CA NO. GE AF NO.1/GUR-04/2024-25 IMPROVEMENT TO SMQs (P-139/1 TO P-139/6) AT AF STATION GURGAON UNDER GE (AF) GURGAON NO.1 .

Amount

Demolition of RCC of any description and in any position not other wise specially provided for complete all as specified and directed by Engineer in Charge .

M&L for RCC nominal mix 1:2:4 type B-1 using (20mm graded stone aggregate) for chajjas complete all as specified and directed

M&L for gunniting to RCC works in column beams, slabs, chajja, facia, landing, balconies etc by removing/ dismantling of RCC (loose concrete) and cutting of steel bar including plaster cleaning of surfaces with wire brushes and applying epoxy, paint anti corrosive coating of minimum 40-50 microns thick with sikatop Armatec 108 or Colusal VL of MC Bauchemie to rusted steel reinforcement after removing cleaning all rust and supply and fixing welded steel wire mesh 75mm x75mm with 4mm dia steel wire as facies/drops and similar works etc and expoxy based or other equivalent suitable bonding against treatment to be carried out on old concrete surface with Sikadur 32 of Sikka. Nito bond EP of fosroc or equivalent (as per manufacturers instruction) to bond old and new concrete mixing @ 2% by weight of cement polycrete and providing gunniting with a minimum pressure of 2 to 2.5 Kg sqcm and applying 35mm thick gunniting in cement mortar (1:2) (one part of cement and two part of river /ghaghar sand) using ordinary port land cement of 43 grade over wherever required, complete all as specified and directed by Engineer-in-Charge. Note:-(i)After placing the additional reinforcement all concrete surface shall be thoroughly scrubbing with. (ii) Additional reinforced TMT bars where incorporated in work and including 20mm thick cement plaster in 1:4. (iii) Work to be carried out as in patches as directed by Engr-in-charge. (iv) Rate for steel scaffolding as directed to be included in quoted rate. (v) All demolished material removed from MOD land completely.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed .

M&L TMT steel bars 6mm to 8mm dia and over cut to length bent shape required, including cranking bending binding with mild steel wire (annealed) not less than 0.9mm dia quality conforming to relevant IS complete all as specified.

Taking down chowkats or frame with shutter (without taking off shutter from the frame) size not exceeding 1.50 sqm each complete all as specified and directed

S &F Floor door stopper of aluminium alloy 150mm body and tongue, anodised, with hard drawn steel spring. Fixed in floor complete all as specified and directed

S&F for Aluminium alloy, anodised sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded section of length of bolt in 200mm complete all as specified and directed

S&F aluminium anodised 100 mm long skeleton tower bolts with plate, staples and bolt of extruded section and fixed complete all as specified and directed

S&F aluminium anodised 100 mm handle cast type, anodised complete all as specified and directed

S&F aluminium anodised 100 mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed

S & F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube fixed in opening complete as per manufacturer's specifications and as directed by Engineer-in-Charge

S & F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings as as directed by Engineer-in Charge.

S&F 18 mm thick with min density 600 Kg/cum LEAD FREE PVC Celuka ply of single side rigid laminate of approved colour and other side plain white colour fixed with SS screws and solvent cement/ adhesive to make kitchen cabinet shutters complete as per manufacturer’s specifications complete all as specified and directed. MAke:- Rajshree / Jindal /Ecocell or equivalent out of make specified in list of makes. Note:- For the purpose of payment sides, top & bottom shall be measured and considered for the purpose of payment.

S&F auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position complete all as specified and directed.

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs, complete all as specified and directed.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position all as specified and directed.

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions complete all as specified and directed.

S&F Stainless Steel 304 grade wire Basket (avg. wait 2.5 to 4 Kg. per basket) of pull out type like plain/cup&saucer/bottle/multi purpose/2-3 shelf baskets etc. for kitchens of required size complete all as specified and directed.

S&F Stainless Steel 304 grade Basket Cutlery of size 370X485mm premium quality complete all as specified and directed.

S&F 18/19mm thick Preliminated particle boards interior grade,preliminated one side with dacorative choice lamination & other side blancing white lamination fixed with screws to timber frame work complete all as specified.

