Provision of certain revenue work LBW work and Special repair work in the area of AGE B/R I under GE (N) Ahmednagar

Amount

Dismantling of stone slabs and floor tiles of any description or thickness in floors, approns etc laid and bedded in any mortor etc complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises etc complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm in thickness (below or above ground level) etc complete all as specified and directed by Engineer-in-Charge.

M&L for 75mm thick PCC (1:3:6) type D-2 using 40mm graded stone aggregate as in sub base etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for joint free / rectified ceramic coloured tiles SSR series of Johnson / FT Series of Orient-Bell / Duro Cotto Series of Nitco or equivalent in Kajaria makes as specified in PS, 8-10 mm thick as approved by GE (square / rectangular) area of each tile exc 0.18Sqm but not exc 0.38 Sqm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

All as per Sl item No 5 (here-in-beofre) but in skirting including 10mm thick in cement and snad morttar (1:4)

Material and labour for joint free / rectified anti skid ceramic coloured tiles matching to wall tile, makes as specified in PS, 7-8 mm thick as approved by GE (square / rectangular) area of each tile exc 0.06Sqm but not exc 0.11 Sqm, as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

Material and labour for coloured glazed ceramic tiles digitally printed premium designer series of size exc 0.12 Sqm and n'exc 0.18 Sqm , 7-8 mm thick as approved by GE as in dado/skirting or on vertical surfaces, over and including 10 mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L for Shahabad stone 20mm to 25mm thick flooring incl 15mm thick screed bed or bedding etc complete all as specified and directed by Engineer-in-Charge.

M&L machine cut cudappa stone slab 20-25 mm thick over cement screed base, laid over and including 15 mm thick screed bed in cement and sand mortar (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge.

M&L for granite(of any type) work(table rubbed and polished) cooking platform and like set in cement and sand mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigment to matach with shade of granite thickness of granite 18 to 20mm etc complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering, 15 mm thick on any type of face of block / stone masonry surfaces, concrete surface in cement and sand mortar (1:4) on wall or roof finished even and smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering, 15 mm thick on type of face of stone masonry surfaces in cement and sand mortar (1:6) on wall finished even and smooth without using extra cement with sagol finish etc complete all as specified and directed by Engineer-in-Charge.

M&L for rendering, 10 mm thick on concrete surfaces in cement and sand mortar (1:4 )on ceiling surface finished even and smooth without using extra cement with sagol finish etc complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of old / new surfaces of walls & applying two coats of acrylic (antifungal) exterior grade paint on wall & etc complete all as specified and directed by Engineer-in-Charge.

M&L for applying two coats of oil bound distemper on newly plastered surfaces of walls over 3mm thick wall care putty including preparation of surfaces etc complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment and applying two coats of OBD over 3 mm thick wall care putty on plastered surfaces of walls including preparation of surfaces etc complete all as specified and directed by Engineer-in-Charge.

M&L for applying 2 coats of white wash on newly / old plastered surfaces including preparation of surface etc complete all as specified and directed by Engineer-in-Charge.

M&L for applying 2 coats of white wash on newly / old plastered surfaces incl preparation etc. complete on ceiling etc complete all as specified and directed by Engineer-in-Charge.

M&L for 2nd class hardwood sectional area exc 15 but n.exc 25 sq. cm clean swan battens at 15 cm centers etc complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on roof slab tec. Including raking out joints, hacking for key, scrubbing down with water, etc any description etc complete all as specified and directed by Engineer-in-Charge.

M&L for screed bed or bedding layer of mortar 10mm thick in cement and sand mortar (1:3) by using 100% course sand on roof/chajja mixed with & including M&L for WPC @ 3% by weight of cement and finished the surfaces even and smooth without using extra cement to receive water proofing treatment etc complete all as specified and directed by Engineer-in-Charge.

