ADDN ALTN AND SPECIAL REPAIR IN BLDG NO T-23 AND T-26 OF MED REGT AT MIL CANTT AJMER UNDER G NASIRABAD

Amount

Taking down cement or cement lime plaster on stone/brick wall, ceiling inlcluding raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces or surfaces other than fair face of brick work of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in CM 1:4 on stone masonry, external surfaces finishedeven and smooth without using extra cement, complete all as specified and directed.

Dubbing out average 10mm thick in CM 1:4 on irregular faces of walls or concrete chajjas etc complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer over 1 mm thick wall care putty complete all as specified and directed.

M & L for preparation old decorated surfaces of walls and providing one coat of cement base paint, complete all as specified and directed.

M & L for preparation new plastered surfaces of walls and providing two coat of cement base paint over a coat of primer complete all as specified and directed.

Demolition of cement concrete (unreinforeced) in floors and paving n.exc 15cm thickness (above or below ground level) complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 20-25mm thick over and including 15mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the smooth of the slab including rubbing & polishing complete all as spd & directed.

M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for factory made 60mm thick machine pressed precast cement concrete coloured, reflective type interlocking paver blocks of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

M&L for PCC 1:2:4, type B-1 (using 20mm stone crushed agg.) as in rounded or chamfered on edges in any description complete all as specified.

Supply only water proofing compound ISI Marked complete all as specified and directed.

Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion ordered and directed.

M&L for random rubble stone walling uncourses, built in CM (1:6) complete all as specified and directed.

All as per item no. 16.00 above but except stone.

M&L for brick work with old size bricks straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc 20mm as specified.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) n exc 1.50 sqm each, removing from site and making good disturbed surface of walls in cement mortar (1:3) complete, all as spd & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm and n.exc 4.00 Sqm each removing from site and making good disturbed surface of walls in cement mortar (1:3) complete, all as spd & directed.

S&F mild steel framed work as in doors / gates / steel frames / chowkats etc. of angle or other section with gusset plates, rails, braces, etc., complete conforming to Grade E-165 (Fe 290), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position complete.

S & F second class HW Hollock/Bonsum/Sal 35mm thick, factory made, plain framed, paneled shutter (Three panels) with panels of 9mm thick BWP grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive conforming to IS-710. The size of rails & style shall be as per IS-1003 (part-I) kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as per specified and directed.

S & F for 2nd class HW 35 mm thick, gauged and skeleton shutters (Three Panels), factory made open rebated and prepare to receive glass, gauge etc (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. Size of members of shutter shall be as specified in SSR 2009 Part-I, section 8 clause Member shall be kiln seasoned as per IS-1141 & chemically pressure treated as per IS-401 complete all as specified and directed.

S&F Steel window/ ventilator glazed and gauged (combination) with side hung/ top hung shutters incl box type / projecting type hinges, and steel peg stay, handle & locking arrangement and frame made out of 1.25mm thick pressed steel frame complete including necessary AC/Cooler arrangement in window & guard bars complete all as as specified and directed.

M & L for 20 to 25 mm thick machine cut kota stone Shelves including rubbing & polishing and set in CM (1:4) including cutting inserting into wall not less than 50mm deep and making good to disturbed surfaces complete all as specified and directed.

S & F 300mm long aluminium alloy,anodised, sliding door bolts with hasps, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S & F extruded aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, ISI marked, 150 mm long complete all as specified and directed.

S & F 125mm single action spring hinges,mild steel with steel wire spring, stove enaelled black, complete all as specified and directed.

S&F mild steel butt hinges, medium weight, cold rolled, ISI marked of size 100 mm, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as spd & directed.

M & L for preparation of new wooden surface over 10cm width or girth and applying two coats of synthetic enamel paint of Ist quality over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of red oxide primer complete all as spd & directed.

S&F 3.00 mm thick sheet glass, ordinary / figured quality & glazing with oil putty not exc 0.50 Sqm each pane complete all as spd & directed.

Taking out of old grill & M & L framed work such as grills, gratings, etc, with ends of bars shouledered and /or reiveted ,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of watertanks and similar work coforming to Fe 290m Gde E-165 complete all as spd and directed.

Dismantling asbestos Cement (corrugated, semi corrugated, etc) sheets in roof covering complete all as specified & directed.

S & F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ Lor J type hook complete all as specified & directed.

S & F for pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ Lor J type hook complete all as specified & directed.

Dismantling of ceiling board/lathing any thickness including frame work complete all as specified and directed.

Providing & Fixing false ceiling with fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-charge. Make: Everest/Armstrong

Dismantling of timber scantling 40 Sq cm and over in section in any position complete.

