REPAIR/MAINT OF INTERNAL ELECTRIC WIRING OF CERTAIN OFFICERS MD ACCNACCN IN AREA AT NASIRABAD AND REPAIR/MAINT OF CEILING FANS, EXHAUST FANS, WALL FANS AT AJMER AND NASIRABAD MIL STN UNDER GE NASIRABAD

Amount

M & L for attending and rectifying day to day complaints of fans by taking down celiing fan/exhaust fan/Wall fan of any type/make/sweep from its location at OTM, married accn and offices under GE Nasirabad, servicing of fans after removing blades, opening of ceiling fan at site and cleaning ball bearing,gun metal bush, filling grease /oil and changing of screwes, check nuts etc if required and re-assembling of fan, blades, down rod, canopy etc and hanging back fan to its original location after cleaning of body, and connecting up including providing sufficient length of twin core PVC flexible copper conductor wire of size 23/0.0076 from ceiling rose or connector to fan complete all as specified and directed by Engr-in-Charge with following Note below 1.01.

NOTE(All as per item No 1.00 above):- (a) The cost of collecting new/old ceiling/exhaust/wall fan any size and any make from AGE E/M store, assembling and fixing at site as directed including servicing, if required, is also deemed to be included in the above rate. (b) All T & P and labour team as required will be provided by the contractor as directed by Engr-in-charge. Cost of petty stores such as grease, lubricating oil, lock nut, cross pin,check nuts, insulation tape etc are deemed to be included in item No 1 (c) Rep of the contractor shall be present at complaint cell & responsible for attending the complaints from 8:30 am to 05:00 pm . (d) Cost of minor stores such as screws, insulation tapes ,nuts, bolts, split pins of required size etc shall be deemed to be included in the above quoted rate. However, major items such as bearings, bushes, holding clamps, canopies, fan blades etc shall be measured and paid separately under appropriate items of Schedule 'A'.

M & L for rewinding of stator complete with super enamelled copper wire (gauge/ weight of copper coil shall be same as per dismantled fans), including taping, quick varnishing, drying up, fixing connection leads and testing of the following size/ sweep of Fans complete all as specified and directed by Engr-in-Charge:- (Note : Rates are deemed to be inclusive for collection of fan from AGE E/M yard under contractor's own arrangement, removing defective parts, burnt winding carefully, cleaning & re-assembling the fan after repair i.e. oiling, greasing, washer, lock bolts, connector, cross pin etc, depositing back to AGE E/M yard and testing complete to the satisfaction of Engineer-in-charge (spare parts will be measured and paid seperately under relevant items).

All as per item No 2.00 above but for Ceiling Fan of 1400 mm sweep.

All as per item No 2.00 above but for Ceiling Fan of 1200 mm sweep.

All as per item No 2.00 above but for Exhaust Fan of 400 to 450 mm sweep.

All as per item No 2.00 above but for Exhaust Fan of 230 to 380 mm sweep.

Supply only (in replacement) following parts of fan complete all as specified and directed by Engr-in-Charge.:-

All as per item No 3.00 above but for Ball bearing of size 6201, 6202, 6203 (Make: NBC /SKF)

All as per item No 3.00 above but for Gun metal bush self lubricated, any size, suitable for ceiling and wall fan.

All as per item No 3.00 above but for Rubber reel for Ceiling Fan of 1200/1400 mm sweep.

All as per item No 3.00 above but for Clamp for hanging ceiling fan made out of MS heavy duty of size 40x 6 mm as per sample including nuts, bolts, washers, etc suitable for 40/50 mm dia GI pipe/angle iron.

All as per item No 3.00 above but for Holding clamps for ceiling fan with rubber reel, nuts, bolts, washers, split pins.

S & F in repairs PVC insulated flexible cable three core copper conductor of size 23/0.0076, ISI marked, complete all as specified and directed by Engr-in-Charge. (Note:-Other than for fans covered in item Sl. No. 01 above in which the rates are deemed to be inclusive.)

Supply only blade set suitable for Ceiling fan 1200mm/1400mm sweep matching with existing blades complete all as specified and directed by Engr-in-Charge.

