CA NO PROVN OF SECURITY WATCH TOWER WITH TOILET FACILITY, SPECIAL REPAIRS TO UNIT PERIMETER WALL AT NTS GURGAON, SPECIAL REPAIRS TO EXTERNAL PLASTER AND ASSOCIATED WORKS IN NEW WAPTI ENCLAVE (BLOCK NO 121,122,123 AND 124) AT VSV GURGAON UNDER AGE B/R

Amount

B/R WORKS Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in loose / soft soil complete all as specified and as directed.

Excavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation etc for shaft wells cess pits manholes, pier holes not exc 10 Sqm on plan in any type of soil and getting out complete all as specified and as directed

Excavation over areas, n exc 1.5 m deep and getting out in any type of soil complete all as specified and as directed

Ditto all as per item No 3 described here-in-before but exc 1.5 m and n.exc 3.0m deep

M&L for plain cement concrete 1:5:10 type E-2, with using 40 mm grades stone aggregates as in foundations and mass concrete etc complete all as specified and as directed

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips etc complete all as specified and as directed

Ditto all as per item No 6 described here-in-before but 6mm to 8mm dia bars

M&L for TMT bars 5 mm dia and over, upto and including 10 mm dia as in stirrups, cut to length, bent to shape required including cranking, bending for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and as directed

M&L for formwork to sides of concrete foundations, col footings, base of col, raft and raft beam, sides and soffits (if any) of foundation and plinth beam and smilar work vertical or to batter etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) design Mix with using 20 mm graded stone aggregates as in foundations including rafts, column footings, plinth beams, etc complete all as specified and as directed

M&L for formwork to sides chullah hoods, chajja, trough and similar items including edges etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as in chajja etc complete all as specified and as directed

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as in Columns, pillars, piers, posts and struts etc complete all as specified and as directed

M&L for formwork to sides and soffits of floor or roof beam, beam and haunching, girders, bressummers, lintels cantilevers, shelves including supports, overhangs etc also splays between floor and beam etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as in beam, cantilevers, bressumers, lintels over 1.5 mtr span etc complete all as specified and as directed

M&L for formwork to soffits of suspended slab such as roof slab, floor slabs, landing and similar work (horizontal or slopping ) etc complete all as specified and as directed

M&L for formwork to soffits to edges of concrete flats, teads, breaks in floors, window, cills, concrete railing opening in concrete walls, floors and roofs not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but not exc 20 cm wide etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as slab supported on walls, and coloumn in floors, roofs, landing, balconies, canopies, deck slabs and shelves and the likeetc complete all as specified and as directed

M&L for formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses etc complete all as specified and as directed

M&L for formwork to spiral staircase with sloping or stepped soffits, including risers and stringers (excluding landing) etc complete all as specified and as directed

M&L for providing reinforced cement concrete (M-25) Design Mix with using 20 mm graded stone aggregates as Spiral staircases (including landings) etc complete all as specified and as directed

M&L for brick work with sub class 'B' brick, straight or curved on plan exc 6.0 mtr mean radius built in CM 1:6 etc complete all as specified and as directed

M&L ATT for treating the bottom and sides of excavation at the rate of 5 Ltrs of emulsion per sqr mtr of surface area complete all as specified and as directed

M&L ATT for treating the back fill in contract with foundation at the rate of 7.5 Ltrs of emulsion per Sqm of vertical surface (area of the sub structure in contact with back fill to be measured ) etc complete all as specified and as directed

M&L ATT for treating the top surface of filled up earth at the rate of 5 Ltrs of emulsion per square meter of surface complete all as specified and as directed

M&L ATT for treating the soil under plinth protection at the rate of 5 Lters of emulsion per square meter of surface complete all as specified and as directed

M&L ATT for treating the soil along with external perimeter of building at the rate of 2.25 Lters of emulsion per mtr of the wall etc complete all as specified and as directed

Spreading and levelling in well layers not exc 25 cm thick including watering as required etc complete all as specified and as directed

M&L for hard core of gauge not exc 63 mm, deposited, spread, and levelled in layers not exc 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed

M&L for cement concrete type C-1 (1:3:6) (20mm graded stone aggregates) 75 mm thick as in plinth protection etc complete all as specified and as directed

M&L for 75 mm thick cement concrete (1:4:8) type D-2 with using 40 mm graded stone aggregates) as in sub base of flooing etc complete all as specified and as directed

M&L for screed bed or bedding layer of mortar 20mm thick in CM 1:6 for laying floor finishes complete all as specified and as directed.

