CA NO GE/GUR-/NIT-10/2020-21 PROVISION OF POLE MOUNTED FLOOD LIGHT AT VOLLEYBALL, BASKETBALL AND BADMINTON COURT, SPECIAL REPAIRS TO CI/GI PIPELINES IN NEW WAPITI ENCLAVE AND SPECIAL REPAIR OF BLDG NO P-134 AT AFSSR GURGAON, PROVISION OF MISC WORKS

Amount

B/R WORKS Dismantling of stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors, aprons etc. complete all as specified and as directed.

Dismantling of brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level), including removal of rubbish outside MoD land, complete all as specified and as directed.

Taking down cement plaster on brick walls & concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, including removal of rubbish outside MoD land, complete all as specified and as directed

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the permises complete all as specified and as directed

Excavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation etc for shaft wells cess pits manholes, pier holes not exc 10 Sqm on plan in any type of soil and getting out complete all as specified and as directed

M&L for plain cement concrete 1:4:8 type D-2, with using 40 mm grades stone aggregates as in foundations and mass concrete etc complete all as specified and as directed

M&L for brick work with sub class 'B' brick, straight or curved on plan exc 6.0 mtr mean radius built in CM 1:6 etc complete all as specified and as directed

Ditto all as per item No. 8 described here in before but except bricks (old bricks shall be obtained from item No. 2 above)

M&L ATT for treating the bottom and sides of excavation at the rate of 5 Ltrs of emulsion per sqr mtr of surface area complete all as specified and as directed

M&L ATT for treating the back fill in contract with foundation at the rate of 7.5 Ltrs of emulsion per Sqm of vertical surface (area of the sub structure in contact with back fill to be measured ) etc complete all as specified and as directed

M&L ATT for treating the top surface of filled up earth at the rate of 5 Ltrs of emulsion per square meter of surface complete all as specified and as directed

M&L for 40mm thick damp proof course to horizontal or vertical surfaces in cement concrete (1:2:4), type B-0 (using 12.5mm graded crushed stone aggregates) including necessary formwork complete all as specified and as directed

M&L for rendering 10 mm thick in CM (1:3) on fair faces of concrete ceiling surfaces finsihed even and smooth (without using extra cement) etc complete all as specified and as directed

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finished even and fair mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

M&L for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) etc complete all as specified and as directed

M&L for rendering 15 mm thick in CM (1:6) on other than fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) etc complete all as specified and as directed

Supply only WPC

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc complete all as specified and as directed

M&L for TMT bars 5 mm dia and over, upto and including 10 mm dia as in stirrups, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and as directed

M&L for formwork to sides and soffits of floor or roof beam, beam and haunching, girders, bressummers, lintels cantilevers, shelves including supports, overhangs etc also splays between floor and beam etc complete all as specified and as directed

M&L for providing reinforced cement concrete (1:1.5:3) (M-20) Nominal Mix with using 20 mm graded stone aggregates as in beam, cantilevers, bressumers, lintels over 1.5 mtr span etc complete all as specified and as directed

M&L for formwork to sides chullah hoods, chajja, trough and similar items including edges etc complete all as specified and as directed

M&L for providing reinforced cement concrete(1:1.5:3) (M-20) Nominal Mix with using 20 mm graded stone aggregates as in chajja etc complete all as specified and as directed

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed

Material and labour for preparation of old painted surfaces of steel of any description and girth, not otherwise described and treated with one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of new or previously untreated wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Material and labour for preparation of old painted surfaces of wood and wood based of any description and girth, not otherwise described and treated with one coat of synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of 2mm thick wall care putty on wall to achieve uniform and smooth surface by roller brush having no sign of brush marks complete all as specified and as directed.

M&L for preparation of old surfaces of walls including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc.; rubbing down and stopping of surfaces using sand paper and applying one coat of oil bound distemper, complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of 2mm thick wall care putty on wall to achieve uniform and smooth surface by roller brush having no sign of brush marks complete all as specified and as directed.

M&L for preparation of old surfaces of ceiling including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc.; rubbing down and stopping of surfaces using sand paper and applying one coat of oil bound distemper, complete all as specified and as directed.

