Supply of various items at ITI nalwa

Wood Work Technician

Bevel Square 150 mm (i) Blade Material- Stainless Steel, Hardness- 418 HV to 460 HV (ii) Stock Material–Cast Iron, Fully Painted (iii) Wing Nut and Bolt Material: M.S. (iv) Measuring Range 0˚to180˚ (v) Approx.Weight-150Gram (vi) Operation-For testing any angle

Claw hammer 500 gram (i) Head made by heat treated steel, hardened upto 46 to 58 HRC with Curved Claw. (ii) Handle 300mmx30mm dia.Made by Hardwood(Rosewood) (iii) Operation-For Striking and Nailing

Hand Brush for cleaning 450mm (i) Bristle Material: Mexican Fibre, Sisal Fibre, Bristle length 70mm, Tampico Fibre, Fixingin Hardwood/ Plastic (ii) Operation-For workbench cleaning

Mallet Medium Size (i) Handle Size- Over all length- 385 mm, Toe side- 40mm(W), 25 mm(T), Heel side- 30 mm(W), 22 mm(T) (ii) Made by Hardwood (Rosewood) (iii) Operation- For Striking

Carpenter mortise gauge (i) Adjustable Spur Strip 300 X 8 X 8mm ±2mm, Made by Brass (ii) Fixed Spur Strip Size 20x8x8mm ±1mm (iii) Adjustment Thumbscrew Length15mm ±2mm, Dia. 15mm ±2mm and Shank 9mm ±2mm, Made by Brass (iv) Brass Pull side and thumbscrew to enhance in Gauge (v) Operation-For Marking along and across the grain for double line (Mortise)

Marking Knife (i) Overall length tip to handle end 200mm± 2mm (ii) Blade length 65mm ±5, Width-25mm ±2, Thickness- 4mm ± 1mm (iii) Tang Length-20mm, Thickness 4x4mm Square (iv) Blade material high carbon steel, Marking point sharp and 60 degree angle for accurate marking (v) Handle Length120mm ±5,diameter15mm ±2 and Gripping Point 10mm ±2mm (vi) Handle Made of Hardwood (Rosewood) (vii) Ferrule Length15mm, Dia.10mm,Material–M.S.Gauge 18SWG. (viii) Blade Hardness-60HRC (ix) Operation-For Marking

Mortise chisel (Set of 3 ) (i) Overall Length 250mm ±5mm (ii) Mortise Blade width 6mm, 10mm, 15mm, Thickness 15mm, Cutting edge angle30˚- 35˚,Neck to Cutting edge length150mm ±4mm, Tang Length 40mm ±2mm, Uppersize- 4x4mm, Lower 2 x 2mm ±1mm (iii) Blade Length 100mm ±3mm each. (iv) Handle Length120mm ±5mm, Handledia. 25-30mm ±2mm, Material Hardwood (Rosewood) (v) Ferrule size Length25mm,dia. 20mm,18 SWG. Material:M.S. (vi) Steel Hoop Dia.-20 ,Thickness-5mm ±1mm, Material:M.S. (vii) Blade material, High Carbon steel (viii) Blade Hardness 55–57 HRC (ix) Operation-For Chiselling

Electric Heater (i)1000/1500WattElement,StandDimensions(LxWxH)-250x250x85mm (ii) MadeofironHeatingPlateSize-200mm,HeatingPlateMaterial-ChinniMitti,NichromeWireWithSturdyTop Operation-For absorbing moisture ofwood

Twist drill bits (Set of 4 ) 6,8,10,12mm (i) Cuttingangle-30˚ (ii) Hardness:760 HRC to 900 HRC (iii) Material: High Speed Steel (iv) Operation-For Drilling

Cabinet scraper (i) Dimensions: Length-100mm (±1) Width-100mm (±1) Thickness-1mm Min. (ii) Material: Spring Steel (iii) Wooden Handle Size-110X30x20mm,Material:Hardwood(Rosewood),Fitted with rivet (iv) Operation-For Scrapping

Gauge chisel, Scribing (Set of 5 ) 6mm,10mm,12mm,16mm,20mm (i) Blade Material: High Carbon Steel (ii) Cutting angle: 25˚±5 ̊ (iii) Blade Hardness- 55 to 61 HRC (iv) Operation-For Scribing

Plumber

Item Name :-"V" Block Pair 7cm with clamp (i)size: Length 7cm, width 45mm, Height 45mm. (ii) Material: Hardened steel or cast iron (iii) V-Groove Angle: Generally 90 degree

Item Name :-"V" Block Pair 15cm with clamp (i) sizeLength: 15cm. width 75mm, Height 75mm (i) Material: Hardened steel or Cast iron (iii) V-Groove Angle:- Generally 90 degree

Item Name :-Bench Vice 150mm (i) Jaw width - 150mm ,Jaw opening capacity: 150-175 mm (ii) Jaw Depth-70-85mm (Iii) Material:- Cast iron body. (iv) weight: 15 - 20 kg (v) spindle :- Mild Steel (vi) Handle : Carbon steel or Alloy steel (vii) Thread Type: Acme thread (square thread) (viii Diameter: Around 20-25mm (ix) Length: 250mm to 300 mm

Item Name :- Metal-L 15cm (i)Type : Metal L square (ii) Size : Each arm of the L 15cm (150mm) width-20 mm (iii) Material : stainless steel or Carbon steel (iv) shape : 90° Angle between two Arms (V) Accuracy : 0.01mm (vi)Finish : Anti Rust Coating

Item Name :-Metal-L 30cm (i)Typ : Metal L square (ii) Size : Each arm of the L 30cm (300mm) width-30 mm (iii) Material: stainless steel or Carbon steel (iv) shape: 90° Angle between two Arms (V) Accuracy) : 0.01mm (vi)Finish : Anti Rust Coating

Item Name :-Angel plate 10cm x 20cm (i)size :-Height: 10cm,Length: 20cm,width: 10cm Thickness: 8mm to 15mn (ii) material :-Cast iron or hardened steel (i)) weight - 4 Kg.

Item Name :-File Card (i)Type :- wire brush and scraper edge (ii) size:- Length : 200mm to 300mm (iii)Brush Area: 100mm x 40 mm (iv) Brush Material :Hardened steel wire bristles. (v) Scraper Blade: Metal scraper (Vi) handle : Wood or Plastic

Item Name :-Hot Air Blower (i) Power Consumption: 1500 to 2000 watts. (ii) Voltage: 220-240V AC (iii) Temperature Range:- 100°C to 600 (iv) Air Flow Rate: - 200 to 500 Liters/misuute (V) Body Material:- Heat resistant Plastic with ergonomic handle (vi) Weight: 0.8 to 1.5 kg.

Item Name :-Box Spanner (i) Size Range :- 6mm to 25mm, 8 to 10 spanners in different sizes (ii) Material:- High grade carbon steel (iii) Design:-Double-ended tubular design Hexagonal openings at both ends. (iv) Length: -120mm to 200mm

Item Name :-Scraper flat 15cm (i)Blade Type: Flat, rectangular (ii) Length :- 150mm (iii) Blade Material:- carbon steel or stainless steel (iv) Blade width:- 25mm to 100mm (V) Blade Thicknes:- 1.5mm to 3 mm (Vi) Handle Material: -Plastic or wooden (vii) Edge Type:- Straight edge for scraping (Viii) Total Tool Length : - 150mm to 300mm

Item Name :-Scraper Triangalar 15cm (i)Blade Type: Triangular-shaped blade with Pointed Corners (ii) Blade Material :- Carbon Steel or stainless steel (iii) Length:-150mm (iv) Blade Thicknes: - 2mm to 4mm (v) Handle Material: -Plastic or wooden (vi) Blade size:- Each side ranges from 40mm to 80 mm (vii) Edge Type:- Sharp or beveled edge (viii) Total Tool Length: - 200mm to 300mm

Item Name :-Scraper Half Round 15cm (i)Blade type :- Half round (curved Blade) (ii)Blade Length :- 150mm. (iii) Blade Material:- Carbon steel or stainless steel (iV) Blade width: 20 mm to 40mm (v) Blade Thickness: 2mm to 4mm (vi) Handle material: Plastic or wooden (vii) edge Type - Sharpened curved edge. (viii) Total Tool Length: 250mm to 300mm

Item Name :-Chisel Cold flat 3/4"x18" (i)Type:- Cold flat chisel (ii) Length :- 18 " /450mm (iii) Material:- High Carbon Steel (iv) Shankshape:- octagonal (v) Weight :- 1 kg to 1.5kg