Extra over item of Prelaminated particle board for external teak wood lipping, 6mm thick, fixed with nails suitable for 18mm thick complete all as specified and directed

S&F continous (piano)hinges mild steel,bright finish or electro galvanised width of flaps (when open)in mm 30mm complete all as specified and directed

S &F Hasp and staple, Alumimium anodised length 75mm length, including bolt to hinge plate and fixed with screws complete all as specified.

M&L for Second class Hard wood,plain solid straight chowkats and frames rebated on the solid, ,rounded or chamfered put together with glue pinned at joints, supplied and fitted all as specified and as directed.

Dismantling existing tanks Exc 250 litre and n exc 500 lit capacity and removing from site complete all as specified and directed.

S & F 500 ltrs Rotational moulded polyethylene water storage tanks three layer (cylindrical vertical with closed top) hoisted and fixed in position all as per specified and directed.

S &F in repair Ball valves 20mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./ 25mm-455gms/ 40mm - 690 gms)

S& F Tank adaptor GI 20mm dia complete all as specified.

Taking down or up 15 mm bore galvanised iron tubing and connection including cleaning for refixing or removal from site complete all as specified & directed

All as per item No 30 here in before but 20 mm bore complete all as specified and directed

S & F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified.

All as per serial item 32 here in before nut 20 mm bore

Refixing only old GI tubing 15 mm bore pipe and connections in new or old position as on walls ceiling floors etc all as specified (i) Cleaning of pipe is included in ser No 30 & 32 here in before (ii) Rates quoted by the contractor deemed to be included S & F new fittings as required

All as per serial item 34 here in before but 20 mm bore

S & F 20 mm bore stop valve cast copper alloy screwed down high pressure with crutch for butter fly handle screwed both ends for iron pipe complete all as specified and as directed

Taking down cement plaster including raking out joints hacking for key and scrubbing down with water and removal of debis from outside MoD land complete all as specified and directed

M & L 10 mm thick rendering in CM (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M & L 15 mm thick rendering in CM (1:4) on fair faces of brick work or concrete surface finished even and smooth without using extra cement with using water proofing compound (WPC will be measured and paid separately)

M & L for rendering 5 mm thick on ceiling on fair faces of concrete surface in CM 1:3 finished even and smooth without using extra cement all as specified

M & L for preparation of new plastered surfaces of walls and applying two coat of Oil Bound distemper of approved tint, over a coat of 3mm thick wall care putty over a coat of primer complete all as specified.

M & L for preparation of newly plastered surfaces and applying two coats of cement base paint on walls,facia and chajja complete all as specified.

M&L for preparation of newly plastered surfaces of ceilng and applying 3 coats of white washing on internal/ external ceiling complete all as specified.

M&L for preparation of old plastered surface of ceiling and applying one coat of white wash complete all as specified and directed by Engr-in-charge

M&L preparing old distempered surfaces of wall by complete removal of existing treatment and applying two coat of oil emulsion distemper over wall care putty 3mm thick complete all as specified and as directed.

M&L preparation old treated surface by complete removal of existing treatment of wall and applying two coat of cement base paint complete all as specified and as directed.

M&L for preparation of old painted wooden surfaces over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M & L preparation of old painted surfaces of steel and iron work of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed

M&L MS Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete (Fe 410-W (Gde E-250) quality B) all as specified and directed.

M&L Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified (Note : Payment for providing grooves shall be made separately).

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as specified and directed.

Taking down rain water pipe and eaves gutters (any size and pattern) including all fittings heads shoes bends swan necks etc complete all as specified and directed

S&F 100mm dia rain water pipe and eaves gutters (any size and pattern) including all fittings heads shoes bends swan necked upto 150mm offset etc complete all as specified and directed

Dismantling of cast iron drain pipe 100mm dia jointed in lead joints or cement joints and taking out of under floors if required complete all as specified and directed

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation and getting out in Soft/loose soil complete all as specified and directed .