M&L for providing waterproofing treatment on roof / chajja as per latest zonal specification, as per manufacturer's instructions and as specified after taking down / out as existing as site etc complete all as specified and directed by Engineer-in-Charge.- (a) M&L for cleaning the newly plastered surface with wire brushes and applying two coats of bituminous primer @ 0.25ltrs/sqm and allow to dry. (b) M&L for applying and laying torch APP polymer midified bituminous membrane 3mm thick with non woven polyster matt as reinforced weighing not less 3 kg / Sqm with white gravel/mineral finished by thermofusion process.

Supply and fix asbestos cement corrugated or semi currugated sheets, 6 mm thick as in roofs, walls fixed with 'L' type or 'J' type or cranked hook bolts etc complete all as specified and directed by Engineer-in-Charge.

S&F asbestos cement pain angular ridge 6 mm thick fixed with L type or J type or cranked hook bolts etc complete all as specified and directed by Engineer-in-Charge.

Taking down steel windows / ventilators frame of size 105 x 60 mm etc complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames n exc 1.5 sq. m Each with shutters (without taking off shutters from the frame) etc complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm Each etc complete all as specified and directed by Engineer-in-Charge.

Supplied and welding standard projecting / box, butt hinges for steel windows in repairs etc complete all as specified and directed by Engineer-in-Charge.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded etc complete all as specified and directed by Engineer-in-Charge. NOTE: Wire cloth, glass, guard bars and painting shall be measured and paid separately.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, etc complete all as specified and directed by Engineer-in-Charge. NOTE: Wire cloth, glass, guard bars and painting shall be measured and paid separately.

S&F Mild steel TMT bars 8mm to 10mm dia in distribution, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips incld cutting & removal of old decayed reinforcement etc complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones etc complete all as specified and directed by Engineer-in-Charge.

M&L for glazing with 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in Each pane etc complete all as specified and directed by Engineer-in-Charge.

M&L for glazing with 3 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in Each pane etc complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 37 (here-in-before) but fixed in repairs.

M&L refixing in same opening shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm Each etc complete all as specified and directed by Engineer-in-Charge. (Note:- 'Refixing' includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.)

S&F 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated etc complete all as specified and directed by Engineer-in-Charge.

S&F 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair pressed steel frames (Size 125 x 60mm) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix PVC door frame made out of PVC section 40 mm x 48 mm with special polymeric reinforcement at necessary places to hold the screw all as specified and directed by Engineer-in-Charge Make : Sintex or equivalent in as specified in PS.

Supply and fixing Factory Made Solid PVC Moulded Door Shutter, with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face

S&F 100 mm long butt hinge, medium weight, cold rolled mild steel etc complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm long butt hinge, medium weight, stainless steel etc complete all as specified and directed by Engineer-in-Charge.

S&F 200 mm long mild steel barrel tower bolt, stove enamelled black, with bright bolt etc complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long mild steel pressed handles, oval type, stove enamelled black etc complete all as specified and directed by Engineer-in-Charge.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and directed by Engineer-in-Charge.

S&F 200 mm long aluminium anodised barrel tower bolt, of extruded sections etc complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long aluminium anodised handle, cast type etc complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring etc complete all as specified and directed by Engineer-in-Charge.

M&L preparation of old/new painted steel surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint etc complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer etc complete all as specified and directed by Engineer-in-Charge.

M&L preparation of old painted wooden surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint etc complete all as specified and directed by Engineer-in-Charge.

S&F 18/19 mm thick MDF board exterior grade including 4 mm thick Teak Wood beading alround the top fix as directed by Engineer-in-Charge

M&L for plain fillets, square, rectangular or triangular in section, wrought, secured with nails or brads, sectional area exc 3 & n.exc 6 Sq.cm of 2nd class hard wood etc complete all as specified and directed by Engineer-in-Charge.

S&F continous (piano) hinges, mild steel, bright finish or electrogalvanised (width of flaps 30mm ) etc complete all as specified and directed by Engineer-in-Charge.

