REPAIR TO PLASTERING, BRICKWORK, FLOORING, TILLING, PLUMBING, INTERNAL WATER SUPPLY, SANITARY FITTINGS, JOINERY, ATT, WPT, ROOF SHEET, CEILING, PERIODICAL SERVICES ETC TO CERTAIN JCO/OR ACCN AT BMC UNDER GE (C) KOLKATA

Amount

Demolition of cement concrete (Un-reinforced) in ground floor and paving n exc 15cm thick above or below GL complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Taking down existing Water Proofing Treatment with and including roof tiles and padding upto original roof and removing debris from the Site, complete all as specified and as directed.

Taking down old crumple treatment (sheet,filler board etc) by cutting, chiseling, etc. and cleaning the surfaces by scrapping, booming, bruhing, etc. and removing the rubbish from Site to a distance n exc 50.00 Metre complete all as specified and as directed.

Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutter from frames) of any sizes n exc 1.5 Sqm each complete all as specified and directed.

Taking down Chowkat or Frame with shutters (without taking off Shutter from the Frame) exc. 1.50 Sqm but not exc. 4.00 Sqm Each, complete all as specified and as directed.

Taking down Shutters of any description, not exc 1.00 Sqm Each, and keep in Safe Custody for removing to store, complete all as specified and as directed.

Taking down Shutters of any description, exc. 1.00 Sqm but not exc 2.00 Sqm Each and keep in Safe Custody for removing to store, complete all as specified and as directed.

Dismantling floors hearth or wall tilling including cement mortor bedding (but not backing) removing serviceble tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of stone slabs and tiles laid,bedded and pointed in any mortar of any description or thickness in floors, aprons etc all as directed by Engineer-in-charge.

Taking down cement plaster of any description on brick work or stone msonary wall including racking ot joints hacking for key scrubbing down with water etc. complete all as specified and directed.

Taking up or down Steel Water Tubing 15mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use, or removing to store, complete all as specified and as directed.

Taking up or down Steel Water Tubing 20mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use or removing to store, complete all as specified and as directed.

Taking up or down Steel Water Tubing 25mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use or removing to store, complete all as specified and as directed.

Taking up or down Steel Water Tubing 40mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use or removing to store, complete all as specified and as directed.

Taking down unserviceable PVC (SWR) Pipes & Fittings of any size or pattern and in any Position (Measured overall as fixed along the Centre Line over the Fittings and Accessories), complete all as specified and as directed.

Hacking Out Old Broken Glass (any thickness, size, quality or description) from Wooden Frames, Glazed with Putty or fixed with Beads, complete all as specified and as directed.

Anti Termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

Anti Termite Treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

Anti Termite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

M&L for 15mm deep 100% silicon based sealent (Latisil from M/s Laticrete or equivalent product from M/s Pidilite) for crumple joint (40 to 75mm wide) treatment complete all as per manufacturer's instruction and as directed.

Chipping of unsound /weak concrete materials of 50mm average thickness from slabs , beams, columns ,lintel,chajja, fin , facia etc. by any means including tapering all edges, making square shoulders of cavities air or sand blasting etc and cleaning of exposed concrete surface of lightly picking materials by air blasting or sand blasting incl foreign matrials , loose concrete/aggregate etc and disposal of all debris out of MOD land and complete all as specified and as directed by Engr-in-Charge.

Removing rust from existing corroded reinforcement by any means and application of Rust Remover such as Hind Rust Clean (M/s Hindcon) or equivalent from M/s Pidilite/Fosroc and then washing the same to make the reinforcement scale free complete all as per the direction of Engineer-in-Charge Note : Payment to be made on exposed RCC area

Application of anticorrosive paint such as Hind Anti Rust (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc on cleaned reinforcement as per manufacturer's specification complete including labour and material as per direction of Engineer-in-Charge. Note : Payment to be made on 25% of exposed area

Application of bonding coat based on polymer modified cementious material such as Nitobond SBR/Hind Styrene BR (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc @ 0.50 Kg/Sqm (due to rough concrete surfaces) to act as bonding agent between old and new concrete including material and labour as per manufacturer's specification complete all as per direction of Engineer-in-Charge.

