ADDN/ALTN TO BUING NO P-123(6QTR)AT DRDO TOWNSHIP AND P-17 (MI ROOM) IN DRDL AND RENOVATION OF EXISTING OLD ANNEX ALONG WITH TOILET AT SEMINAR HALL IN DRDLAND SANCTIONED WORK AT CAN(DP) COMPLEX UNDER GE RND KANCHANBAGH

Repair to potholes any depth, not exc 1 sq m each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25 mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal) complete all as specified and directed.

Preparing old black top surfaces with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bag to remove all loose dirt etc, and including applying evenly a priming / tack coat with bituminous primer of grade VG 10 at the rate of 5kg per 10 sq.m, complete all as specified and as directed.

Premixed bituminous semi dense ashphaltic concrete 30mm consolidated thickness, using paving bitumen of Grade VG - 30 as binder with 5.5% minimum binder content by weight of total mix and laying with mechanical paver, rolled and compacted with power road roller of 8 to 12 ton capacity to required camber and gradient, complete all as specified and as directed.

M & L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed.

Demolition of cement concrete of any description and in any position in kerbs not other wise specially provided for and removing debris outside MOD land, complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.(straight or curved) and finished exposed surfaces fair and even complete all as specified and as directed.

Preparation of new surfaces of brick, stone, concrete, asbestos or plaster surfaces of any description over 10cm girth or width, not otherwise described and applying two coat of synthetic enamel paint over a coat of priming paint (plaster coat) complete all as specified and directed.

Supply and fixing in repairs cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions

Supply and fixing in repairs metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC (1:2:4) (150x150x300mm) type B1 complete all as specified and directed

Supply and fix for Smart solar road studs of size 125mmx 125mm & 20mm thick and 50mm long 40mm dia stand with 6 Nos diode bulbs (3Nos each side) electronically operated and designed to operate automatically in darkness, powered from rechargeable nickel cadmium battery to be charged through solar cells, main frame cast aluminium with polycarbonate cover solar cells and yellow reflected polycarbonate cover on side, complete all as specified and directed. Make : 3M / AVERY / DARK EYE / SIGNTECH

Supply and fixing in repairs metal tubular dealineator made out of ABS round body fitted with 2 Nos 80 mm dia hight -90mm , solar panel 2.4V205 mA, battery :1.2V/1600 mAH Ni Mh LED's, Visibility 500mtrs Flashing rate around 60 to 100 times per minute and including embedding in PCC (1:2:4) (150x150x300mm) type B1 complete all as specified and directed

Material & Labour for premix bituminous macadam using 4 % binder (paving bitumen VG 30 Grade) by weight of total mix laid manually or with mechanical pavers (consolidated thickness 75mm or less), rolled and compacted to gradient and camber required with 8 to 10 tonne power roller all as specified and directed by Eingneer-in-Charge.

M&L for preparation of old surface of any description not other wise described over 10 cm width or girth and applying one coats of synthetic enemal paint (Black and Yellow) complete all as specified and directed

M&L for PU coated machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment (approved by GE) confirming to IS 15658-2006 of 60mm thickness, M-35 grade including laid over 50mm thick sand cushion bed and preparing the surface to uniform level to receive tiles complete all as specified and as directed.

Demolition Concrete in ground floors and paving's n exc 15 cm thickness (below or above ground level) and including of removal of debris at out side of MOD land all as specified and directed.

M&L providing 75mm thick plain cement concrete type C-1, (1:3:6) (using 20mm graded stone aggregate) as in surface of sub base etc complete all as directed.

M&L providing cement Concrete (1:2:4) type B1 (using 20 mm graded stone aggregate) as in coping, benching drains and surface channels etc including necessary from work and demolition of existing PCC work including removal of debris outside MOD land complete all as directed.

Demolishing brick work in cement mortar manually / by mechanical means includng stacking of serviceable materials and disposal of unserviceable materials disposal out side of MOD land leads as per direction of Engr -in- Charge

Brick work with common burnt clay F.P.S ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor 2nd floor level in all shapes and sizes in cement mortar (1:4 )completed

Providing Half brick masonry with common burnt clay F.P.S ( non modular ) bricks of class designation 7.5 in super structure above plinth level upto floor 2nd floor level in cement mortar (1:4)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster up to the height 7.0 M including disposal of rubbish to the dumping ground within 50 metres lead

M&L 15mm thick rendering in CM (1:6) on fair faces of brick work or concrete surfaces and finished the surface fair and even without using extra cement complete .