Supply only exhaust fan blades of existing pattern for following sweep complete as per sample complete all as specified and directed by Engr-in-Charge:-

All as per item No 6.00 above but for 230 mm sweep exhaust fan.

All as per item No 6.00 above but for 300 mm sweep exhaust fan.

All as per item No 6.00 above but for 450 mm sweep exhaust fan.

Supply only table fan/wall fan blades as per existing pattern size 400 mm sweep complete as per sample complete all as specified and directed by Engr-in-Charge.

S & F in repair of condenser 2.5 MFD, 240 Volts, AC 50 Hz confirming to IS 1709 complete all as specified and directed by Engr-in-Charge. Make:- Epcos or equivalent as approved by AO.

S & F in repair of condenser 4.0 MFD, 240 Volts, AC 50 Hz confirming to IS 1709 complete all as specified and directed by Engr-in-Charge. Make:- Epcos or equivalent as approved by AO.

S & F in repairs of MS down rod 'medium grade' 15mm dia of following length in meter complete with making split holes, cut or threads at both end of pipe as required for hanging of ceiling fan incl. painting of rod with two coats of synthetic enamel white paint over one coat of primer complete all as specified and directed by Engr-in-Charge:-

All as per item No 10.00 above but of length 0.75 M complete all as specified and directed.

All as per item No 10.00 above but of length 1.50 M complete all as specified and directed.

All as per item No 10.00 above but of length 3.00 M complete all as specified and directed.

Fixing only of exhuast fan of size 300/450 mm sweep including making hole of appropriate size by cutting in the existing wall and making good and matching the distrubed surface wall with the existing wall, fixing with suitable size nuts, bolts, washers as required at site and connecting with and including suitable size and length of PVC insulated three core flexible three core copper conductor from ceiling rose complete all as specified and directed by Engr-in-Charge. Note:- Cost of collecting the exhaust fan from AGE E/M store, assembling and fixing is deemed to be included in the rate. complete all as specified and directed .

M & L for painting of ceiling/exhaust fan any type and size with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. and writing MES Number in black paint with skilled painter complete all as specified and directed by Engr-in-Charge. Note:- All T & P and labour team as required will be provided by the contractor and cost deemed to be included in the quoted rate. complete all as specified and directed.

S & F in repairs of modular fan regulator step type, 2 module (scocket) type, white in colour, complete all as specified and directed by Engr-in-Charge. Make:- Legrand Mylinc Series, Crabtree Athena Series, Hager insysta series.

Taking down carefully aluminium/copper point wiring (light,fan,socket or power) of any type complete including fittings and fixtures such as switches,ceiling roses, pendants, holders , sockets, light fittings, removing materials to store for keeping in safe custody or for taking credit and making good the disturbed surfaces of walls/ceiling/floor at various site etc, complete all as specified and directed by Engr-in-Charge.

Disconnecting of unserviceable sub main wiring of any size including conduit of any type and accessories & removing from site and making good the disturbed surfaces, complete all as specified and directed by Engr-in-Charge.

Disconnecting electric connections and taking down old unserviceable MCB DBs of any type including MCBs SPN/SP/TPN of any capacity, complete all as specified and directed by Engr-in-Charge.

Taking down carefully by unscrewing from boards / outlet boxes, light fittings and fixtures such as tube light fittings, bulk head fittings, mirror light, bldg sec light etc for re use at site or carrying to the store (To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed by Engr-in-Charge.

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed in and including non metallic rigid PVC concealed conduit 20 mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including one green colour cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Engr-in-Charge of following. Make of wire: KEI/HPL/Havells/Paraflex, Conduit: Anchor/National/Bajaj Plast/Polycab

All as per item No 18.00 above but One light point/bell point controlled by one way 5 Amps single pole switch.

All as per item No 18.00 above but One ceiling fan/exhaust fan point controlled by one way 5 Amps single pole switch.

All as per item No 18.00 above but One 5 pin 5 Amps socket outlet on same board with other switch.

All as per item No 18.00 above but One 5 Pin 5 Amps socket outlet on independent board with other switch.

All as per item No 18.00 above but One light point controlled by two, 2-way switches complete all as specified and directed.

