.

PVC elastomer insulated and fire retardant PVC sheathed, round or flat cable size 1.5 sqmm, 3 core multicore, industrial flexible cable with bright annealed, copper conductor, 1100 volts grade confirming to IS-694-1990 including taking down old unserviceable cable complete all as specified and directed.

Cable Junction box made out of polycarbonate with IP 55/IP 65 protection of size 200mm x 160mm x 98mm, 5 way having terminals for termination of cable with necessary nuts and bolts including 02 Nos polycarbonate cable gland, 01 Nos DIN rail for mounting of MCB and including MCB, 6 Amps, Single Pole, rupturing capacity 10 kA, and including fixing clamp of FI 25x3mm with necessary nuts and bolts including taking down old unserviceable complete all as specified.

Supply, laying, jointing and testing 1100 volts grade heavy duty cable PVC insulated aluminium solid conductor cable 10 sqmm, twin core, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 meter apart including 4mm suspension wire including taking down old unserviceable cable complete all as specified and directed.

Polypropylene random copolymer concealed (PPR) Pipes, 3 Layer, UV stabilised having thermal stability upto 93 degree centrigrade complete and fixed with the pole by providing Flat Iron clamps, nuts and bolts of size 25x25x3mm with nuts & bolts for protection of connecting wires, connection from Junction box to light fittings complete for outer dia 20mm (PN-16), including taking up or down old unserviceable pipe complete all as specified and directed.

Energy efficient LED street light fittings of capacity not less than 36 watt, pressure die cast alluminium housing & toughened glass with IP-66 degree of protection, individuals LED's should have lenses for better throw across & along road range 140-280 volts fittings should be provided 10 KV surge protection external and apart from this surge, arrestor driver should have additional 4 KV surge protector in built in driver for maximised protections, should have lumens output of 100 lumens watt minium protections facility in drivers, driver should be potted type for viberation proof performance & includings making electrical connections fixed as in repair complete all as specified and directed. Note :- Driver should be BIS registered with "R" marking.

Energy efficient LED street light fittings of capacity not less than 45 watt, pressure die cast alluminium housing & toughened glass with IP-66 degree of protection, individuals LED's should have lenses for better throw across & along road range 140-280 volts fittings should be provided 10 KV surge protection external and apart from this surge, arrestor driver should have additional 4 KV surge protector in built in driver for maximised protections, should have lumens output of 100 lumens watt minium protections facility in drivers, driver should be potted type for viberation proof performance & includings making electrical connections fixed as in repair complete all as specified and directed. Note :- Driver should be BIS registered with "R" marking.

Energy efficient LED street light fittings of capacity not less than 60 watt, pressure die cast alluminium housing & toughened glass with IP-66 degree of protection, individuals LED's should have lenses for better throw across & along road range 140-280 volts fittings should be provided 10 KV surge protection external and apart from this surge, arrestor driver should have additional 4 KV surge protector in built in driver for maximised protections, should have lumens output of 100 lumens watt minium protections facility in drivers, driver should be potted type for viberation proof performance & includings making electrical connections fixed as in repair complete all as specified and directed. Note :- Driver should be BIS registered with "R" marking.

Energy efficient LED street light fittings of capacity not less than 70 watt, pressure die cast alluminium housing & toughened glass with IP-66 degree of protection, individuals LED's should have lenses for better throw across & along road range 140-280 volts fittings should be provided 10 KV surge protection external and apart from this surge, arrestor driver should have additional 4 KV surge protector in built in driver for maximised protections, should have lumens output of 100 lumens watt minium protections facility in drivers, driver should be potted type for viberation proof performance & includings making electrical connections fixed as in repair complete all as specified and directed. Note :- Driver should be BIS registered with "R" marking.

LED flood light of capacity 150 watt, aesthtically design, having epoxy powder coated pressure die cast aluminium housing with IP 66 protection high output emitter LED for better thermal management of capacity 150 watt (5700 K CCT), system luminous efficacy Im/w grater than or equal to 100 Im/w, high efficiency long life LED module with SMD LED package mounted on MCCB, viewing angle 120 degree, high quality toughened glass cover, IK 07 powered by 02 Nos, integral, isolated electronic LED drivers (SMPS based constant current supply) with lower THD output open/short circuit protection, over voltage protection, surge voltage, protection with SPD not less than 10 KV and other safety test as per IS-1985 part-2/sec 13, the LED flood light should be LM-79 report and IES file including taking down old unserviceable LED light fittings complete all as specified and directed.