Material and labour for preparation of old decorated surface of walls and applying one coat of weather proof exterior emulsion (colour matching with existing) paint by roller brush of approved manufacturer complete all as per manufactures instruction and as directed.

Material and labour for preparation of newly plastered surface of walls and applying two coats of weather proof exterior emulsion (colour matching with existing) paint over a coat of alkaliresistant priming paint by roller brush of approved manufacturer complete all as per manufactures instruction and as directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed

M&L for screed bed or bedding layer of mortar 20mm thick in CM 1:6 for laying floor finishes complete all as specified and as directed.

M&L for machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L for Rendering 12mm thick in CM (1:4) on fair faces of brick work or concrete surfaces as backing coat of skirting etc complete all as specified and as directed

M&L for framed work as in grills, grating etc with ends of bars shouldered and / or riveted or forged into spikes framed guard bars barred iron doors, ladders framed baluusters wals ways, railing framed wor of water tans and similar work etc complete all as specified and as directed

S&F 35mm thick flush shutter solid core construction with block board core and ply wood face panels, commercial type on both sides complete all as specified and as directed

S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed

S&F aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed

S&F 100 mm thick butt hinges, heavy weight, cold rolled mild steel and fixed etc complete all as specified and as directed

S&F 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed

S&F window section of frame 72x55 mm fixed to wall or concrete surface with rowl plugs made, of galvanized steel powder coated and section of shutter 47x20 mm ,mulion section 72x50 mm (Base steel as per IS 513 "D" quality galvanozed as per IS 277 with zinc of 120 gms/sqm.) glazed or gauged and wire gauge shutter prepare to receive wire mesh to the shutter(Double door shutter) with total coated thickness of 0.6 mm including grills/guard bars made of square bars powder coated fixed to windows frame with screws at 150mm c/c both ways, 4 to 5 mm thick sheet glass, 0.36mm stainless steel wire cloth with 1.40mm aperture necessory fittings and all builders hardware such as handles, tower bolts & stays etc. complete all as specified and as directed Make:- NCL type-4000 series.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and as directed

Removing excavated soil to a distance exc 250 mtr but not exceeding 500 mtr and depositing where directed etc complete all as specified and as directed

M&L for PCC (1:2:4), type B-0 (using 12.5mm graded crushed stone aggregate) 25mm thick as in floors finished even & rough to receive the bedding mortar, omplete all as specified and as directed

M&L for first quality, Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sq.m but not exceeding 0.11 Sq.m, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed in cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and as directed.

M&L for first quality, virified ceramic tiles (any shade) 10 mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid in floors set and jointed with neat cement slurry @ 3.00 kg/Square Metre over and including 15 mm thick screed bed in cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and as directed.

Ditto as per item Nos 50 above but on vertical surfaces such as skirting fixed on and including 10mm thick rendering in cement mortar (1:4) as backing coat complete all as specified and as directed.

M&L for first quality coloured glazed ceramic tiles, fixed in pattern of different colour including border of size 300x 450 x 7mm thick as in vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white cement with pigment to match with shade of tiles laid on and including 10 mm thick rendering in cement mortar (1:3), complete all as specified and as directed.. Note :- Pattern of the tiles shall be approved by GE at the time of execution.

M&L for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in coping, bed block, kneels, apex stones etc including weathering slightly rounded or chamfered including form work complete all as specified and as directed

M&L for 75 mm thick, plain cement concrete (1:3:6), type C-2, (using 40 mm graded mechanically crushed stone aggregates), laid in 1:20 slope as in plinth protection including making joints at 3.00 metre intervals and at each corner, the joint shall be filled with mastic filling (to full depth) comprising of one part heated hot blown bitumen 85/ 25 & two parts heated sand (by volume), surface finished even and smooth without using extra cement, complete all as specified and as directed. Note: The concrete shall be laid at a stretch not exceeding 3 metre in length and width of joint shall not be more than 12 mm.

S&F in repairs bib taps, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule ccomplete all as specified and as directed.

S&F in repairs Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for 15mm bore iron pipe complete all as specified and as directed.

S&F in repairs angle cock/stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15 mm bore iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repairs 15mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as specified and as directed.

S&F in repairs 20mm dia gun metal gate valve, with iron wheel head, screwed both ends for iron pipes complete all as specified and as directed.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S & F in repairs 10 litres capacity, PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and suitable flush pipe PVC 32mm dia complete all as specified and as directed.

