SPL REPAIRS TO STRUCTURAL MEMBERS, CHAJJA, ROOF TREATMENT AND OTHER B / R WORKS OF BLDG NO P 28 AND P 28 FGH AND CERTAIN MINOR WKS UNDER GE(W) COLABA MUMBAI

Amount

Provision and erecting vertical scaffolding unserviceable (debries net), made out of high density polyethyelene for dust and debries control and keeping the same during the period of works and including dismantling and taking away after after completion of work all as specified and directed.

Identifying and marking carefully the damaged reinforced concrete by tapping with light hammer and chipping of unsound weak concrete and plaster material from slab/beams/columns etc. with power/hand driven chisel as directed by the engineer-in-charge upto 40 mm average depth including saw-cutting of all edges making square shoulders of the cavities all as specified and as directed.. Note 1: All loose unsound and cracked concrete shall be removed out side MD land. Note2 : Thickness shall be measured excluding plaster)

Cleaning loose concrete if any all around reinforcement including from behind the reinforcing bars to give an average 10 mm thick (but not less than 10 mm clear air gap) and cleaning reinforcement of total rust using alkaline rust remover with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washed with water and allowing it to dry complete all as specified and as directed. Note1 : - Length of reinforcement bars cleaned of rust all around shall be measured for payment. Note2: Thickness shall be measured excluding plaster

M&L for applying two coats of epoxy based passivating, protecting & bonding coat of zinc rich system (Nitozinc (R) primer of Fosroc and equivalent of SIKA/Dr Fixit Pidilite/ Krishna Conchem) as approved by the Engineer-in-Charge for old and new reinforcement of any dia complete all as specified and as directed. Note: Epoxy based passivating, protecting & bonding coat of zinc rich system shall be paid for separately.

M&L for mixing and applying SBR latex modified cementitious bond coat using cement 2.2 kg per square metre on prepared concrete surfaces of parent material all as specified and as directed.

M&L for providing and placing in position micro-concrete, grade M-40, which shall be cement based prepacked single component, chloride free, non-shrink, free flow, self compacting, ready to use after mixing water in specified proportion, obtained from Fosroc / SIKA / BASF/ Dr Fixit, thickness of section upto 75 mm all as specified and directed by the Engineer in charge (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument)

S&F in repairs pre-painted roof metal sheet of mangalore tile design profile hot-dip aluminium-zinc alloy metallic coated profile steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick of a colour having yield strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed. Makes:- Tata Steel/JSW colouron +/Treckdeck/CRIL/Essar steel(AM/NS).

Supply & fix in repairs pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPA as in roof coverings /claddings to wall, fixed with self tapping screws including scafoldings of any height all as specified and directed.

S&F hot rolled medium and high tensile structural steel of grade E-250 quality A conforming to IS 2062: 2011 as in joist, channel, angle, flat iron or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20 mm of the length indicated) all as specified and directed.

Demolition of cement concrete in ground floor n.exc 15cm thickness (below or above ground level) and removing the demolished material and debris out side MD land all as specified and directed.

Demolition of cement concrete (re-inforced) in ground floor n.exc 15cm thickness (below or above ground level) and removing the demolished material and debris out side MD land all as specified and directed.

M&L 75 mm PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection, flooring/subbase including necessary shuttering all as specified and directed.

M & L for plastering 20-25mm thick (Avg) epoxy based Polymer modified cement mortar in two coats, 15mm base coat and subsequent finishing coat with and including curing as per manufacturer's instruction complete all as specified and as directed by Engr-in-Charge. Make- Dr Fixit Repair Pro Polymer Mortar, FOSROC-RENDOROC S2-structural grade Polymer Mortar, Shalifix FRM Polymer Modified Fibre Reinforced Mortar of STP or equivalent as approved by the Engineer-in-Charge

M&L light shade vitrified coloured ceramic tiles 10 mm thick (Square/rectangular) polished area of each tile not exceeding 0.36 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles inluding Screed bed or bedding layer of mortar 15 mm thick in (1:6) for laying floor finishes all as specified and directed.

