Special repairs to Bldg No. P 19 AND P-21 (OR Md Accn) of 11 Dogra at Solan Mil Stn under GE Kasauli

Amount

Demolition of cement concrete (un- reinforced) in ground floor and paving n. exc 15 cm thick below or above ground level complete all as specified.

Demolition of brick work or stone boulder masonry built in cement mortar complete all as spd and as directed.

Dismantling of RCC shelf other than ground floors and similar suspended works complete all as specified.

Taking down cement plaster of any description on brick wall surfaces etc including raking out joints, hacking for key , scrubbing down with water etc complete all as specified .

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified.

Brick work with sub class 'B' bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg/Sqcm) old size bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6, complete all as specified & directed.

Brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick built in CM 1:4 with sub class 'B' bricks of class designation 10 (minimum compressive strength of brick 100 kg/Sqcm) complete all as specified & directed.

Rendering 10mm thick on stone masonry surfaces or surfaces other than fair face of brick work in CM 1:6, finishing surfaces even and smooth without using extra cement complete all as specified.

5mm thick rendering in CM 1:3 on concrete surface of chajjas or ceiling, finished even and smooth without using extra cement complete all as specified and directed.

Rendering 15mm thick CM 1:4 on fair face of brick over concrete surface finished even and smooth witout using extra cement complete all as specified and directed. (WPC Shall be measured separately).

Non Skid /matt finished ceramic tiles (coloured) 600x600x 7 to 8mm thick (square/rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.38 sqm as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:6) complete all as specified and directed.

Non Skid ceramic tiles (coloured) 400x400x 7 to 8mm thick (square/rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:6) complete all as specified and directed.

Non Skid ceramic tiles (coloured) 400x400x 7 to 8mm thick (square/rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm but as on vertical surfaces set and jointed in cement slurry and pointed in coloured cement incl 10mm thick rendering in CM 1:4 complete all as specified and directed.

1st quality, glazed ceramic coloured tiles 350x250x 7mm/450x350x 7mm thick on vertical surface of walls with neat cement slurry @ 3.00 Kg / Sqm incl pointed in white cement with pigment to match the shade of tiles, over and incl screed bed 10mm thick 1:4 all as specified and directed.

Green marble flooring or on cooking platform 18 to 20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing fixed over and including 15mm thick cement screed bed in CM(1:6) and pointing in white cement (1:2) complete all as specified. ( size of the slabs shall not be less than 100cmx60cm ) Note:- (i) The rate of stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and polishing to achive the desired finish all as specified and directed.

RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in shelves / slabs and like with and incl use and waste of necessary form work complete all as specified.

Mild Steel TMT Bars 10mm dia and over cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Mild Steel TMT Bars 8 mm dia cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Cement concrete type B1 (1:2:4) using 20mm graded stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as specified

Taking down chawkhat or frame with shutters exc 1.50 sqm but n. exc 4 sqm (without taking off shutters from the frames) complete all as specified.

Taking down chawkhat or frame with shutters not exc 1.50 sqm (without taking off shutters from the frames) complete all as specified.

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm from chowkhat and removing to or from store as required complete all as specified.

Taking down shutters of any description exc 1 sqm but n.exc 2 sqm from chowkhat and re-fixing in same opening after re-securing or easening and adjusting including repair of hinge as required complete all as specified.

Plain solid straight chawkhats of 2nd class hard wood and frames rebate on the solid rounded or chamfered , put together with glue pinned at joints complete all as specifided.

Pressed steel frames for doors of size 125 x 60 mm with one or more rebates incl necessary fixing lugs, hinges, lock, strike plates of 50 x 3mm welded with frame for making arrangement for fixing of door spring etc. complete all as specified.

Pressed steel frames for doors of size 105 x 60 mm with one or more rebates incl necessary fixing lugs, hinges, lock, strike plates etc. complete all as specified.

Fixed factory made plain framed panelled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat on both sides feather edges or panel of 9mm BWP commercial ply over 12mm thick veneered particle board with commercial face veneers fixed to chowkhat . The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure treated complete all as specified.