Rendering 15mm thick in cement mortar C:M 1:4 on external wall surfaces in two layers (First coat 10mm thick and second coat 5mm thick) including mixing of water proofing compound @ 2% by weight of cement only on top layer of plaster, finished even and smooth. (WPC will be measured and paid separetly).Note : upto height 2th floor, double scoffolding shall be used.

M&L 6mm thick cement plaster (1:3) ( 1 cement : 3 fine sand) on ceiling surface finished with a floating coat of neat cement and thick coat of lime wash on top of ceiling when dry for bearing of RCC slabs and beams

Distempering Two or more coats on new/ Priviously work over a coat wall primer with Ist quality acrylic distemper , having VOC ( Volatile Organic Compound) content less than 50 grams / litre of approved brand and manufacture of required shade and colour incluidngapplying 1mm thick wall care putty complete as per manufacturer's specification

Finishing wall New work ( Two or more coats applied @ 1.43 litre/ 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre / 10 Sqm with 100 % premium acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489 : 2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade ( Company Depot tinted ) with silicon additives

M&L for white washing on new work of ceiling surfaces (three or more coats) to give an even shade complete over plastered surface to prepare the surface even and smooth .

Distempering on old work ( wall/ ceiling) ( one or more coats) with 1st quality acrylic distember ( Ready mix ) having VOC content less than 50 grams/ litre of approved brand over a coat of water thinnable cement primer and manufacturer to give an even shade

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface and Removing water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and fixing in repair water closet squatting pan ( Indian type WC pan) with 100mm sand cast iron P or S trap, 10 litre low level white PVC flushing cistern including flush pipe, with manually controlled device ( handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :- (i) white vitreous china orrissa pattern WC, pan of size 580 x 440 mm with integral type foot rests Make:- HINDWARE / NYCER / PARRYWARE / CERA

Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineerin-Charge. (a) Internal Work- Exposed on wall

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes 15 mm nominal dia , having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes 20 mm nominal dia , having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. Exposed on wall ,This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. and Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineerin-Charge.

Taking out doors, windows and clerestory window shutters ( steel or wood) including stacking within 50 metres lead :- (i) of area 3 Sqm and below

S&F 125x60mm Pressed steel frames for doors with one or more rebates including lugs etc., complete, as specified and directed.

S&F 105x60mm Pressed steel frames for doors with one or more rebates including lugs etc., complete, as specified and directed.

Providing and laying cement concrete in retaining walls, return walls ( any thickness) incluidng attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, sunken floors etc upto floor five level excluding the cost of centering shuttering and finishing :- (i) 1:2:4 (1 cement : 2 coarse sand ( zone -III) derived from natural sources : 4 graded stone aggregate 20mm nominal size derived from natural sources )

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing wire gauge shutters using galvanised MS wire gauge of average width of aperature 1.4mm in both directions with wire of dia 0.63mm, for doors , windows and clerestory windows with hinges and necessary screws :- (i) 35mm thick shutter withISI marked MS pressed butt hinges bright finished of required size second class rad wood kiln seasoned

Providing and fixing factory made door frame ( single rebate ) made out of single piece extruded solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 62mm width & 32mm thickness , frame will be mitred & jointed with self driven self tapping screws of size 38mm x 4mm & PVC solvent cement including fixing the frame to wall with suitable dia & length anchor fastener as per manufacturer's specification and direction of engineer -in- Charge.

Providing and fixing factory made 30mm thick door shutter made of solid PVC fooam profile. The styles & rails shall be of size 75mm x 30mm having wall thickness 5mm. The styles, top & bottom rails shall have one side wall thickness of 15mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with MS tubes of size 33mm x 17mm x 1mm, painted with primer, all four corners of reinforcement to be welded or sealed. solid PVC extruded bidding ( push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5mm PVC sheet as panel. The styles and rails will be mitred cut and joint with help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100mm x 30mm with wall thickness 5mm & 15mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8mm complete as per manufacturer's specifications and direction of Engineer -in- Charge. (i) Decorative finish ( both side wood grained finish)

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : size 125x65x2.12 mm

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete : 100x58x1.90 mm

Providing and fixing aluminium handles 150 mm , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc complete