M&L for machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L for forming construction joint 30mm deep X 10 mm wide filled with sealing compound grade 'A' etc complete all as specified and as directed

M&L for Rendering 12mm thick in CM (1:4) on fair faces of brick work or concrete surfaces as backing coat of skirting etc complete all as specified and as directed

M&L for framed work as in grills, grating, railings etc with ends of bars shouldered and / or riveted or forged into spikes framed guard bars barred iron doors, ladders framed baluusters wals ways, railing framed wor of water tans and similar work etc complete all as specified and as directed

S&F 35mm thick flush shutter solid core construction with block board core and ply wood face panels, commercial type on both sides complete all as specified and as directed

S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed

S&F aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed

S&F 100 mm size butt hinges, heavy weight, cold rolled mild steel and fixed etc complete all as specified and as directed

S&F 150 mm long aluminium handle, cast type, anodised etc complete all as specified and as directed

S&F window section of frame 72x55 mm fixed to wall or concrete surface with rowl plugs made, of galvanized steel powder coated and section of shutter 47x20 mm ,mulion section 72x50 mm (Base steel as per IS 513 "D" quality galvanozed as per IS 277 with zinc of 120 gms/sqm.) glazed or gauged and wire gauge shutter prepare to receive wire mesh to the shutter(Double door shutter) with total coated thickness of 0.6 mm including grills/guard bars made of square bars powder coated fixed to windows frame with screws at 150mm c/c both ways, 4 to 5 mm thick sheet glass, 0.36mm stainless steel wire cloth with 1.40mm aperture necessory fittings and all builders hardware such as handles, tower bolts & stays etc. complete all as specified and as directed Make:- NCL type-4000 series.

M&L for rendering 5 mm thick in CM (1:3) on fair faces of brick work or concrete wall surface etc complete all as specified and as directed

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finished even and fair mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

M&L for rendering 15 mm thick in CM (1:6) on fair faces of brick work or concrete surface finsihed even and smooth (without using extra cement) etc complete all as specified and as directed

M&L for rendering 10 mm thick in CM (1:3) on fair faces of brick work or concrete surface mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

Supply only WPC

M&L for 3 mm thick APP modified prefabricated in five layers & weight not less than 3.6 Kg/Sq mtr water proof membrane reinforced with non-wooven polyster with two coat of aluminium paint over top surface of water proofing membrane with 15 cm longitudinal & horizontal over lapping and joints finally pasted with thermo- fused with LPG flames laid over a coat bitumen @ 1.20 Kg /Sqm over bituminous of primer 0.30 ltr per sqm as per manufacturer instruction of APP modified membrane etc complete all as specified and as directed

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick with soil etc complete all as specified and as directed

Removing excavated soil to a distance exc 250 mtr but not exceeding 500 mtr and depositing where directed etc complete all as specified and as directed

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed

M&L three coats of white wash on ceiling on new plastered surfaces including preparation of surfaces complete all as specified and as directed

M&L for preparing newely plastered surface of wall and applying two coat of cement base paint etc complete all as specified and as directed

M&L for preparing new plastered surface of walls and applying two coats of oli bound distemper over one coat of white wash complete all as specified and as directed

M&L for preparing new wooden surface of any description, not other wise described over 10 cm widht or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed

M&L for providing cement concrete (1:2:4) type B1 (using 20mm graded crushed stone aggregate) as in lintels upto 1.5M clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering , slightly rounded or chamfered angles and throating including form work complete all as specified and as directed.