Supply and fix Vitreous China wash down water closet (pedestal pattern), white with seat cover and bras jet spray, PVC connections complete, including connection to waste pipe, flushing pipe, anti-syphonage pipe etc. and making good to floor complete all as specified and as directed.

S&F towel rail 600 mm long, 20 mm dia, ‘D’ type, brass, chromium plated, fixed to walls with screws and plastic cleats, complete all as specified and as directed.

S&F in repairs vitreous china squating pan, 'Orissa' pattern, size 580x440mm white, with integral foot rests, including 100mm cast iron 'P' or 'S' trap and 100mm cast iron sanitary connection socket to fit WC outlet including connection to trap, to flushing pipe, anti-syphonage pipe etc. complete including making good to floor complete all as specified and as directed.

S&F in repairs Wash basins, vitreous china, white, flat back of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, 32mm dia HDPE waste pipe and including new brackets complete all as specified and as directed.

Taking up or down steel tubing and connections 15mm dia pipes including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down steel tubing and connections 20mm dia pipes including cleaning for refixing or removal to store complete all as specified and as directed.

S & F 15mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and as directed.. Note : Cutting chases as required shall be measured and paid seperately.

S & F 20mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and as directed.. Note : Cutting chases as required shall be measured and paid seperately.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, including removal of rubbish outside MoD land complete all as specified and as directed.

Cutting holes into or through brick/ concrete walls built, in cement mortar, exceeding 150 Sqcm but not exceeding 400 Sqcm in superficial area and making good in cement mortar (1:3) to match with the existing finishes, complete all as specified and as directed.

M&L for, 75mm dia cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, including cement jointing, laid in trenches or in floors including necessary excavation and earth work, complete all as specified and as directed.. Note : Extra over for lead joints shall be measured and paid separately.

M&L for, 100mm dia cast iron soil, waste and vent pipes (sand cast) in any length with or without ears, including cement jointing, laid in trenches or in floors including necessary excavation and earth work, complete all as specified and as directed.Note : Extra over for lead joints shall be measured and paid separately.

S & F cast iron bends 75mm bore, diminishing pieces or tapers fitted with oval access door ISI marked complete all as specified and as directed.

S & F cast iron bends 100mm bore, diminishing pieces or tapers fitted with oval access door ISI marked complete all as specified and as directed.

Materials and labour for extra over for lead joints provided in lieu of cement joints for 75 mm dia cast iron pipes and fittings, complete all as specified and as directed.

Materials and labour, extra over for lead joints provided in lieu of cement joints for 100mm dia cast iron pipes and fittings, complete all as specified and as directed.

S&F cast iron floor trap, 75 mm dia of out let, ISI marked, with CP grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1,complete all as specified and as directed.

S&F factory made PVC solid door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of 5 mm thick plain colour PVC sheet cut at corner and jointed with 02 Nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge (EPDM) rubber gasket weather seal provided throughout the frame and fixed to wall with 65/100 mm long mild steel screws through the frame by using PVC fasteners (minimum of 04 Nos. of screws to be provided for each vertical member & minimum 02 Nos. for horizontal member), complete all as specified and as directed.

S&F Factory made moulded door shutter with particle board core, 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick moulded prelam PVC sheet on the front face & 2 mm prelam PVC sheet on back face, complete all as per manufacturer instructions complete all as specified and as directed.

Hacking out old broken glass (any thickness size, quality or description) from wooden/ steel frames, glazed with putty or fixed with wooden beads/ metal pins complete all as specified and as directed.

S & F 3mm thick Sheet glass ordinary quality and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane, complete all as specified and as directed. Note:- New wooden required for glazing glass in wooden window shall be paid for separately.

S & F 3mm thick figured glass, pin headed type and glazing with oil putty or wooden bead in squares not exceeding 0.5 Sq. m in each pane, complete all as specified and as directed.

S & F MS 20 mm dia curtain rod, bright finish, including set of fixing brackets, fixed to wall in repairs, complete all as specified and as directed.

M&L for Cutting holes in brick walls exceeding half brick but not exceeding one brick built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or PCC 1:2:4, including removal of rubbish outside MoD land, complete all as specified and as directed.