All as per item No 18.04 above but with 2.5 Sqmm single core multi stranded PVC insulated unsheathed (FRLS) cable for 15 Amp socket outlet on independent board, complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed in and including PVC casing & caping with all PVC casing caping accessories and sunk type pressed steel anodised terminal box with bakelite laminated sheet top cover 3 mm thick, brass screws and cup washers including one green colour cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Engr-in-Charge of following. Make of wire: KEI/HPL/Havells/Paraflex, Conduit: Anchor/National/Bajaj Plast/Polycab

All as per item No 20.00 above but One light point/bell point controlled by one way 5 Amps single pole switch.

All as per item No 20.00 above but One ceiling fan/exhaust fan point controlled by one way 5 Amps single pole switch.

All as per item No 20.00 above but One 5 pin 5 Amps socket outlet on same board with other switch.

All as per item No 20.00 above but One 5 Pin 5 Amps socket outlet on independent board with other switch.

All as per item No 20.04 above but with 2.5 Sqmm single core multistranded unsheathed (FRLS) cable for 15 Amp socket outlet on independent board, complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type pressed steel modular terminal box and modular white cover plate with frame of suitable module as per site requirements for mounting of modular switches, sockets, fan regulator etc and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth for the following, complete all as specified and directed: Make of wire: KEI/HPL/Havells/Paraflex, Conduit: Anchor/National/Bajaj Plast/Polycab

All as per item No 22.00 above but One light point/bell point controlled by one way 5 Amps single pole switch complete all as specified and directed.

All as per item No 22.00 above but One ceiling fan/exhaust fan point controlled by one way 5 Amps single pole switch complete all as specified and directed.

All as per item No 22.00 above but One 5 pin 5 Amps socket outlet on same board with other switch complete all as specified and directed.

All as per item No 22.00 above but One 5 Pin 5 Amps socket outlet on independent board with other switch complete all as specified and directed.

All as per item No 22.00 above but One light point controlled by two, 2-way switches complete all as specified and directed.

All as per item No 22.04 above but with 2.5 Sqmm cross sectional area electric cable for 15 Amp socket outlet on independent board, complete all as specified and directed.

S & F of switch piano type, flush button single pole, one way 5 Amps, complete all as specified and directed. Make : Anchor / Legrand / Havells/Cona

S & F of switch piano flush type, 5 Amp , 240 volt , single pole, two way switch, complete all as specified and directed. Make : Anchor / Legrand / Havells/Cona

S & F of switch piano flush type 15 amps, single pole one way 240 volts complete all as specified and directed. Make : Anchor / Legrand / Havells/Cona

S & F of switch bell push, flush type, 5 Amp, complete all as specified and directed. Make : Anchor / Legrand / Havells/Cona

S & F of socket outlet 5 Amps, 5 Pin, flush type, complete all as specified and directed. Make : Anchor / Legrand / Havells/Cona

S & F of socket out let 2 in 1,multipurpose 3 pin 15/16 Amp flush type complete all, as specified & directed. Make : Anchor / Legrand / Havells/Cona

S & F stepped type ( switch type) electronic ceiling fan regulator flush type, AC, 230 volts , complete all as specified and directed. Make : Anchor / Legrand / Havells/Cona

S & F of modular switch 1 way 6/10Amp , 1 module, complete all as specified and directed. Make: Havells/Finolex/L&T

S & F of modular switch 1 way 16Amp, 1 module, complete all as specified and directed. Make: Havells/Finolex/L&T

S & F of modular switch 2 way 6 Amp, 1 module complete all as specfied and directed. Make: Havells/Finolex/L&T

S & F of modular bell push, 6 Amp, 1 module, complete all as specified and directed. Make: Havells/Finolex/L&T

S & F of modular socket 6 Amp, 2/3 pin combined 2 module complete all as specified and directed. Make: Havells/Finolex/L&T

S & F of modular socket 6 Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed. Make: Havells/Finolex/L&T

S & F modular stepped type ceiling fan regulator, 230 volt AC, 2 module, complete all as specified and directed. Make: Havells/Finolex/L&T