S&F Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges , lock strike plate, etc, size of door frame 125x60mm complete all as specified and as directed by the Engineer in Charge.

M&L for PCC 1:3:6 type C-1 using 20 mm graded aggregate stone aggregate as in filling of pressed steel door frames and as in hold fast blocks incl all form work complete all as specified and as directed by the Engineer in Charge.

M&L for First quality, Non skid ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, laid in floors with neat cement slurry @ 3.00 kg/Square Metre over and laid over and including 15 mm thick screed bed of cement mortar (1:4) including pointing in white cement with pigment to match the shade of tiles, complete all as specified and as directed by Engineer in Charge.

M & L for first quality coloured glazed ceramic tiles, fixed in pattern of different colour including border of high lighter concept from make:- Somani/Kajaria/Johnsons or as approved by GE of size 300x 450 x 7mm thick as in vertical surfaces such as dado/skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles laid over and including 10 mm thick rendering in cement mortar (1:3), including pointing in white cement with pigment to match the shade of tiles, complete all as specified and as directed by Engineer in Charge. Note :- Pattern of the tiles shall be decided by GE at the time of execution.

S&F Rotational moulded polyethylene water storage tanks 500 Litres capacity 3 layer (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engineer in charge

S&F ball valves 20mm size high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed

S&F pillar tap 15mm size cast copper alloy chromium plated fancy type screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipes.

S&F brass chromium plated shower rose 125mm size swivel type complete all as specified and directed by Engineer in charge.

S&F bib taps cast copper alloy 15mm size chromium plated fancy type with crutch or butterfly handle screwed down , screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engineer in charge. \

S&F wash hand basins vitreous china flat back 550x400mm size white including CP waste grating 32mm size, PVC waste pipe 25mm bore heavy duty, chain and plug and porcelain stopper , brackets of MS angle 35x35x6mm size Note: Pillar tap shall be measured and paid for separately

S&F Wash down water closet squatt pan ‘Orissa Pattern’ white 580 x 440 mm size incl integral foot rest , PVC Flushing cistern 10 Liters capacity low level as specified, PVC waste pipe suitable to joint flushing cistern to water closet fixed on existing P or S trap complete all as specified and directed by Engineer in charge.

S&F Cast iron floor trap 75 mm bore including 100 mm round CP brass round grating including jointing to waste pipe in run lead and set in cement concrete 1:2:4 Type B1 complete all as specified and directed by Engineer in charge.

M&L for Cast iron soil waste and vent pipes 100mm bore size sand cast in any length with or without ears with cement joints laid in floors complete all as specified and directed by Engineer in charge.

M&L for Cast iron soil waste and vent pipes 75mm bore size sand cast in any length with or without ears with cement joints laid in floors complete all as specified and directed by Engineer in charge.

M&L for Cast iron soil waste and vent pipes 50mm bore size sand cast in any length with or without ears with cement joints fixed to walls complete all as specified and directed by Engineer in charge.

S&F Cast iron bends any radius 100mm bore size with Ducks foot or heel rest complete all as specified and directed by Engineer in charge.

S&F Cast iron bends any radius 75mm bore size with Ducks foot or heel rest complete all as specified and directed by Engineer in charge.

S&F Cast iron bends any radius, diminishing pieces or tapers 100mm bore size complete all as specified and directed by Engineer in charge.

S&F Cast iron bends any radius, diminishing pieces or tapers 75mm bore size complete all as specified and directed by Engineer in charge.

S&F Cast iron cowls 50mm size complete all as specified and directed by Engineer in charge.

M&L Extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joints , size of pipe 100mm complete all as specified and directed by Engineer in charge.

M&L Extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joints , size of pipe 75mm complete all as specified and directed by Engineer in charge.

S&F Salt glazed stone ware gulley traps 150x150mm size square mouthed type ‘P’ complete all as specified and directed by Engineer in charge.