S&F in repairs 32 mm bore and 75cm long PVC waste pipe for WHB complete all as specified and as directed.

S&F in repair grating 100mm dia with or wihout waste hole of brass chromium plated fixed on floor/nahani trap with coment mortrar complete all as specified and as directed.

Cleaning and removing all scales and dirt etc by scraping with hard plastic/nylon wire brush and washed with bleaching power solution and thereafter washed with clean water from service water tank and mouth of circulating pipe of capacity of tank exc 250 litre but not exc 500 litre including writing letters " Tank cleaned on _ (date) boldly with thick white/black synthetic enamel paint by using stencil with height & width of each letter & figures 150mm & 10mm respectively complete all as specified and as directed.

M&L for applying cement paste mixed with RBR compound (Roof Bond Repair) mixed in ratio as per instructions to stop the seepage, applied in sides of Nahni trap/floor traps, W.C traps, junction of CI pipes, bends & similar item junctions to eliminate the seepage.

S&F Toilet paper brass CP holder complete all as specified and as directed. Make: Model NL 55 make ESS ESS or equivalent in marc/ Jaquar/Prima.

S&F Acrylic shelf 46X13cm make ESS ESS model (TM 07) chrome or equivalent complete all as specified.

S&F for CP brass liquid soap container fixed with and incl CP brass screws.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confriming to IS 15658-2006 of 80 mm thickness , M-40 grade with Grey Cement and no pigment, laid over 20 mm thick sand cushion over 75mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate all as specified.(Sand cushion will be measured and paid seprately).

M&L for sand cushioning including watering and consolidations etc complete all as specified and as directed

M&L for exterior grade, coloured glossy finish rubber pressed, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thick ( as approved by GE) set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc laid over including 15 mm thick cement screed bed in CM 1:4 . complete all as specifed and as directed

M&L for 75 mm thick cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate in sub base all as specified & directed by Engr -in charge

M&L for providing cement concrete (1:3:6) type C2 (using 40 mm graded crushed stone aggregate) as in surface channels and drains complete all as specifed and as directed

M&L for Running welding in repairs thickness of metal to be welded exc 6mm but n.exc 9mm complete all as specifed and as directed

S&F Rotational moulded polyethylene water storage tank 500 litres capacity, ISI marked triple layer construction (cylindrical vertical closed top), hoisted & fixed in position including S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball, screwed for 20mm bore GI pipe of having weight not less than 210gms including all fittings and gate valves with iron wheel head 20mm size, including taking down existing tank complete all as specified and as directed.Make-SINTEX /POLYCON /Polywell.

S&F Door closer hydraulically regulated, universal type designation No 3 suitable for door shutters of 851 to 1000mm in sedth and weight between 61 to 80Kg complete all as specified and as directed.

S&F in repair mild steel sliding door bolts, 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S&F in repair brass handles, cast type, polished bright, 150mm in size complete all as specified and as directed.

Taking down Chowkhats with shutters (without taking of shutter from the frame) of any description not exceeding 1.50 Sq. m each, and making good the disturbed Surface in CM 1:4 & finished with similar specification as exists, complete all as specified and as directed

M&L for providing pre cast RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in cover slab man hole covers and drain covers with 40mm dia holes made in the slabs to drain runoff etc complete all as specified and directed by Engineer-In- Charge

M&L for providing concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) for 150mm bore dia of pipe complete all as specified and directed by Engineer-In- Charge

Cutting into existing manholes for connecting new drains, making good to 150mm bore dia pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed by Engineer-In- Charge

M&L for providing cement concrete (1:2:4) type B2 (using 40mm graded crushed stone aggregate) as in surface channels and drains complete all as specified and directed by Engineer-In- Charge

S&F bib taps, cast copper alloy, chromium plated, fancy type with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule ccomplete all as specified and as directed.

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for 15mm bore iron pipe complete all as specified and as directed.

S&F angle cock/stop valves, cast copper alloy, chromium plated, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for 15 mm bore iron pipe or for brass ferrule complete all as specified and as directed.

S & F 10 litres capacity, PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and suitable flush pipe PVC 32mm dia complete all as specified and as directed.

S&F Wash basins, vitreous china, white, flat back of size 550x400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, 32mm dia HDPE waste pipe and including new brackets complete all as specified and as directed.

