REPAIR TO BOUNDARY WALL RETAINING WALLS FENCING AND MISC BR WORKS AT SECTOR A UNDER AGE BR II OF GE 865 EWS

Amount

Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles/concrete block walling complete all as specified and as directed by Engr-in-Charge.

M&L for pre cast cement concrete block masonary of 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) with soild blocks, exc.10cm in width, set and jointed in cement mortor 1:6 complete all as spd and directed.

M&L for pre cast cement concrete block masonary of 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) with soild blocks, using old concrete blocks obtained from the demolition, exc.10cm in width, set and jointed in cement mortor 1:6 complete all as spd and directed.

Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and as directed.

Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6, using old stones/boulders obtained from the demolition complete all as specified and as directed.

M&L for raised pointing to random rubble masonry, uncoursed or brought upto courses in CM 1:4 complete all as specified and as directed.

Taking down cement plaster of any description on brick or stone walls, concrete surfaces including racking out joints, hacking for key, scrubbing down with water remove dust, debries/rubbish etc, complete all as specified and as directed.

Rendering 15 mm thick other than fair faces of brick work or stone masonary work, finished even and smooth (without using extra cement) on walls in cement mortar (1:4), complete all as specified and directed by Engr-in-Charge.

M&L for two coats cement base paint on newly plastered surfaces of wall including preparation of surfaces including curing before and after applying each coat complete all as specified and directed. MAKE : Snowcem/Asian/BERGER/DURACEM

M&L for one coat cement base paint on old plastered surfaces of wall including preparation of surfaces including curing before and after applying each coat complete all as specified and directed. MAKE : Snowcem/Asian/BERGER/DURACEM

Preparation of old decorated plastered surfaces of walls by complete remvoal of existing treatment and applying two coats of exterior emulsion paint of Make Apex (Asian) in any tint, over a coat of primer (as per manufacturer's instruction of Apex) over and including 2 mm thick coat of Birla white wall care putty, as on wall, roof projection, facias, chhajja, etc all as per manufacturer's instructions all as specified and directed by Engr-in-charge. MAKE: BERGER (WEATHER COAT ALL GUARD) / ASIAN (APEX ULTIMA) / NEROLAC (EXCEL TOTAL) / JEHNSON & NICHOLSON / DULUX ICI

M&L for one coat of oil emulsion tera cota on plaster, concrete and tilling surface complete all as specified and directed.

Material for factory made precast PCC (1:2:4) type B-1 using 20 mm graded crushed stone aggregates, as in kerb stone of size 300 x 300x 100mm thick (width and depth of kerb stone shall be 100mm & 300mm respectively) set in CM (1:4) inclduing necessary form works and earth work complete all as specified and directed by Engr-in-Charge.

M&L for one coat of plastic emulsion paint of any description on old plastered surfaces or concrete surface of any description over 10cm girth or width not other wise described, complete all as specified and directed by Engineer-in-Charge. Make : BERGER (SILK,RANGOLI,EASY CLEAN)/ASIAN (ROYALE)/NEROLAC (IMPRESSION)/ECOCLAN/DULUX ICI

M&L for two coats of plastic emulsion paint of any description on new plastered surfaces or concrete surface of any description over 10cm girth or width not other wise described over a coat of primer.complete all as specified and directed by Engineer-in-Charge. Make : BERGER (SILK,RANGOLI,EASY CLEAN)/ASIAN (ROYALE)/NEROLAC (IMPRESSION)/ECOCLAN/DULUX ICI

Demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness (below or above ground level) and Removing demolished material to a distance and depositing out site of MoD land Where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed by Engineer-in-Charge.

M&L Plain cement concrete type D2 1:4:8 (40mm graded aggregate), in foundation, filling and mass concrete, complete all as specified and directed.

Dismantling chain link fencing wiremesh, any type complete all as specified and as directed by the Engr-in-Charge.

Dismantling posts or struts (wooden, steel or RCC) any section embadded in concrete, brick work etc including taking out embedded portion.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50 metre and making good the disturbed grouind, in hard/dense soil, complete all as specified and directed by Engineer-in-Charge.

