Construction of 1 No. Type-IV residential quarter for Assistant Engineer Padhar District Mandi (H.P.)

Amount

Excavation in foundation, trenches, etcetera in earth work in all kinds of classification, of soils such as pick work, jumper work, blasting work saturated soils including chiseling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals, lift up to any height stacking excavated soil up to all leads and lifts clear from the edge of excavation and then returning the stacked soil in 15cm (fifteen centimetre) thick layer when required into plinths, sides of foundation etcetera consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth to the disposal point within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Excavation in drains and channels etcetera in earth work in all kinds of classification of soil such as pick work, jumper work, blasting work, saturated soil including chiselling or any other mixed variety of soil dewatering and / or removal of slush and other incidentals, lifts upto any height, stacking the excavated soil upto all leads and lifts clear from the edge of excavation and then returning the stacked soil in fifteen centimeter thick layers when required into plinth sides of foundation etcetera consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth to the disposal point within all leads, lifts and carriage of material complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including with in all leads, lifts, carriage of material and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing form work with steel plates 3.15mm (Three point one five millimetre) thick welded with angle iron in frame 30x30x5mm (Thirty into thirty into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling upto all height and removal of the same for in-situ reinforced concrete and plain concrete work in :

Foundation, footings, bases of columns etcetera and mass concrete including carriage of materials within all leads and lifts and other incidentals complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Flat surface such as soffits of suspended floors, roofs, landings and the like upto any thickness including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttresses, plinth and string courses and the like including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Columns, pillars, posts and struts square, rectangular, polygonal in plan including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Stair cases with slopping or stepped soffits, excluding landing but including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Beam, cantilever, girders and lintels, sides and soffits of beam beams haunching cantilevers girders bressumers and lintels of any depth including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Edges of slabs and breaks in floors and walls of any width including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying cement concrete 1:6:12 ( one cement : six sand : twelve graded, crushed stone aggregate 40mm (forty millimetre) nominal size) curing complete excluding cost of centring and shuttering in foundation and plinth including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying cement concrete 1:4:8 ( one cement : four sand : eight graded, crushed stone aggregate 40mm (forty millimetre) nominal size) mechanically mixed and curing complete excluding cost of form work in foundation and plinth including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying cement concrete 1:3:6 ( one cement : three sand : six graded, crushed stone aggregate 40mm (forty millimetre) nominal size) mechanically mixed and curing complete excluding cost of form work in foundation and plinth including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying mechanically mixed and vibrated cement concrete 1:2:4 ( one cement : two sand : four graded, crushed stone aggregate 20mm (twenty millimetre) nominal size) to give a smooth and even surface including centering and shuttering etcetera but excluding cost of reinforcement in mouldings cornices windows sill etcetera exceeding 15cm (fifteen centimetre) in girth including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying reinforced cement concrete design mix M-25 (twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work. The mix shall be designed as per requirement of I.S. code and P.W.D. specification. The dedign mix shall be got approved from the Engineer-in-Charge prior to casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix as per I.S. code in foundation footing, bases of columns and the like mass concrete upto floor all level including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying reinforced cement concrete design mix M-25 (twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work. The mix shall be designed as per requirement of I.S. code and P.W.D. specification. The dedign mix shall be got approved from the Engineer-in-Charge prior to casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix as per I.S. code in suspended floor, roofs, landing and shelves and their support balconies beams girders, bressumers and cantilevers upto all floor level including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying reinforced cement concrete design mix M-25 (twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work. The mix shall be designed as per requirement of I.S. code and P.W.D. specification. The dedign mix shall be got approved from the Engineer-in-Charge prior to casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix as per I.S. code in columns, pillars posts and struts upto floor all level including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying reinforced cement concrete design mix M-25 (twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced concrete work. The mix shall be designed as per requirement of I.S. code and P.W.D. specification. The dedign mix shall be got approved from the Engineer-in-Charge prior to casting. The theoritical consumption of cement for the item shall be worked out as per approved design mix as per I.S. code in stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto all floor level including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying design mix M-20 (twenty) grade of cement concrete mechanically mixed and vibrated with minimum cement contents of 320 Kg/cum (three hundred twenty kilogram per cubic metre) with graded, crushed stone aggregate 20mm (twenty millimetre) nominal size and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:

In suspended floor, roofs, landing and shelves and their support balconies beams girders, bressumers and cantilevers upto all floor level including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