M&L for Salt glazed stoneware drain pipes 150mm size laid in trenches and jointed complete all as specified and directed by Engineer in charge.

M&L for cement concrete 1:3:6 Type C2 using 40mm graded stone aggregate as in bed to drain pipes including packing under and haunching against the sides of pipes 150mm bore size after they are laid and tested complete all as specified and directed by Engineer in charge.

M&L for cement concrete 1:2:4 Type B2 using 40mm graded stone aggregate as in foundations of manholes etc complete all as specified and directed.

M&L for Pre cast cement concrete 1:2:4 Type B-1 using 20mm graded stone aggregate set in cement mortar 1:4 as in Manhole covers , shelves and similar items complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms moulds, mitred/ stopped ends etc complete all as specified and directed.

M&L for 25 mm thick Cement concrete 1:2:4 type B0 (12.5 mm graded aggregate) as in base of floor finish finished even and rough to receive floor bedding complete all as specified and as directed.

Cutting chases, pinning in brick walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels, etc; and cuttings chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exceeding 10 cm girth all as specified and directed.

S & F 15mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed. Note : Cutting chases as required shall be measured and paid seperately.

S & F 20mm dia tubes medium grade, galvanized, with all fittings such as sockets, bends, elbows, tees etc, concealed/surface fixed to walls and ceiling or laid in floors complete all as specified and directed. Note : Cutting chases as required shall be measured and paid seperately.

S & F 15mm bore concealed stop cock, regular body with adjustable wall flange , fancy type, chromium plated cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed all as specified and directed.

S&F 15mm bore angular stop cock with wall flange , fancy type cast copper alloy with capston head, chromium plated, screwed down high pressure and fixed for iron pipe with C.P. brass connection pipe with union nuts complete with C.P. brass flange including cutting and making good the walls where ever required.complete all as specified and as directed.

S & F gunmetal globe or gate valve with iron wheel head, screwed both ends for iron pipes 15mm bore complete all as specified and directed.

All as per Srl Item No.95 here in before but 20mm bore all as specified and directed.

S & F Vitreous China urinals,flat back large pastal colour complete including spreader and providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified.

M&L for providing precast cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) as in louvres and jallies, 40mm thick (measured solid), including all mouldings complete all as specified and directed.

M&L for sheet glass, 4mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed.

M&L for Damp proof course 40mm thick in PCC (1:2:4), type B0 (using 12.5mm graded crushed stone aggregate) with WPC (WPC shall be measured and paid separately) to horizontal or vertical surfaces including necessary formwork complete all as specified and as directed

Taking down old galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs complete all as specified and as directed.

Dismantling posts or struts of wood, steel or R.C.C any section, including taking out embedded portion in Concrete, brick work, ground masonry, etc. and making good disturbed portion complete all as specified and as directed.

Taking down cement plaster on brick walls & concrete surfaces & the like including raking out joints, hacking for key, scrubbing down with water etc., any description, including removal of rubbish outside MoD land, complete all as specified and as directed

Demolition of Brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework complete all as specified and as directed.

Removing excavated material (soil) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, soil complete all as specified and as directed.

M&L for providing plain cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and as directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in CM 1:4 on other than fair face of brick masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for preparation of old surfaces of walls by washing rubbing down and stopping of surface and applying one coats of cement base paint complete all as specified and as directed.

S&F mild steel angles, tees, flats, C section, MS square bars etc as in steel gates, steel posts and struts in fencing grills fixed to framed or indipendent members including embedding in concerete and screwing and welding wherever required etc. including cut to shape as directed, dirilling holes, notching notching for wire, etc including all necessary drilling, bolting welding or riveting and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Material and labour for preparation of old painted surfaces of steel of any description and girth, not otherwise described and treated with one coat of synthetic enamel paint complete all as specified and as directed.