2nd class hard wood 25mm thick made glazed and skeleton shutters factory made open rebated and prepared to receieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) complete all as specified.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail . Paneling of plain colour PVC sheets to be filted in MS frame welded, sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with the solvent cement complete all as specified.

Solid PVC door frame of size 50mm x 47mm made out 5mm plain colour PVC sheets re-inforced with MS square tube supplying and fixing in opening asper specification and drawing complete all as specified.

25mm flush shutters, solid core construction, with block board core and plywood face panels, commercial types on both sides incl teak wood beading alround the shutters as directed by Engr-in-Charge and all as specified.

Block board Grade 1 quality exterior grade, decorative type with decorative face veneer type on one face, including fixed in repairs 19mm thick, fixed with screws to timber frame incl wooden bracket as in cupboard shelves complete all as specified.

Factory made steel windows with side hung shutters including box type hinges with steel handle, tower bolt and steel peg stay with glazing bars complete all as specified.

Factory made steel windows with side hung shutters including box type hinges with steel handle, tower bolt and steel peg stay without glazing bars complete all as specified.

Factory made steel window or ventilator, fixed type, with glazing bars complete all as specified.

Mild steel framed work as in grills,guard bars etc. with ends of bars shouldered/welded and/or riveted and other simillar works confirming to Fe410-0 or Fe310-0 complete all as specified and directed.

Galvanized mild steel wire cloth 0.56mm fixed nominal dia of wire and avg width of aperature 1.18mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

3mm thick Sheet glass, ordinary quality and glazing with oil putty or secured with wooden beads as required in square n exc 0.5 sqm in each pane complete all as specified and directed.

3mm thick figured glass, pin head type quality and glazing with oil putty or secured with wooden beads as required in square n exc 0.5 sqm in each pane complete all as specified and directed.

75mm thick plain cement concrete 1:3:6 type C2 using 40mm graded stone aggregate, laid in 1:20 slope as in plinth protection, coping, surface finished even and smooth without using extra cement, with and incl use and waste of necessary form work complete all as specified and directed.

Mild steel butt hinges medium weight , cold rolled, 100mm, ISI marked, complete all as specified and directed.

Mild steel butt hinges medium weight , cold rolled, 50mm, ISI marked, complete all as specified and directed.

Mild steel butt hinges medium weight , cold rolled, 75mm, ISI marked, complete all as specified and directed.

Small fittings such as brackets of any type, latch and hinge blocks, door stops and window stops, the like incl all necessary labours articles n. exc 200 cucm each made up of 2nd class hard wood (hollock) complete all as specified and directed.

Barrel tower bolts aluminium anodised extruded section of size 200 mm complete all as specified and directed.

300 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections not less than 12mm dia with and including a minimum of 6 bolt and nuts ,fixed on plate or staple plate complete all as specified and directed.

Aluminium fabricated type extruded handles of size 125 mm complete all as specified and directed.

150mm size Hasp and staple MS wire type, stove enamelled black, incl bolt to hinge plate complete all as specified.

300mm mild steel ordinary rat tail rod pattern door spring incl roller and roller plate fixed in repair complete all as specified and directed.

20mm dia mild steel chromium plated curtain rails fixed with brackets, stops, rollers, etc. fixed in repair complete all as specified.

Taking up or down 15 mm dia steel tubing incl connection and removal from site complete all as specified.

Taking up or down 20 mm dia steel tubing incl connection and removal from site complete all as specified.

15mm bore size GI tubing medium grade with all fittings fixed to walls or laid in floors 15mm bore complete all as specified.

20mm bore size GI tubing medium grade with all fittings fixed to walls or laid in floors 20mm bore complete all as specified.

Steel tubing and connections cleaning for refixing and refixing old steel tubing and connections in new or in old position (walls ceiling floor etc) of 15mm bore of pipe complete all as specified

Steel tubing and connections cleaning for refixing and refixing old steel tubing and connections in new or in old position (walls ceiling floor etc)of 20mm bore of pipe complete all as specified

Cutting chase, pining in making good to facings where required & pointing in cement mortar 1:3 to ends etc or edges of landings, steps cills,sunshades, shelves,lintels,etc and cutting chases for concealed water tubing and making good,cutting n.exc. 10cm girth in brick walls all as directed.