S & F framed work as in roof trusses purlin, rafter and batterns of angle or other section with gusset plates , rails , braces, etc complete of Fe 410-W (Gde E-250) , drilling for fixing of steel sheeting or other covering doors etc to be prepared for hanging complete all as spd and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc.

Disconnecting and taking down unserviceable sub main wiring of any size including steel/PVC conduit and accessories & removing from site and making good the disturbed surfaces, complete all as specified and directed.

Taking down carefully by unscrewing from boards / outlet boxes, fittings and fixtures such as switches, sockets etc for re use at site or carrying to the store(to be measured only when found serviceable in all respects complete for reuse.) complete all as specified and directed

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type pressed steel modular terminal box and modular white cover plate with frame for suitable module as per site requirements for mounting of modular switches, sockets, fan regulator etc and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth for the following, complete all as specified and directed. Make of wire- Havells/Polycab/Anchor/Finolex. Make of PVC conduit -AKG/Plaza/Kalinga

One light point controlled by one, one way switch.

One Ceiling fan/wall fan/exhaust fan controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One three pin 5 Amp socket on independent board.

All as per item No. 48.00 here-in-before but with 2.5 Sqmm, for one 5 pin 5/15 Amp socket on independent board including 1.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F modular switch 1 way 6/10Amp , 1 module, complete all as specified and directed.

S&F modular switch 1 way 16Amp, 1 module, complete all as specified and directed.

S&F modular socket 6Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F mdoular socket 6Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm.

Taking down existing exhaust fan & wall mounted fan and re-use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

S&F exhaust Fans AC single phase 230/240 volts of size 300 mm sweep with louver including connecting with three core flexible copper wire from ceiling rose to connector of fan complete all as specified and directed. Make:- Havells model ventil air DB or equivalent model from Bajaj/ Usha

S&F lamp holder PVC/polycarbonate type with back plate complete all as specified and directed. Make : Cona / SSK / Havells

S&F LED box type tube light fitting 20 watt made up of CRCA sheet with pre wired double sided connections including 1x20 watt retrofit LED tube rod with extruded aluminium body , PC diffuser and inbuilt driver , double sided connection, complete with all accessories internally prewired. Make Havells/Bajaj/Philips/Crompton

S&F ceiling fan 1200 mm sweep , 230 Volts, AC , 50 Hz, copper winded motor, BE star rated white colour complete with motor, blade set of three nos , down rod, canopy, shackle assy. Make:- Havells/Bajaj/ Usha

S&F LED light fittings, 10 W bulk head luminaries 230V, 50 Hz complete with all accessories and including connecting up with three core copper conductor cable with suitable size complete all as specified and directed. Make :- Havells Cat Part No LHEOAP7UZ6W010 or equivalent model of Philips/Crompton

Supply, fixing and testing energy saving street light luminaire 15 watt LED , pressure die cast housing with high power LED as lighting source and lens embedded PC cover with IP 66 protection incl connecting with three core copper flexible wire from ceiling rose to connector of light fitting complete all as specified and directed by Engr-in-Charge. Make : Havells, Cat Part No. ENDURAPEARLSL15WLED757SASYTOPC, or equivalent model of Crompton/Philips

S&F street light bracket made of 32 mm GI pipe , 1.2 mtr lenght fixed with two nos of clamp , nut and bolts complete all as specified and directed.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 6 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 6 sqmm multi stranded copper conductor cable.

S&F MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed. Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S&F MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate complete all as specified and directed. Make: Legrand/Schneider/Seimens Note: MCB DB and MCB SP/SPN will be of same make.

S & F MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F MCB SP, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S & F MCB SPN, 240 volt, 36 to 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

S&F MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'C' curve complete all as specified and directed. Make : Legrand (DX-3), Schneider (Acti-09), Siemens ( Betagard)

Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, cable laying and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed.

Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly complete all as specified and as directed.

M & L for laying of bricks locally available sub class 'B' bricks, non-modular sizes as per IS 1077: 1992 for cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable all as directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core complete all as specified and as directed.

Supply and fixing tubes light grade GI tubing 50 mm dia with all fitting laid in trenches complete all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground vertically to a depth not less than 2.25m below ground level with top edge of the earth plate at a depth not less than 1.5m below ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel and other end of earth wire connected to main switch board and protected by galvanised iron pipe light grade 15mm bore and water pipe 20 mm bore GI med grade with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover with handle all as specified and shown in elect plate No 3 of SSR Part-I of 2009 including dismantling of old unsv existing earthing complete all as specified and as directed.

SHREE GURU NANAK CONSTRUCTION COMPANY

M/s SUNIL ENTERPRISES

kirtiman traders

ANAM BUILDCON

Pawon Kumar Barik