Item Name :-Chisel Cold Pointed 3/4"x18" (i)Type:- Cold Pointed chisel (ii) Tip Type :- Tapered Painted tip (iii)) Tip diameter : - 3/4 " /19mm. (iv) Length :- 18"/450mm (v) Material:- High Carbon Steel (vi) Shankshape- octagonal (vii) Weight - 1 kg to 1.5kg

Item Name :-PPR Pipe Cutter (i)Type:-Hand-operated pipe Cutter (ii) cutting Capacity - 20mm to 40 mm (iii) Blade Material - High Carbon steel or stainless Steel (iv) Body Material - Aluminum alloy (ⅴ) Handle :- Heavy duty Plastic Handle

Item Name :-Chain Pipe vice (i)Type:- chain type vice (ii) Jaw Capacity:- up to 150mm out diameter (iii) Body Material:- Cast iron. (iv) Jaw Material:- Hardened steel Jaw (v) Chain Material:- Heavy-duty Steel chain

Item Name :-Tubular Spanner (i)Type:- Tubular Box spanner (Double-ended) (ii) size:- 20mmx22mm, 21mmx23mm (iii) Material :- High grade Carbon steel (iv) Length :- 150mm to 250mm (v) Design: - Hollow cylindrical shape

Item Name :-Allen Key (set per 10 piece) (i)Type:- Allen key (ii) Material:- Alloy steel (iii) Key Type:- L-shaped or T-handle (iv) Size:- 1.5mm, 2mm, 2.5mm, 3mm, 4mm, 5mm, 6mm, 8mm, 9mm and l0mm.

Item Name :-TDS Meter (i)Product Name:- Digital TDS meter (ii) Measurment Range: - 0-9999 PPM (iii) Display: - Digital LCD Screen (iv) Casing:- Plastic Body with Protective cap

Item Name :-SINK Auger (i) Length :-01 meter (ii) Cable Diameta :- 6mm (iii) Cable material :- High tensile steel (iv) Handle Type:- Plastic or rubber grip (v) Drum:- Plastic or metal housing to store the Cable

Fitter

Caliper inside spring Type ,150mm (i). Legs: Carbon and alloy tool steel. (ii) Spring: Carbon spring steel. (iii) Fulcrum roller, Adjusting Screw and Nut Hardness: 400-500 HV. (iv) Measuring Tip Hardness: 650HV (±50HV)

Caliper outside spring joint,150 mm (i) Legs:- Carbon and alloy tools steel. (ii) Spring:- Carbon spring steel. (iii) Fulcrum roller, Adjusting Screw and Nut Hardness:-400-500HV. (iv) Measuring Tip Hardness:-650HV(±50HV)

Caliper Hermophrodite spring Type,150mm (i). Legs Carbon and alloy tool steel. (ii). Carbon spring steel. (iii). Hardened and tempered as per IS 4052 : 1983 (iv). Measuring Tip Hardness: -650 HRC (±50 HV) (v). Fulcrum roller, Adjusting Screw and Nut Hardness: - 400,-500 HV (vi). With fine adjustable screw

Divider Spring Type,150mm (i). Measuring length 0-150 mm (ii). . Legs made of Mild steel. (iii). Hardened and tempered. (iv). With fine adjustable screw. (v). Material of Divider Shall be Rolled, drawn or cast brass or stainless steel Measuring Tip Hardness: -650 HV (±50 HV) (vi). Fulcrum roller, Adjusting Screwand Nut Hardness: -400, -500 HV. (vii). Nominal Size (l) 150mm (viii). Max.Measuring 150mm (ix). Capacity 150mm (x). Dia of Nominal(d) 7 mm (xi). Fulcrum Dia(h) 20mm (xii).TipThickness(s) 3 mm (xiii). TipWidth(w) 9.5 mm

Hammer Ball Peen with Handle,450 grams (1LB) (i). Head Material: High-carbon steel(Drop Forged) (ii). Handle material: Tough Wood Rosewood/Ash wood/Teakwood, Finished & Polished. (iii). Head and Peen Hardness: 46-58 HRC (iv). Nominal Mass Weight)-500(g) in gram. (v). Head Length(A) -105 mm (vi). CheekWidth(B)- 40 mm (vii) Cheek Thickness(C) - 32 mm (viii) FaceDia(D)-30 (ix) BallPeenDia (G) -25 mm (x ) Cheek to Face Length(M) - 60 mm (xi) Poll Length(N) -22mm (xii) Handle Length (Approx.) -300mm

File Flat -2nd Cut (i). Body Length- 250 mm (minimum) (ii). Tang Length (TL) – 60 mm (minimum) (iii). Width –25 mm (minimum) (iv). Thickness – 5 mm (minimum) (v). No. of Upcut / Inch : 28 (minimum) (vi). Upcut inclination: 65°(±1°) (vii). No. of Overcut/Inch: 24 (minimum) (viii). Overcut Inclination : 45°(±1°) (ix). No. of Edge cut/Inch : 32 (minimum) (x). Edge cut Inclination : 90°(±1°) (xi). Hardness: 62 HRC (minimum) (xii). Rake Angle -10°(±2°) (xiii). Material - High Carbon Steel

File flat Smooth (i). Body Length -250 mm (ii). Tang length (TL) – 70 mm (iii). Width (W) - 25 mm minimum. (iv). Thickness (T) - 5.5 mm minimum. (v). No. of Upcut / Inch : 25 (minimum) (vi). Upcut inclination: 65°(±1°) (vii). No. of Overcut/Inch: 19 (minimum) (viii). Overcut Inclination : 45°(±1°) (ix). Edge cut Inclination : 90°(±1°) (x). Hardness: 62 HRC (minimum) (xi). Rake Angle -10°(±2°)

File Half round 2nd cut,150mm (i). Body Length (L) -150mm(Min.) (ii). Tang Length (TL) - 50mm(Min.) (iii). Width (W) - 16mm(Min.) (iv). Thickness (T)- 4mm(Min.) (v). No.of Up cut/Inch -(38-39F/S)/ (36-37 R/S) (vi). Up cut inclination - 65°(±1°) (vii). No. of Over cut/ Inch- (36-36F/S)/(32-33 R/S) (viii). Over cut Inclination -50°(±1°) (ix). No.of Edge cut/Inch - 37.5(Min.) (x). Edge cut Inclination 65°(±1°) (xi). Hardness 62 HRC (Min) (xii). Rake Angle -10°(+2°)

Dot Punch,100mm (i). Over all Length: 100mm.(Min.) (ii). Body Dia: 8mm.(Min.) (iii). Tip Dia: 4mm. (iv). Taper Length: 22.50mm.(approx.) (v). Tape red point Angle: 60° (vi). Material: High carbon steel (vii). Knurled Body for grip (viii). Point Hardness: 52-58 HRC (ix). Head/Face Hardness: 38-46 HRC

Computer/IT Items

Crimping Tool,RJ 45 (i). Suitable for Cat5, Cat 6 and Cat 5e cable (ii). Punch down tool, High quality Wire stripper (iii). Suitable for network cable with RJ45 Connector and RJ Connector (iv). The jaw of the press-pliers is made of high quality steel.

Punching Tool,For Punching RJ-45 Socket with Cable (i) Punch down tool to cut and terminate cable (ii) Keystore jack compatiable for cat-3,cat-5,cat-5e,cat-6 and 6 A (iii) Blade item :- OPT - BL110 (iv) Blade Material :- Carbon steel

Mini Dongle for Bluetooth device Connection,USB (i) Connection:- USB 2.0/3.0 (ii) Compatible Device : - Laptop , Desktop (iii)Connectivity Range :- upto 10 meter(with no obstacles interferencs ) (iv) Data link protocol: - USB , Bluetooth (v) Hardware Interface :- Bluetooth 5.0 (min.) (vi) Wireless speed: - 300mbps for HD video/voice (vii)OS support :- Window 7/8.1/10/11 (for Desktop, laptop) (viii) Advanced security :- WPA/WPA2 encryption standard

Head Phone Mike Set,wired (i) Wired over ear Headphone with mic (ii) Head band:-Foldable and adjustable (iii)Powerful bass and clear treble sounds (iv)Impedance: 32 ohm (v) Buttons: Volume/ mute control, Inbuilt noise cancelling mic (vi) Frequency Response: 20Hz to 20KHz (vii) Connector Type: Cable upto 4 feet (viii) Sensitivity: 110 db to 115 db

Electrician

Measuring Steel Tape (i). Length–5 meter (ii). Material Stainless Steel at least 3 mm thick which are sufficiently durable & stable (iii). Blade width-19mm (Min.). (iv). Blade graduated both in metric and English unit. (v). Case Material–Plastic. (vi).WithThumb lock, Belt clip and Hook facility.

