Construction of Swimming Pool at Sports Stadium Collage Ground Banswara.

Amount

Swimming Pool Overflow from Two Length sides

POOL DIMENSIONS: 50.03M (L), 25 M (W) x 1.35 Avg. Water Depth (1.05 to 1.65 M)

VOLUME : 1690 M³

TURN OVER PERIOD : 4.5 Hrs

FILTRATION FLOW : 375 M³/Hr

FILTRATION VELOCITY : 40M³/Hr/M²

BALANCE TANK CAPACITY : 75M3 ( 7.5 m x 7.5 m x 3.0 m )

Filters (Vertical Type)

Supply, Installation, Testing and Commissioning of TOTALLY NON-CORROSIVE Filter made of Fibreglass and reinforced with

Bobbin wound polyester yarn.

Fitted with collector arms and diffusers made from

unplasticised PVC and Polypropelene.

Hub for holding the collector arms should be made of Stainless Steel.

Filter Diameter 2000 mm.

(The diameter should be minimum 2000mm as measured at any point of the Height On Straight).

Flanged Connection for inlet & outlet : 160mm

Manhole lid: 360 mm dia

Media Bed depth 1000mm

Working pressure 2.5kg/cm2, (37.5 PSI),

Test pressure 3.75 kg/cm2 (56.25 PSI).

Flow rate of 125 m³/hour at a specific velocity of 40m³/hr/m².

Filter to be supplied complete with lid in polyester resin and fibre glass,filter internals,manual air purge cap, for sand discharge, presure gauge. as per Direction of Engineer Incharge

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Manually operated 5 Valve batteries built entirely in PVC/PN-10 with 160mm flanged connections to filters.All manual or automatically driven valve manifolds are made with flanges for connections to filters as per DIN-2501 standard.as per Direction of Engineer Incharge

Butterfly valves also in PVC. Supports & Clamps made of SS Pipes

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Silica sand media for filter with granulometry between 0.4 and 0.8mm as per Direction of Engineer Incharge

Make : Indeginouse

Supply, Installation, Testing and Commissioning of Gravel for filter with granulometry between 1-2 mmas per Direction of Engineer Incharge

Make : Indeginouse

Supply, Installation, Testing and Commissioning of High flow plastic Horizontal Centrifugal pumps with Inbuilt strainer. as per Direction of Engineer Incharge

Body is made of cast Iron

Prefilter body in Cast Iron Basket made of stainless steel with lid Pre-filter is closed with knob system of easy acessibilty connection size 125 x 125 mm

Shaft : Made of AISI SS 304

Mechanical seal : made of graphite/Ceramic

Impeller : Made of HT 200 ,Capacity : 12.50 HP,Motor 3000 rpm, IP 55 , 50 Hz

Electrical Protection : IP55

Capable of delivering 125 m³/hr @ 16 m head and shut off head not exceeding 2.5kg/cm2

Duty 3 nos. 1 no. standby

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of The maxium system Flow rate shall not exceed the flow rating of any listed ( per IAPMO Listed) suction outlet cover installed 18" x 18" : Grate with frame in ABS plastic white color. VGB 2008 & UL. Total open area : 155.6 sq.in. Frame size : 18" x 18". Floor flow rate : 424 gpm @ 1.5 ft/sec as per Direction of Engineer Incharge

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Suction inlet in white ABS with cap internal 50mm glue connection

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of White ABS plastic bottom inlet for concrete with S.S. screws and regulable

flow. Max flow 5 m3/hr. Connection: Outside/ inside dia 50mm Glue

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Chemical Dosing system for pH and Chlorine

Supply, Installation, Testing and Commissioning of Electromagnetic dosing pump in Polypropylene, IP 65 protection.

Maximum Flow 10.0 lph at 5 bar.

0-100% manual flow adjustment.180 strokes / minute.

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Semi transparent polyurethane tank for feeding chemicals to the dosing pumps.200 lts capacity.

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Overflow Type Ladders

Supply, Installation, Testing and Commissioning of Overflow Commerical Pool Ladder Ø 43 mm x 1.2 mm tube in Stainless steel 316 shiny polish finishing , different kind of tread always fixed to the handrail with hiddin screws ,safety tread , 3 step ladder

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Overflow Commerical Pool Ladder Ø 43 mm x 1.2 mm tube in Stainless steel 316 shiny polish finishing , different kind of tread always fixed to the handrail with hiddin screws ,safety tread , 5 step ladder

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Grating

Supply, Installation, Testing and Commissioning of White Color Modular Gratings made in UV stabilized ABS. With Anti-spill design Snaps together on central spine thus enabling a flexible continuous run.45 units per meter, Ht.22 or 35 mm, width: 295 mm

Make:AtecPool Espana/Pentair/Aquastar/Certikin

UNDER WATER LIGHTS

Supply, Installation, Testing and Commissioning of 50 W, 12VAC LED Warm white underwater light, niche type with Electrolysed stainless steel body ( SS316) and niche in PP.

supplied 3.6 meter STOWHO7RN-F cable.