15mm bib tap cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed in repair complete all as specified.

Stop valve/Angle cock fancy type cast copper alloy 15mm bore screwed down high pressure chromium plated concealed type fixed in repair complete all as specified and directed.

Stop valve cast copper alloy 20mm bore screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union fixed complete all as specified and directed.

PVC connections 15mm size with PTMT nuts of length 450mm fixed in repair complete all as specified and directed.

Dismantling water tanks exc 250 n. exc 500 ltr capacity complete all as specified.

500 ltr capacity rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed by Engineer-in-Charge

20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipes etc, complete all as specified.

Sinks with drainage board made of stainless steel 1mm thick, kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including brackets and connecting union to pipe overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm fixed in repair complete all as specified.

Viterious china squatting span ORISSA Pattern size 580x440 mm with integral foot rests, (excl flushing cistern and flush pipe) but with and incl connection to trap, and to flushing pipe anti-syphonage pipe, etc. complete incl provn of lime concrete and making good to floor, in repair complete all as specified and directed.

10 Ltrs capacity PVC cistern, syphonic action type, ISI marked, white at low level complete with PVC bends, flush pipe and making all connections with and incl inlets ball valve float, handle, brackets and making good the disturbed sufaces in CM 1:3 to match with the existing surface, in repair complete all as specified.

Vitreous china wash hand basin white flat back or angle back type size 600mm x 480 mm white incl Chromium plated pillar taps 15mm bore waste chain & plug , waste pipe and prop stopper but incl cutting for and pinning in ends of brackets or erecting stand fixed, in repair complete all as specified.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets, bracket guard and railing 60cm long incl screws, in repair complete all as specified.

Chromium plated shower rose heavy duty with swivel joints 125 mm dia fixed to 15mm GI pipe fixed in repair complete all as specified.

Chromium plated Soap dish of size 160x160x90mm any type fixed to plugs with chromium plated brass screws fixed in repair complete all as specified.

Brass chromium plated tubular towel rail 20mm dia 'D' type 60 cm long between flanges fixed in repair complete all as specified.

PCC (1:3:6) type C2 using 40mm graded stone agg as in surface channel / drains complete all as specified.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds/stopped ends etc. complete all as specified.

Mild Steel works as in bands, straps, hold fasts etc, conforming to Fe-290 , embedded portion duly painted with bituminious paint and sanded, complete all as specified.

Providing cement concrete C 1 (1:3:6) using 20mm graded stone aggregate as in filling of chowkats incl weathering, slightly rounded or chamfered angles and throating as directed incl necessary form work complete all as specified.

Dismantling of Cast Iron pipe 75mm to 100mm dia complete all as specified.

110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

75mm dia PVC (SWR) bends with oval accessed door with rubber ring joints fixed as required complete all as specified.

110mm dia PVC (SWR) bends with oval accessed door with rubber ring joints fixed as required complete all as specified.

75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement incl necessary PCC & form work as required complete all as specified.

75mm dia PVC (SWR) junction double, (double T), equal or un equal with oval accessed door including jointing with solvent cement as required complete all as specified.

110mm dia PVC (SWR) junction double, (single T), equal or un equal with oval accessed door including jointing with solvent cement as required complete all as specified.

110mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvent cement as required complete all as specified.

75mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvent cement as required complete all as specified.

110mm dia PVC (SWR) reducer, single, equal or un equal of any length including jointing with solvent cement as required complete all as specified.

75mm dia PVC (SWR) vent cowl, single, equal or un equal of any length including jointing with solvent cement as required complete all as specified.

110mm dia PVC (SWR) "P" trap single, equal or un equal of any length including jointing with solvent cement as required complete all as specified.

75mm dia PVC (SWR) bends with rubber ring joints fixed as required complete all as specified.

110mm dia PVC (SWR) bends with rubber ring joints fixed as required complete all as specified.

Preparation of new or previously untreated surface of wood or board materials of any description not otherwise described over 10cm in or girth & appyling two coats of synthetic enamal paint over a coat of pink primer complete all as specified.

Preparation of old wooden surface of any descreption not otherwise described over 10 cm widtn or gith & appling two coats of synthetic enamel paint complete all as specified and directed.