In walls any thickness but not less than 0.10mtrs. (zero point one zero metre) thickness including attached pilasters, buttresses plinth and string courses upto any depth /any height including curing complete and carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing Tor steel reinforcement for RCC work including bending binding and placing in position including cost of binding wire complete in all floors including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Second class half brick masonry in common burnt clay building bricks of approved kiln in foundation and plinth in mud mortar including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying precast cement concrete hollow block masonry in wall with cement concrete blocks of size 40cm x 19cm x 20cm (forty centimetre into nineteen centimetre into twenty centimetre) including quion block jamb blocks and closers etcetra made of cement concrete 1:3:6 (one cement : three sand : six graded, crushed stone aggregate 20mm (twenty millimetre) nominal size) laid with cement mortar 1:6 (one cement :six sand) and curing complete in super structure upto all floor level including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying precast cement concrete hollow block masonry in partition walls 10 cm (ten centimetre) thick with cement concrete hollow blocks of size 40cm x10cmx20cm (forty centimetre into ten centimetre into twenty centimetre) including quion block jamb blocks and closers etcetera made of cement concrete 1:3:6 (one cement :three sand : six graded/crushed stone aggregate 20mm (twenty millimetre) nominal size) laid with cement mortar 1:4 (one cement : four sand) including curing complete in super structure upto all floor level including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement : six sand : twelve graded, crushed stone aggregate 20mm (Twenty millimetre) nominal size) at plinth level in cement mortar 1:6 (one cement : six sand) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Square rubble masonry coursed with hard stone of approved quality in foundation and plinth including racking out joints in cement mortar 1:5 (one cement : five sand) and curing complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing second class deodar wood work in frames of doors, windows, clerestory windows and other frames wrought framed and fixed in position including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 40mm (forty millimeter) thick second class deodar wood panelled, glazed or panelled and glazed shutter including fixing of double glass with rubber gasket for doors, windows and clere story windows including black enamelled iron butt hinges with necessary screws including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 40mm (forty millimeter) thick second class deodar wood wire gauge shutters using galvanized M.S. wire gauge of IS gauge designation 85g (eighty five) gauge with wire of diameter 0.56mm (zero point five six millimeter) for doors, windows and clerestore windows including bright finished black enamelled iron hinges with necessary screws including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 19mm (nineteen millimetre) thick commercial board with hard wood lipping shutters for cup-boards etcetra including nickle plated bright finished piano hinges and carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 19mm (nineteen millimetre) thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails and screw etcetra complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing first class deodar wood 12mm (twelve millimetre) thick and 100mm (one hundred millimetre) wide pelmet with 25mm (twenty five millimetre) diametre wooden curtain rod and brackets including fixing with 25x3mm (twenty five into three millimetre) M.S flats 10 cm (ten centimetre) long and plugs etcetra complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing M.S. plain grills of required pattern and design in iron frames of windows etcetra with flats square or round bars with round headed bolts and nuts or by screws complete in all respect including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etcetera including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

300x16mm (Three hundred into sixteen millimeter)

Providing and fixing aluminium tower bolts (Barrel type) anodized transparent or dyed to required shade and colour with screws etcetera including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

250x10mm (Two hundred fifty into ten millimeter)

150x10mm (One hundred fifty into ten millimeter)

Providing and fixing mat finish aluminium handles anodized transparent or dyed to required shade and colour with necessary screws etcetera including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

125mm (One hundred twenty five millimetre)

100mm (One hundred millimetre)

Providing and fixing 150mm (one hundred fifty millimetre) oxidized MS single acting spring hinges with necessary screws including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 200mm (two hundred millimetre) oxidized MS hooks and eyes including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 100mm (one hundred millimetre) bright finished brass floor door stopper with rubber cushion screws etcetera to suit shutter thickness including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 50mm (fifty millimetre) bright finished brass cup board for ward robe knob including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing 40x3mm (forty into three millimetre) flat iron hold fast 40cm (forty centimetre) long including fixing to frame with 10mm (ten millimetre) diametre bolts, nuts and wooden plugs and embeding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimetre) 1:3:6 (one cement : three sand : six graded, crushed stone aggregate 20mm (twenty millimetre) nominal size) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing M.S. fan clamp Type-1 (one) of 16mm (sixteen millimetre) diametre bar bent to shape with hooked ends in RCC slab during laying including painting the exposed portion of loop, all as per standard design complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 10mm (ten millimetre) thick antiskid water proof stain and impact resistent heavy duty viterified tiles Nitco or equivalent 600x600x10mm (six hundred into six hundred into ten millimetre) manufactured of approved shade and colour in flooring treads of steps and landings laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete as per specification including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 10mm (ten millimetre) thick antiskid water proof stain and impact resistent heavy duty viterified tiles Nitco or equivalent 600x600x10mm (six hundred into six hundred into ten millimetre) manufactured of approved shade and colour in skirting and dado laid over 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete as per specification including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying spartic ceremic tiles 5.5mm (five point five millimetre) thick in flooring (300x300mm (three hundred into three hundred millimetre) size) treads of steps laid on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) finished with flush pointing in white cement including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