S & F of ceiling rose,surface type bakelite 65x17.5 mm, three terminals, complete all as specified and directed. Make : Anchor / Legrand / Havells / Cona

S & F of door bell electric, ding dong type, AC 230 volts, single phase , complete all as specified and directed. Make : Anchor / Legrand / Havells/Cona

S & F of lamp holder PVC/polycarbonate type with back plate complete all as specified and directed. Make : Anchor / Legrand / Havells/ Cona

S & F in repair LED tube light fitting in acrylic linear tube (1x 18 watt),230V for single LED tube light including 1 x 18 W LED retrofit bar professional CW 6500 K cover channel with Al. heat sink inside fixture, bipin holders,LED power driver, connector block, etc complete with all accessories internally prewired and including connecting up with three core flexible copper conductor cable with suitable size for connection of fitting from ceiling rose complete all as specified and directed. Make:Crompton Cat part No for batten DSGLT8-14, for tube rod LT8-20-865-2, Havells Cat part No for batten STREAKT8UPTO1X22WSSBSWH, for tube rod PHOTONULTRAE2.01213T8SSTL20WLED865SPC, or equivalent in Philips.

S & F wall mounted decorative luminarie fitting suitable up to 9/10 Watt LED lamp champagne gold finish fixture with plastic body suitable for B22 Base complete all as specified and directed by Engr-in-Charge. Make: Havells , Model- LHFOECE1TZ1O014, HSN Code: 9405 or equivalent model of Mepro/Philips

Fixing only serviceable light fitting any type and make obtained from sl item No 4 here-in-before complete all as directed.

S & F in repair LED mirror light fitting, 10 watt, 600 mm length complete with all accessories pre-wired and including connecting up with flexible copper conductor cable with suitable size complete all as specified and directed. Make: Havells/Crompton/Philips

S & F in repair LED light fittings, 10 W bulk head luminaries 230V, 50 Hz complete with all accessories and including connecting up with three core copper conductor cable with suitable size complete all as specified and directed. Make: Havells/Crompton/Philips

S & F in repair testing and commissioning energy saving street light luminaire 35/40 watt LED , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete, IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge. Make: Crompton Cat Part No TRP-400-35-57-SL-LM-NSR, Havells Cat Part No ENDCITYLITPLAT+SL35WLED757SASYBOPCWOSPD or equivalent in Philips.

S & F in repair recess mounted LED 12 watt Slim edge lit panel minimum lumen output 120 lumens/Watt, total system lumens 1440, compact, aluminum die cast housing, round fixture with opal diffuser and separate electronic driver complete all as specified and directed by Engr-in-Charge. Make Crompton Cat No LSCRM-12W-CDL, Havells Cat Part No INTEGRANEODLR12WLED857S or equivalent in Philips.

S & F in repair recess mounted 2' x 2' LED luminarie 36 watt, cool day/warm white light with white powder coated CRCA housing with LED driver, lumen efficacy >100 Lm/w complete all as specified and directed. Make Crompton/Philips/Havellls or equivalent.

S & F in repair surface mounted 2' x 2' LED luminarie 36/32 watt, cool day/warm white light with white powder coated CRCA housing with LED driver, system lumen efficacy >120 Lm/W, complete all as specified and directed. Make Philips/Crompton/Havells or equivalent.

S & F in repair surface mounted LED downlight 18 watt round shaped, Slim surface mounted LED panel with Al.die cast body with minimum system lumen efficacy >120 lumen/watt & total system lumens >2150 with premium diffuser to ensure glare free & even light distribution complete all as specified and directed. Make Crompton cat part no. LCDSPLN-R-18-CDL Havells, Model -Trim Cosmo Surface Round, Cat Part No LHEAAHP7IL1W018, or equivalent model of Philips

S & F in repair high efficiency round highbay with circular form factor and available in both Narrow & wide beam optics of IP lens/PC cover and luminaire in pressure die cast housing for industrial application 150 watt, system lumen efficacy >150 Lm/W Total System lumens 22500, 5700K IP66 protection including LED Potted driver complete all as specified and directed. Make Crompton/Havells/Bajaj

S & F in repair street light bracket made of 32 mm GI pipe, 1.2 mtr lenght fixed with two nos of clamp, nut and bolts complete all as specified and directed.