Removing excavated soil exc. 250m but n exc 500 m & depositing where directed at a level not exceeding 1.5 m from the starting point complete all as specified and directed

Returning, filling in, including spreading, levelling, watering & well ramming in layers n. exc 25 cm in soft/loose soil complete all as specified and directed.

Cutting into existing man holes for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required as 150mm dia.

Demolition of brick work or stone / boulder masonary, built in cement mortar including all quoins, arches, pillars etc., complete all as specified and directed.

M&L for brickwork with subclass 'B' bricks,straight or curved on plan exc 6m mean radius built in CM1:6 complete all as specified and directed

M&L for providing precast cement concrete 1:2:4 type B-1 in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces chamfers, weatherings, throat- ing etc. and setting in mortar 1:4 complete with joints to match complete all as specified.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

S & F 110 mm bore of pipe PVC (SWR) pipes single socket in any length with rubber ring joint fixed to walls with MS clamps as directed 6 Kg/Sq cm complete all as specified and directed.

S & F 110 mm bore of pipe PVC (SWR) bends of any radius / shoe fixed to PVC pipes as directed

S&F 75mm bore PVC(SWR) pipes single socketed, in any length fixed to walls/laid in floors/trenches all as specified and directed

S&F PVC (SWR) bend any radius with access door suitable for 75mm dia pipes complete all as specified and directed

S&F PVC SWR branch piece single 'Y' equal or unequal 110mm bore with access door complete all as specified and directed.

S&F PVC SWR branch piece single 'Y' equal or unequal 75mm bore with access door complete all as specified and directed.

S&F PVC (SWR) Vent cowl suitable for 110mm dia vent pipe complete all as specified and directed

S&F PVC (SWR) Vent cowl suitable for 75mm dia vent pipe complete all as specified and directed.

S&F PVC floor trap,75mm outlet dia plain with grating including joining with solvent cement all as specified and directed

S&F PVC gully trap,125/110mm outlet dia including joining with solvent cement all as specified and directed

S&F Shelf of PTMT fixed with and including chrominium plated brass screws and wooden/plastic cleats (minimum weight 300gm) complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed

M & L for 50 mm thick PCC 1:3:6 type C-2 as in plinth protection, finished even and smooth without using extra cement as specified

Demolition of cement concrete in ground floors and pavings exc 15 cm thickness above ground level as in sunken floors etc complete all as specified and directed.

M & L for 50 mm thick PCC 1:2:4 type B0 using 12.5 mm graded aggregate using water proofing compound as in sunken floor complete all as specified and directed. (Note:- WPC shall be measured and paid separately)

M & L Applying evenly a coat of blown type bitumen at the rate of 1.50 kg/sqm and binding with clean dry sand @ 0.05 cum per sqm complete all as specified and directed.

M & L for rendering 15 mm thick in CM 1:3 with using water pcomplete all as specified and directed.

Supply only integral water proofing compound of approved quality complete all as specified and directed

M & L PCC 1:5:10 type E2 (40mm graded aggregate) as in sub base of floor mass filling using 40 mm graded aggregate with using water proofing compound complete all as specified and directed.

S & F GI tubing medium grade with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 32 mm bore (Spout pipe for sunken portion) complete all as specified and directed.

S&F in repair vitreous china wash basin, white, flat back, size 550 mm x 400 mm fixed on and including cast iron cantilever bracket 32 mm dia brass waste coupling and including fixing of tap, waste fitting and union complete all as specified and as directed.

Supply only 15 mm dia bore pillar taps fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or “cold’ with long screwed shank and flynuts, screwed for iron pipe and fixed complete all as specified and as directed

Supply only 32mm dia waste cupling fitting brass chromium plated for basin with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S & F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm of approved quality

S & F 15 mm chromium plated cast copper alloy bib taps with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F in repair brass CP kitchen sink mixer for mixing hot & cold water screwed down for iron pipe all as specified and as directed by Engr-in-charge.

S&F in repair brass CP mixer for mixing hot & cold water screwed down for iron pipe all as specified and as directed by Enginerr-in-charge

S & F in repair 15 mm dia bore angle Cock with Flange chromium plated fancy type with long shank & cup (concealed type) complete all as specified and as directed.