M&L light shade vitrified coloured ceramic tiles 10 mm thick (Square/rectangular) polished area of each tile not exceeding 0.36 sqm in vertical surfaces such as skirtings and dados set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles including rendering 10 mm thick on fair faces of brick work in CM (1:4) all as specified and directed.

Dismantling of floor hearth or wall tiling/stone including cement mortar bedding but not backing and removing rubbish off the primises all as specified and directed.

M&L for digital coloured glazed ceramic tiles 300x450x7mm thick in vertical surfaces (including designed borders ) such as skirting and dados set and jointed in neat cement slurry pointed in coloured cement to match including rendering 10 mm thick on fair faces of brick work in CM (1:4) all as specified and directed. Note:- Rate of Designer border in vertical surface will be deemed into quoted rates.

M&L Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles all as specified and directed.

M&L in repairs machine cut kota stone slab flooring 18-20 mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to mirror finish inluding screed bed or bedding layer of mortar 15 mm thick in (1:6) for laying floor finishes all as specified and directed.

All as per Item No 19 above but in riser of steps, skirting, dado and pillar laid over cement screed and jointed over rendering 10 mm thick on fair faces of brick work in CM (1:4) all as specified and directed.

M&L granite (of any type and colour) 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing laid in steps/floors/Jambs/WHB conters and all other similar works in approved design over 20 mm thick screed bed in cement mortar 1:4 all as specified and directed.

Dismantling of ceiling board (plup insulation or insulation etc) or insulation board any thickness including cover fillet and grid frame work all as specified and directed.

M&L anodized aluminium snap grid of size of 605mm x 605mm and sections incorporated in frame work shall conform to IS 733, IS 737 and IS 1285 and snap grid frame work shall be fixed to ceiling with supporting hanger 6mm dia mild steel rod, J bolts with necessary bolts, nuts and washers all as manufacturer instruction, the main & cross tees shall be jointed at junction/crossings with anodized aluminum angle bracket of size indicated it shall be 19.05mm x 19.05mm x 1.45mm, weighing 0.14 Kg per RM, fixed with suitable mild steel, bolts nuts and washer all as per manufacturers instruction, the snap grid shall be supported at ends all along the wall with anodized aluminum angle of size as indicated along if not indicated it shall be 38mm x 25mm x 2.18mm, weighing 0.358 Kg per running meter all as specified and directed.

M&L 8 mm thick ceiling board of calcium silicate of siliceous and calcareous materials reinforced with cellulose fibre for fixing in 605 X 605 mm grids all as specified and directed. Note:- Frame work for ceiling shall be measured and paid separately.

Taking down cement plaster of any description from brick wall surfaces etc including racking out joints and hacking for key, scrubbing down with water all as specified and directed.

M&L 15 mm thick cement plaster in CM (1:6) on brick work/ RCC wall and finish the surface fair and even without using extra cement all as specified and directed.

M&L rendering 15mm thick in cement mortar 1:4 using intergral water proofing compound on fair faces of brick work to be finished even and smooth (with out using extra cement all as specified and directed. Note: Integral liquid water proofing compound to be used in per bag of cement shall be as per manufacturers instructions and paid separately under respective items.

Supply only liquid integral waterproofing compound

M&L for complete removal of existing treatment and applying two coats of oil bound distemper over a coat of alkali resistant priming paint over 1mm thick (average) Birla wall care putty all as specified and directed.

M&L for preparation of new plastered surfaces and applying two coats of oil bound distemper over a coat of alkali resistant priming paint over 1mm thick (average) Birla wall care putty all as specified and directed..

M&L for preparation of old painted wood or wood based surfaces, of any description, not otherwise described over 10 cm width or girth and apply one coat of synthetic enamel paint all as specified and directed.

M&L for preparation of new wood or wood based surfaces, of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed. .

Taking down chowkhats or frames with shutters (without taking of shutters from the frame) area n exc. 4.00 Sqm each all as specified and directed.

Taking down shutters of any description area exc. 1.00 Sqm but nexc 2.00 Sqm all as spcified and directed.

S&F 2nd class hard wood plain solid straight chowkhat and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joint all as specified and directed.