S&F 125mm hasp and staple, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair harrison rails, mild steel, chromium plated curtain rods with fixing brackets, stops, rollers etc. all as specified and directed.

Dismantling of water tanks of capacity exc 500 ltrs but n.exc 1000 ltrs and removing from site all as specified and directed.

S&F rotational moulded polythene water storage tank 1000 ltr capacity vertical with closed top hoisted and fixed in position all as specified in SSR part-I etc complete all as specified and directed by Engineer-in-Charge

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore fixed all as specified and as approved by GE/Engineer-in-Charge.

S&F ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in 20mm dia bore pipe all as specified and directed.

Taking up or down 15 mm dia steel GI tubing including all connected fittings of any dia and in any position and removing to store etc complete all as specified and directed by Engineer-in-Charge

All as per item No 65 (here-in-before) but 20mm dia pipe.

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling etc complete all as specified and directed by Engineer-in-Charge.

All as per item No 67 (here-in-before) but 20mm dia pipe.

Taking down rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks etc., including cleaning or refixing or removal to Store (measured overalll as fixed along the cente line over fittings and accessories)

S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls etc complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls etc complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm dia PVC (SWR) vent cowl etc complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) branch piece double (single Y) equal or unequal etc complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm dia PVC (SWR) bend any radius etc complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm dia PVC (SWR) bend with access door any radius etc complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) floor trap, 75 mm dia with grating including jointing with solvent cement etc etc complete all as specified and directed by Engineer-in-Charge.

S&F in repair chromium plated grating 100mm dia etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repair bib tap, 15 mm bore CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule all as directed.Make:- (Cat part No MOR 1020 A(Orintal series) of MARC or equivalent in PLUMBER, ESS-ESS)

Supply and fix 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.Make:- Cat part No MOR 1010(Orintal series) of MARC or equivalent in PLUMBER, ESS-ESS

Supply and fix in repair stop valve, 15 mm dia, cast copper alloy,screwed down high pressure screwed down high pressure with cruitch or butterfly handle screwed both ends for iron pipe or for unions all as directed. Make:- Cat part No MOR 1320 (Orintal series) of MARC or equivalent in PLUMBER, ESS-ESS

Supply and fix in repairs, shower rose with shower arm from Make:- Cat part No MARC MSR1050 (Shower) and MOR 1260(Shower arm) from MARC or equivalent in Make Plumber,ESS-ESS.

Supply and fix tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets all as directed. Make:- (Cat part No UO911 of PLUMBER or equivalent in MARC, ESS-ESS(

Supply and fix in repairs looking mirror of size 600 mm X450 mm all as directed. Make:- Cat part No C 8606 Of Parryware or equivalent in Jaquar / Cera

Supply and fix in repairs wash hand basin vitreous China coloured , flat back pedastal pattern of size 630 X 510 mm, (for hospital use) waste chain and plug and porcelain stopper, waste pipe, incl cutting for and pinning in ends of brackets in cm 1:3 etc complete all as .Make :- Cat Part No S2040111 & S2090107 Of Cera or equivalent in Parryware / Hindware

S&F in repairs 32 mm dia high density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed etc complete all as specified and directed by Engineer-in-Charge.

Supply and fix repairs PVC valveless, syphonic action type, flushing cistern,low level, all accesories all as directed. Make :- Sleek essence series of Hindware or Cat part No E8303 of Parryware of equivalent in Cera

Supply and fix in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistren complete all as specified and directed. Make :- Cat Part No C0117 Of Parryware or Cat Part No 20042 of Hindware or equivalent in Cera

Dismantling of false ceiling boards (fibre, pulp, insulation, etc,) or any type ceiling board any thickness including cover fittets etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for false ceiling with 4 mm thick plain non asbestos building 'E' board with decorative finish water proofed on one side fixed on and including powder coated GI fabricated grid of 60 cm X 60 cm made out of main runner of 'T' section of size 32 mm X 24 mm X 0.30 mm, cross runner made out of 'T' of section of size 24 mm X 24 mm X 0.30 mm and alround angular section of size 22 mm X 22 mm X 0.70 mm with GI clip and level adjuster duly suspended by 4 mm dia GI wire fixed to roof at 1200 mm centre to centre as per manufacturere's instructions and etc complete all as specified and directed by Engineer-in-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in Hard/dense soil.