Application of polymer modified concrete with mix ratio 1:1.5:3 (1 cement : 1.5 Coarse Sand : 3 Stone aggregate of 10mm nominal size) admixed with acrylic latex polymer such as Hind Styrene BR/Nitobond SBR (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc @ 2.00 Kg per Sqm and plasticiser Hind Plast Super/Conplast SP 337 (M/s Hindcon) or equivalent from M/s Pidilite/Forsoc @ 100Gms.Sqm for an average thickness of 50mm (the concrete to be applied when the bonding coat is still green) including material and labour, scaffolding and formwork etc. as per manufacturer's specification and direction of Engineer-in-Charge

M&L Plain Cement Concrete type C-0, (1:3:6) (12.5mm graded crushed stone aggregate) as in Coping bed plate,hold fast etc,block benching,channeling slightly rounded or chamfered angle and throating including form work and finishing all exposed faces of cement concrete complete all as specified and as directed.

M&L RCC (Nominal Mix) 1:2:4 type B-1 (Using 20mm graded stone aggreagate) as in slab, shelves supported on walls beam & coloumns in floor roof including balconies, conopies, deck slabs & shelves complete all as specified and directed.

Cutting chases, pinning in making good to facing where required and pointing in CM 1:3 to end or edges of landing steps, cills, sunshades, shelves, lintels etc. and cutting chase for concealed water pipe etc. and making good cutting not exc 10Cm girth complete all as specified and directed.

M&L Pulverizes fly ash bricks using class 'A ' old size bricks straigth or curved on plan exc 6m mean radius built in CM (1:6) cmplete all as specified and directed.

M&L Brick Work pulverizes fly ash bricks ,Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

M&L Formwork to Soffits of suspend slab such as Roof slab, Floor slab, landings and similar works horizontal or sloping etc., not exceding 200mm thick ,flat rough finished surfaces of concrete, complete all as specified and as directed.

S&F for 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed.

S&F factory made 2nd class hardwood 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009 complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening with and including 3 Nos. stainless steel butt hinges 75mm long complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter With Wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site complete all as specified and directed.

M&L TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed.

M&L for bituminious fillar board 50mm thick as in fillar material of crumple section complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in cover sheet of crumble joint, fixed with brass screw complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

M&L Pressed steel frames for doors with one or more rebates size of frame 125 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note :- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate

M&L Pressed steel frames for doors with one or more rebates size of frame 105 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed complete all as specified and directed. Note :- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate.

M&L 1.50mm thick power coated aluminium , three track sliding window with three nos shutters made of aluminium section as per drawing no CWE/KOL/TD-33 of section no 1F-1F including necessary jointing cleats, glazing clips, rubber neoprene packing, roller, locking arrangement, handles 2 Nos , anodised aluminium snap beading screws etc.Complete all as specified and as directed. Note Nos :- (i) All window member including fitting & fixture i.e frame, track, shutter frame, etc shall be deem to included quoted rate. Only measure opening size of window. (ii) Only Glass for window & wire mesh shall be measure and paid separately under relevant items of BOQ .

S&F Powder coated aluminium ventilators with louvers and glazing including frame of section over all size of window 600X450mm complete with following specification . (a) Alu frames of size 45x45x1.2mm (b) Rail & Stile 45x45x1.2mm thick (c) 4.80mm thick frosted sheet glass Note :- All ventilators/louvers member including fitting & fixture shall be deem to included quoted rate. Only measure opening size of ventilators/louvers

M&L Framed Work such as Grills, Gratings, etc. with ends of Bars shouldered and/or riveted, or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework of Water Tanks and Similar Work, conforming to Fe-290, Gde-E-165, complete all as speci-fied and as directed.