M & L for Submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 6 Sqmm multi stranded copper conductor cable drawn through and including 25 mm dia PVC non metallic rigid conduits and the conduits accessories incl one run of green colour earth continuity conductor with 6 Sqmm multi stranded copper conductor cable, in concealed conduit in wall/ roof/ ceiling, complete all as specified and directed. Note : - Two run of single core cable, one run of earth continuity conductor shall be measured as one unit length. Make of wire: KEI/HPL/Havells, Conduit: Anchor/National/Bajaj Plast/Polycab

M & L for Submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 6 Sqmm multi stranded copper conductor cable drawn through existing concealed conduit incl one run of green colour earth continuity conductor with 6 Sqmm multi stranded copper conductor cable complete all as specified and directed. Note : - Two run of single core cable, one run of earth continuity conductor shall be measured as one unit length. Make : KEI / Paraflex / Havells

S & F of MCB SP, 240 volt, 6 Amp to 32 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make : Havells/ Legrand/ Schneider

S & F of MCB SPN 10 to 40 Amp capacity, 10KA , 'C' curve complete all as specified and directed. Make :- Havells/ Legrand/ Schneider

S & F of MCB SPN 63 Amp capacity, 10 KA , 'C' curve complete all as specified and directed. Make : Havells/ Legrand/ Schneider

S & F of MCB TPN 63 Amp capacity,415 volt complete all as specified and directed. Make :Havells/ Legrand/ Schneider

S & F of MCB TPN 100 Amp capacity, 415 volt, complete all as specified and directed. Make : Havells/ Legrand/ Schneider

S & F MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door, IP-43, DB's made out of CRCA sheet steel enclosure, recessed type, factory made powder coated, 8 way, 240 volts suitable for housing MCB's and isolator's complete in all fixing material/accessories etc complete all as specified and directed. Note : MCB DB and MCB will be of same make. Make :- Havells/ Legrand/ Schneider

S & F MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door, IP-43, DB's made out of CRCA sheet steel enclosure, recessed type, factory made powder coated, 12 way, 240 volts suitable for housing MCB's and isolator's complete in all fixing material/accessories etc complete all as specified and directed. Note : MCB DB and MCB will be of same make. Make :- Havells/ Legrand/ Schneider

S & F MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door, IP-43, DB's made out of CRCA sheet steel enclosure, recessed type, factory made powder coated, 4 way, 240 volts suitable for housing MCB's and isolator's complete in all fixing material/accessories etc complete all as specified and directed. Note : MCB DB and MCB will be of same make. Make :- Havells/ Legrand/ Schneider

S & F of MCB distribution board triple pole & neutral IP-43 double door metal, 4 way ,415 volt made out of CRCA sheet steel , factory made powder coated with insulated bus bars , shrouded neutral bars, earth bars , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCB's complete all as specified and directed. MAKE: Havells/ Legrand/ Schneider Note: MCB DB and MCB SP/SPN will be of same make.

M & L for earthling complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to GI lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electric plate No 3 of SSR Part-I connected to continuous earth wire on main switch board all as specified or indicated and testing on completion including provision of earth wire protection by 15 mm dia medium grade GI pipe and watering pipe shall be 20 mm bore, medium grade including excavation & earth work in any type of soil & disposal of soi, providing alternate layers of charcoal and common salt, constr of PCC earth chamber in mix 1:3:6 type C-1 with 40mm thick RCC 1:2:4 type B-1 cover with handle made out oof 8mm dia bars, watering arrangement with funnel & wire mesh, complete all as specified and directed. Note. The unit rate includes for protection pipe and GI wire 4.00 mm from top of earth plate up to 7.5 meter above ground level.

S & F in repair single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole 20 Amp MCB SP `C' series for geyser & AC complete all as specified and directed. Make: Havells/ Legrand/ Schneider

KIRTIMAN TRADERS (BID ID -3304878)

M/s Shiv Builder and Suppliers (BID ID -3306307)

Sadhana Enterprises (BID ID -3308812)