M&L for preparation of wood and wood based materials, new or old, of any description and girth, not otherwise described, treating small articles such as holdfasts, end of posts, backs of chowkhats, etc area n. exc. 0.1 sq m each and treated with tar or coal tar black paint all as specified and directed.

S&F 35 mm thick 2nd hard wood rail and style plain framed panelled shutters (any panel) with lock rail and panel of 9 mm thick B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and style as per IS 1003 (Part-I) kiln seasoned and chemically pressure treated all as specified and directed.

S&F to chowkhats of 2nd class hard wood 35mm thick glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc(without sash bars) edges of framing plain, chamfered or rounded, fittted with cut and mitred beads for securing gauge, etc sizes of member of shutter as specified SSR part-I Section 8 clause 8.24 (a) complete all as specified and directed.

S&F Aluminum alloy anodised sliding door bolts of 300mm long with hasp stapple all as specified and directed.

Taking down shutters of any description n exc. 1.00 Sqm all as spcified and directed.

S&F for stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden/ aluminium beadding all as spcified and directed

S&F in repair stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden/ aluminium beadding all as spcified and directed

S&F aluminium anodised 200 mm barrel tower bolts of extruded section all as specified and directed.

S&F aluminium handle 150 mm cast type anodised all as spcified and directed

S&F 100 mm butt hinges extruded aluminium alloy with galvanized mild steel hinges pin anodised type `C'-22 all as specified and directed.

S&F in repair vitreous China squatting pan, ' Orissa patteren, size 580 x 440 mm white, with integral footrests (excluding flushing cisteren and flush pipe) including taking down existing squating pan all as specified and directed. Make : Cat Part No S3010104 of Cera or Equivalent in Hindware / Parryware.

S&F in repairs 10 litre capacity PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of any size all as specified and directed. Make : Cat Part No B1010106 of Cera or Equivalent in Hindware / Parryware.

S&F in repair vitreous china wash basin white, flat back, size 580X450 mm including cutting for pinning in ends of brackets all as spcified and directed Make : Cat Part No S2040139 of Cera or Equivalent in Hindware / Parryware.

S&F in repairs for vitreous china, bowl urinal flat back, size 465 x 355 x 265mm white (min) with union and grating for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) including providing and fixing plugs, securing urinal to plugs with and including, 60 mm long brass screws, pointing around urinal back in cement mortar 1:2 (excluding fixing supply pipe to flushing cistern, trap and waste pipe) all as specified and as directed)

S&F PVC connection 15mm size PTMT nuts of length 450 mm all as specified and directed.

M&L in repair CP towel rail 61 cm long all as specified and directed.

M&L in repair CP soap dish all as per cat part all as specified and directed.

S&F as in repairs 15 mm bore angular valve cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions all as specified and directed

S&F as in repairs 15 mm bore concealed stop cock (regular body) cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions all as specified and directed .

S&F in repairs15 mm bore piller taps cast copper alloy, with capstan heads, chromium plated, screwed down, fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed sunk and fly nuts all as specified and directed

Taking up or down steel tubing and connection including cleaning for refixing or removed to store 15 mm dia bore all as specified and directed

Taking up or down steel tubing and connection including cleaning for refixing or removed to store 20 mm dia bore all as specified and directed

Fixing only old 15 mm steel tubing and including cleaning in positon (walls, ceiling and floor etc all as specified and directed

Fixing only old 20 mm steel tubing and including cleaning in positon (walls, ceiling and floor etc all as specified and directed

S&F GI tubing 15mm bore medium grade with all fittings and fixed complete to wall and ceiling or laid in floors all as specified and directed

S&F GI tubing 20 mm bore medium grade with all fittings and fixed complete to wall and ceiling or laid in floors all as specified and directed

M&L cutting chases, pinning in making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good, cutting nexc. 10cm girth all as specified and directed.

M&L for PVC (SWR) multi floor trap with grating including jointing with solvent cement for diameter of 75 mm outlet all as spcified and directed Make: Prince/Supreme/Kisan/Reliance/Finolex.