S&F Butt Hinges extruded brass,bright polished size of Hinges 100 mm (medium weight) and fixed with brass hinge pin complete all as specified and as directed.

S&F Aluminium anodized, Barrel Tower Bolt 200mm long, Extruded Section and fixed, complete all as specified and as directed.

S&F 300mm long Aluminium alloy, anodised, Sliding Door Bolt with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Aluminium alloy Handle 150mm long, Extruded Section, Fabricated type, anodized and fixed, complete all as specified and as directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L 18/19 mm thick Medium density fibre board, exterior grade, fixed to timber framework with screws complete all as specified and directed.

S&F Brass, bright finish or electrogalvanised continuous (Piano) Hinges, width of Flaps (when open) 30mm and fixed, as in repair complete all as specified and as directed.

S&F 40mm dia cupboard knobs fixed with nut screws and washer of wooden finish brass polished complete all as specified and directed.

S&F Floor door stopper of aluminium body and tongue, anodised with hard drawn steel spring (overall length of cover plate 150mm) complete all as specified and as directed.

M&L for 75mm thick PCC (1:3:6) type C-2 (Using 40mm graded stone aggregate) as in plinth protection laid in panels, finish the top surfaces even and smooth without using extra cement complete all as specified and directed Note:- Construction joints will be provided at interval of 2.5m length and filled with bitumen 80/20 mix with sand in ratio of 1:3 and cost of the same shall be deemed included in quoted rate

M&L Cement Concrete type B0 (1:2:4) (12.5mm graded aggregate) as in ,padding , benching and filleting ,finishing concrete surfaces fair and even, complete all as specified and as directed.

M&L for 10mm thick screed bed or bedding over roof surfaces when concrete is still green with including WPC in cement mortar 1:4 complete all as specified and directed.

M&L Water Proofing Treatment on existing cleaned RCC Roof with the following Specifications and Manufacturer's instructions, complete all as specified and as directed :- (a) Preparing and cleaning of fully dry surface as per IS:3067-1966. (b) Applying Bitumen Primer conforming to IS-3384-1986 over the Cleaned Plastered Surface @ 0.40 Litre per Sqm. (c) Applying a layer of APP based Polymeric Membrance; 3.0mm thick (minimum) weighing 3.60 Kilogram per Square Metre (reinforced) with Polyster Non Woven Fabric weighing not less than 160 Grams per Square Metre by Torch application. The overlaps shall be minimum 100mm on the Transverse direction and 75mm on Longitudinal direction.

M&L Cement Concrete type B0 (1:2:4) (12.5mm graded aggregate) 25mm thick, in Flooring ,padding , benching and filleting ,finishing concrete surfaces fair and even, complete all as specified and as directed.

M&L joint free non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.11 Sqm but not exc 0.18 Sqm on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L joint free non skid ceramic coloured tiles 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor set and jointed in in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L joint free non skid ceramic coloured tiles (double charge) 8-10mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Granite (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, in Steps, Cooking Platforms and like, Set in Screed bed of 20mm thick in Cement Mortar 1:4 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing including half round edges, complete all as specified and as directed.

M&L Glazed Ceramic Coloured Tile 300x200x7mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Glazed Ceramic Coloured Tile 450x350x7mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Applying polymer modified cement mortar rendering 20mm thick in CM 1:3 on wall duly mixing polymer modifier "Nitobond SBR of M/s Forsoc Chemical India (Pvt) Ltd" or "Hind Styrene BR of Hindcon Chemical Ltd" or equivalent make of M/s Pidilite Industries @ 7 Litre per bag of cement complete finished even and smooth without using extra cement as per manufacturer's specification complete all as specified and directed.