Smoothing cutters (i). Size: 50 mm X 200mm (ii). Material of Frame: Wooden(body) (iii). High Grade Cast Iron Construction Ribbed For Rigidity. (iv). Blade Matrial: Carbon Steel Cutting Iron Hardened And Tempered For Long Lasting Sharp Cutting Edge (v). Precise Blade Adjustment (vi.) Comfortable Hardwood Handle And Knob

De soldering Gun. (i).Heat proof nozzle, (ii). Body - PVC type, (iii). Nozzle size - 250mm, (iv). Heating output 80W, (v). Nozzle size outer dia 2.5mm ,inner dia 1.2mm

Contactor & auxiliary contacts (i.) 3 phase (ii.) operating voltage - 415 Volt (iii.) Rating - 25 Amp with 2 NO and 2 NC Auxilary Contacts (iv.) Brass contacts. (v.) In Bakelite case (vi.) Relay Coil Material –Copper

Limit Switch i. Liver operated ii. 2A,500v iii. 2- contact Configuration - (2 NO, 2 NC) (iv.) Operating Force : 150g max (v). Release Force : 40g max (vi.) Type: Rotary Adjustable Liver Arm with Roller (vii.) Fixing Thread Diameter: 4mm (viii.) Roller Dimension: 1.8 x 0.7cm (ix.) Lever Arm Length: 4.6cm (x.) Overall Size: 12.3 x 2.8 x 3.9cm(LxWxH)

Reverse current (i). Operating voltage 440 volt, 16 amp. (Ii). Frequency - 50Hz (iii). In Bakelite case.

Thermometer Digital (i.) Digital Type (ii). Measurement Range: 32°C (89.6°F) ----- 42°C (107.6°F) (iii). Low Temperature Display: Temperature < 32°C (89.6°F) Display L°C(L°F) (iv). High Temperature Display: Temperature > 43°C (109.4°F) Display H°C(H°F) (v). Accuracy: 35°C (95°F) ----- 39°C (102.2°F) ±0.1°C (0.2°F) (vi). Display Resolution: 0.1°C (0.1

Various Lamp :- (A) Halogen Lamp 250W (i). Operated voltage 230 volt (ii). Frequency 50 HZ (iii). with halogen rod 200 watt (iv). choke and all other accessories in bakelite or iron case

(C) High-pressure sodium Lamp 250W ( Complete set With Copper Choke, Ignitor, Holder etc.) All Accessories in Bakelite or iron case.

(C) High-pressure sodium Lamp 250W ( Complete set With Copper Choke, Ignitor, Holder etc.) All Accessories in Bakelite or iron case.

(D) Low-pressure sodium Lamp 180W ( Complete set With Copper Choke, Ignitor, Holder etc .) All Accessories in Bakelite or iron case.

Bus bar with brackets (i). Bus bar length 1 mtr. (ii). operated voltage 415V (iii). Current rating 200 Amp. (iv). Frequency 50 HZ (v). Bus Bar Material : Copper (vi). Bracket Material : Stainless Steel

Rubber mat (i). 4’(L) X 2’(W)X 1”(T). (ii). Material :Elastomer (iii). Anti slip (iv.) Colour : Black (v). Insulation Resistance with water: 100000 MΩ with 5000 V Megger(Min.)

RCC Pole with accessories (MS angle iron, ‘C’ clamp, stay insulator etc.) and materials (i). Pole Material : Reinforced Cement Concrete (RCC) (ii). Pole Length : 6 Mtr (4"X4"Top 4"X8"Bottom)

Lux meter (i). LCD read out (ii). 0.05 to 7000 lumens (iii). Display -3½ digit , (iv). 18 mm (0.7") LCD , (v). Display in Lux (vi). Accuracy - + (5% rdg. +2 dgts ) , (vii). Over -Range - Indication of "I" , (viii). Sampling Time - 0.4 second , (ix). Operating Temperature - 0° to 50 °(32° to 122° F ) , (x). Data Hold switch (xi). Temperature Characteristic - + 0.1% / °C Repeatability - + 2% (xii) Silicon photo diode with filter , (xiii) Low Battery Indication - (- + ) (xiv) Power Supply - 9V battery (6F 22 ) , (xv) Accessories - Instruction Manual , arraying Case.

Immersion Heater (i). Rated power 1500 Watt (ii). Operated voltage 230V (iii). Frequency 50hz (iv). Single phase .

Mixture & Grinder (i). Rated power 750 W (ii). Operated voltage 230 Volt, AC supply (iii). Armature and Field winding in copper (iv). 3 stainless steel jar, of size 0.5 – 2.0 ltr. (v). Speed 15000 rpm

Scissors blade (i). Overall Length - 200mm (ii). sharp/blunt blades of stainless steel (iii). riveted with a screw in stainless steel (iv). rust proof metal securing the two blades. (v). The handle is of sturdy plastic which enables a good grip

Crimping Tool 1.5 sq. mm - 16 sq. mm & 16 sq. mm - 95 sq.mm (i). 1.5 sq mm to 16 sq mm & 16 sq. mm - 95 sq.mm. (ii). Made up of forged alloy steel. (iii). PVC insulated handle. (iv). Material of die – Tool Steel. (v). Operating type manual operated.

Pin Type, shackle type, egg type & suspension type insulators Including hardware fitting i. Pin type insulators including hardware fitting: 11kv Capacity, ii. Material – Porcelain. iii. Shank Diameter 20mm (iv.) Collar Diameter 40mm v. Collar thickness 5mm (vi.) It should be connected with horizontal as well as vertical position.

(Shakle type) (i). Shackle type insulators including hardware fitting: 11kv capacity, (ii). Material –Porcelain. (iii). Size of insulator 90x75 mm (iv). Mechanical failing load 11.5 KN (v). Dry P.F withstand voltage KV(rms) 23 (vi). wet P.F withstand voltage KV(rms) 10 (vii). P.F Puncture withstand voltage KV(rms) 1.3x actual dry flash over voltage (viii). In distribution line, metallic strip is used to connect the shackle insulator

Egg type (i). Egg type insulators including hardware fitting: 11kv capacity, (ii). Material – Porcelain/Ceramic (iii). Size in mm 90x75(LxW) (iv). Shape - Egg type

Suspension type (i). Suspension type insulators including hardware fitting: 11kv capacity, (ii). material - porcelain. (iii). The multiple discs can be used based on voltage level (low to high). (iv.) Rated voltage 11 kv v. Section length 297mm (vi.) Dry arcing distance 165 mm (vii.) Kreeping distance 300 mm (viii.) specified mechanical load tension 70 KN (i(x.)) power frequency wet withstand voltage 40 kv

(A) Cut Out Relay (i.) Input Voltage 4-32 volt DC, 4 ma, (ii). Output Voltage AC 24-440 volt ,16 amp. (iii). In Bakelite case (iv.) In copper winding and brass terminal.

(B) Over current Relay (i). Operating voltage 440 volt,16 amp. (ii). Frequency - 50Hz (iii). In Bakelite case (iv.) operated voltage 440V

(C) Under voltage Relay (i). Operating voltage 440V, 16 amp (ii). Frequency - 50Hz (iii). In Bakelite case

Temperature controlled Soldering Iron (i). Power - 50 Watt (ii). 230 Volt with copper bit and bit holder (iii). ESD safe station iron (iv.) heat - resistant silicon cable - A1321 Element 900M Series type.

Earth Electrode (i).Primary & secondary Electrode (ii). Primary Electrode 2100mm(length)x28mm(width)x3.25mm(thickness) of copper (iii). Secondary Electrode Cu Strip 20mmx5mm of copper (iv.) Hole size 11 mm.