M&L for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and directed. Make: Prince/Supreme/Kisan/Reliance/Finolex.

S&F in repairs 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, sealed with adhesive suitable for PVC pipes and laid in trenches or fixed to walls all as specified and directed. Note : upto any height and including necessary scafolding

S&F 75mm dia PVC (SWR) bends with access doors any radius all as spcified and directed

S&F 75 mm dia PVC (SWR) vent cowl all as spcified and directed

S&F in repair curtain rod (decorative type) 20 mm dia of SS as approved by Engr-in-charge all as specified and directed. Note : The rate include for any colour and of any design

S&F in repairs curtain brackets decorative type (antique), for receiving single/double curtain rod, fixing for 20 mm rod all as specified and directed.

S&F stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement all as spcified and directed

M&L machine pressed precast concrete coloured interlocking paver block of any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and no pigments all as spcified and directed

S&F in repairs roof tiles, Mangalore pattern, interlocking at side joints, laid dry all as spcified and directed

S&F in repairs second class hardwood clean sawn battens at 30cm centres sectional area exc 15 & n exc 25 Sqcm including scafoldings of any height all as specified and directed.

M&L for timber framed and fixed Second class hard teak wood in scantlings all as spcified and directed

M&L for preparation of old painted steel surfaces of any description over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint all as spcified and directed

M&L for preparation of new steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide, zinc primer all as spcified and directed

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil all as specified and directed.

Excavating in post holes (or similar holes) in soft/ loose soil each n exc 0.5 Cum and getting out, returning, filling in , removing surplus soil to distance not exceeding 50.00 mtr and raming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, complete all as specified and direceted.

S&F steel work of grade-3 as per IS 10748 in tubular trusses including special shaped washer etc. complete using ERW or HRIW welded tubes conforming to IS 1161: 2014 (Yst 240 Grade) all as specified and directed.

M&L 100mm thick PCC 1:4:8, type D-2, (using 40 mm graded crushed stone aggregate) as in subbase to flooring and other similar works all as specified and directed.

M&L rubber moulded glossy finished precast concrete interlocking paver block of any shape and size confirming to IS 15658 -2006 of 60mm thickness, M-35 Grade laid over 40 mm thick sand cushning all as specified and directed.

Removing excavated material nexc. 50 metre and deposting where directed at a level nexc. 1.5 metre above the starting point all as specified and directed.

S&F powder coated aluminium section for doors, windows, ventilators door partition including fabrication of frame shutter and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clip and rubber beading for fixing glass panes in frame all as specified and directed. Note : (i) glass panes and wire mesh will be measured and paid separately. (ii) The quoted rate shall be inclusive of cost of rubber beading however it will be not be weighed and weighted paid separately. (iii) All other minor detals including cost of locking arrangement shall be included in the qquoted rate.

M&L 5.5 mm thick sheet glass, ordinary quality and glazing with aluminium beads and rubber gaskit in square exc 0.5 sqm in each pane frosted on one side all as specified and directed.

S&F aluminium alloy wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples all as specified and directed.

Material and labour for 15mm thick Ready Mix Plaster in single layer of make / brand - ACC's Accoplast / CK Birla's Aerocon /Ultra tech cement, mixed with liquid water proofing compound on other than fair faces of brick wall or concrete surfaces, (upto 05 storeys of bldgs) including use of scaffolding all as specified and directed. Note :- Liquid water proofing compound will be measured and paid seperately as supply only.

M&L for preparation of newly plastered surfaces of walls and applying two coats Oil bound distimper over a coat of birla putty (average 2 mm thick) all as specified and directed. Make :- Asian paint (Emulsion Sparc),Berger (Rangoli) or equivalent makes.

Excavation in trenches nexc 1.5 metre wide and nexc 1.5 metre deep for foundation and getting out in any type of soil all as specified and directed

M&L PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) in foundations,filling and mass concrete all as specified and directed.

M&L PCC 1:5:10 type E-2, (using 40mm graded crushed stone aggregate) with lean concrete/filling concrete in sunken portion all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in sub base to floor all as specified and directed.