White glazed tiles 6mm (six millimetre) thick in skirting riser of steps and dado 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) and jointed with cement slurry complete upto all floor level including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying granite stone in flooring 20mm (twenty millimetre) (average) thicknees base of cement mortar 1:3 (one cement : three sand) laid over and jointed with grey cement slury mixed with pigment to match the shade of granite stone including rubbing and polishing complete 20mm (twenty millimetre) thick in all floors including curing and carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying 25mm (twenty five millimeter) thick Kota stone slab flooring 20mm (twenty millimeter) (average) thick base of cement mortar 1:4 (one cement : four sand) laid over and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as per specification including carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

40mm (forty millimeter) thick cement concrete flooring 1:2:4 (one cement : two sand : four graded,crushed stone aggregate 20mm (twenty millimeter) nominal size) laid in one layer finished with a floating coat of neat cement including curing, carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Cement plaster skriting 15mm (fifteen millimetre) thick (upto any height) with cement mortar 1:3 (one cement : three sand) finished with a floating of neat cement including rounding of junction with floor including curing, carriage of material within all leads, lifts and other incidental charges complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 40mm (forty millimetre) wide and 4mm (four millimetre) thick glass strips in joints terrazzo floors including carriage of materials within all leads, lifts and other incidental charges complete in all respect.

Providing and fixing 100mm (one hundred millimetre) diametre pipes on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5kg/sqm (four point five kilogram per square metre) including filling the joints with approved adhesive complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

PVC plain bend 100mm (one hundred millimetre) diametre

PVC plain corner type bend 100mm (one hundred millimetre) diametre

PVC shoe 100mm (one hundred millimetre) diametre

Providing and fixing PVC clamps 100mm (one hundred millimetre) diametre ISI marked of approved design with steel screws and rawl plugs complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint in gratings framed guard bars ladders, railings, brackets and similar works complete as per design including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing M.S. railing for stair case having balluster of 19mm x 19mm (nineteen millimetre into nineteen millimetre ) M.S. solid square bar with a clear height of 85cm (eighty five centimetre) jointed in cement concrete steps and welded with electrical/gas welding M.S. flat of 40mm x 6mm (forty millimetre into six millimetre) at top of vertical ballusters, the balluster welded / jointed with two number outer face M.S. flat of 40mm x 6mm (forty millimetre into six millimetre) complete with a applying priming coat of red lead paint complete as per specifications and design including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Applying Birla White wall care putty over plaster surface after thoroughly brushing the suface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the suface complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after throughly brushing the surface to remove all dirt loose powdered materials including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Painting two coats (excluding priming coat) on new steel and other metal surfaces under coat with ready mixed paint other than white brushing to give an give an even shade including cleaning the surface of all dirt, dust and other foreign matter including carriage of materials within all leads and lifts complete in all respect.

Applying priming coat over new wood and wood based surface after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting with ready mixed paint brushing wood primer pink including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Painting two coats (excluding priming coat) on new wood and wood based surfaces, with white enamel paint other than white to give an even shade including cleaning the surface of all dirt, dust and other foreign matter, sand papering and stopping including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

White washing with lime on undecorated ceiling and/or slopping roofs (two coats) to give an even shade including thoroughly brooming the surface to remove all dirt, dust mortar dirt and other foreign matter including carriage of materials within all leads and lifts complete in all respect.