M&L for Cement concrete Type D2 (1:4:8) (40mm graded stone aggregate) as in foundations, filling and mass concrete etc complete all as specified and directed by Engineer-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and directed by Engineer-in-Charge.

S&F Steel work in tubular trusses including special shaped washer using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 etc complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new steel surfaces over 10cm in width or girth & applying 2 coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and directed by Engineer-in-Charge.

M&L for Pre-cast cement concrete block masonry Type C1 (1:3:6) (20 mm graded stone aggregate) with solid blocks, exc. 10 cm in width and setting in mortar Set in cement and sand mortar (1:6), etc complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:2:4) type B-1 ( 20 mm graded stone aggregate) as in coping etc complete all as specified and directed by Engineer-in-Charge.

M&L for applying Rendering 15 mm thick in cement and sand mortar (1:4) on fair faces of brick work and finished even and smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge

M&L for applying two coats of white washing on newly plastered surfaces incl preparation of surfaces etc complete all as specified and directed by Engineer-in-Charge.

M&L for hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface in broken stone or buodlers (15 cm compacted thickness).

M&L Machined pressed precast concrete interlocking paver block glossy finished with grey cement and pigment, any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade over a stone dust cushion of 30mm thick etc complete all as specified and directed by Engineer-in-Charge.

S&F medium grade MS pipe as in compound griders and stations, lattice girders aerial masts, staging for water tanks and the like including caps, bases, splices etc with plates including all lattice bars, stiffners gusset plates etc conforming to Gde Fe - 410-S etc complete all as specified and directed by Engineer-in-Charge.

M&L for roof trusses (framed) trussed, Purlins crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Gde Fe- 410-S etc complete all as specified and directed by Engineer-in-Charge.

Labour only for machine pressed precast concrete inter locking paver block glossy finished rubber moulded coloured and shape and size conforming to IS-15658-2006 of 80mm thickness M-40 grade with cement and pigment laid dry over 30mm thick stone dust or sand base and compacted using vibrator etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for Vitrified ceramic tiles Full body vitrified tiles GVT series of Johnson or equivalent in makes specfified in PS ,10 mm thick (square / rectangular) of size 600 x 600 mm of any shade as approved by GE in floor etc laid over and including roughning existing surface , making good the damaged surface, levelling, and fixing with cement based tile adhesive ( Make FOSROC, DR FIXIT) as per the manufecturer's instructions and pointed in white or coloured cement to match complete all as specified.

All as per item No 104 (here-in-before) but on skirting

Material and labour for special treatment to sunken slab floor incl WC trap etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementious grout and applying 10mm thick cement plaster in CM 1:4. Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished rainforced with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc and preparing the surface complete. and providing PCC 1:5:10 type E2 using 40mm graded mechanically crushed stone aggregates in sunken slab and 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, 40mm bore GI pipe, light grade of length not less that 50 cm as spout, non-skid glazed tiles as per existing pattern/size/tint with and incl WC viterous china squatting pan 580x440mm with integral footrests/pedastal pan incl seat cover, white, area of WC exc 1.00 Sqm but nexc 5.00 sqm etc after dismantling the existing sunken floor etc complete all as specified and as directed Make : Super Thermolay MT of STP / TEXSA / FosRoc Note : Work has to be carried out strictly by the authenticated applicator of the manufacturer and as per manufacturers specification as approved by GE duly tested for leak proof.