S&F 50mm bore dia Cast iron cowls complete all as specified and as directed.

S&F 50mm bore dia cast iron soil, waste and vent pipes sand cast in any length with or without ears, with cement joints, fixed to wall complete all as specified and as directed.

M&L for RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) (nominal mix) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs exc 5cm but not exc. 10cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in Soft/loose soil complete all as specified and as directed.

Excavation in trenches in soft/loose soil n.exc 1.50 m wide and n.exc 1.50 m in depth for foundation or shafts, wells, cesspits, manholes, pier holes, cable laying, sewage/water lines etc complete and getting out all as specified and directed.

M&L for TMT bars 6 to 8 mm dia as in reinforcement for concrete, cut to length, bent to shape required including cranking , bending spiraly for hooping for columns, hooking with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips all as specified and as directed

M&L for reinforced cement concrete Type B1 1:2:4 (20 mm graded aggregate) (nominal mix) in foundations, including rafts, footings, foundation beams; beams; bases for columns, etc; basement slabs, under reamed piles and mass concrete all as specified and as directed

M&L for brick work with sub class "B" bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:4. finishing even and smooth without using extra cement complete all as specified and directed.

Removing of excavated material (soils) n.exc 50m and geposited where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Hardcore of gauge n exc. 63 mm, deposited , spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface using broken stone boulders complete all as specified and directed.

M&L for 150mm thick Cement concrete type D-2 , 1:4:8 (40 mm graded aggregate) as in sub base of floors complete all as specified and directed.

M&L for 150mm thick Cement concrete type B-1, 1:2:4 (20 mm graded aggregate) as in floor Finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Forming Contraction ( Dummy ) joints 65 mm deep x 10 mm wide, filled with sealing compound Grade 'B' complete all as specified and directed.

Forming construction joint 150 mm deep x 10 mm wide filled with sealing compound Grade 'B' complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate as in plinth protection Finishing fair and even complete all as specified and directed.

M&L for preparation of newely plastered surface of wall and applying two coat of cement base paint over a coat of primer etc complete all as specified and as directed.

S&F expended steel wire fabric with steel member weight exc 4 kg/sqm etc complete all as specified and directed.

Ditto all as per item No 121.00 described here-in-before but depth exc 1.5 mtr but not exc 3.0 mtr

S&F reinforced cement concrete drain pipes of 150 mm bore class NP-2, laid and jointed complete with collars etc complete all as specified and as directed.

E/M WORKS Supply and fixing LED floodlight with powder coated long life versatile pressure die-cast aluminium IP65 light luminaire 200W LED with high power LEDs as light source, complete with all accessories complete all as specified and as directed.

Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core complete all as specified and as directed.

Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete all as specified and as directed.

Supply and filling river sand in trenches including spreading for cushioning of LT UG cable complete all as specified and as directed . Note : Punned down thickness shall be measured and paid

M&L for sub class ‘B’ bricks old size laid flat dry in trenches over cable, across the direction of cable complete all as specified & directed .

M&L for Foundation for Tubular swaged type Pole including excavation , getting out, pole foundation with PCC type D2 1:4:8 (with 40 mm graded aggregate). Coping of pole with PCC type C1 1:3:6 ( with 20 mm graded agregate) and removing surplus soil to a distance n.exc 50 m and making good surface all as specified and directed.

Supply & install steel tubular pole of dia 50mm bore GI pipe (6.0 metres long) complete with CI base plate including welding of base palte and channel/socket reducer at top for fixing of flood light/Post top fitting and painting with aluminium paint of two coats complete all as specified and as directed .

Supply and fixing weather proof street light junction box of size 300 x 200 x 105mm including MCB SP 6 Amps and connecting terminals 4 way and fixing with street light poles using necessary MS clamps, nuts, bolts washers, lugs for incoming and out going cables, gland for cable etc of suitable size complete all as specified and as directed. Make : Hensel/Sintex/Universal Switch Gear control . Note : The rates quoted are inclusive of provision and fixing of suitable lugs and glands for cable connection.

Material and labour for wiring with PVC flat twin core sheathed of PVC insulated 4 sq mm aluminium conductor (and fixing brackets on PCC pole) from Loop-in-loop out junction box to light fitting terminal complete all as specified and as directed.