Providing and fixing aluminium sliding door bolts 300 x 16mm and hasp, staple (bolt type), ISI marked anodised ( anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nut and screws etc complete

Providing and fixing aluminium tower bolts 150 x 10mm, ISI marked, anodised ( anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc complete

Providing and fixing aluminium Twin rubber stopper hanging floor door stopper, ISI marked, anodised ( anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade , with necessary screws complete

Providing and fixing steel E165 (Fe 290) confirming to IS 2062 -2006 work in gratings, frames, guard bars, ladders, railing, brackets, purlings, gates and similar works welded in built up sections / frames work, including cutting, hoisting, fixing in position and applying priming coat of approved steel primer using structural steel as required

Painting on new steel surface ( two or more coats ) including a coat of approved steel primer ( red oxide primer) with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade

Providing and laying rectified Glazed Ceramic non skid floor tiles of size 300x300mm or any size, more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar (1:4) (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified tiles size 600 x 600mm in floor in different size ( tbhickness to be specified by the manufacturer ) with water absorption less than 0.08 % and conforming to IS : 15622 of approved brand & manufacturer, in all colours and shade , laid on 20mm thick cement mortar (1:4) jointing with grey cement slurry @ 3.3 kg/Sqm incluidng grouting the joints with white cement and matching pigments etc. the tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, levelling system and rubber mallet for placing the tiles gently and easily.

Providing and laying vitrified tiles in different sizes ( size of tiles 600 x 600 mm) ( thickness to be specified by manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours & shade , in skirting, riser of steps , over 12mm thick bed of cement mortar (1:3) ( 1 cement : 3 coarse sand), jointing with grey cement slurry @ 3.3 Kg / Sqm including grouting the joint with white cement & matching pigments etc complete

Providing and laying Polished Granite stone flooring kitchen platform in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for window cill, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels and Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble

Providing and fixing brass curtain rods of wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 20 mm diameter.

Providing and fixing in repair Stainless Steel A ISI 304 (18/8) kitchen sink,Kitchen sink with drain board, 510x1040 mm bowl depth 250 mm , as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required , waste pipe and making good disturbed portion in CM 1:3 or PCC 1:2:4 as directed by Engineer-in-Charge.

S&F Stainless steel plate rack of size 910x 750x 300mm complete all as specified and directed. (Cat No : P-348 of Prayag or equivalent)

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangements of approved quality and colour 600mm long

Disconnecting damaged over head / terrace PVC water storage tank of any size from water supply line and removing from the terrace incluidng shifting at ground level as per direction of Engr -in- Charge

Providing and placing on terrace ( at all floor leels) polyethylene water storage tank, 1000 ltr capacity Is: 12701 marked , with cover and suitable locking arrangements and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing in repair gun metal gate valve 20mm nominal bore with CI wheel of approved quality ( screwed end) complete

Providing and fixing in repais wash basin with CI brackets, 15mm CP brass pillar taps, 32mm CP brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required :- (i) White vitreous china flat back wash basin size 550 x 400mm with single 15mm CP brass pillar tap

Providing and fixing in repairs 600 x 450 mm beveled edge mirror of superior glass ( of approved quality0 complete with 6mm thick hard board ground fixed to wooden cleats with CP brass screws and washers complete . Make:- COMMANDER PATTERN / (MANGOLD)/ JASMINE/ GOLDEN FISH

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore each

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :100 mm diameter

Providing and fixing in CP brass angle valves 15mm nominal bore for basin, mixed, geyser, urinal etc points of approved quality conforming to IS 8931

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing uplasticised PVC connection 15mm nominal bore x 60 cm length pipe with PTMT nuts, collar and bush of approved and colour

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

M/L for 100 mm thick 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mmin sub base nominal size derived from natural sources)

Chequerred precast cement concrete tiles 22mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc complete on 20mm thick bed of cement mortar (1:4) ( 1 cement : 4 coarse sand) :- (i) Light shade pigment using white cement

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m in ordinary rock.