Pully Puller with 3 legs (i). made up of High carbon steel (ii). Nominal Size - 300 mm (iii). Spindle Material - Mild Steel (iv). Spindle Thread Type - V (v). No. of Legs - 3 (movable) (vi). Material of Legs - Drop forged Steel

Drill hand brace (i). Drll chuck with holder length - 100 mm (ii). Jaw Size: 13mm (iii). Drill Chuck Type: 4-jaw chuck with 3-position ratchet (iv). Drill Chuck Size: 10mm round chuck (v). Plastic handles with 280mm sweep (vi). For precision wood drilling (vii). Dimension- 300mm x 180mm x 65mm(LxWxH) (viii). Shank Type- Brace (ix). Material- Stainless Steel (x). Plastic handles with 180 mm sweep (xi). For precision wood drilling

Plane cutters (i). Size: 50 mm X 200mm (ii). Material: Cast Iron(Body) (iii). High Grade Cast Iron Construction Ribbed For Rigidity. (iv). Blade Material: Carbon Steel Cutting Iron Hardened And Tempered For A Long Lasting Sharp Cutting Edge (v). Precise Blade Adjustment (vi). Comfortable Hardwood Handle and Knob.

File half round ( i). Body Length- 200 mm (minimum) (ii). Tang Length (TL) – 60 mm (minimum) (iii). Width –20 mm (minimum) (iv). Thickness – 5.5 mm (minimum) (v). No. of Upcut / Inch : (38-39 F/S)/(36-37 R/S) (vi). Upcut inclination: 65°(±1°) (vii). No. of Overcut/Inch: (36-36 F/S)/(32-33 R/S) (viii). Overcut Inclination : 50°(±1°) (ix). No. of Edge cut/Inch : 37.5 (minimum) (x). Edge cut Inclination : 65°(±1°) (xi). Hardness: 62 HRC (minimum) (xii). Rake Angle -10°(±2°) (xiii). Material - High Carbon Steel

File flat bastard (i). Body Length -250 mm (ii). Tang length (TL) – 70 mm (iii). Width (W) - 25 mm minimum. (iv). Thickness (T) - 5.5 mm minimum. (v). No. of Upcut / Inch : 25 (minimum) (vi). Upcut inclination: 65°(±1°) (vii). No. of Overcut/Inch: 19 (minimum) (viii). Overcut Inclination : 45°(±1°) (ix). Edge cut Inclination : 90°(±1°) (x). Hardness: 62 HRC (minimum) (xi). Rake Angle -10°(±2°)

Contactor & auxiliary contacts. (i). 3 phase (ii). Operating voltage - 415 volt (iii). Relay current 32 Amp with 2 NO and 2 NC auxiliary contact. (iv). In Bakelite case (v). Relay Coil Material –Copper

Laboratory Type Induction Coil (i). Power Norms - 1000 W with 10mm spark, (ii). Brass electrode (iii). In wooden case (iv). With 9 volt battery (v). Induction coil 9 volt dc made from copper wire (vi). Operated voltage 3-9 volt dc

Milli Voltmeter centre zero analog, portable box type (i) . housed in Bakelite casei. DC voltage 100 – 0 – 100 mV (ii). in Bakelite case (iii). Freq. 50hz (iv). Analog type (v). moving coil type (vi). Size: 208mm X 98mm X 180 mm (vii). Type - portable box type

AC Ammeter MI, analog, portable box type housed in Bakelite case (i). 0 - 1 A, 0-5 A, 0-25 A (ii). Size : 208mm X 98mm X 180 mm (iii). Type : Analog Display (iv). potable box type (v). Moving iron type (vi). In Bakelite case

Magnetic Flux Meter (i). Technical Specifications : (ii). Range : 0-500 tesla (iii). Accuracy : ± 0.5% (iv). Display : 3 ½ digit 7 seg. (v). Detector : Hall probe with an imported hall element (vi). Frequency 50 Hz (vii). Special : Indicate the direction of the magnetic field (viii). Digital Type

3- point D.C. Starter (i). For 2.5 KW DC motor (ii). With NO volt coil & Over load protaction (iii). With brass contacts (iv). Carrying handle (v). BTI-30 Terminal should be provided for power supply, motorconnections should be brought out in front of starter.

Bearing Puller (Inside and Outside) (i). Nominal size - 200mm (ii). Hardness of Legs – 35 HRC (minimum) (iii). Hardness of Housing – 30 HRC (minimum) (iv). Hardness of Central Bolt – 35 HRC (minimum) at threads & 45 HRC (minimum) at Tip. (v). Hardness of Link Plate – 30 HRC (minimum) (vi). Made up of High carbon steel (vii). Spindle Material - Mild Steel (viii). Spindle Thread Type - V (ix). No. of Legs - 3 (movable) (x). Materialof Legs - Drop forged Steel (xi). All parts plated with zinc or chromium

File Flat -2nd Cut (i). Body Length- 200 mm (minimum) (ii). Tang Length (TL) – 60 mm (minimum) (iii).Width –20 mm (minimum) (iv). Thickness – 5.5 mm (minimum) (v). No. of Upcut / Inch : 28 (minimum) (vi). Upcut inclination: 65°(±1°) (vii). No. of Overcut/Inch: 24 (minimum) (viii). Overcut Inclination : 45°(±1°) (ix). No. of Edge cut/Inch : 32 (minimum) (x). Edge cut Inclination : 90°(±1°) (xi). Hardness: 62 HRC (minimum) (xii). Rake Angle -10°(±2°) (xiii). Material - High Carbon Steel

Rheostat (Sliding type) 0-25 ohm 2amp, 0-1 ohm 10 amp,0-300 ohm 2amp,0-10 ohm 5 amp (i). Contact :Laminated Phosphor Bronze strip or copper graphite. (ii). Contact Block :Brass or Aluminum. (iii). End bands :Brass. (iv). Former: Non-inductive, Non-magnetic, Non-porous full baked porcelain or glazed ceramic. (v). Guide rod: Brass. (vi). Supports :Cast iron or aluminum die casted. (vii). Terminals: Brass or brass embedded with insulating materials such as Bakelite. (vii)i. Terminals screws :Brass (ix). Wire : Constant or nichrome.

Ohm Meter; Series Type & Shunt Type, portable box type Ohm Meter; Series Type portable box type (i) 0-50 ohm analog type (ii) Material Bakelite case, (iii) Display Size 85X95mm (min.) (iv) Dimensions – 140(L) X105(W) X90(H) mm. (min.) (v) Accuracy +0.25, -0.25. (vi) With 1.5V battery

Ammeter MC analog, portable box type housed in Bakelite case (i) Rating : 0 - 500 mA, 0-5 A, 0-25 A, (ii) In Bakelite case with holding strap (iii) Size : 96mm X96mm X55mm (iv) Type : Analog Display (v) Potable box type (vi) Moving coil type (vii) Brass Terminals

Digital Wattmeter (i) Supply voltage 230 volt (ii) Power rating1 KW (iii) Frequency 50hz (iv) Technical Specifications :- (v) Input Voltage : 10-300V (vi) Input Current : 0.01 to1 A / 0.05 to 5A / 0.1 to 10A (vii) Accuracy : Class 0.5 (viii) Resolution : Floating Decimal Point (xi) Panel Dimensions : 96 X 96 X 85 mm (LxWxH) (x) In Bakelite case

A.C. Energy Meter (i) Input voltage 230 volt, Single Phase, 50 Hz (ii) Rated current 10 A (iii) Body material – Plastic (iv) Terminal Box – 2 input and 2 output brass terminal. (v) induction type (vi) Indication of KWH consumption. (vii) Capable of energy record.

A.C. Energy Meter (i) Input voltage 440 volt, 3 Phase, 50 Hz (ii) Rated current 15 A (iii) Body material – Plastic (iv) Terminal Box – 3 input and 3 output brass terminal. (v) induction type (vi) Indication of KWH consumption. (vii) Capable of energy record.

Power Factor Meter Digital (i) Operating Voltage 440 V, 3 phase AC. (ii) Current Capacity20 A (iii) portable box type (iv) Size : 208mm X 98mm X 180 mm (v) In Bakelite case (vi) Brass Terminal (vii) Display - four digit

Scissors blade 150mm (i) sharp/blunt blades of stainless steel (ii) 27.4 riveted with a screw in stainless steel (iii) Rust proof metal securing the two blades. (iv) The handle is of sturdy plastic which enables a good grip

Earth Plate A. Earth plate Copper (i) 60cm X 60cm X 3.15mm Copper Plate (ii) Length – 600 mm. (iii) Breadth – 600 m. (iv) Thickness – 3.15 mm. (v) Material – Copper.

B. Earth GI Plate (i) 60cm X 60cm X 6mm GI Plate (ii) Length – 600mm (iii) Breadth – 600mm (iv) Thickness – 6mm (v) Material – Galvanized Iron.