S&F galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed. Note:- (Each line wire to be measured)

S&F hot dipped galvanised concertina razer tape coil 730mm dia, spring steel high tensile centre core wire 2.5mm dia having 200-250gm zinc coating, 0.5mm thick razer sheet having 90-120gm, zinc coating & 19 mm width (before wraping centre core wire), with GI clip 1.6mm thick including dismantling of old concertina coil complete all as specified and as directed.

M&L for 50mm thick cement concrete type B-1, (1:2:4) (using 20mm graded crushed stone aggregate) as in floors/ path etc finished cement concrete without using extra cement and spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismanling loose concrete cover of RCC columns, beams, slabs, chajjas and like as directed roughening and cleaning concrete surfaces with steel wire brushes, washed with water and allowed to dry including derustinig of steel reinforcement,providing fabric mild steel wire mesh 75x75x2mmdia as reinforcement to concrete surfaces, applying adhesive admixture over steel mesh and providing minimum 40mm thick ( average thickness) guinting mix using 1 part of ordinary Portland cement 53 grade and 2 part of ghager sand applied with the pressure of 2 to 2.5Kg per sqm by guinting machine and surfaces finished even and fair complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:3) on RCC Chajja / Facia over 20mm thick in CM 1:4 as dubbing coat etc complete all as specified and as directed.

M&L for rendering 10 mm thick in CM (1:4) on fair faces of brick work or concrete surface mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately.

M&L for Washed stone girth plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 Coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per sqm, top layer 15mm cement plaster WITH WHITE CEMENT 1:1/2 : 2 ( 1 White Cement : 1/2 coarse sand : 2 Marble stone chipping 10mm nominal size) inpanels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the marble stone chippings complete all as specified the groove shall be 15mm wide and 15mm deep in the top layer of washed stone girt plaster as per approved pattern using wooden battens, nailed to the under layer including removal to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specification and direction of the Engineer-in-Charge. Note:- Area includes in this items upto 4 stories of building, necessary scaffolding and arrengments are deemed to be included in the lum sum rates.

M&L for complete removal of existing treatment of wall/ceiling surfaces complete all as specified and as directed.

M&L for preparation of plastered or un plastered surfaces of walls/ceiling by applying 2mm thick birla white cement wall care putty to get smooth & levelled surface for applying next treatment complete all as specified and as directed.

M&L for preparation of plastered or un plastered surfaces of walls /ceiling etc and applying applying two coats of weather proof exterior emulsion paint complete all as specified and as directed.

M&L for preparing of old painted surfaces of wood & wood based surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed

M&L for preparation of old painted surfaces of steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed

E/M Works:- M&L for point wiring complete with stranded copper conductor 1.5 Sqmm size (Normal area) PVC insulated unsheathed FRLS Cable 1100 volts grade confirming to IS : 694 drawn in and including medium duty concealed PVC Conduit confirming to ISI marked not less than 20mm dia with concealed sunk -in pressed steel terminal boxes of required size not less than 1.2mm thick factory made and painted with stove enamelled black paint top cover 3.00 mm thick plastic laminated sheet of required colour fixed with brass screwes and cup washers including single core standed copper conductor 1.5 Sqmm PVC insulated unsheathed cable as earth wire to common earth and connected to earth dolly drawn in same concealed conduit complete all as specified for the following:-

One light point controlled by one switch with cables 1.5 Sqmm size all as specified and directed

One Fan Point/Exhaust fan controlled by one switch with cables 1.5 Sqmm size all as specified and as directed

One 5 Pin socket oulet 5/6 Amps on same board including single core straned copper conductor 1.5 Sqmm PVC insulated and unsheathed cable drawn in same conduit as earth wire to common earth and connecting to earth dolly all as specified

One 3 Pin socket outlet, 5 Amps, independent, with cables 1.5 Sqmm of size all as specified and directed

One light point controlled by Two 2-way switches, with cables 1.5 Sqmm size all as specified and directed