Removing excavated soil to a distance n.exceeding 50m and depositing where directed at level n.exc 1.5m above starting pont complete all as specified and directed

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Hardcore of gauge exc 63 mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 75 mm thick with 20 mm nominal size stone aggregate

Steel reinforcement Thermo-Mechanically Treated bars of grade Fe-500D or more for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level

Steel reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete above plinth level. 5.22C.1 Thermo-Mechanically Treated bars of grade Fe-500D or more

Providing and laying in position ready mixed or site batched design mix cement Concrete of M25 grade All works upto plinth level with minimum cement content of 330 kg /cum for reinforced cement concrete work as in foundattion using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

All as per srl item No.81 but as in columns, lintel beams, etc above plinth level

All as per srl item No.81 but as in suspended floors, roofs, landings, balconies and access platforms above plinth level

Centering and shuttering including strutting, propping etc. and removal of form work for Foundations, footings, bases for columns

All as per srl item No.84 but as in suspended floors, roofs, landings, balconies and access platforms.

All as per srl item No.84 Lintels, beams, plinth beams, girders, bressumers and cantilevers

All as per srl item No.84 Weather shade, Chajjas, corbels etc., including edge

M&L Brick work with clay flyash F.P.S. (non modular) brick of class designation 7.5 in superstructure above plinth level up to floor five level in Cement mortar 1:6 (1 cement : 6 coarse sand)

M&L Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in cement mortar 1:4 (1 cement : 4 coarse sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth. Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives on New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm complete all as specified.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin-Charge

Providing and fixing to existing door frames 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron) shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) , EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item)

Providing and fixing 100x75x3.50 mm ISI marked, IS : 1341, M.S. heavy weight butt hinges with necessary screws etc. complete

Providing and fixing 250 x 10 mm aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing 125mm aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing 15 mm dia nominal bore G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :

Providing and fixing 20 mm dia nominal bore G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall complete

Providing and fixing 25 mm dia nominal bore G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall complete

Providing and fixing 25 mm nominal bore gun metal gate valve with C.I. wheel of approved quality (screwed end)

Providing and fixing counter wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require , White Vitreous China Flat back wash basin size 550x 400 mm with pair hot and cold of 15 mm C.P. brass pillar tap.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required , Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing square-mouth S.W. gully trap class SP-1 180x150 mm size P type complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing soil, waste and vent pipes 100 mm diameter Sand cast iron S&S pipe as per IS: 1730

Providing and fixing plain bend of required degree 100 mm diameter Sand cast iron S&S pipe as per IS: 1729

Providing and fixing uplasticised PVC connection pipe with brass unions 15 mm nominal bore 45 cm long.

Providing and fixing PTMT grating circular type of approved quality and colour 125 mm nominal dia with 25 mm waste hole.

Providing and placing PVC tripple layer water tank on terrace (at all floor levels) , IS : 12701 marked, with cover , tank connector and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes including fittings and fixtures complete all as specified and directed.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

S&F framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders framed balusters, walk ways conforming to Fe-410-0 or Fe-310-0

Providing and fixing 18 mm thick Granite stone slab colour black, Cherry/Ruby red gang saw cut, mirror polished, premoulded and prepolished, Area of slab over 0.50 sqm, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing edge moulding to 18 mm thick granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Providing and fixing on slab face unplasticised Rigid PVC 75 mm diameter water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Providing and fixing Coupler 75 mm

Cement concrete 1:2:4 ( 1 cement ; 2 coarse sand : 4 Graded stone aggregate 40mm nominal size ) in pre cast pavements, laid in required slope and camber in panels as required including consolidation finishing and tamping complete

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M&L for point wiring complete with 1.5 Sqmm PVC insulated unsheathe multistranded FRLS copper conductor 1100 V grade drawn throught and including 20 mm dia PVC conduit, medium grade and conduit accessories, concealed in the walls/ceiling and terminated to sunken metal box of modular type and including provision of GI modular box ISI marked in the walls suitable switches,sockets etc.,and including modular white lates for fixing modular switches,sockets/regulators etc., including 1.5 sqmm PVC insulated unsheathed multi-stranded FRLS copper conductor cable as earth continuity conductor and connecting to common earth dolly with brass screws, washers, copper lugs etc., complete all as specified and directed for one light . fan point /bell point/ bel point/ceiling fan / exhaust point controlled by one, one -way switch 5 Amps .

All as per SL item No.121 here-in- before One 3 pin 5/6 Amps socket outlet point on independent board controlled by one one way 5/6 Amp switch, complete.

d) All as per SL item No.121 here-in- before but for One 3 pin socket outlet 5/6 Amps socket outlet point on same board controlled by one one-way 5/6 Amps switch, complete.

