EXTERNAL PERIODICAL SERVICES TO OLD BUILDINGS COMPLEX AT CABINET SECTT NEW DELHI UNDER GE E/M BASE HOSPITAL DELHI CANTT-10

Amount

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and as directed.

S&F vitrified tiles of size 600 x 600 x 10mm thick in floors, scratch resistant, fire proof, electrostatically neutral, dust resistant, fixed with adhesive with fevimate-XL resin mortar make- Pidilite or equivalent make approved by GE complete all as specified and as directed.

M&L 20mm thick Granite (of approved shade) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L 12mm thick Granite (of approved shade) work (table rubbed and polished) as in wall lining, (veneering to wall), and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & including 15mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

S&F in repair 16 mm thick, mineral fibre ceiling board, 600 mm x 600 mm size, including grid 25 x 25 x 1.6 mm thick GI powder coated wall angles and 25 x 35 x1.6mm size T runner, suspended at 1200 mm centre to centre and cross T runner of 25 x 35 x 1.6mm size suspended at 600 mm centre to centre, supported by 4 mm dia GI wire from roof/ slab including wall angle and T with interlocking arrangement as required for framing grid suitable for module size 600 mm x 600 mm ceiling etc complete all as specified and as directed. (Make : Armstrong RH Dune 99 or equivalent of Aerolite/Dexun/Anchor)

S&F in repair GI metal false ceiling, laid in plain regular edge, white colour tiles of size 595X595X0.5mm thick, with 8mm drop, made of GI sheet having galvanizing of minimum 120 Gms/Sqm (both side inclusive ) & electro statically polyester powder coated of thickness 60 microns (minimum) including factory painted after bending, ceiling grid shall be following minimum sizes: main T section (24X38X0.3mm 3 metre long), Cross T section (24X25X0.3mm, 6 metre long), wall angle (24X24X0.3mm, 3 metre long), hanger rod 4mm dia, Adjust clip (85X30X0.8mm), soffit cleat (27X37X25X1.6mm), Dash fastener (12.5 mm dia) including dismantling of old frame/ grid work & ceiling board any type, size & position etc complete all as specified and as directed.

Taking down cement plaster on concrete or brick surface of any description etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M & L for 15 mm thick rendering in cement mortar 1:6 on any faces of brick/ concrete wall surfaces, finished fair & even without using extra cement complete all as specified and as directed.

M & L 10 mm thick rendering in cement mortar 1:3, on ceiling surface, finished even & smooth without using extra cement complete all as specified and as directed.

S&F in repair powder coated aluminium window using 63mm X 38mm X 1.6mm chowkhats, with 45mm X 45mm X 1.6mm openable section as in shutter, including 5.5mm thick glass panes of approved make with aluminium beading & rubber packing for fixing glass and including builder hardware such as aluminium handles 100mm - 02 Nos, tower bolts 100mm 02 Nos, hooks and eye - 02 Nos, 150mm, butt hinges 100mm 04 Nos etc complete all as specified and as directed. Note: The window shall be fixed to wall along with necessary rubber packing around the outer frame of window. The quoted rates shall deemed to be included for this provision.

S&F in repair powder coated aluminium fixed window partition of approved design, using 95.6 mm x 44.8mm x 1.6mm frame work, with 5.5 mm thick fixed glass including aluminium beading & rubber packing for fixing glass, area of each panel not exc 1.20 Sqm complete all as specified and as directed.

S&F in repair powder coated (of approved colour), anodised aluminium frame, with partially glazed shutters, single/ double leaf, divided into two glazed panels including aluminium anodised snap beading and rubber gasket/lining for fixing of glass complete all as specified and as directed. The frame and shutter shall be made out of the following sections:- (a) Aluminium anodised door frame 101.60mmx44.45mmx1.60mm fixed with aluminium trust bolt in walls by drilling as directed (b) Aluminium anodised side rail of shutter section 85mmx44.5mm x1.6mm (c) Aluminium anodised top rail of shutter section 114.30mmx44.5mm x1.6mm (d) Aluminium anodised middle rail of shutter section 83.5mmx44.5mm x1.6 mm (e) Aluminium anodised bottom rail of shutter section 101.60mmx45.4x 1.60 mm (f) Aluminium anodised tower bolt 200 mm long - 02 Nos in each leaf (g) Aluminium anodised handle 250 mm long - 02. Nos in each leaf. (h) Glass Panel shall be 5.5 mm thick tinted float glass in Top panel of door. (j) 12mm thick prelaminated particle board, both side laminated, exterior grade in bottom panel. (k) 100 mm Brass Mortice lock, six lever with duplicate keys.

M&L for preparation of new plastered surfaces of wall and applying two coats of Oil Bound Distemper, over and including a coat of alkali resistant primer, over and including 3mm thick cement based wall care putty & sand papering etc complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying two coats of Oil Bound Distemper, over and including a coat of alkali resistant primer, over and including 3mm thick cement based wall care putty & sand papering etc complete all as specified and as directed.

S&F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and as directed.

GLIBS CONSTRUCTION

JIWAN DASS THAREJA AND SONS

VINAY ENTERPRISES

B Kumar and Co

M/S ANIL KUMAR

SETHI ENTERPRISES