Preparation of new steel surfaces including preparation of surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Complete removal of existing old surfaces applying two coats of oil bound distemper over one coat of white cement based wall care putty on walls all as specified and directed by the Engr-in-Charge

Preparation of old decorated plastered / unplastered surfaces of ceiling applying two coats of white wash on ceiling and AC plain building board surfaces as in ceiling complete all as specified and directed by Engr-in-Charge

Two coats of distemper oil emulsion on wall incl preparation of new surfaces over one coat of primer on wall surface complete all as specified & directed.

Preparation of old external surfaces of wall & applying two coats of cement based paint complete all as specified.

Preparation of new external surfaces of wall & applying two coats of cement based paint over chalk whiting complete all as specified..

Preparation of old painted NTP/CGI/PGI or other steel roof surfaces, eaves and gutters etc exc 10 cm width or girth and applying one coat of roof paint of any tint as approved complete all as specified

Preparation of asbestos cement or plastered old painted surfaces of ceiling and applying One coat of synthetic enamel paint of approved tint complete all as specified

Stainless steel plate rack of size 900mm x 750mm with shelves, hooks and railing to keep plates vertically and horizontly, including necessary fixing arrangement complete all as specified.

Water proofing treatment of sunken floor of WCs, Bathroom etc. by applying of the following specifications:- (i) Cleaning of sunken floor surface with mechanical means i.e. wire brush/air blower etc.and remove all loose/unsound material,dirt,dust,etc. (ii) Applying cement slurry mixed with acrylic based polymer modified cementitious composite compound coating Hydroproof Xtra of FOSROC/Equivalent of Dr Fixit of pidilite industries Ltd in the ration of 1:2:4(One part of acrylic polymer : Two part of water and four part of cement). (iii) First layer of cement slurry @ 0.444 Kg/Sqm mixed with acrylic based modified cementitious composite compound @ 0.222 Litre/Sqm and allow it to air dry for 04 Hours. (iv) Second layer of cement slurry @ 0.222 Kg/Sqm mixed with acrylic based modified cementitious composite compound @ 0.111 Litre/Sqm and allow it to air dry for 04 Hours followd with water curing for 48 hours. (v) 200 micron thick polythene film shall be pasted with help of adhesives over treatment. Note:- Joints of WC/Trap/Soil waste shall be properly sealed with sealing compond.Testing of all traps and joint and sunken slab shall be done as per IS-1742 before filling and tiling work.

Dismantling plain or corrugated steel sheeting any gauge thickness incl Nainital pattern as in roof covering complete all as specified.

0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screws, in roofs, walls etc. with grade of zinc coating 275 complete all as specified & as directed.

0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified & as directed.

Preparation of newly plastered wall surface with 3mm thick white cement based wall care putty on wall surface,complete all as specified & as directed.

Non Skid /matt finished ceramic tiles (coloured) 600x600x 7 to 8mm thick (square/rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.38 sqm as on vertical surfaces set and jointed in cement slurry and pointed in coloured cement including provision of 10mm thick rendering in CM 1:4 complete all as specified and directed.

75mm thick cement concrete type D-2 1:4:8 using 40mm graded aggregate , as in filling of mass concrete for floors fixed in repairs complete all as specified.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc Laid, bedded and pointed in any mortar complete all as specified.

Machine cut kota stone slab 20-25mm thick in riser steps,skirting,dado , nosing and pillar over 10mm thick cement screed base laid with CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing,etc complete all as specified. Note:- (i) The rate of kota stone shall be deemed to incl for full rounded off corner/ edges/nosing incl holes for pipe all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and kota polishing to achive the desired finish all as spfd.

Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 15 mm thick screed bed or bedding with CM 1:6 ,etc complete all as specified. Note:- (i) The rate of kota stone shall be deemed to incl for full rounded off corner/ edges incl holes for pipe all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and kota polishing to achive the desired finish all as spfd.

Dismantling timber scantlings in any position in fillets, rails, posts, rafters , purlins, etc. under 40 sq. cm in section (Unframed work) complete all as specified .