Supply and fixing in repairs vitreous china wash down water closet (Pedestal pattern) white including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device complete connecting to 'P' or 'S' trap all as directed. Make:-Petite series Cat part No C0287(S)/88(P) Incl seat cover Cat part No E8309 of Parryware or equivalent in Hindware or Cera

Supply and fix in repair health faucet (hand shower) with 8 mm dia 1 m long flexible tube wall mounted / hooked all as per Cat Part No 573 of JAQUAR OR ITS EQUVIVALENT IN MARC / PLUMBER all as directed.

Supply and fix in repairs wall mixture , wall mounted with bend and over head shower all as per Cat Part No MSH 1141 (for mixer) ,MSR 1090 (Over head shower)and MSH 1260 (Shower arm) of MARC OR its equivalent in Plumber, ESS-ESS

S&F in repairs decorative towel ring recangular chromium plated fixed with (CP) brass screws of approved qualityas specified Make : Cat Part No EG-7010 of Plumber or equivalent in Marc / ESS-ESS

PVC mirror cabinet of size 16" X 16" with napkin rail in ivory colour MAKE: Prayag / Polytuff

S&F in 10 mm thick toughen glass for shelves in corner. Make : Cat part No U0921 of Plumber or equivalent in Marc / ESS-ESS

S&F in repair Brass Chromium Plated toilet paper holder fixed with (CP) brass screws of approved quality etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing stainless steel kitchen plate rack made out of 0.63 mm thick stainless steel sheet of size 750x900mm including screws complete all as specified and as directed. Make :- Cobra / Diamond / Neelkanth / Nirali

Supply and fixe in repairs stainless steel kitchen sink matt finish without draining bowl size 410 X 410 X 230 mm, made out of 1.00 mm thick SS sheet of high quality including a pait of brackets, waste coupling, plug and chain, 32 mm dia PVC flexible waste pipe and nahani trap complete all as specified and directed. Make : (i) Model Omni mini Satin Finish of Nirali or equivalent in Dimond / Neelkanth

Supply and fixe in repairs stainless steel kitchen sink matt finish with draining over all size 950 X 510 mm and bowl size 410 X 410 X 230 mm, made out of 1.00 mm thick SS sheet of high quality including a pait of brackets, waste coupling, plug and chain, 32 mm dia PVC flexible waste pipe and nahani trap complete all as specified and directed. Make : (i) Model Olympia Satin Finish silent square range of Nirali or equivalent in Dimond / Neelkhant

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. and n exc 1.5 m in depth and getting out etc complete all as specified and directed by Engineer-in-Charge.

Excavation over area n. exc. 1.5m deep and getting out in soft/loose soil etc complete all as specified and directed by Engineer-in-Charge.

M & L for RCC M-25 as in foundations, including rafts, footings, foundation beams; plinth beams etc. and mass concrete etc complete all as specified and directed by Engineer-in-Charge.

Removing excavated soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point etc complete all as specified and directed by Engineer-in-Charge.

S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

M&L for returning filling in including spreading, loevelling water and well raming in layers not exc 25cm. etc complete all as specified and directed by Engineer-in-Charge.

M&L for removing excavated material n.exc 250m and depositing where directed at a level n. exc 1.5m above the starting point etc complete all as specified and directed by Engineer-in-Charge.

Taking down carefully aluminium point wiring (light, fan, bell, socket, power point etc.) with or without conduit, casing caping, along with all connected accessories such as ceiling rose, switches, sockets, switch boards, fan regulator etc complete all as specified and directed by Engineer-in-Charge.

M & L for point wiring complete with two runs of 1.5 Sqmm for phase and neutral single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS cable drawn through and including PVC casing & capping heavy grade of suitable size with necessary accessories with plastic surface boxes (upto 18 moudule suitable for Mylinc series of Legrand including white plates with frame upto 18 module of make suitable for Mylinc Series) housing of switches etc (Note :- The cost of Modular mounting boxes and modular plates included in the quoted rates)

(a) One light point controlled by one, one way switch single pole.

(b) One Fan point controlled by one, one way switch single pole.