Ammeter 300A/ 60A DC with external shunt (i) Rating Range : 0 - 300 A, DC & 0-60A DC (ii) Size : 220mm X190 mm fixed in wooden box (iii) Type: Analog Display (iv) Material – Bakelite (v) Brass Terminals

Drift, copper 10 x 15 1/2 mm (i) Material -Copper (ii) Lengths – 150 mm (iii) Shape - round 0.5 mm

Hollow Punch set of seven pieces 6mm to 15mm (i). Length 100-150mm (ii). Diameter 6-15mm (iii). Seven pieces set (6, 7, 8, 10, 12, 14,15 mm) (iv). Straight shank (v). Body knurling (vi). Material- high carbon steel/ High Speed Steel

Piston Ring groove cleaner (i). Length of beam-300+100=400 mm (ii). Thickness of beam-5 mm (iii). Width of beam - 20 mm (iv). Material - High carbon steel (v). Thickness of grove cleaner blade -2 mm

Prick Punch 15 cm (i). Diameter 6 mm, Length 150 mm. (ii). Tip angle: - 60°. (iii). Material:- High carbon steel Knurled Body for grip Point (iv). Finishing:- Polished finish. (v). Others:- Precision centered tip for accuracy

Hand Shear Universal 250mm Hand Shear should be made from high carbon steel or tool steel like : 80 of schedule II and T80Mn65 of schedule Vi of IS : 1570-1961 with a maximum sculpture and phosphorus content of 0.05 percent each.

Spanner Clyburn 15 cm (i) Item length- 150 mm (ii)Material- Alloy Steel (iii) weight -160 gm (iv) Type- Open End Wrench, Single Sided (v) Jaw Opening - 0-18mm (vi) Adjustable with worm & worm pin.

Stud Remover With Socket handle (i). Material: Steel (ii). Size - 1/4" to 1/2" (iii). 1/2" Stud Puller comes with 1/2" Square Drive L Socket (iv). Handle 6" inch Length..

Straight edge gauge 4 feet i). Straight edge gauge size- (ii). Overall (L1)-1230mm minimum. (iii). Length (L)-1219.2mm. (iv). Width (W)-50 mm±1 mm. (v). Height (H)-5 mm ±0.5 mm. (vi). Straightness-0.03mm (vii). Made of Stainless steel/ alloy steel (viii). Measuring system –Metric and British (ix). Measuring least count 0.5 mm

Shear tin man (i). Length:300 mm (ii). Material: forged high-quality carbon steel or tool steel (iii). Cutting Capacity:Can cut metal sheets up to 1.2mm to 1.8mm (iv). Handle :PVC rubber sleeve or coating for a comfortable and secure grip (v). Joint: A bolted joint allows for adjustment and ensures blades stay together under cutting pressure.

Hand Rubber Gloves Tester 5000 V (i). Test Potential (Proof-Test Voltage): 5000V (ii). Material: Typically made from natural or synthetic rubber or a combination of both, or latex. (iii). Length: 35cm or 36cm. (iv).Flexible & durable

DC Ohmmeter 0 to 300 ohms mid scales at 20 ohms (i). Resistance Range :- 0 - 300 Ω (ii). Resolution :- 0.1 Ω (iii). Accunacy :- ± 1 % (iv). Display :- Analog Type with mid scales at 20 Ω (v). Power Supply :- AA/AAA size batteries or AV battery (vi) Size :- 180 mm x 130 mm fixed in wooden box (vii). Accessories :- A pair of probes (Good quality ) zero Adjustment facility should be availble

Digital Multimeter , 3.75 digit, 4000 count (i) Max. Display = 4000 count (ii) Digit = 3.75 (iii) DC Voltage Range : up to 1000 V (iv) DC Current Range:up to 20A (v) AC Voltage range : up to 750V (vi) AC Current Range:up to 20A (vii) Resistance Range: up to 20Mohm (viii) Capacitance Range: up to 200microF (ix) Over load protection = Yes

De-soldering pump electrical heated, manual operators, 230V , 40W (i) Material : Aluminum / Steel / plastic (ii) Voltage: 230 V (iii) Power : 40W (iv) Temperature up to 400°C (v) Ultra-high suction capacity (vi) Long nozzle cleaner (vii) Burn resistant ESD safe PTFE nozzle

Precision set of screwdrivers , T5 ,T6,T7 (i) Overall Length -150 mm approx . (ii) Size of Blade : 100 mm (iii) Tip Size : T5, T6, T7 (iv) Magnetic Tip (v) Tip Style: Torx (vi) Tip Material : Alloy steel

Tool maker's vice 100mm (clamp) (i) clamp type table baby vice (ii) fixed base (iii) Material : CAST IRON (iv) Length of Jaw : 100mm (v) Jaw opening size(Minimum) : 140 mm (vi) Thickness of Jaw Plate (Min): 11 mm (vii) Width of Jaw Plate (Minimum) : 21 mm (viii) Spindle Screw dia. (Minimum) : Tr 12x3 (ix) Handle Length (Minimum) : 250 mm (x) Handle Dia. (Minimum) : 14 mm (xi) Hardness (Jaw Plate) : 45-55 HRC (xii) Portable

Tool maker's vice 50mm (clamp) (i) clamp type table baby vice (ii) fixed base (iii) Material : CAST IRON (iv) Length of Jaw : 50mm (v) Jaw opening size (Minimum) : 50 mm (vi) Thickness of Jaw Plate (Min) : 10 mm (vii) Width of Jaw Plate (Minimum) : 15 mm (viii) Spindle Screw dia. (Minimum) : Tr 12x3 (ix) Handle Length (Minimum) : 150 mm (x) Handle Dia. (Minimum) : 8 mm (xi) Hardness (Jaw Plate) : 45-55 HRC (xii) Portable

Crimping tool (pliers),7 in 1 (i) Size : 1.5 sq. mm to 16sq. mm (ii) Plier body material: Carbon steel (iii) Plier Handle Material: PVC (iv) Suitable for Wire Size : (0.6 / 0.8 / 1.0 / 1.3 / 1.6 / 2.0 / 2.6 mm) (v) AWG 22/20/18/16/14/12/10

Magneto spanner set (8 spanners) (i) There should also a small screw driver and a feeler gauge. (ii) Length of each side is approx. 55mm. (iii) Size-6, 7, 8, 9, 10, 11, 12, 13(in mm) (iv) made of alloy steel

File flat bastard 200 mm (i) Body Length(L) 200 mm(Min.) (ii) Tang Length(TL) 60 mm(Min.) (iii) Width(W) 20 mm(Min.) (iv) Thickness (T) 5 mm min (v) No. of Up cut/Inch 25(Min.) (vi) No. of Overcut/ Inch 19(Min.) (vii) Material : High Carbon Steel (viii) Wooden Handle

File flat second cut 200 mm (i) File Length (Without Handle)- 8” (200 mm) (ii) Material : High Carbon Steel (iii) Width 20 mm minimum (iv) Thickness 5mm min. (v) Tang Length :60 mm.(Min.) (vi) Flat Grade- Second cut

Flat nose pliers 100 mm (i) Overall Length: 100 mm.(Minimum) (ii) Material: High Grade Alloy Steel (iii) Tip Shape: Flat (Straight) (iv) Jaw opening size: 15 mm(Min) (v) Flat Nose length:25 mm(Min.) (vi) Jaw Type: Smooth (vii) Handle: Insulated with Grade-I PVC sleeves grip type (viii) Joint Type -Fulcrum

Scriber straight 150 mm (i) Length with handle- 200 mm (ii) Body Dia-4 mm min. (iii) Material mild steel with the point hardened and tempered (iv) Point type - one point end (v) Point angle 8 degree to 15 degree

Continuity tester (i) Economical cell consumption- 1 x AA Battery (ii) Continuity check for house hold& Industrial equipment. (iii) Should be able to test Diode for Open short, transistor for open short PNP/NPN, Transformers, Coils Open Short Tests

Handsaw 450 mm (i) Overall Length: 450 mm (ii) Blade Length 300 mm min. (iii) Blade Width: 12 mm x 46 mm min. (iv) Blade Hardness: 55-60 HRC (v) Thickness 0.8 mm min. Smooth finishing fixed with Brass (vi) Teeth 14 TPI min. (vii) Teeth angle 60 degree (viii) Material High carbon steel (ix) Handle material Plastic / wooden

Allen key screwdriver , 5 no. of set (i)Size of Tip :-2.5 mm,3 mm, 4 mm,5mm,6 mm (ii) Length:- 6" (iii) Material :- Chrome Vanadium Or Carbon Steel (iv) Cushion Grip (v) Drive Type: Hex/AllenSize

Milli Ammeter (DC) , 0 - 500 mA (i) Analog Type DC Milli Ammeter (ii) Range- 0-500mA (ii) Desk Type (iv) Size: 85mm(w) X 120 mm(L) (v) Moving Coil type.