Plain fillets, square, rectangular or triangular in section, and secured with nails or brads, using IInd class hard-wood clean sawn in sectional area exc 13 sq.cm and not exc 25 sq.cm fixed in repair complete all as specified.

Continuous piano hinges mild steel bright finish width of flap 30mm fixed in repair incl taking out the existing complete all as specified & directed.

Stone walling of random rubble, well bonded, bedded and solidly hearted, brought upto courses built in CM (1:6) complete all as specified.

-do- item No.117 here-in-before but except stone complete all as specified.

30mm flush shutters, solid core construction, with block board core and plywood face panels, commercial types on both sides incl teak wood beading alround the shutters as directed by Engr-in-Charge and all as specified.

Prelaminated particle board 19mm thick, exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination , fixed as in repair with screws to timber frame complete all as specified and directed.

Supply only water proofing compouond all as specified as per manufacturer's instruction

Precast cement concrete tiles polish finish in grade M-50 compressive strength 688 Kg/Sqcm as per IS-1237-1980 coloured i.e tera cota, Misty beige, smoke grey and design piazza size of tiles 360x270mm or crossword size 300x300mm and thickness of tiles 22mm+/-2mm over and including 15 mm thick screed bed in cement mortar 1:6 and jointed in cement slurry @ 3 Kg / sq metre and pointed in white or coloured cement to match the shade of tiles complete all as specified & directed.

Concealed stop cock fancy type cast copper alloy 15mm bore screwed down high pressure with fancy type, chromium plated with long shank and cup concealed type fixed in repair complete all as specified & directed.

Taking down carefully any type of battens or conduit point wiring with or except conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, pendent light fittings, MCBs / isolators, fan regulators, tube light fittings etc removing material from site and making good disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as directed by Engineer - in - Charge.

Point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi stranded, FRLS- FLEXIBLE WIRING CABLE CONFORMING TO IS: 694-1990 PVC insulated, unsheathed copper conductor cable in and including PVC concealed conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories / fittings, brass screws, washers etc, sunk zinc coated pressed steel terminal boxes including all cutting holes in or through walls, making good to walls, ceiling etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded copper conductor cable, unsheathed and connected to common earth and earth dolly complete all as specified and directed for the followings :-

One Tube light/bulb/fancy/bell/ Bldg security light point controlled by one, one way switch 05 / 06 Amps.

One Exhaust fan point controlled by one, one way switch 05 / 06 Amps.

One 3 pin, 05 / 06 Amps socket outlet point on independent board controlled by one, one way 05 / 06 Amps switch.

One 3 pin, 05 / 06 Amps socket outlet point on same board controlled by one, one way 05 / 06 Amps switch.

All as per serial item No 125.3 here - in - before but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15 / 16 Amps socket outlet point on independent board.

Switch piano flush type, 05 / 06 Amps single pole, one way 240 volts complete all as specified & directed.

Socket outlet 3 pin, 05 / 06 Amps flush type 240 volts complete all as specified & directed.

Switch piano flush type, 15 / 16 Amps single pole, one way 240 volts complete all as specified & directed.

Socket outlet 3 pin 15 / 16 Amps (2 in 1 Multipurpose) 240 volts complete all as specified & directed.

Lamp holder (Angular / Straight), insulated body, with back plate for batten fitting all as specified and directed.

LED lamp 9/10 watts all as specified and directed. Make :- C & S Cat no. LTHPLEDLAMP9W/B22 or equivalent in Bajaj/CG/Havells.

Aluminium housing LED 22 Watt inverter batten with inbuilt Li ion battery for power back up of 2 to 3 hrs complete all as specified and directed.

LED bulk head fitting 1 x 10 Watt attractive surface mounted type, with sheet steel housing with opal acrylic difuser and decorative and plates, plastic housing wire and ballast, suitable for mirror fittings, lamp holders ,connector blocks incl LED 10 watt etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size copper wire complete all as specified & directed.Cat part No CG 80IB10WLED , or C & S or equivalent in Philips/Bajaj/Havells.