LED flood light of capacity 200 watt, aesthtically design, having epoxy powder coated pressure die cast aluminium housing with IP 66 protection high output emitter LED for better thermal management of capacity 200 watt (5700 K CCT), system luminous efficacy Im/w grater than or equal to 100 Im/w, high efficiency long life LED module with SMD LED package mounted on MCCB, viewing angle 120 degree, high quality toughened glass cover, IK 07 powered by 02 Nos, integral, isolated electronic LED drivers (SMPS based constant current supply) with lower THD output open/short circuit protection, over voltage protection, surge voltage, protection with SPD not less than 10 KV and other safety test as per IS-1985 part-2/sec 13, the LED flood light should be LM-79 report and IES file including taking down old unserviceable LED light fittings complete all as specified and directed.

Energy efficient LED Post Top light fittings made in spun aluminium powder coated housing with higher efficiency lighting & IP-66 protection of capacity not less than 20 watt, range 140-280 volts fittings should be provided 10 KV surge protection external and apart from this surge, arrestor driver should have additional 4 KV surge protector in built in driver for maximised protections, driver should be potted type for viberation proof performance & includings making electrical connections, mounting arrangements, suitable size GI pipe light grade fittings, PCC etc fixed as in repair complete all as specified and directed.

LED bollard light (Flute decorative type in cylinderical shape with opel acylic diffuser and IP 66 protection with reflector 8-9 watt having fixing arrangements at bottom with necessary nuts, bolts, washers complete, including taking down old unserviceable LED bollard fittings complete all as specified and directed.

LED bollard light inverted Pyramid Tripod type with reflactor 10 watt with soft 360 degree light distribution having fixing arrangement at bottom with neccesary nuts, bolts, washers complete including taking down old unserviceable LED bollard fittings complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc. or for laying of cables, pipes, erection of poles, structs/stays etc. or for shafts, wells, cesspits, manholes, pier holes, etc not exceeding 10 sqm on plan and getting out any type of soil complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in soft/loose soil complete all as specified.

Removal of excavated soil/ material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.50 metre above the starting point complete all as specified.

Stone patti 40 to 50mm thick rough dressed Jodhpur stone slab cover in trenches for protection of cable 25 to 35cm wide and not less than 80cm in length laid dry abutting each other with gap between adjacent slab not exceeding 10mm over sand cushioning complete all as specified and directed.

Dry tibba sand cushioning to underground cable provided with a layer of 8cm deep before laying cable and 15cm after laying of cable and punned to 18cm after laying of cable and cover for protection of underground cable complete all as specified and directed. Notes :- (i) Approved dry sand free from vegetation, grass and other deleterious substances shall be used. (ii) For the purpose of payment only punned thickness shall be measured for payment.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 50 sqmm 3.5 core laid in trenches/ducts, through pipe, under floors or roads/along poles including taking out old unservceable cable complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 35 sqmm 3.5 core laid in trenches/ducts, through pipe, under floors or roads/along poles including taking out old unservceable cable complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 25 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/along poles including taking out old unservceable cable complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 16 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/along poles including taking out old unservceable cable complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 10 sqmm 2 core laid in trenches/ducts, through pipe, under floors or roads/along poles including taking old unservceable cable complete all as specified and directed. Note for item No. 26.00 to 30.00 : Excavation, sand cushioning, cable protection & GI pipe where usged shall be measured & paid for seperately under relevant items.

Galvanized steel water tubing light grade of 40mm bore with & including all fittings with clamp of 25x3mm flat iron welded to pipe fixed to wall/pole/ceiling or laid in floor or under road including taking out old unservceable pipe complete all as specified and directed.

Galvanized steel water tubing light grade of 50mm bore with & including all fittings with clamp of 25x3mm flat iron welded to pipe fixed to wall/pole/ceiling or laid in floor or under road including taking out old unservceable pipe complete all as specified and directed.

Bracket made out of 40mm bore galvanized steel tubing medium grade 1.50m long including bending if required as direct, 02 Nos clamps made out of MS flat iron 40x6mm of including suitable size fixed with bolts, nuts and washer including drilling holes and grouting with the same for fixing bolts including taking down old unserviceable complete all as specified and directed.

Cable route indicator comprising of CI wiser of size 100mm dia embossed as HT/LT power cable fixed to MS angle iron of size 50x50x6mm graded stone aggregate of block size 300x300x450mm including two coats of aluminium paint over a coat of aluminium red oxide primer and necessary earth work complete all as specified and directed.