S&F angle iron with swain neck as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc, hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire all as specified and directed.

Supply only mild steel Galvanised wire chain link fencing square mesh of any size made out of any size wire complete all as specified & directed

S&F for mild steel bars 10mm dia and round bar over, to secure chain link fencing, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips conforming to Fe-410-W (Gde.E-250) Part- I quality-A or Fe 290 (Gde - E-165) complete all as specified and as directed.

Mild steel bolts machine made with hexagonal or square head one end each screwed other end to be fitted with washers and one hexagonal or square nut, n.exc 5 cm long and dia of neck 12 mm complete all as specified and as directed by Engineer-in-Charge.

Preparation of new or previously untreated steel or steel based surfaces of any description not otherwise described not exc 10 cm in width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide or zinc chrome primer complete all as specified and directed by Engineer-in-Charge. MAKE: NEROLAC PAINTS/ JEHNSON & NICHOLSON/BERGER PAINTS/ICI DULUXE/ASIAN PAINTS

S & F in repairs galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised MS wire staple or steel pins etc as directed (each line wire to be measured.) complete all as specified and directed.

Preparation of new or previously untreated steel or steel based surfaces of any description not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide or zinc chrome primer complete all as specified and directed by Engineer-in-Charge. MAKE: NEROLAC PAINTS/ JEHNSON & NICHOLSON/BERGER PAINTS/ICI DULUXE/ASIAN PAINTS

Plain cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate), as in , in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, benching, kneelers, apex stones, bed plates, kerbs not provided , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and directed.

TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engineer-in-charge.

TMT mild steel bars, 5 to 10mm dia, as in stirrups, spacers and binders for reinforcemnent, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) , complete all as specified and as directed by Engineer-in-charge.

Demolition cement concrete (unreinforced) of any descriptions and in any position not otherwise specificaaly provided for and removing demolished material to a distance and depositing out site of MoD land where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed by Engineer-in-Charge.

M & L PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in surface chanels and drain, complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc (inner girth only measured) all as specified and as directed.

S & F for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled forfixing of steel sheeting or other covering. doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete and conforming to Fe 410-W Gde E-250 quality 'A', including dismantling structrual steel work including doors and gates of any description complete all as specified and as directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 20mm thick granite of black shade (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Dismantling plain or corrugated steel sheeting any guage thickness including nanital or similar pattern complete all as specified and as directed

S&F 2mm Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with L type J type hooks or cranked bolts and washer in roof, wall etc complete all as specified and directed.

Strutural tubular steel as in stairs (framed) including stringers, treades, landing, balusters, hand rails etc. including cleats, brackets, etc. conforming to Fe 410-W (Gde-E- 250) quality including dismantling structure steel work any description and any position A complete all as specified and as directed by Engineer-in-Charge. Make and Procurement: All as specified in PS clause No 8 of tender documents

M&L for 2nd class soft wood clean sawn as in scantling fixed with nails, framed and fixed including dismantling timber scantling 40 sqcm and over in section, in any position as in framed work complete all as specified and directed.complete all as specified and directed.

Prepainted colored plained Galvalume/Zinc coated steel sheet with min 0.50mm TCT confirming to IS-513 (AZ-150 GSM, AL Zn alloy mettalic coating 550 MPA yield stress as per AS-1397), as in roof covering/cladding to wall fixed with self tapping screws colour/exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron top coat applied over 5 micron primer and a 5 micron polyster back coat applied over 5 micron primer, all fixed with Galvanised self drilling/self-tapping fastener (12-14 x 55 with EPDM seals) complete all as specified and directed by Engr-in-Charge Make : Tata Blue Scope Steel Ltd/JSW Steel Ltd/CRIL

M/S LEO TRADERS

M/S BALI CONSTRUCTIONS

PARIDHI CONSTRUCTION

Mehar Enterprises

SONAM ANGCHOK

M/S GLOBAL ENGINEERS