S&F in repair kitchen sink with drainage board made out of 1mm thick stainless steel with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever bracket and connecting union to pipe over all size 915 mm X 460 mm & bowl size 410 mm X 330 mm X 160 mm complete all as specified and as directed.

S&F Brass in repair chromium plated tubular towel rail 20 mm dia D type, 60 cm long between flanges complete all as specified and as directed.

S&F in repair Swivel shower of PTMT any colour for fixing with 15mm pipe (Minimum weight 40gms) including shower arms 15 mm size 195 mm long with bend complete all as specified.

S & F in repair Vitreous China squatting pan of pattern “long pan”, size 580 mm white with ‘P’ or ‘S” trap, front or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe incl cement concrete bedding and connection to antisyphonage pipe etc including CI 'P' trap dia 100 mm thick complete all as specified

Supply only PVC low level cistern of 10 litre capacity inclusive of brackets and PVC bend long type and connectin to flush pipe of any size and pattern with inlet ball valve float and handle complete of approved make

Dismantling floor hearth or wall tiles including cement mortar (but not backing) removing serviceable tiles from site and rubbish off the premises complete all as specified and directed

S&F Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, set and jointed in neat cement slurry and pointed in colour cement as in floor over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as dierected.

All as per srl No. 98 here-in-before but on vertical surfaces including 10 mm thick rendering in CM 1:4 -ditto-.

M & L Glazed coloured ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick over 10 mm thick plastering in CM 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and as dierected.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement to match the shade of the slab including rubbing and polishing, including 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as dierected.

M&L machine cut kota stone slab flooring 20-25mm thick in riser of steps,skirting,dado and pillar laid over 10mm thick cement screed base1:4 laid and jointed with grey cement to match the shade of the slab including rubbing and polishing

Rounding to edge of stone slabs one edge such as steps, cooking platform and other similar situatiion complete all as specified and as dierected.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.including 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as dierected.

M&L for plain Cement concrete type B-2, 1:2:4 (40mm graded stone aggregate) 75mm thick for surafce finish complete all as specified and as directed.

M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with gray cement and pigments including 20mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and as dierected.

S&F M.S square/circular tube M.S pipe etc conforming to IS-1161-1979 garde grade YST 240 fixed with fastener complete all as specified and directed.

M&L Galvanised Iron steel wire 4mm dia fixing to wall and pole complete all as specified and as directed.

Removing existing roof treatment and preparing surface to the entire satisfaction of Engineer-in-Charge/ GE including taking down existing plaster, cleaning of all foreign material such as grass roots dust etc and roughening the concrete surfaces by wire brushes and washing down to remove dust etc flushing at junction of parapets complete and removing the same to he places where directed by Engineer-in-Charge

M&L for 40mm thick cement concrete type B0, 1:2:4 (20 mm graded aggregate) as in floor/roof including waterproofing compound including finishing cement concrete using extra cement complete all as specified and directed.

M&L Providing cement concrete type B 1:2:4 (12.5mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M&L for 15 mm thick cement plastering on fair faces of brick and concrete surface in CM 1:4 of roof and parapet, mixed with water proofing compound, finished even and smooth without using extra cement upto and Including 4 Story building complete all as specified and as directed by Engineer-in-Charge. Note :- Water proofing compound shall be measured & paid separately.

M&L apply evenly a priming coat with bituminous primer at 4 kg per 10 sqm complete all as specified and as dierected.

M&L APP based polymeric membrane minimum weighing 3kg/sqm minimum 3mm thick reinforced with polyster non wove fabric (weight not less than 150 gms/sqm) land on primed surface by forced application with overlapping 150mm complete all as specified

M&L preparation of surface and applying two coat of aluminium paint on APP membrane, over 10 cm in width or girth not otherwise described complete all as specified and as directed

Note:- The amount of Rs 20128/- against Schedule of Credit on Page No 144 shall be deducted from the total amount quoted against Sch 'A' while deriving the Contract Sum for Acceptance

PAWAN KUMAR

M/S ujjwal associates

M/s Vijay Enterprises

Green Leaves