M&L for point wiring complete with 4.0 Sqmm PVC insulated unsheathe multistranded FRLS copper conductor 1100 V grade drawn throught and including 20 mm dia PVC conduit, medium grade and conduit accessories, concealed in the walls/ceiling and terminated to sunken metal box of modular type and including provision of GI modular box ISI marked in the walls suitable switches,sockets etc.,and including modular white lates for fixing modular switches,sockets/regulators etc., including 4.0 sqmm PVC insulated unsheathed multi-stranded FRLS copper conductor cable as earth continuity conductor and connecting to common earth dolly with brass screws, washers, copper lugs etc., complete all as specified and directed for 3-pin 15/16 Amp socket outlet point t board, complete.

Supply & Fixing Modular switch, one module, one way 6 Amp, 230V, complete all as specified and directed.

Supply & Fixing Modular switch 16A, one module, 230 Volts, complete all as specified and directed.

Supply & Fixing Modular step type, fan regulator, two module, 230 Volts, complete all as specified and directed.

Supply & Fixing socket out let 6 Amps, 230 volts AC 3 pin multipurpose type complete as directed.

Supply & Fixing modular socket, 6A/16A - 230V Multipurpose complete

S&F ceiling rose two to three terminal surface backallite type AC 50Hz 230 volts complete

S&F LED lights fittings 1x20W,220V,AC decorative box type with driver holder including LED tube light connecting up with three coreflexible copper conductor cable of suitable size from ceiling rose complete,including connecting up with twin core flexible copper conductor cable with sutable size

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 Watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fix 415 V 10 KA 'C' curve miniature circuit break (MCB)of TPN 40-100 amps current carrying capacity in the DB complete with connection testing and commissioning

S&F sheet metal enclosure MCCB DB TPN double door type AC 415 V 4 way with 200 Amps rated bus bar, vertical type with MCCB 63 A 4 pole 10 KA as in comer flush to wall including taking down old one complete and making good of distructed surface including taking down old one complete

Earthing complete with Gi earth plate electrode 600x600x6mm buried directly in ground vertically to a depth of not less than 2.25 mtr belowground level than 1.5 mtr below ground level connected to GI earth wire 4 mm dia by means of bolts washers etc made out of GI earth wire will be protected by galvanized iron pipe light grade 15 mm bore up to main distribution board/main switch including necessary excavation and earth work PCC 1:3:6 type CI (using 20 mm graded stone aggregate) RCC cover 1:2:4 type B1 including necessary reinforcement etc complete all as show electric plate No. 3 of MES such part-I complete

S&F indoor industrial type surface/wall mounted LED integral batten 20W, 6500K CCT, alluminium extruded body and polycarbonate diffuser, <10%THD, integral elctronic driver complete fixing with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed. Make : Havells/Polyycab/Philips/Wipro

Material and labour for point wiring complete with ISI marked 1.5 Sqmm PVC insulated multistranded single core cable with copper conductor (FRLS) 1100 volts grade drawn through and including PVC rigid conduit 20 mm or higher dia ISI marked as required at site including conduit accessories such as Modular plate, suitable gang boxes,Junction Boxes, Inspection Covers etc, concealed/surface type on stone/brick masonry walls, roofs, floors etc by means of saddles and clamps etc including PVC gang boxes as required at site for concealed/surface conduit wiring and modular plates & covers as required at site for housing switches sockets, regulators etc. including providing of 1.5 Sqmm PVC insulated multistranded unsheathed FRLS copper conductor as earth continuity conductor and connecting to common earth dolly all as specified for and connecting up complete for the following:- One light/ fan point controlled by one, one way switch

Supplying and fixing 6 way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required.

Supply and Fix MCB DP 40 A, 240 V, 'C' curve

Supply and fixing MCB SP 5 to 32 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver.

Supply, laying & testing PVC insulated, PVC sheathed cable galvanized steel strip or wire armoured, electric control cables (Heavy duty) with stranded copper conductor of size 2.5 sqmm, 3 core, 1100 Volts grade.

S&F GI tubing 25 mm dia medium grade complete including fittings, excavation, refilling and removal soil all as specified and directed.

Please Enable Macros to View BoQ information