Boring Hole/Drilling (Horizontally) under the road / pavement / hard standing with the help of trenchless and necessary machine for inserting Galvanised steel pipe of size 100/80mm not less than one metre below ground level complete all as specified and directed. Note : GI pipe shall be measured and paid for seperately in respective items.

Pre Stressed concrete Pole 9.00mtr long, 102mm x 152mm at top and 102mm x 289mm at bottom, class 10 complying with requirements of IS-1678-1978 including painting of poles with two coats of synthetic enamel paint over a coat of primer with black and white strips 30cm wide each upto 1.5mtr height from top of PCC foundation block and numbering of poles, including disconnecting & taking down old unserviceable broken RCC Pole complete all as specified and directed. Note: (i) Excavation in trenches in any types of soil, returning filling in and well ramming including watering and disposal of surplus soil to a distance not exceeding 50mtr from the starting points. (ii) PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in foundation bedding complete all as specified and directed. (iii) PCC (1:3:6) type C-2 using 40mm graded crushed stone aggregate as upto ground level complete all as specified. (iv) PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in coping including necessary form work complete all as specified and directed. (v) Painting of Pole upto 1.5mtr of height from coping level with alternative strip black and sky blue of width not less than 0.30 mtr and writing pole number with yellow shade on black base using synthetic enamel paint having height of words exceeding 5cm complete all as specified and directed. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions of this items.

Dismantling/taking down of old existing street light switching system and supply, fixing, connecting and testing of Automatic street light switch using infrared sensor based nature switch for automatic switching of street lights, nature switch operation should be based on natural light lux level. Required illumination level for switching on is <30 lux and for switching off >10 lux. The sensor should also have part night operation facility for 4-12 hours. The sensor alongwith suitable power contactor, incoming-outgoing MCBs should be enclosed in a pole/wall mounted enclosure made out of rust proof, electric shock proof, termite proof and FR grade SMC junction box conforming to IP-54. The circuit should be suitable enough to take 8 KW 3 Phase load with contactor 25 Amps conforming to IEC-60947-4-1/IS-13947-4-1 and incoming and outgoing MCBs of rating 32 Amps conforming to IEC-60898/IS-8828 and circuit wiring of minimum 10 sqmm copper conductor wire and including providing of 50x6mm flat iron clamp, necessary nuts and bolts, complete all as specified and directed. Make of nature switch - Model No Swadeep-02EC8kw3P of Kakatiya Energy System or equivalent make of Bajaj/Healer, Make for Contactor- BCH/L&T/Schneider, Make of MCBs- Hager/Schneider/L&T/C&S, Enclouser - Sintax or equivalent

Plain cement concrete (1:2:4) Type B-1 (using 20 mm graded granite stone aggregate) as in copping of poles, path to LT panels, bollard light (bollard lights to be refixed after repair to base) and other indicated work including necessary form work and finished the surface and including dismantling of old PCC complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No. 3 of SSR Part-I and connection to main switch board/Test point/ panel/ equipment and testing on completion including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exceeding 50 metre, charcoal and salt in alternate layer 15cm thick all around the earth plate electrode, Mild Steel Funnel with wire mesh, 20mm bore, GI pipe medium grade, 1.50 metre long for watering and 15mm bore, GI pipe light grade, 7.50 metre long for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:2:4) type B-1, using 20mm graded stone aggregate with angle iron 40x40x5mm frame 60mm thick RCC cover with 6mm steel bars 100mm centre to centre both ways etc including dismantling & taking out old existing unserviceable earthing complete all as specified & as directed. Note : (i) PCC chamber shall be constructed at least 1.5 mtr away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) If earth resistance of earthing is not found satisfactory it will be redone by the contractor on his risk and cost.

Earthing complete with galvanished earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5 deep below normal ground level and connected to galvanished iron earth lead strip 32mmx6mm upto 7.50 metre, by means of GI nuts, bolt, check nuts, washers, thimbles, etc as shown in electrical plate No. 5 SSR Part-I and connection to main switch board or panel and testing on completion including excavation and earth work in any type to soil, returning fitting in and removal of surface spoil to a distance not exceeding 50 metre, PCC chamber (1:3:6) type C-2, charcoal and salt mixed layer 15cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe light grade 20mm bore for watering and 50mm bore GI pipe light grade for earth wire protection fixed with poles with two clamps, made from earth lead strip 32mm x 6mm, bolts, nuts and washers, 80mm thick pre cast RCC cover 1:2:4, type B-1, reinforced with hard drawn steel wire fabric wieghing not less than 4 Kg/Sqm in lieu of CI cover etc including taking down old earth complete all as specified and directed. Note : (i) The unit rate shall be deemed to included for Test point, 32mmx6mm GI strip from top of the earth plate upto 7.50m above ground level. In case, GI protection pipe required is less than 7.50m, no price adjustment shall be made. (ii) PCC pit shall be provided at least 500mm away from the earth pit and not just on the earth pit and extra cost of additional length of water pipes and fittings, junctions, elbow etc shall be deemed to be included in the unit rate quoted by the tenderer.