The light shall be fitted/ removed with the use of SS screws to avoid coming loose like push fit lights. The lights shall be CE compliant.

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Deck box made in white ABS with three threaded outlets.

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Flexible conduit for carrying cable from underwater light to deck box. 1.5Meter length, threaded ends 3/4" & PG-16

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Transformers for underwater lights, 300 VA. Step down to 220V to 12/14/16V , IP 67

Make:AtecPool Espana/Pentair/Aquastar/Certikin

MAINTENANCE ACCESSORIES

Supply, Installation, Testing and Commissioning of Anodised aluminum double vacuum head (950 mm width) with 1-1/2" connection with handle

with clip type

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Extensible handles for cleaning attachments in

anodized aluminium which can be adapted to the

entire range of cleaning equipment, brushes, leaf

skimmers and scoops.13 mts. Long

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Transparent blue Copolymer Floating vacuum hose 2" dia (50mm)

30 mtrs long. Including hose cuffs for connection to suction inlets.

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Deep bag net made in polypropelene and white

polyester netting clip type connection

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Surface net made in polypropelene and white

polyester netting clip type connection

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Curved brushes made in polypropelene for pool

basins and scum liners clip type connection

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Straight brushes with stainless steel bristles

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Reinforced aluminium telescopic handle 2.4 - 4.8M long

with clip type connection

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Algae Brush with Aluminium back and S. S. bristles, fixing with clip connection.

Make:AtecPool Espana/Pentair/Aquastar/Certikin

Supply, Installation, Testing and Commissioning of Test kit for free chlorine & pHMeasures pH, bromine / chlorine. Easy to read, more accurate scale. Includes 20ml (0.7 FI. Oz.) phenol red & OTO reagents. Reagent bottles equipped with safety tops, for extra security.

Make:AtecPool Espana/Pentair/Aquastar/Certikin

PLUMBING

Following specifications to be adopted

The pipe sizes are to be calculated on the basis of the following velocities.

RETURN LINE PIPE VELOCITY : 2.5M/SEC

OVERFLOW LINE PIPE VELOCITY : 0.8M/SEC

SUCTION LINE PIPE VELOCITY : 1.2 to 1.5M/SEC

All pipes shall be of ISI mark, Prince or Finolex or Supreme OF 10KG/CM2.

All uPVC valves shall be of minimum PN10 rating.

All standard fittings like bends, elbows, tees etc should be of similar rating of the pipes. However, in cases where special fittings are required and the same are to be fabricated on site due to non availability anywhere in the Indian market, then the contractor has to ensure that the fittings are fabricated of high grade chopped uPVC fibre/ rovings and should be capable of withstanding working pressure of atleast 10kg/cm2.

All pipes and fittings, including those fittings (specials) that are fabricated on site should be pressure tested to atleast 10kg/cm2 for 24 hours

All pipes shall be well supported with clamps or civil support, especially at joints.

Supply and Installation of following uPVC pipes 10 bar pressure with laying,fixing,jointing.

Ø 315 mm (10 bar)

Ø250 mm (10 bar)

Ø200 mm (10 bar)

Ø160 mm (10 bar)

Ø110 mm(10 bar)

Ø90 mm(10 bar)

Ø75 mm (10 bar)

Ø63 mm (10 bar)

Ø50 mm (10 bar)

Make : Supreme/Prince/Finloex

All standard fittings like bends, elbows, tees etc should be of similar rating of the pipes. However, in cases where special fittings are required and the same are to be fabricated on site due to non availability anywhere in the Indian market, then the contractor has to ensure that the fittings are fabricated of high grade chopped uPVC fibre/ rovings and should be capable of withstanding working pressure of atleast 10kg/cm2. Tee, Elbow, Reducer, Bush, Socket, End Cap, MTA/ FTA , in 16 bar pressure , bush etc

Bends

Ø 315mm, 250mm, 200mm, 160mm, 110mm, 90mm, 75mm, 63mm, 50mm

Elbows

Ø 315mm, 250mm, 200mm, 160mm, 110mm, 90mm, 75mm, 63mm, 50mm

Ø 315mm, 250mm, 200mm, 160mm, 110mm, 90mm, 75mm, 63mm, 50mm

Paddle Flange ( IN uPVC)

Ø 250 mm for overflow from channel & B.tank inlet

Ø 200 mm for overflow from channel & B.tank inlet

Ø 160 mm for inlets & backwash

Ø 315 mm from B.Tank to pump suction header

Ø 200 mm for Overflow of B.Tank

Ø 160 mm for drain pipe

Ø 63 mm for vacuum point ,B.Tank drain & make up

Ø 50 mm for B.Tank drain & make up

Ø 50 mm for cables

uPVC VALVES : All valves shall be of Make :PIMTAS/COROPLAST of minimum PN10 rating.