(c) One 3 pin 5 Amps socket out let on independent board

(d) One 3 pin 5 Amps socket out let on Sameboard

(e) One bell point controlled by one bell push on independent board

All as per item No 129 here-in-before but with 2.5 Sqmm Copper conductor cable for one 3 pin, 15 Amps socket out let on independent board.

Supply and fixing 6 A one-way SP switch - 1 module etc complete all as specified and directed by Engineer-in-Charge Make Legard Cat No: 6755 01 or equvalent in Simens / Carbtree

Supply and fixing 16 A one-way SP switch - 1 module etc complete all as specified and directed by Engineer-in-Charge Make Legard Cat No: 6755 11 or equvalent in Simens / Carbtree

S & F 6 A 3 pin universal socket 2 modules etc complete all as specified and directed by Engineer-in-Charge Make Legard Cat No: 6734 52 or equvalent in Simens / Carbtree

S & F 6/16 A socket 3 Pin 2 modules etc complete all as specified and directed by Engineer-in-Charge Make Legard Cat No: 6734 55 or equvalent in Simens / Carbtree

S & F 6 A one-way SP bell push - 1 module complete all as specified & directed SP switch - 1 Make Legard Cat No: 6755 04 or equvalent in Simens /Carbtree etc complete all as specified and directed by Engineer-in-Charge

S & F Fan regulator 100 W with 360° rotation 2 module complete all as specified and directed.Make Legard Cat No: 6759 64 or equvalent in Simens / Carbtree etc complete all as specified and directed by Engineer-in-Charge

S & F bell, AC, 230 Volts, single pole etc complete all as specified and directed by Engineer-in-Charge

S & F ceiling rose surface bakelite 65mm x 50mm three terminal etc complete all as specified and directed by Engineer-in-Charge

S&F lamp holder, PVC / Polycarbonate type with cord grip cap suitable for LED lamps ncluding LED lamps including LED lamp 7 watt of make Philips / Jaquar / Wipro all as specified and directed. Note : Quoted rates including cost of LED lamp 7 Watt

S & F in replacement double door Sheet metal enclosures factory made DBs 8 way ,240 volts ,protection class IP-42, suitable for fixing of MCBs, Isolators etc, confirming As per IEC 61439-3 ,Suitable for Flush Mounting and Surface Mounting, With 100 A Copper Busbar ,With Neutral bar, Earthbar and Cable ties for Cable management,Fully shrouded Neutral bars, Prefitted masking sheet etc complete all as specified and directed. by Engineer-in-Charge Make: Legrand ,Cat No: 5076 11 or equivalent in Simens/ L & T

S&F isolators of the under mentioned type and rating and fixing in DBs (DBs measured and paid for separately under relevant item of this BOQ / Schedule `A') (Note :- Make of the isolator should be the same as that of DB) for the following :-

(a) MCB Single Pole of 240 volts 5-32 Amps,10 KA Capacity, 'C' series of Make: Legrand ,Cat No: 4085-87 to 90, 92, 93, 94, 95 or equivalent in Simens/ Hager

(b) MCB Single pole + Neutral 240 volts, 32 -63 Amps,10 KA Capacity, 'C' series of Make: Legrand ,Cat No: 4086-17 to 20 or equivalent in Simens/ Hager

Taking down Existing tube light fitting & Supply & fix Endura LED Batten fitting 20 watt with minimum 2000 lumens including connecting up with thre core twisted flexible copper conductor cable with suitable size from ceiling rose to fitting all as directed by the Engineerr-in-Charge. Make :- Philips ,Model no BN108C LED 20S PSU CDL WH or Equivalent in Wipro / Havells / Wipro / Jaquar

Taking down existing tube light fitting and supply and fix linear and compact 9 W mirror light with decorative grey and caps, polycarbonate body and ribbed opal diffuser Make : Havells : 9W LED 4000K LHEXARP6PN1W009/ or equivalent in Phillips / Jaquar / Wipro