Cutting out existing cracks in concrete surfaces forming grooves of 25mm x 40mm size, cleaning the groove thoroughly with blower, applying primer coat of the mix of IPH CC Resin & Hardner in equal proportion with suitable brush to form a film on the surface of groove, filling the groove with putty made by mixing IPH CC Resin, Hardner and admixture in the proportion of 1:1:4 and finally applying the sealing coat of the same mix and in the manner primer coat is applied with following min. coverage per running metre length of groove :- Material Priming Coat Putty Filling Seal Coat Resin 60 Gms 100 Gms 40 Gms Hardner 60 Gms 100 Gms 40 Gms Admixture - 400 Gms -

M&L rendering 15mm thick in CM (1:6) on other than fair faces of brick work or concrete surfaces even & smoth without using extra cement complete all as specified and directed

M&L rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces finished the surfaces even and fair without using extra cement and using water proofing compound as per manufacturer instruction complete all as specified and directed

M&L rendering 5mm thick in CM (1:3) as in ceiling surfaces even & smooth without using extra cement complete all as specified and directed.

"Supply only" liquid water proofing compound (ISI marked) complete all as specified and directed. Make:- STP NO 1/ PEDILITE(DR FIXIT)/ FOSROC/ CICO/ SIKA

S&F 4.0mm thick frosted glass panes and glazing with oil putty in square nexc 0.5 Sqm each pane complete all as specified.

S&F 4.80mm thick tinted sheet glass , pin head type and glazing in squares exc 0.5 sq. M in each pane complete all as specified and as directed.

M&L Preparing old decorated Plaster Surfaces of Wall and applying One Coat of White Wash (any colour/ tint) complete all as specified and as directed.

M&L Preparing old decorated Plaster Surfaces of Wall and applying One Coat of oil bound (any colour /tint) complete all as specified and as directed.

M&L Preparing old decorated Plaster Surfaces of Ceiling and applying One Coat of oil bounded distemper complete all as specified and as directed.

M&L Preparing new Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over two coat of thick BIRLA/JK water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L Preparing new Surfaces of ceiling and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over two coat of thick BIRLA/JK water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L Complete removal of old decorated surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L Preparing newly plastered surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L Preparing old decorated plastered surfaces of Walls and applying One Coats of Exterior Emulsion Paint Weather Coat (any colour /tint) (as per Manufacturer’s instructions), complete all as specified and as directed. Make- Asian (apex ultima), Berger Paints-Weathercoat Lifelong7 ,Dulux Paints-Wheathershield Ultraclean

M&L Preparing old decorated plastered surfaces of Walls and applying One Coat of Cement Base Paint complete all as specified and as directed.

M&L Preparing new Wood and Wood Based Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Pink Primer, complete all as specified and as directed.

M&L Preparing new/old Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing old Wooden Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

M&L Preparing old Steel Surfaces of any description not otherwise decribed over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and as directed.

S&F 20mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F 25mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F 40mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F 50mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F Chromium plated Bib taps for 15 mm bore of pipe complete all as specified and directed. Make : Essco (MQT-511KN) or equivalent make specified in the particular specification

S&F Brass chromium plated long body bib cock with Wall Flange screwed for 15 mm bore pipe as in repair complete all as specified and directed Make : Essco (MQT-512KN) or equivalent make specified in the particular specification

S&F Brass chromium plated two in one tap with Wall Flange screwed for 15 mm bore pipe as in repair complete all as specified and directed Make : Essco (MQT-512ANKN) or equivalent make specified in the particular specification

S&F Brass chromium plated Pillar Tap screwed for 15 mm bore pipe complete all as specified and directed Make : Essco (MQT-508KN) or equivalent make specified in the particular specification

S&F ABS body chrome plated shower rose 125mm size including fixing to steel pipe or union complete all as specified and directed Make : Essco (EOS-542A) or equivalent make specified in the particular specification

S&F Shower arm 240mm long round shape with flage including fixing to steel pipe or union as in repair complete all as specified and directed. Make : Essco (ALE-536A) or equivalent make specified in the particular specification