Supply and fixing LED post top light with powder coated long life versatile pressure die-cast aluminium IP65 light luminaire 20W LED with LEDs as light source, complete with all accessories.

Item No. 147.00 Contd...... (B) Outgoing (i) Supply and fix automatic timer switch with switches ON/OFF the street analog based current rating 20 Amps, 220 Volts, 50 Hz. The sensor based timer should also have over voltage and low voltage trip with auto reset facility the sensor alongwith suitable power contactor, MCB and support terminals should be enclosed in pole/wall mountable enclosure made of rust proof electric shock proof termite proof and FR grade special moulding compounds confirming to IP 54. The contactor MCB and circuit wiring shall have enough capacity to take load of 12 KW equally distrubuted over 3 phase complete all as specified and as directed - 01 No (ii) MCCB 40 Amps, 25 kA, 3 Pole, 415 Volts with thermal magnetic device with bus bar spreader links for connecting both incoming and outgoing cables with suitable connections with suitable size of glands etc complete including testing & commissioning all as specified and as directed by the Engineer-in-Charge- 03 Nos (iii) Spare space for mounting MCCB

Supply and fixing LED decorative post top light for 360 degree indirect light glare free and better uniformity with powder coated long life versatile pressure die-cast aluminium IP65 light luminaire 60W LED with LEDs as light source, complete with all accessories.

Taking up or down steel tubing and connections, including removal to store complete all as specified and as directed.

40 mm Bore dia

20 mm Bore dia

80 mm Bore dia

Supply and laying CI pipe line with spigot and socket ends and centrifugaly cast class "LA" in any length laid in trenches of size 80 mm bore complete all as specified and as directed.

Supply and laying GI pipe line with all fittings like socket of any type, elbow, bend, union, short piece, long screw, flange, cutting & welding as reqd site, medium grade laid in trenches of size:- Note : All fixing materials are included in the unit rate

40mm bore dia

20 mm Bore dia

Supply and fix in replacement cast iron flanged drilled heavy duty sluice valve of size 80 mm bore with ISI mark with stainless steel spindle and check nut and plan PN-1.6 complete with rubber insertion, nuts and bolts with washers etc including taking down old unserviceable sluice valve of size 80 from existing position after removing out nuts/bolts etc complete all as directed. Note :- Nuts, bolts and gasket is included in the unit rate

Supply and fix in repair Gun Metal globe or Gate valve iron wheel head screwed both ends for iron pipes of size 40mm dia bore complete all as specified and directed by Engr-in-Charge after taking down old one including M&L for construction of Valve pit chamber 60 cm x 60 cm (inner dimension) and 75 cm deep , from the top of MS cover fixed on PCC Base, top cover shall be of 3 mm thick MS Sheet with locking arrangement of pad lock of 50mm size including brick work with sub class "B' bricks i CM 1:4 including 15 mm thick plaster in CM 1:4 (internally and externally) and necessary earth work in any type of soil including returning filling in and disposal of surplus oil to a distance n exc 50 mtrs and 150mm thick PCC 1:4:8 type D-2, using 40mm graded stone aggregates as in floor complete all as speicified and directed. Note : All fixing materials like socket & threading is included in unit rate.

Ditto all as per Item No. 154.00 described here-in-before but of size 20mm bore

M&L for CI Bends (any type, radius and angle) tapers any type,(straight, bend,increasing,decreasing or double socket etc.) Tee pieces single branch. "Y" junction,double branch cross (all sockets or scocket and spigot) collars, Tail piece, caps and plugs upto 150 mm bore CI pipe.

M&L for construction of Valve pit chamber 90 cmx90cm (inner dimension) and 90 cm deep , from the top of MS cover fixed on PCC Base , top cover shall be of 3 mm thick MS Sheet with locking arrangement of pad lock of 50mm size including brick work with sub class"B" bricks in CM 1:4 including 15 mm thick plaster in CM 1:4 (internally and externally) and necessray earth work in anu type of soil including returning filling in and disposal of surplus oil to a distance n exc 50 mtrs and 150 mm thick PCC 1:4:8 , type D-2 , using 40mm graded stone aggregates as in floor complete all as specified and directed.