LED building security light 30 watt LED inverter RTC inbuilt for AUTO ON/OFF and must have dimming facility from 10 to 100 % of rated wattage as per user defined timeline made pressure die cast housing with individuals LEDs and lens with modular secondary optics and IP 65 protection with electronics driver and copper conductor 3 core of 0.7 sqmm from ceiling rose to security light with bracket made out of GI light grade pipe of 32 mm dia , 1.5 metre long bend to an angle of 120 degree with fixing arrangements on wall fixed in repair complete all as specified and directed. Make: Halonix Cat no. HLSLD-ML04-30-CWL-INV-RTC-DIMM, Wipro or Philips

Fresh air fan PVC body 250 mm sweep with louvers duly mounted fixed properly in existing window/ventilator including all fixing /finishing materials and connected B/R works i.e. wooden/Ply/Aluminium items for fixing the fan complete all as specified and directed.

Ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified & directed by Engineer -in- Charge.

Taking down carefully unserviceable Sub main wiring of any size and type, removing material from for taking credit and making good the disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as directed by Engineer - in - Charge.

Sub main wiring with 06 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor FRLS- FLEXIBLE WIRING CABLE CONFORMING TO IS: 694-1990 with and including continuous earth wire of size 4 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all MS conduit accessories / fittings, brass screws, washers etc and connected to common earth dolly including all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as specified & directed. Note:-One meter of conduit along with 2x6 sq mm wire and one 4 sq mm earth shall be measured as one unit length.

Taking down carefully unserviceable distribution board of any capacity including wooden board and making good the disturbed surfaces of walls, etc including two coats of white / colour washing / distempering etc to match the existing complete all as directed by Engineer - in - Charge.

Sheet metal enclosure for DB's with IP 43 protection 200 Amp rated insulated bus bar, shrouded neutral bar, earth bar, blanking plate, cable ties & circuit identification labels 240 volt SPN 8 way concealed in wall including all cutting holes in or through walls, making good to walls, ceiling etc including two coats of white / coloured washing / distempering etc to the disturbed surfaces to match the existing with metal door complete all as specified and directed.Make- Legrand Cat No.607711 or Equivalent in ABB / HAGGER (L&T)

Vertical type IP-43-IK09 protection metal door DB 200 Amps rated copper bus bar, pan assembly etc with interlocking links, blanking plates cable ties identification labels TPN 4 way , DPX 125+ 12 modules with provision to mount DPX 100 A MCCB 4 Pole as incomer and SP/TP MCB as outgoing Make - Legrand Cat Part No 607790 or equivalent in Hagar/Schneider/C & S.

MCB SP, AC, 240 volts of 06 to 40 Amps, C curve, 10 kA, confirms to IS/IEC 60898 -1:2002 and making connections complete all as specified & directed.

MCB SPN, AC, 240 volts of 40 Amps, C curve, 10 kA, confirms to IS/IEC 60898 -1:2002 and making connections complete all as specified & directed. .

MCCB 4 Pole 100 Amps 16 KA, 415 volts , 50 Hz type DPX Frame size 125 with adjustable thermal & magnetic release all as specified and directed

Earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level ,steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to centre both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , for pit cover including testing on completion complete all as specified and directed. Note:-After completion of work if desired test result is not obtained the earthing is to be redone without any extra cost to deptt.

Taking out old unsv LT cable any size and Supply, laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 25 Sqmm 3.5 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches, fixing on wall, under road crossing through protection pipe etc. all as specified.

Supply, laying and fixing 40mm bore galvanised steel tubes with all fittings, light grade, laid in trenches for cable protection complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m depth in soft / loose soil and getting out in soft / loose soil complete all as specified.

Washed river dry sand cushioning in trenches 80mm thick before laying the cable and 150mm thick after laying the cable including spreading levelling and hard punning complete all as specified & directed by Engr-in-Charge.

Continuous brick edging with width equal to the depth of the brick of whole sub class 'B' bricks laid on edge complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n. exc. 25cm thick in soft / loose soil complete all as specified and directed.

Removing surplus excavated materials n.exc. 50 mtr and depositing where directed at a level n. exc. 1.5 mtr above the starting point complete all as specified.

Arsh Builder

RAJESH BUILDERS

M/s Parmod Kumar

Rajesh Agencies

R B TRADERS