Butterfly valve with flange adaptor & backing ring of Ø 160 mm dia for Main drain

Butterfly valve with flange adaptor & backing ring of Ø160 mm dia for Inlet line

Butterfly valve with flange adaptor & backing ring including nuts & bolts of Ø200mm/Ø160mm dia for pump suction & delivery lines (set)

Butterfly valve with flange adaptor & backing ring including nuts & bolts of Ø 315 mm. From balancing tank to pump suction header

Ball valve solvent type of Ø 63 mm dia from Vacuum line, drain & make up

Flap type Non-return valves with assembly kit Ø 315 mm for pool balancing tank to pump suction header

Flap type Non-return valves with assembly kit Ø 160 mm for inlet pipe

Flap Type Non-return valves with assembly kit Ø160mm for backwash & pump discharge line

ELECTRICAL

Scope shall include -

Supply, Installation, Testing and Commissioning of Control panel and electrical/control wiring including providing and fixing dust and verin proof cubicle type motor control center fabricated from 16 S.W.G. for body, 14 S.W.G. for door as per IP52, duly powder caoted finish and comprising of adequate capacity MCBs,MCCBs, cyclic timer, overload relays, push button start, ameter, voltmeter, appropriate etched plastic idetification plate for each starter/switch colour coaded internal wiring from incoming main switch gear, starters, indicating lamps, phase preventer , heater for panel, fresh/exhaust air fan with filter . complete in all respects(For Filter -Recircualtion pump (04 nos.) , Dosing pumps ( 6 nos.) , Underwater light MCB ( 6 nos.) , RCCB for U/W Lights

Make : Mark Enginner

Rigid PVC conduit ( Heavy) color Ivory/Black

Make : AKG/ Polycab

All the electrical cables for Underwater lights 2 core PVC copper cable from junction/deck box to light panel.

3 core PVC Copper cable for dosing pumps 2.5 mm2

4 core PVC armoured Copper cable for Pumps 6.0 mm2

Make : Polycab/Havels

Perforated GI cable tray 1.6 mm thick , 40 x 150 x 40 mm width

Pipe support , in MS with Wall, Floor and celing suppot on every 2meter distance with primer and rubber cote on MS support and all pipes should be in proper rubber coted with colour code and Flow marking and indication as per Direction of Engineer Incharge

Pipe Support U Clamp, C Clamp, Wall and celling mount pipe support on every 2 meter distance, (As per direction of engineer incharge)

All Pipes and Supports in Proper color code with base primer cote 2 time and 2 time rubber paint and marking . (As per direction of engineer incharge)

Rubber mat for pump for anti vibration

Rubber Expansion Joints Neoprene lined single unfilled arch Intergral rubber flanges on both sides with split retaining rings (SRR)+ Control Unit ( CU), working pressure : 10 bar , Test pressure : 16 bar, temp. : -10 to 70 C, Medium : water

Pump discharge side Ø 150 mm ( N.B)

Filter Air discharge side Ø 50 mm ( N.B)

Make : RESISTOFLEX

Supply, Installation, Testing and Commissioning of The anchors shall be made of SS 316 and on either side of the pool.The anchors shall be made of SS 316 and suitable for a pool with 2 sides overflow

Make:AtecPool Espana/Pentair/Aquastar/Certikin

POOL TILES : INDIAN MAKE

Light Blue Tile 250 mm x 125 mm x 6.3 mm

Porcelain Tile 250 mm x 125 mm x 6.3 mm thickness color :White

Make : Endura Tiles

Black Tile 250 mm x 125 mm x 6.3 mm

Porcelain Tile 250 mm x 125 mm x 6.3 mm thickness color : Black (for LaneMarking)

Make : Endura Tiles

Orient/ New Blue Antislip Tile 250 mm x 125 mm x 6.3 mm

Porcelain Tile 250 mm x 125 mm x 6.3 mm thickness color : Orient/ New Blue

Make : Endura Tiles

Dark Blue Antislip Tile 250 mm x 125 mm x 6.3 mm

Porcelain Tile 250 mm x 125 mm x 6.3 mm thickness color : Dark Blue (for Lane Marking)

Supply and fixing of Porcelain Tile 250 mm x 125 mm x 6.3 mm thickness color: New Blue, Blue, Dark Blue, White, Black etc. as per requirement of site including Lane marking Tile, Antislip Tile & Joint Piece using cement based high polymer modified quick set tile adhesive (water based) conforming to IS 15477, using 5 kg adhesie per Sqm of tile area. in average 3 mm thickness complete.

Supervision of Erection & Commissioning with 6month consumable chemicals, TCCA 90 200Kg, Alginex-200Ltr, HCL- 500ltr, Soda Ash- 100kg, Alum-100Kg,

Algines

Soda Ash

Non Ferric alum

Bidder Name

Amount

Watermate Technologies Private Limited(GSTN-08AABCW0104H1ZS)

agarwal jagdish construction company pvt ltd(GSTN-08AAFCA0580P1ZD)

agarwal jagdish construction company pvt ltd

agarwal jagdish construction company pvt ltd