M&L for point wiring complete with stranded copper conductor 1.5 Sqmm size (Nominal area) PVC insulated unsheathed FRLS Grade cable 1100 volts grade confirming to IS: 694 for phase and neutral drawn in and including medium duty concealed PVC conduit confirming to ISI marked not less than 20mm dia with concealed sunk-in pressed steel terminal boxes of required size not less than 1.2 mm thick factory made and painted with stove enamelled black paint top cover 2.80 mm thick plastic laminated sheet of required colour fixed with brass screwes and cup washers including single core stranded copper conductor 1.5 Sqmm PVC insulated unsheathed cable as earth wire to common earth and connected to earth dolly drawn in same concealed conduit complete all as specified for the following :-

One light point controlled by one, one way switch with cables 1.5 Sqmm size all as specified and directed.

One Ceiling fan/Exhaust fan point controlled by one, one way switch with cables 1.5 Sqmm size all as specified and directed.

One 5 pin socket oulet 5/6 amps on same board including single core stranded copper conductor 1.5 sqmm PVC insulated and unsheathed cable drawn in same conduit as earth wire to the common earth and connecting to earth dolly all as specified.

One 5 pin socket oulet 5/6 amps on independent board including single core straned copper conductor 1.5 sqmm PVC insulated and unsheathed cable drawn in nsame conduit as earth wire to the common earth and connecting to earth dolly all as specified.

One bell/buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sqmm size all as specified and directed.

M&L for point wiring complete with stranded copper conductor 4 Sqmm size (Nominal area) PVC insulated unsheathed FRLS cable 1100 volts grade confirming to IS: 694 drawn in and including medium grade concealed PVC conduit confirming to ISI marked not less than 25mm dia with concealed sunk-in pressed steel terminal boxes of required size not less than 1.2 mm thick factory made and painted with stove enamelled black paint top cover 2.80 mm thick plastic laminated sheet of required colour fixed with brass screwes and cup washers including single core stranded copper conductor 4 Sqmm PVC insulated unsheathed cable as earth wire to common earth and connected to earth dolly drawn in same concealed conduit complete all as specified for one 6 pin socket outlet two in one 16/6 Amps on an independent board. (for geyser point) Note : For item No 158.00 to 160.00 : Rates are deemed to be included for chases of conduit and sunking for boxes cutting and making holes in wall/floor for passing in or through conduit. No Extra payment shall be done on this account

Ditto all as per Item No. 159.00 described here-in-before but with cable 2.5 Sqmm and earth continuity conductor of 2.5 Sqmm stranded copper unsheathed complete all as specified and as directed.

Supply and fix in repairs switch piano, flush type single pole, one way, 5 Amps, 240 volts, ISI marked complete all as specified and as directed.

Supply and fix in repairs switch socket combination 2 in 1, 3 pin 5 Amps, ISI marked complete all as specified and as directed.

Supply and fix in repairs switch socket combination 5 Amps/16 Amps, 5 in 1, flush type, ISI marked complete all as specified and as directed.

Supply and fix in repairs ceiling roses, 3 phase, PVC/Polycarbonate, isolated body complete all as specified and as directed.

Supply and fix in repairs stepped type electronic fan regulator flush type, ISI marked on the existing phenolic laminated sheet etc as required complete all as specified and as directed.

Supply and fix in repairs bell push flush type single pole, one way, 5 Amps, 240 volts ISI marked complete all as specified and as directed.

S&F submain wiring with unsheathed multi-stranded FRLS Grade copper conductor cable 1100 volts grade drawn through in and including PVC rigid conduit medium grade of not less than 25mm dia with conduit accessories and concealed in wall/surface of ceiling for two runs of 6 Sqmm single core HR Grade and one run of 6 Sqmm PVC insulated copper conductor for earth continuity wire between main DB to Sub main DB complete all as specified and as directed. Note :- (i) Two run of single core cable with one run of earth continuity conductor and PVC conduit and accessories will be measured as one length including (ii) Rates shall deemed to be included for chases of conduit and sunking for boxes cutting and making holes in wall/floor for passing in or through conduit.

Supply and fix of 20 watt (4ft long) decorative box type fitting with blue coloured end caps for LED tube etc complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable from ceiling rose to terminal block and testing complete all as specified and directed at site.