Jacket Stripper/ Coring Tool For 500 Series Cable: (i) Adjustable blades ,used for screen twisted pair cable, Twisted stranded cable, CATV cable, CB antenna cable, SO, SJ, SJT and other types of flexible power cord (ii) Material: ABS (iii) Size: 125 X 70 X 18mm/4.92 X 2.76 X 0.71" (iv) Suitable Stripping range: Coaxial cable RG-59, RG-6, RG-7, RG-11 (v) Flat-Wire and Twisted Pairs 4P/6P/8P, UTP/STP.

Center conductor Cleaner (i) 5", contact type manual leaver Made from high strength glass-filled Lexan material for maximum strength and durability , (ii) Blades are made from a rugged polycarbonate material (iii) Plated handle made of spring steel, covered with a comfortable plastic coating. (iv) Scrapers have four working surfaces and can be sharpened with a fine file.

Universal drop trimmer for RG 6/11 cables (i) Inter-changeable blade cassettes (ii) ONE TOOL, with inter-changeable blade cassettes, will perform all the following cable industry standard preparations: (iii) 1/4 inch (6.35mm) Braid preparation for Series 59, 6 7, 11 cable (iv) 1/8 inch (3.18mm) Braid preparation for Series 59, 6 ,7 11 cable (Cassettes available for 1/4 inch (6.35mm) or 1/8 inch (3.18mm) cable preparation: (v) Series 59/6 Standard, Tri and Quad Shield cables. (vi) Series 7 Standard, Tri and Quad Shield cables (vii) Series 11 Standard, Tri and Trilogy Quad Shield cables. (viii) Series 11Q Belden, Comm. Scope and Times Fiber Quad Shield cables (ix) Blade cassettes color-coded and marked with cable series type and braid preparation dimensions for easy identification. (x) Unique cassette storage compartment holds two extra cassettes. (xi) High impact, "Hi-Visibility Red", polymer construction. (xii) impact-resistant polymer material

F - connecter tool for RG 6/ 11 cables (i) Made of plastic and steel. (ii) Adjustable compression tool with comfortable grip (iii) For use on RG59 RG6 RG11 cable F-Connector (iv) Hardened steel construction with black oxide finished (v) Compatible with: RG6, RG59, and RG11 compression connectors (vi) Material: Plastic and steel

F - connecter compression tool for RG 6/ 11 cables (i) Material – Stainless Steel and plastic (ii) Crimping Tool: The tool is made of high hardness and precision materials. It is light and portable, durable and has a long service life. Adjustable screw head design, can suppress all kinds of length male and female connectors. (iii) Stripping Tool: Multi-function, with stripping and cutting function. Peel a variety of wires, depending on the thickness of the insulator wire, place them in the "U" slot in the front seat of the tool, and then press the pointer to rotate the tool 1-3 times. (iv) Coaxial Compression Tool Range: Very convenient to install a satellite TV dish /CCTV, move cable TV and cable modem, or wire up the cables for your new house. (v) ROTARY Coaxial Cable Stripper, fully adjustable with replaceable blades, removes 4, 6, 8 and 12mm Insulation (adjustable). Just lock the tool over the cable, spin clockwise, then pull off the unwanted portion. (vi) Package includes: 1 x Coaxial Cable Crimper, 1 x Coaxial Cable Stripper, 20x F Connectors

Electronic mechanic

Digital Multimeter , 3.75 digit, 4000 count (i) Max. Display = 4000 count (ii) Digit = 3.75 (iii) DC Voltage Range : up to 1000 V (iv) DC Current Range:up to 20A (v) AC Voltage range : up to 750V (vi) AC Current Range:up to 20A (vii) Resistance Range: up to 20Mohm (viii) Capacitance Range: up to 200microF (ix) Over load protection = Yes

Soldering Iron Changeable bits : 15 Watt , 240 Volt (i) Power : 15 Watt (ii) Input Voltage : 230 V / 50Hz (iii) Replaceable Bit High-Quality Nickel-Copper Plated Bit (iv) Wire: 3 core / 1.5-meter length with 3 pin top plug. (v) This soldering iron rod should attain full operating temperature within seconds

De-soldering pump electrical heated, manual operators, 230V , 40W (i) Material : Aluminum / Steel / plastic (ii) Voltage: 230 V (iii) Power : 40W (iv) Temperature up to 400°C (v) Ultra-high suction capacity (vi) Long nozzle cleaner (vii) Burn resistant ESD safe PTFE nozzle

Precision set of screwdrivers , T5 ,T6,T7 (i) Overall Length -150 mm approx . (ii) Size of Blade : 100 mm (iii) Tip Size : T5, T6, T7 (iv) Magnetic Tip (v) Tip Style: Torx (vi) Tip Material : Alloy steel

Crimping Tool (Pliers) (i) Size: 1.5 sq. mm to 16sq. mm (ii) Plier body material: Carbon steel (iii) Plier Handle Material: PVC (iv) Suitable for Wire Size: (0.6 / 0.8 / 1.0 / 1.3 / 1.6 / 2.0 / 2.6 mm) (v) AWG 22/20/18/16/14/12/10

Magneto spanner set (8 spanners) (i) There should also a small screw driver and a feeler gauge. (ii) Length of each side is approx. 55mm. (iii) Size-6, 7, 8, 9, 10, 11, 12, 13(in mm) (iv) made of alloy steel

Flat nose pliers 100 mm (i) Overall Length: 100 mm.(Minimum) (ii) Material: High Grade Alloy Steel (iii) Tip Shape: Flat (Straight) (iv) Jaw opening size: 15 mm(Min) (v) Flat Nose length:25 mm(Min.) (vi) Jaw Type: Smooth (vii) Handle: Insulated with Grade-I PVC sleeves grip type (viii) Joint Type -Fulcrum

Round Nose pliers : 100 mm (i) Insulated with thick cellulose acetate sleeves (ii) Overall Length: 150mm.(Min.) (iii) Material: Alloy Steel (iv) Joint type: Fulcrum (v) Jaw Type: Smooth Jaw (vi) Jaw Legnth:35mm(approx.) (vii) Tip Type :- Round (viii) Head Thickness: 8mm(approx.)

Scriber straight 150 mm (i) Length with handle- 200 mm (ii) Body Dia-4 mm min. (iii) Material mild steel with the point hardened and tempered (iv) Point type - one point end (v) Point angle 8 degree to 15 degree

Continuity tester (i) Economical cell consumption- 1 x AA Battery (ii) Continuity check for house hold& Industrial equipment. (iii) Should be able to test Diode for Open short, transistor for open short PNP/NPN, Transformers, Coils Open Short Tests

Handsaw 450 mm (i) Overall Length: 450 mm (ii) Blade Length 300 mm min. (iii) Blade Width: 12 mm x 46 mm min. (iv) Blade Hardness: 55-60 HRC (v) Thickness 0.8 mm min. Smooth finishing fixed with Brass (vi) Teeth 14 TPI min. (vii) Teeth angle 60 degree (viii) Material High carbon steel (ix) Handle material Plastic / wooden

First aid kit : (i) First Aid Kit wall mounted (ii) Made of stainless steel of 304 grade with three partitions with lock facility (iii) All drawers have two partitions to divide into 2 sections or 3 sections.

Analog Multimeter Basic Indicative diagram (i) Confirms to IEC61010-1, CAT II 1,000V, CAT III 500V to ground potential (ii) DC Voltage :- upto 1000V (iii) Accuracy: ±3% (iv) AC Voltage upto 1000V (v) Accuracy: ±4% (vi) DC Current :- upto 10A (vii) Accuracy: ±3% (viii) AC Current :- upto 10A (ix) Accuracy: ±4% (x) Resistance :- upto 20M.Ohms (xi) Accuracy: ±3% (xii) Battery Test: 1.5V / 9V/12 V

Electrician knife : 100 mm (i) Length of Blade-100 mm minimum (ii) Blades: Material Carbon Steel of IS 3749:1966 (iii) Heavy-Duty metal Blades (iv) Folded blade, tin opener, screw driver, marline spike, snapper included in the cap of the knife (v) Blade Length: 50 mm, Blade Thickness: 1.4 mm. (vi) Overall Length: 230 mm. (vii) Blade Shape: Straight (viii) Use: To cut wires and cables and stripping off their insulation

Tweezers : 150 mm (i) Total Length: 150mm ±1mm (ii) BladeLength:100mm(min.) (iii) Bladewidth:10 mm(min.) (iv) BladeThickness:1mm(min.) (v) Material: Stainless Steel (nonmagnetic) (vi) Heat Treatment: Hardness of 370 to 410HV. (vii) Features: Tip fine point and pluck with easy precision.