S&F 15mm bore brass chromium plated Angular Valve with Wall Flange complete all as specified and directed. Make : Essco (MQT-526KN) or equivalent make specified in the particular specification

S&F 15mm bore brass chromium plated 2 way Angular Valve with Wall Flange complete all as specified and directed. Make : Essco (MQT-526AFKN) or equivalent make specified in the particular specification

S&F Chromium plated Health faucet with 8mm Dia, 1.2 Meter long flexible tube and wall hook with N.R.V (Back Flow Preventer) as in repair complete all and specified and directed Make:- Essco (CAT No. ALE-ESS-583) or equivalent make specified in the particular specification

S&F White Plastic Seat and Cover for Pedestal Pan, Closed Pattern with Recessed Bottom including Mild Steel Chromium Plated Aluminium Hanging Device and fixed-in- repairs, complete all as specified and as directed. Make:- Prayag (CAT No. 721) or equivalent make specified in the particular specification

S&F Vitreous China White Squatting Pan ‘ORISSA’ Pattern, size 580x440mm with ‘P’ or ‘S’ Trap, Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan including Flushing Cistern and Flush Pipe, fixing with and including provision of cement Concrete Bedding including taking down old one complete all as specified and as directed. Make - Hindwire cat No 20042 or equvilant of approved make specified in particular specification.

S&F White PVC Flushing Cistern 10 Litre capacity, Low Level Valve Less, Syphonic Action type with Inlet, Ball Valve, Float and Handle including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 and fixed including taking down old one complete all as specified and as directed. Make : Parryware Model No- C-8090, Cera cat part No CONGO B1010109 or equivalent model as specified in Particular Specification here in after.

S&F PVC Conncetions 15mm size with PTMT Nuts of length 450mm as in repair complete all as specified and as directed.

S&F triple layer PVC water storage tank cylinderical, verticle with closed top hoisted and fixed in position tank capacity 500 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 25mm outer diameter for CPVC pipe & making connection for inlet and outlet including dismental of old water tank and removing from site. complete all as specified & directed.

S&F triple layer PVC water storage tank cylinderical, verticle with closed top hoisted and fixed in position tank capacity 2000 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 40mm outer diameter for CPVC pipe & making connection for inlet and outlet including dismental of old water tank and removing from site. complete all as specified & directed.

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia PTMT Waste Fitting, a pair of Cast Iron Brackets duly painted Stand including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including unserviceable old one complete all as specified and as directed. Make - Parryware Model No-C0406(SP)/34(CTH)

S&F UPVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), Type "B" single socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed.

S&F UPVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), Type "B" double socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed.

S&F UPVC (SWR) Bend 110mm bore (dia), any type, and Jointing with Solvent Cement, as in repair complete all as specified and as directed.

S&F UPVC (SWR) Junction 110mm bore (dia), Single (Single T) equal or unequal and Jointing with Solvent Cement, complete all as specified and as directed.

S&F UPVC (SWR) Nahani/Floor Trap 75mm bore (dia) Outlet, Plain with Grating and Jointing with Solvent Cement, as in repair complete all as specified and as directed.

S&F Vitreous China White Wash down Water Closet Pan (Pedestal Pattern) with "p" or "s" trap front or back inlet including fixing Bolts with and excluding 10 litre capacity low level Flushing Cistern matching with water closet colour with inlet ball valve float handle and providing 32mm dia PVC flush pipe including plastic water closet seat with flat botton cover (coloured) fixed with mild steel chromium plated or aluminium hinging device complete all as specified and as directed. Make - Parryware Model No-C0297,C8090 or equivalent make as specified in the particular specfication.

UNITED ENGINEERS

SHEIKH ENTERPRISE

UNIVERSAL TRADING CENTRE

DGR CONSTRUCTION

MODERN AGENCY

M/S SRINIVASA CONSTRUCTION

DEB AND COMPANY

MS JYOTI INDUSTRIES

ARJUN DAS VALECHA