M&L sand filling under floors or in foundations including watering and consolidation all as specified and directed.

M&L brick work with sub class 'B' Bricks straight or curved on plan exc 6m mean radius built in CM 1:6 all as specified and directed.

S&F joist, channel, angle, tee section or MS pipes fixed independently, without connecting plates, etc Fe-290(Gde E-165) (cut to ordinary lengths i.e. with in 20mm of the length indicated) all as specified and directed.

M&L rendering 15mm thick over concrete/brick surface in CM 1:6 all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash all as specified and directed.

S&F PVC door frame of size 50mm X 47mm made out of 5mm plain PVC sheet reinforced with MS tube all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the styles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing given in SSR part II 2004 all as specified and directed.

S&F hold fasts and similar small articles conforming to Fe 290 G-E-165 all as specified and directed.

M&L PCC(1:3:6) type C1 (using 20 mm graded crushed stone aggregate) as in bed blocks for hold fast including necesssary formwork all as specified and directed.

M&L two coats of syanthatic enamel paint over a coat of red oxide primer to steel surfaces including preparation of surfaces all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as specified and directed.

S&F PVC soil, waste and rain water (SWR) drainage pipes 110mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors all as specified and directed.

S&F PVC (SWR) bends 110mm radius all as specified and directed.

M&L RCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) in lintels including formwork all as specified and directed.

S&F 15 mm dia bib taps cast copper alloy with chromium plated cruch or butterfly handle scrwed, screwed for iron pipe or for brass ferrule and fixed all as specified and directed..

S&F 15 mm bore overhead shower single flow (ABS body chrome plated with grey face plate) with rubit cleaning system including shower arm 240 mm long (light weight) round shape with wall flange all as specified & directed.

S&F in repair 15 mm bore fancy type angular valve cast copper alloy screwed down, high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for unions all as specified and directed.

S&F in repairs 20 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe all as specified and directed.

S&F 5.50 mm thick frosted glass nexc 0.5 sqm in each pane fixed to aluminium frames all as specified and directed.

M&L broken stone boulder hardcore of gauge nexc 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and directed.

Returning filling in including spreading, levelling, watrering an well ramming in layers not exc 25 cm thick in soft/loose soil all as specified and directed.

M&L for cutting into existing manhole for connecting new drain, making good to pipe and rendering cutting existing benching for and forming branch channel in cement concrete 1:2:4 type B-1 smooth finish and reforming benching as required of 150mm dia pipe all as specified and directed.

M&L PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested of 150 mm bore of pipe all as specified and directed.

M&L salt glazed stoneware drain pipes laid in trenches and jointed as specified of 150mm dia all as specified and directed.

Material & Labour for providing precast cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in cover slabs for manholes/drains etc with plain fair faces including chamfers weathering throating and setting in CM (1:6) with joints to match all as specified and directed.

M&L Mild steel bar 6 to 8mm dia, cut to length bent to shape required, including cranking, bending spirally for hoping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality all as specified and directed.

S&F pulley operated clothes drying system consisting of anodized Aluminium pipes, each of outer dia 22 mm and inner dia 19.8 mm. Pulleys made up of delrin with rope guide mounted on channel pair of length 24” (distance between two pipes is adjustable). Locking system to hide rope knot. Channel to be mounted or fixed with self-tapping screws provided in kit. Rope will be polyester braided undyed of 4mm dia (For 9 feet) all as specified and directed.

S&F pulley operated clothes drying system consisting of anodized Aluminium pipes, each of outer dia 22 mm and inner dia 19.8 mm. Pulleys made up of delrin with rope guide mounted on channel pair of length 24” (distance between two pipes is adjustable). Locking system to hide rope knot. Channel to be mounted or fixed with self-tapping screws provided in kit. Rope will be polyester braided undyed of 4mm dia(For 6 feet) all as specified and directed.

Frends Enterprises

Unitech Enterprises

ASHOK CONSTRUCTION

Vandan Enterprises

Bidder Name

Unitech Enterprises

Frends Enterprises

ASHOK CONSTRUCTION

Vandan Enterprises

GANGAJAL