Disconnecting, dismantling of old unserviceable LT panel and Design, supply, erection, commissioning and testing of outdoor type LT Panel, platform mounted, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos stepped type main copper bus bars of 400 Amps, looping & branch connection system with suitable rating copper bus bar having sleeves of colour coded. Chamber painted with powder coated paint (Shade : RAL-7032) after 9 tank pre-treatment of surfaces. LT Panel provided with suitable Neoprene rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947, IS 8623 Part-I, II III as amended. LT Panel made out of 3.15mm thick CRCA mild steel sheet and 3.00mm thick gland plate, front door (02 layers) and rear Door (01 layer) opening facility and 4 side slanting canopy type roof on top and mild steel channel (75 MC) base frame at bottom. All incoming MCCBs shall be marked with location and rating of MCCBs. The Feeder Pillar shall be provided with ventilation facility in the form of louvers for better heat dissipation in and including dismantling of old unserviceable LT Panel complere and including the followings :

Serial item No. 41.00 (Contd...) CONTROL WIRING : All control wirings shall have to be carried out with 1100 volts rated FR grade PVC insulated multi-flexible type copper wire of cross sectional area 1.50Sqmm and shall be properly bunched, tied and dressed, ferrule marked for proper identification and crimped with suitable size and type of tinned copper lugs and shall be wrapped with PVC spring type tube near the door hinges. CABLE ALLEY- Cable alley shall be provided in both side of the panel of suitable space for all incoming and outgoing cables. Cable terminals shall be provided for conecting of all incoming and outgoing cables. INCOMING :- (i) MCCB 200 Amps, 4 pole, 415 volts grade, rupturing capacity 25 kA, AC supply, 50 Hz, electronic release and making connections using suitable size copper lugs/thimbles and crimping tool - 01 Nos OUTGOING :- (i) MCCB 63 Amps, 4 pole, 415 volts grade, rupturing capacity 16 kA, AC supply, 50 Hz, thermal magnetic release and making connections using suitable size copper lugs/thimbles and crimping tool - 05 Nos (ii) MCB, SPN, rupturing capacity 10 kA, 32 Amps, 415 Volts - 01 Nos (iii) Power Contactor four pole with coil valtage 230 volt of capacity 25 Amp, 50 cycles - 01 Nos (iv) Timer switch microover analog - 01 Nos. (iv) Digital volt meter 96mm x 96mm suitable to read 0 to 500 volts, accuracy class 1% - 01 Nos (v) Digital Ammeter 96mm x 96mm suitable to read 0 to 630 Amps, accuracy class 1% - 01 Nos (vi) CT of rating 200/5, tape wound, rated burden 5 VA - 03 Nos (vii) LED indicator lamps complete with integral circuit and cluster LED, suitable to operate in 230-240 Volts AC supply - 1 Set of 03 Nos (Red, Yellow, Blue) (viii) Control fuse holder, made of bakellite, 16 Amps rating, stud type, pannel door mounting complete with 01 No 02 Amps HRC fuse of suitable type - 03 Nos

Serial item No. 41.00 (Contd...) OUTGOING :- (ix) Copper bus bar 20mm wide, 5mm thick of suitable length duly mounted on FRP bus bar insulators and marked with standard colour coded sleeves/tapes for all outgoing MCCBs - 04 Nos (ix) LED Pilot Lamp of following colours : (i) RED - 01 No, YELLOW - 01 No, BLUE - 01 Nos (x) Danger Notice Plate -02 Nos (xi) Pannel box made up of CRCA mild steel 3.15mm thick, duly powder coated with busbar and internal wiring all as per CPRI approved, Make of Panel - Universal Switchgear Control/POWERTECH SWITCHGEARS (I) PVT LTD (POWERTECH)/C&S ELECTRIC LIMITED (C&S)/HENSEL ELECTRIC INDIA PVT LTD/BCH ELECTRIC LIMITED/JOHN ELECT CO PVT LTD (JOHNS) Note : Panel will be manufactured by CPRI approved firm as indicated above. The contractor shall submit drawing of the panels to Engr-in-charge before procurement of LT panel for approval alongwith CPRI approval. Foundation will be prepared as per instructions of manufacturer and cost of foundation deemed to be included in the quoted rates.