M&L for point wiring complete with stranded copper conductor 2.5 Sqm size (Normal area) PVC insulated unsheathed FRLS Cable 1100 volt grade confirming to IS: 694 drawn in and including medium grade concealed PVC conduit confirming to ISI marked not less than 25mm dia with concealed sunk-in pressed steel terminal boxes of requried size not less than 1.2mm thick factory made and painted with stove enamelled black paint top cover 3.00mm thick plastic laminated sheet of required colour fixed with brass screws and cup washeres including single core stranded copper condutor 2.5 Sqmm PVC insulated unsheathed cable as earth wire to common earth wire to common earth and connected to earth dolly drawn in same concealed conduit complete all as specified for one 2.5 pin socket outlet two in one 16/6 Amps on an independent board. Note: For item No 126 to 127 Rates shall deemed to be included for chases of conduit and sunking for boxes cutting and making holes in wall/floor for passing in or through conduit.

Supply and fix switch piano,flush type single pole, one way, 5 Amps, 240 volts ISI Marked Complete all as specified and directed at site

Supply and fix switch piano,flush type single pole, two way, 5 Amps, 240 volts ISI Marked Complete all as specified and directed at site

Supply and fix socket outlet 2 in 1, 3 pin 5 Amps Complete all as specified and directed at site.

Supply and fix switch socket combination 5 Amps/16 Amps, 5 in 1, flush type ISI Marked Complete all as specified and directed at site

Supply and fix ceiling roses, 3 terminal PVC/Polycarbonate, isolated body all as specified and directed at site.

Supply and fix stepped type electronic fan regulator flush type ISI Marked on the existing phenolic laminated sheet etc as required all as specified and directed at site.

Supply and fix of 20 wat (4ft long) MIRRORLITE LED decorative box type fitting with coloured end caps for LED tube and with one number 20 watt LED tube energy efficient alternative to T8/T12 fluorescent tubelights with same form factor and appearance suitable for 4 feet version etc complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable from ceiling rose to teriminal block and testing complete all as specified and directed at site

M&L for earthing complete with galvanized steel earth plate electrode 600x600x6mm thick burried directly in ground not less than 2.25mm deep below normal ground level (with top edge of the plate not less than 1.50m below the normal ground level) connected to GI earth wire 4mm by means of GI bolts, nuts, check nuts and washers of GI all as shown in electrical plate No , of SSR Part-I connected to earthing test point with and including necessary excavation and earth work in any strata PCC pit 1:3:6 type C-1, 20mm bore medium grade GI pipe for watering 15mm bore light grade pipe for GI wire protection and funnel including 40mm thick RCC salb cover and testing on completion all as specified and as directed

Supply and fix of LED building light luminaries 30 watt, pressure die cast aluminium housing with heat resistant toughened glass & IP66 protection complete all as specified and as directed.

M&L for of bracket made from GI pipe light grade 32mm bore bent to shape as required at site for street light fitting 1.2mtr in length and fixed on wall/pole including necessary MS clamps, nuts,bolt and washers including welding and painting complete all as specified and as directed

M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit /pipe or fixed to poles or any other indicated situation for loop earthing etc, as required 4mm dia galvanised iron or steel wire complete all as specified and as directed

Supply and fix MCB, DB, SPN4 way suitable for single phase 240 volts with 200 Amps rated bus bar, double door type suitable for mounting incoming and outgoing MCb,s single /double pole complete all as specified and directed at site

Supply and fix of MCB single pole 5-30 Amp 230 volts'B" series complete all as specified and as directed

Supply and fix of MCB single pole and neutral 40/63 Amps 230 volts "B' series complete all as specified and as directed at site

Supply and fixing ceiling fan 1200 mm sweep,240 volts AC supply, 50 Hz, with louvers and shutters including fixing on wall help of fasteners, drilling and making hole etc including making good the disturbed surface complete all as specified and as directed by Engr-in-Charge

Leo Network power systems

M/s GANJOO AND CO

Phogat Builders