Supply and fix of 12 watt 2 ft decorative box type fitting with coloured end caps for LED tube etc complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable from ceiling rose to terminal block and testing complete all as specified and directed at site.

M&L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6mm thick burried directly in ground not less than 2.25m deep below normal ground level (with the top edge of the plate not less than 1.50 m below the normal ground level) connected to GI earth wire 4 mm by means of GI bolts, nuts, check nuts and washers of GI all as shown in electrical plate No.3 of SSR Part-I connected to earthing test point with and including necessary excavation and earth work in any strata PCC pit 1:3:6 type C-1, 20mm bore medium grade GI pipe for watering 15mm bore light grade pipe for GI wire protection and funnel including 40mm thick RCC slab cover and testing on completion all as specified and as directed.

Supply and fix of LED building light luminaire 30 watt, pressure die cast aluminium housing with heat resistant toughened glass & IP66 protection complete all as specified and as directed.

M&L for bracket made from GI pipe light grade 40mm bore bent to shape as required at site for street light fitting 1.2 mtr in length and fixed on wall/pole including necessary MS clamps, nuts, bolts and washers including welding and painting complete all as specified and as directed.

Supply and fix MCB, DB , SPN 8 way suitable for single phase 240 volts with 100 Amps rated bus bar, double door type suitable for mounting incoming and outgoing MCB's single/double pole complete all as specified and directed at site.

Supply and fixing of MCB signle pole 5-30 Amps 230 volts 'B' series complete all as specified and as directed.

Supply and fixing of MCB single pole and neutral 40 /63 Amps 230 volts 'B' series complete all as specified and as directed at site.

Supply & fix of SPN enclosure with two pin and earth plug and socket complete with on SP MCB 20 Amps complete all as specified and directed.

Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V all as specified and directed.

Supply and fixing air termination single pointed copper rod 12 mm 300 mm long complete all as per releavent IS specification all as specified and directed.

Supply & fix copper strip 20mm x 3.15mm complete with saddles and fixing screws for fitting the strip for roof conductors and down conductors above ground.

Supply & fix copper strip 32mm x 6 mm complete with saddles and fixing screws for fitting the strip for roof conductors and down conductors above ground.

Test point terminal block made of gun metal or phosphorus bronze size drilled and screwed including75x75x25mm 3 nos. 8mm dia 25mm long hex. head screw.

M&L for earthing complete with copper earth plate electrode 600 x 600 x 3.15mm size brazed copper earth plate buried directly in ground vertically in pit of size 120 cm x 120 cm depth not less than 5.30 metre below normal ground level (with the top edge of the earth plateat a depth not less than 4.70 m below the normal ground level) surrounded from all side wth mixture of one layer each of MGSO-4 of size 120X120X5 cm at bottom and 120X120X5cm at top in remaining portion 14 layers of charcoal (each layer of 0.23 cum) and 14 layyers of salt (each layer of 0.23 cum) in alternate layers and electrode connected to erth lead of copper earth strip of size 32X6mm by means of brass bolts, nuts, check nuts and washers, earth strip protected by Galvanised steel pipe 50mm bore (light grade) connected to electrical equipment and including necessry excavation and earth work in any type of soil, 50 mm bore medium grade GI pipe with holes of 1-2 cm dia on all sides at an interval of 15cm for watering, funnel with wire mess, PCC (1:3:6) type C-1 chamber, including Pt-1 complete all as specified and direcetd. Note: (a) The unit rate includes earth strip and protection pipe (Maximum 7.5 mtr from earth plate) Earth point/ test point. (b) Each type of earth is to be provided with a colour code and marking Earthing pits for Chemical EPs - Red and for conventional/ LA earth pit - Yellow and size of identifier/Marker - 30 cm x 20 cm board, height from ground- 2ft above the ground 1 inch pole (min) all as specified and directed by Engr-In-charge at site.

Item No. 182.00 Contd... (c) Chemical earth pit identifier/marker colour should be Black text with red background for Base plate cover of earth pit (text in black with red background) and for conventional earth pit black text with yellow background for marker and (text in black with yellow background) for earth pit.

M/S ujjwal associates

Ridhi engineers and builders

M/s GANJOO AND CO

akhil enterprises

G M CONSTRUCTION COMPANY