Tweezers – Bend tip (i) Stainless Steel (ii) Insulated (iii) Length : 4”(Min.) (iv) Tip angle :- 450 (v) Hardness of 370 to 410HV. (vi) Antistatic, Anti-magnetic and anti-acid (vii) Cutting-edge parts of pure manual polishing (viii) Non-corrosive ESD safe

Bench Vice : 125mm (i) Size (Length of Jaw/Jaw Plate) : 125 mm (ii) Jaw opening Size (Min.) : 175 mm (iii) Fixed/Movable Jaw Height (Min.): 85 mm (iv) Thickness of Jaw Plate (Min.) :12 mm (v) Width of Jaw Plate (Min.) : 24 mm (vi) Width of Jaw Plate (Min.) :24 mm (vii) Width of Jaw Plate (Min.) :24 mm (viii) Handle Dia (Min.) : 16 mm (ix) Fixed base (x) Material of body: Cast iron (xi) Spindle Nut: Phosphor bronze or Grey cast iron (at least2.5 time the nominal diameter of screw spindle. (xii) Screw Spindle (Trapezoidal threads) and Handle:-Mild Steel. (xiii) Hardness (Jaw Plate):-45-55HRC.

Tools makers vice100mm (clamp type) (i) Clamp type table baby vice (ii) Fixed base (iii) Material: CAST IRON (iv) Length of Jaw : 100mm (v) Jaw opening size(Minimum) : 140mm (vi) Thickness of Jaw Plate (Min): 11mm (vii) Width of Jaw Plate (Minimum) : 21 mm (viii) Spindle Screw dia. (Minimum) : Tr 22x5 (ix) Handle Length (Minimum) : 250 mm (x) Handle Dia. (Minimum) : 14 mm (xi) Hardness (Jaw Plate) : 45-55 HRC (xii) Portable

Tools maker vice 50mm (clamp type table baby vice , fixed base) : (i) Clamp type table baby vice (ii) Fixed base (iii) Material : CAST IRON (iv) Length of Jaw : 50mm (v) Jaw opening size(Minimum) : 50mm (vi) Thickness of Jaw Plate (Min) : 10mm (vii) Width of Jaw Plate (Minimum) : 15 mm (viii) Spindle Screw dia. (Minimum) : Tr 12x3 (ix) Handle Length (Minimum) : 150 mm (x) Handle Dia. (Minimum) : 8 mm (xi) Hardness (Jaw Plate) : 45-55 HRC (xii) Portable

Magnifying lenses : 75 mm diameter (i) Diameter-75 mm(Approx.) (ii) Focal Length:150 mm (iii) Magnification-2.5X (iv) Lens Material: Convex Lens. (v) Chrome plated metal frame around the lens (vi) Handle Material–Bakelite.

Scissors : 200mm (i) Over all Length (A): 200 mm Minimum (ii) Blade length (B): 95 mm (iii) Upper Width (C) : 25 mm (iv) Thickness Dia. (D): 7.9 mm (v) Material: High Carbon steel (vi) Cutting edge hardness range : 500 to 700 HV(35 to 60 HRC) (vii) Handle (Loop) W x H: 29 mm x 41 mm (viii) Welded to the mild steel body and the handle (ix) Comfortable grip

LCD based DPM (i) Range: Voltage DC 20mV to 1000V. (ii) Display: 3 and 1/2 digit. (iii) Input impedance: 10M ohm (iv) To show various range of voltages

Milli Ammeter (DC) : 0 – 500 mA : (i) Analog Type DC Milli Ammeter (ii) Range- 0-500mA (iii) Desk Type (iv) Size: 85mm(w) X 120 mm(L) (v) moving Coil type

Turner

Caliper outside spring joint,150 mm (i) Legs:- Carbon and alloy tools steel. (ii) Spring:- Carbon spring steel. (iii) Fulcrum roller, Adjusting Screw and Nut Hardness:-400-500HV. (iv) Measuring Tip Hardness:-650HV(±50HV)

Caliper inside spring joint150 mm (i) Legs:-Carbon and alloy tools steel. (ii) Spring:- Carbon spring steel. (iii) Fulcrumroller, Adjusting Screw and Nut Hardness:-400-500HV. (iv) Measuring Tip Hardness:-650HV(±50HV)

Caliper odd-leg firm joint150 mm (i) Range: - 0 – 150 mm. (ii) Accuracy: - 0.5 mm. (iii) Material: -Legs, Screw & Nut Washer:-Carbon and alloy tools steel. (iv) Heat Treatment: - Measuring Face Hardness:-650HV (±50HV) (v) Finishing: - Polished. (vi) Nut & Joint:- Nut. (vii)Others: - Odd leg, Adjustable Tip, sturdy &corrosion resistance.

Scriber 150mm x 3 mm (i) Size: -150 X 3 mm (L x Dia.). (ii) Shape: -L shape. (iii) Material: -High carbon steel (iv) Point Hardness:52-58 HRC

Prick punch 100 mm (i) Size: - dia 6x length 100 mm. (ii) Tip angle: -60°. (iii) Material:-High carbon steel (iv) Knurled Body for grip (v) Point Hardness:52-58 HRC (vi) Head/Face Hardness:38-46 HRC (vii) Finishing:- Polished finish.

Divider spring joint 150 mm (i) 9.1 Range: - 0 – 150 mm. (ii) 9.2 Length of Legs:- 150 mm. (iii) 9.3Joint type:- Spring.

Chisel cold flat 20 x 150 mm Shaft and jaw: - Carbon or Alloy Steels (45C8 and 55C4 conforming to IS1570(Part-II):1979).

File flat 250 mm smooth (i) Type of cut: Double cut (ii) Length excluding tang (L): 250 mm (iii) Width (b): 25mm (iv) Thickness (t): 6 mm (v) Length of taper (Ll): 83.3 mm (L/3) (vi) Point thickness (t1): 6 mm (vii) Length of tang (a): 70 mm

File half round 250 mm 2nd cut (i) Type of cut: Double cut (ii) Length excluding tang (L): 250 mm (iii) Width (b): 24mm (iv) Thickness (t): 7 mm (v) Length of taper (Ll): 83.3 mm (L/3) (vi) Point thickness (t1): 7 mm (vii) Length of tang (a): 70 mm

Knurling tool revolving head(Rough, med, fine) diamond and straight (i) Size:- i.i Knurl roller Dimension: - Dia.20x10x5.5mm.(O.D xTxBore dia.) i.ii Shank size:-. Square of size 12.7mm with length 150mm. (ii) Category of Rollers: - Diamond, straight, cross. (iii) Finish: - Rough, medium, fine. (iv) Material:-High speed steel. (v) Others:- Knurl of six pieces set (2 rough, 2 medium, 2 fine) in a single tool.

Screwdriver 10 X 200 mm (i) ScrewDriver Type:Flat (SlottedHead). (ii) Blade Material:Chromium Vanadium Steel. (iii) Handle Material:Cellulose Acetate Transparent.

Spanner adjustable 200 mm BIS/ISICertified(IS:6149:1984) (i) Over all Length (ii) Handle Width (iii) Handle (iv) Thickness (v) Handle Hole for (vi) Hanging (vii) Material

Pliers flat nose 150 mm side cutting a. Over all Length: 100mm.(Min.) b. Material:High Grade Alloy Steel c. Tip Shape:Straight d. Joint type:Fulcrum e. Jaw opening size: 15mm(Min) f. Jaw Hardness:35-50HRC(Min.) g. Flat Nose length:25mm(Min.) h. Flat Nose Thickness:0.7mm(Min.) i. JawType:Smooth j. Handle: Insulated with Grade-IPVC sleeves grip type

Caliper transfer inside 150 mm (i) Range: - 0 – 150 mm. (ii) Accuracy: - 0.5 mm. (iii) Material: - Legs, Screw & Nut Washer:-Carbon and alloy tools steel. (iv) Heat Treatment: - Measuring Face Hardness:-650HV( ±50HV) (v) Finishing: - Polished.