6mm (six millimeter) thick cement plaster to ceiling with cement mortar 1:3 (one cement : three sand) including curing and carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

15mm (fifteen millimetre) cement plaster in single coat on the rough side of brick/concrete/stone walls for interior plastering upto floor all level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement : six sand) including curing and carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

15mm (fifteen millimetre) cement plaster in single coat on the fair side of brick/concrete/stone walls for interior/exterior plastering upto floor all level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement : six sand) complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

15mm (fifteen millimetre) cement plaster in single coat on the fair side of brick/concrete/stone walls for interior/exterior plastering upto floor all level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm (eighty millimetre) in girth and finished even and smooth in cement mortar 1:3 (one cement : three sand) complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

15mm (Fifteen millimeter) cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto floor all level including arrises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (eighty millimeter) in girth and finished even and smooth in cement mortar 1:3 (one cement : three sand) complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after throughly brushing the surface free from mortar droopings and other foreign matter and also including preparing the surface even and sand papered smooth on walls including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing plinth protection 50mm (fifty millimeter) thick in cement concrete 1:3:6 (one cement : three sand : six graded, crushed stone aggregate 20mm (twenty millimeter) nominal size including finishing the top surface of concrete smooth including curing complete and carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing under layer for plinth protection of 75mm (seventy five millimeter) thick (unconsolidated) bed of dry brick/stone aggregate 40mm (forty millimeter) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Constructing course rubble hammer dressed U-Shape open surface drain with side wall 15x22cm (fifteen into twenty two centimetre) in cement mortar 1:6 (one cement : six sand) and inside plastering with cement plaster 1:3 (one cement : three sand) including earth work and laying 10cm (ten centimetre) cement concrete in 1:5:10 (one cement : five sand : ten graded, crushed stone aggregate of 40mm (forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4 (one cement : two sand : four graded, crushed stone aggregate of 20mm (twenty millimetre nominal size) and finished with a floating coat of neat cement complete as per standard design including curing and carriage of material with in all leads, lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying of brick aggregate 50mm (fifty millimetre) nominal size in soak pit including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Water Supply and Sanitary Installation :- Providing and fixing to wall, ceiling and floor galvanized mild steel tubes (medium grade) tube fitting and clamps including making good the walls, ceiling and floor complete including carriage of material with in all leads, lifts and other incidentals complete in all respect as per direction and satisfaction of Engineer-in-Charge.

15mm (fifteen millimeter nominal size)

20mm (twenty millimeter nominal size)

Providing and fixing flat back 550x400mm (five hundred fifty into four hundred millimeter) vitreous china wash basin with single hole for pillar tap with CI or MS brackets painted white including cutting holes and making good the same but excluding fittings complete including carriage of material with in all leads, lifts and other incidentals complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 610 x 510 mm (six hundred ten into five hundred ten millimetre) with bowl depth 200 mm (two hundred millimetre) kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. brackets, painted white including cutting hole and making good the same but excluding fitting including carriage of material with in all leads, lifts and other incidentals complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing vitreous china padestal of approved specification/make for wash basin completerecessed at the back for the reception of pipe and fitting including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 32mm (thirty two millimetre) diametre C.P.brass waste of approved specification/make for wash basin or sink complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 600x450mm (six hundred into four hundred fifty millimetre) bavelled edge mirror of superior glass mounted on 6mm (six millimetre) thick AC sheet or ply wood sheet and fixed to wooden plugs with CP brass screws and washers complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 600 x 20mm (six hundred into twenty millimetre) CP brass towel rail complete with CP Brass brackets fixed to wooden plugs with CP brass complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 600x120mm (six hundred into one hundred twenty millimetre) glass self with CP brass brackets and guard rail complete fixed to wooden plugs with C.P. brass screws complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) diametre C.P.brass bib tap with capstan head complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 15mm (fifteen millimetre) diametre C.P. brass pillars tap with capstan head complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing brass angle valve 15mm (fifteen millimetre) without nut and pipes complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 100mm (one hundred millimetre) diametre C.P. brass shower rose with 15mm or 20mm (fifteen to twenty millimetre) inlet complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing PVC connection pipe with brass unions 300/450mm ( three hundred/ four hundred fifty millimetre) length 15mm (fifteen millimeter) nominal bore complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing brass full way valve with wheel complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

15mm (fifteen millimetre) nominal bore.

20mm (twenty millimetre) nominal bore.