M & L for Earthing complete with galvanized steel earth plate electrode 60x60cm x 6.0 mm thick buried directly in ground ( earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 mtr below normal ground level connected to and including galvanised earth lead wire 4.0 mm dia,by means of nuts,bolts,checknuts and washers of galvanized iron including 15 mm bore GI pipe,medium grade up to 7.5 meters long all as shown in electrical plate No.3 of MES SSR part-I and testing on completion including excavation and earth work in any type of soil, PCC (1:3:6) type C1 chamber,precast RCC slab 50mm thick in cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric or XPM,( weight not less than 4 Kg/Sqm), with cast iron frame, funnel with wire mesh,GI watering pipi 20 mm dia medium grade,test point and lugs complete. NOTE:-(i) Items includes the cost of 7.5 metre length GI pipe and earth lead for protection of earth lead.Any variation in length shall be adjusted through deviation order.(ii) On testing,if the earth resistance is not obtained,earthing will be regenerated at no extra cost till the desired earth resistance is obtained.

M&L for sub main wiring with two runs of PVC insulated and unsheathed FRLS cable 650/1100 Volts grade, conforming to IS-1536-1977 multi-stranded 4 Sqmm single core, copper conductor drawn through PVC casing caping and 2.5 Sqmm single core multistranded copper conductor FR PVC insulated and unsheathed cable 1100 volts grade, ISI marked as earth continuity wire etc complete all as specified and directed by Engineer-in-Char (Note : Two runs of conductor with one run of earth wire and PVC casing capping will be measured & paid as one unit) etc complete all as specified and directed by Engineer-in-Charge

Taking out old building security light ( HPSV/Tube light fitting) & S & F LED bldg security light 25 Watt New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium roadway luminaire with high power LED as light source of capacity 25W LED 5000K of Make Havells Cat No.LHEWDRP7PN1W025 or Eq in /Philips/Osaram /Jajuar/Wipro etc complete all as specified and directed by Engineer-in-Charge

Supply and fix in replacement industrial type switch socket for Geysers with 20 Amps MCB Make : Legrand Cat No 6078 41 20 A SP complete or Equivalent in L & T / Simens etc complete all as specified and directed by Engineer-in-Charge

Taking down existing unserviceable CFL / Bulb and S& F LED lamp 10 Watt etc complete all as specified and directed by Engineer-in-Charge

M&L for Supply, laying,connecting, testing and commissioning and jointing in replacement , LT UG cable, 1100 Volts, heavy duty XLPE insulated,armoured with galvanised round steel wire or steel strip electric poer cable heavy duty with multistranded aluminium conductor of size 16sqmm,4 Core, laid in ducts,fixed on poles / walls with proper size saddles and clamps etc complete all as directed. Make : Polycab / Havells / CCI (a) LT cable 10 Sqmm 4 core

Supplying, installing ,commissioning and testing water heaters (Geysers) type electric tank 25 Ltrs capacity 230 volts,AC 5 STAR RATING incl ,grouting nut ,bolts& washers, making electric and water connection to make functional ,making holes in existing wall after cutting chases and making good the disturbed surfaces complete all as specified and as directed. Make:- ALTRO- 2, RACOLD equivalent in Havells, Bajaj Note:- PVC inlet/out pipe shall be measured and paid separatly

Supply and fix heavy duty exhaust fan 300 mm sweep, 900 RPM, 230 V, 50 Hz with fixing of fan duly grouted in bolts and connecting with 3 core flexible copper cable of size 1.5 Sqmm all as directed including making holes in wall / window of Make : Havells, Cat No Turbo force / Bajaj / CG

Supply and fix PVC connection pipe complete with brass and terminal size 300 mm long Make : Kohinoor Gold or equivalent

An amount of Rs 19,603.00 shall be deducted from BOQ on account of schedule of credit

G.M. Construction

M/s. N D Karande

M/s AG PATHAN

Ms. S.K. ASSOCIATES

M/S. M. F. Sharif & Co.

Vinod Enterprises

OM SAI ASSOCIATES

R. T. Saluji