Micrometer Inside up to 25 mm, Least Count 0.01 mm with NABL Accredited lab. Certificate (i) Measuring Range: -0-25mm. (ii) Least Count: -0.01mm. (iii) Spindle Pitch:- 0.5mm. (iv) Material: -Thimble, sleeve, spindle and anvil stainless steel,Frame:-Malleable Cast Iron. (v) Finishing for Spindle and Anvil: -Tungsten Carbide-tipped, micro-lap finish. (vi) Hardness for spindle and anvil:- 530 HV min.

Micrometer Inside up to 25 to 50 mm, Least Count 0.01 mm with NABL Accredited lab. Certificate (i) Measuring Range:- 25-50mm. (ii) Least Count:- 0.01mm. (iii) Material:- Stainless steel. (iv) Setting Ring inner dia.:- 25mm. (v) Finishing:- Chrome finishing. (vi) Hardness for spindle:- 530 HV min.

Gauge Feeler Thickness - 0.05 mm to 0.3 mm by 0.05 and 0.4 mm to 1 mm by 0.1 mm - 13 leaves (i) Measuring Range:- 0.05 mm to 0.3 mm by 0.05mm and 0.4 mm to 1.0mm by 0.1mm. (ii) Length of Blade: 75 mm. (iii) Width of Blade: 10 mm (iv) Shape of Blade: Parallel with outer end semi circular. (v) Hardness of Blade: 400 – 600 HV (vi) No. of Blade:- 13. (vii) Material:- Blade: Flexible steel.Sheath:- Compact steel.

Drill Angle Gauge 45°, 60°, 90°. (i) Measuring Angle: -45°, 60°, 90°. (ii) Material: - Stainless steel. (iii) Finishing: -Polished, free from deformation and sharp edges. (iv) Others: -Supply with plastic case, each angle value should be permanent marked.

Wheel Dresser Diamond (inserted-0.75 or 1 Carat ) (i) Point:- Tapered point tool 1.0 carat- dia. ½ inch x length 6 inch. (ii) Material:- a. Compatible- Diamond, b. Grit- Diamond. (iii) Grit Type:- Coarse. (iv) Others:- This hand held grinding wheel dresser should remove unwanted debris and impurities from the wheelto restore and extend its life.

Sine Bar with centers 200 mm (i) Size: As per syllabus (Centre distance between rollers L1= 200mm) (ii) Material :- The main body of sine bar, supporting rollers ( and support, if required ) shall be made from suitable gauge steel as specified in IS : 7018 ( Part 1 )-I973 ‘Technical supply conditions for gauges: Part 1 General’. (iii) Hardness:- The working surface and rollers shall be hardened to a hardness of not less than 700 HV (60 HRC ) and stabilized. (iv) Others:- Sine bar should placed in the wooden storage box

Twist Drill straight shank 3 to 12 mm by 1 mm (i)Size:- 3-12mm step of 1.0mm. (ii)No. of Drill:- 10 nos. (ii)Type:- Straight shank. (iv)Material:- One piece construction:- High speed steel. (v)Hardness: (a) Cutting portion:- 760 – 900 HV (b) Shank portion:- 240 HV min (vi) Point:- (a) Point angle:- 118 degree. (b) Lip clearance angle:- 8 degree. (vii) Others:- Corrosion resistance,moisture resistant, twist drills should be suitable for heavy-duty applications, twist drills have a hardened body,suitable for drilling of stainless steel,mild steel and non-ferrous materials.

Angle Plate Adjustable - 150 X 175 X 250 mm (i) Size:-78.1.1- Length (L)-250mm. (ii) 2- Width (B)-150mm. (iii) .3- Height (H)-175mm. (iv) Thickness (T)- 22 mm

Tool Maker’s button Standard (i) Size: - 79.1.1:- Length- 200mm. a. 79.1.2:- Height- 40.5mm. b. 79.1.3:- Width- 40mm. (ii) Sensitivity:-1 division =0.05mm/200mm. (iii) Base:- Flat and V type. (iv) Material:- Stainless steel.

Combination Drill / Centre Drill A3, A4 & A5 (i) Body Diameter (OD):- Ø8.00mm (A3),Ø10mm (A4), Ø12.5mm (A5). (ii) Pilot Dia (OD):-Ø3.15mm (A3), Ø4.00mm (A4), Ø5.00mm (A5). (iii) Overall Length:- 48 - 52mm (A3), 53 – 59 mm (A4), 60 – 66 mm (A5). (iv) Material:-High speed steel as per IS7291:1974 (v) Type:- Straight shank, double ended. (vi) Hardness:-760 - 900 HV

Machine Vice - Swivel Base 100 mm Jaw opening (i) Electrical equipments of machine tool as per (ii) Variation allowed -5%, +10% only in size. (iii) - Machinery should be fitted with ISI/BIS marked motors (forming part or parts of machine or equipments). (iv) Switches, starter and stabilizers forming part of machinery should be ISI/BIS marked.

Stool 2.5 Feet (i) Size of stool:-457(H)x305(W)x305(D)mm.(±5mm) (ii).Frame:MSSquarepipesize25x25x2mmfoursidefullweldedbead,minimum50mmtaperisto be provided on legs. All joints are full welded bead and furnished properly four legsjoinedwitheachotherwith25x25x2mmsquarepipe. (iii) SittingFrameSize:305(W)x305(D)mmin25x25x5mmangleframe. (iv)Seat/Top:Sunmicalaminatedplywood25mmthick.Sunmicathickness1mm(Min.)fittedinangleframe.

Angle Gauge for tool grinding Standard (i) Range:- Measuresangles of 120°, 118°, 90°, 60°, 55° . (ii) Thickness:- 0.6 mm. (iii) Material:- Stainless steel. (iv) Heat Treatment:- Hardened . (v) Finishing:- Polishing.

Hand Chaser M-12 & M-16 (External) (i) Type: External. (ii) Length: - 150mm. (iii) Size: - 95.2.1:- Hand Chaser - M12 x 1.5 . (iv) Hand Chaser - M16 x 1.5. (v) Material: - Tool steel. (vi) Types of Thread: - Fine, coarse, right hand & left hand fasteners thread. (vii) Heat Treatment: - Hardened.

Hand Chaser M-12 & M-16 (Internal) (i) Type:- Internal. (ii) Length: -150mm. (iii) Size: -95.2.1:- Hand Chaser - M12 x 1.5 . (iv) Hand Chaser - M16 x 1.5. (v) Material: -Tool steel. (vi) Types of Thread: -Fine, coarse, right hand & left hand fasteners thread. (vii) Heat Treatment: -Hardened.

Thread Plug Gauge M-20 & M-21 (i) Gauge type:- GO / NO-GO with hexagonal handle as per IS5388. (ii) Material: -Gauge steel as per IS1570:1961. (iii) Hardness: -700 HV min. (iv) Others:-Delivered in plastic box with velvet cloth covering inside, nominal size should be engraved clearly on gauges with No and No Go respectively, handle should be powered coated with paint, manufacturer name/trade mark should be marked on handle, No go gauge shall be painted with red paint on the groove.

Thread Ring Gauge M-20 & M-21 (i) Thread Type: - Metric. (ii) Gauge size: - 99.2.1:- M20 X 1.5 (Fine pitch). (iii) -M20 X 2.5 (Coarse pitch). (iv) M21 X 1.0 (Fine Thread). (v) Gauge type: -GO / NO-GO (Thread ring Gauge). (vi) Material: - Gauge steel as per IS1570:1961. (vii) Hardness: - 700 HV min.

Gauge Drill Grinding Standard (i) Product:- Drill bit cutting edge included angle measurement gauge. (ii) Size:- 110x40mm. (LxW). (iii) Thickness:- 1.3mm. (iv) Material:- Stainless steel. (v) Checking angle ( twist drill grinding gauge for point angle):-118°. (vi) Others:-Suitable for drill bits up to a diameter of 50mm, rust proof,supply in a wooden box, Manufacturer name/trade mark with size (gauge angle value) should be marked.

Fire buckets (i) Capacity: 9 litre (ii) Body Material: M.S Galvanized Sheet (iii) Body Shape:ConeType (iv) Top Dia.(Internal):260mm(Min.) (v) Bottom Dia.(Internal):170mm(Min.) (vi) Depth: 270mm(Min.) (vii) Body Thickness: 20Gauge(Min.) (viii) HandleMaterial: Mild steel rod of 10 mm in diameter (ix) Ear Thickness:2.8mm(Min.) (x) Weight:1.2kg(Approx.)

Harihar Trading Company (BID ID -1371485)

BANSAL AND SONS (BID ID -1379563)