Providing and fixing 20mm (twenty millimetre) PTMT concealed stop cock with flange of approved quality and colour complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing PVC 1000 (one thousand) litres net capacity water storage tank of ISI: 12701 marked, G.I. inlet and outlet connection, 15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level and including carriage of material with in all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipe ISI marked including jointing with approved adhesive etcetera including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

110mm (one hundred ten millimetre) diametre.

75mm (seventy five millimetre) diametre.

Providing and fixing PVC single equal branch with ovel access door, ISI marked insertion rubber washer 3mm (three millimetre) thick bolts and nuts complete including fixing with approved adhesive etcetera complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

110mm (one hundred ten millimetre) diametre.

75mm (seventy five millimetre) diametre.

Providing and fixing PVC door bend with ovel access door, insertion rubber washer 3mm (three millimetre) thick bolts and nuts ISI marked complete including fixing with approved adhesive etcetera complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

110mm (one hundred ten millimetre) diametre.

75mm (seventy five millimetre) diametre.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etcetera including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

110mm (one hundred ten millimetre) diametre.

75mm (seventy five millimetre) diametre.

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etcetera complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

110mm (one hundred ten millimetre) diametre.

75mm (seventy five millimetre) diametre.

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawl plugs etcetera complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

110mm (one hundred ten millimetre) diametre.

75mm (seventy five millimetre) diametre.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etcetera complete in all respect as per direction and satisfaction of Engineer-in-Charge.

110mm x 75mm (one hundred ten into seventy five) millimetre

Providing and fixing PVC cowl ISI marked including fixing with approved adhesive etcetera including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

110mm (one hundred ten millimetre) diametre.

75mm (seventy five millimetre) diametre.

Providing and fixing ordinary closet of approved shade Vitreous China wash down water closet (European type W.C. pan) with integral “P” or “S” trap including jointing the trap with soil pipe in cement mortar 1:1 (one cement :one sand) (seat and cover to be measured and paid for separately) complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing solid type white plastic sheet and cover for wash down water closet with C.P. brass hinges and rubber buffers complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing PTMT coloured/ white high density polyethylene / poly propylene 10 (ten) litres capacity (full flush) European standard control low level flushing cistern with fitting with a pair of brackets with fittings such as lead valve syphon, 15mm (fifteen millimetre) nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm (forty millimetre) diametre C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (over flow pipe to be measured and paid for separately) complete in all respect including carriage of materials within all leads and lifts as per direction and satisfaction of Engineer-in-Charge.

Constructing man hole with RCC top slab in 1:2:4 mix (one cement : two sand : four graded, crushed stone aggregate 20mm (twenty millimetre) nominal size) foundation concrete 1:4:8 (One cement : four sand : eight graded, crushed stone aggregate 40mm (forty millimetre) nominal size) in side plastering 15mm (fifteen millimetre ) thick with cement mortar 1:3 (one cement : three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two sand : four graded, crushed stone aggregate 20mm (twenty millimetre) nominal size) finished smooth complete including curing and testing inside size 800x800mm (eight hundred into eight hundred millimetre) and 500mm(five hundred millimetre) deep including CI cover with frame (light duty single seal pattern-I) 455x610mm (four hundred fifty five into six hundred ten millimetre) internal dimension total weight of cover and frame to be not less than 38 Kg. (Thirty eight kilograme) (weight of cover 23 Kg. (twenty three kilograme) and weight of frame 15 Kg. (fifteen kilogramme) with 300mm (three hundred millimetre) thick walls of squared rubble masonry coursed with hard stones of approved quality in cement mortar 1:3 (one cement : three sand) as per HP.PWD. specification and complete in all respect including carriage of materials within all leads and lifts and other incidentals as per direction and satisfaction of Engineer-in-Charge.

Supplying and fixing cast iron cover with frame for man holes 500mm (five hundred millimetre) internal diametre C.I. cover (medium duty) weight of cover with frame116Kg (one hundred sixteen kilogram) complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 200mm (two hundred millimetre) wide cast iron rungs with chequered or ribbed non slip surface including fixing in manholes with 200mmx200mmx100mm (two hundred millimetre into two hundred millimetre into one hundred millimetre) cement concrete 1:3:6 (one cement: three sand: six graded, crushed stone aggregate 20mm (twenty millimetre)nominal size) complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing grill jali panel on chamber including cutting, welding as per specifications and design including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Sushil Kumar

DUGLA RAM

PADAM SINGH

Balwant SIngh Thakur

KHEM CHAND