Disconnecting, dismantling of old unserviceable LT panel and Design, supply, erection, commissioning and testing of outdoor type LT Panel, platform mounted, suitable for 3 phase 4 wire, 415 volts AC supply and having 4 Nos stepped type main copper bus bars of 200 Amps, looping & branch connection system made with suitable rating copper bus bar having sleeves of colour coded. Chamber painted with powder coated paint (Shade : RAL-7032) after 9 tank pre-treatment of surfaces. LT Panel provided with suitable Neoprene rubber gasket to make it completely dust and vermin proof and degree of protection not less than IP-55 and general construction conforming to IS : 13947, IS 8623 Part-I, II, III as amended. LT Panel shall be made out of 3.15mm thick CRCA mild steel sheet and 3.00mm thick gland plate , front door (02 layers) and rear Door (01 layer) opening facility and 4 side slanting canopy type roof on top and mild steel channel (75 MC) base frame at bottom. All incoming MCCBs shall be marked with location and rating of MCCBs. The Feeder Pillar shall be provided with ventilation facility in the form of louvers for better heat dissipation in and including dismantling of old unserviceable LT Panel complere and including the followings : CONTROL WIRING: All control wirings shall have to be carried out with 1100 volt rated FR grade PVC insulated multi-flexible type copper wire of cross sectional area 1.50 Sqmm and shall be properly bunched, tied and dressed, ferrule marked for proper identification and crimped with suitable size and type of tinned copper lugs and shall be wrapped with PVC spring type tube near the door hinges. CABLE ALLEY- Cable alley shall be provided in both side of the panel of suitable space for all incoming and outgoing cables. Cable terminals shall be provided for conecting of all incoming and outgoing cables.

Serial item No. 42.00 (Contd...) INCOMING :- (i) MCCB 100 Amps, 4 pole, 415 volts grade, rupturing capacity 25 kA, AC supply, 50 Hz, thermal magnetic release and making connections using suitable size copper lugs/thimbles and crimping tool - 01 Nos OUTGOING :- (i) MCCB 63 Amps, 4 pole, 415 volts grade, rupturing capacity 16 kA, AC supply, 50 Hz, thermal magnetic release and making connections using suitable size copper lugs/thimbles and crimping tool - 02 Nos (ii) MCB, SPN, rupturing capacity 10 kA, 32 Amps, 415 Volts - 01 Nos (iii) Digital volt meter 96mm x 96mm suitable to read 0 to 500 volts, accuracy class 1% - 01 Nos (iv) Digital Ammeter 96mm x 96mm suitable to read 0 to 630 Amps, accuracy class 1% - 01 Nos (v) Current transformer of rating 200/5, tape wound, rated burden 5 VA - 03 Nos (vi) LED indicator lamps complete with integral circuit and cluster LED, suitable to operate in 230-240 Volts AC supply - 1 Set of 03 Nos (Red, Yellow, Blue) (vii) Control fuse holder, made of bakellite, 16 Amps rating, stud type, pannel door mounting complete with 01 No 02 Amps HRC fuse of suitable type - 03 Nos

Serial item No. 42.00 (Contd...) OUTGOING :- (viii) Copper bus bar 20mm wide, 5mm thick of suitable length duly mounted on FRP bus bar insulators and marked with standard colour coded sleeves/tapes for all outgoing MCCBs - 04 Nos (viii) LED Pilot Lamp of following colours : (i) Red/Yellow/Blue - Each 01 Nos (ix) Danger Notice Plate -02 Nos (x) Pannel box made up of CRCA mild steel 3.15mm thick, duly powder coated with busbar and internal wiring all as per CPRI approved, Make of Panel - Universal Switchgear Control/POWERTECH SWITCHGEARS (I) PVT LTD (POWERTECH)/C&S ELECTRIC LIMITED (C&S)/HENSEL ELECTRIC INDIA PVT LTD/BCH ELECTRIC LIMITED/JOHN ELECT CO PVT LTD (JOHNS) Note : Panel will be manufactured by CPRI approved firm as indicated above. The contractor shall submit drawing of the panels to Engr-in-charge before procurement of LT panel for approval alongwith CPRI approval. Foundation will prepared as per instructions of manufacturer and rate of fondation deemed to be included in the quoted rates.

AUTOMATION AND SWITCHGEAR CONTROL

star electricals

M/s Ramesh & Company

SANJOLI CONSTRUCTION COMPANY

Manisha Enterprises

Vinay Traders

Sai Ram Electricals and Refrigeration Works