C.o Stadium at Shirgul Devta temple complex at Ghoond SH C.o Stag and steps for sitting in the Devta temple complex

Amount

Excavation in foundations, trenches etc., in earth work, lift upto 1.50 Metres stacking the eacavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15cm. layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 20 metres.

Providing and laying cement concrete 1:4:8 (One cement : Five sand : Ten graded/crushed stone aggregate 40mm (Forty millimetre) nominal size) mechanically mixed and curing complete excluding cost of form work in foundation and plinth including carriage of materials within all leads and lifts complete in all respect.

Providing form work with steel plates 3.15mm (Three point one five millimetre) thick welded with angle iron in frame 30x30x5mm (Thirty into thirty into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etcetra with wooden battens and ballies for all heights of propping and centering below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in

in foundation, footings bases of columns etcetera and mass concrete including carriage of materials within all leads and lifts and other incidentals complete in all respect.

in flat surface such as soffits of suspended floors, roofs, landings and the like upto any thickness including carriage of materials within all leads and lifts complete in all respect .

in vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttresses, plinth and string courses and the like including carriage of materials within all leads and lifts complete in all respect

in columns, pillars, posts and struts square, rectangular, polygonal in plan including carriage of materials within all leads and lifts complete in all respect .

in stair cases with slopping or stepped soffits, excluding landing but including carriage of material within all leads and lifts complete in all respect .

in beam, cantilever, girders and lintels, sides and soffits of beams beams haunching below supporting cantilevers girders bressumers and lintels of any depth in all height from floor including carriage of materials within all leads and lifts complete in all respect.

Providing and laying mechanically mixed and vibrated cement concrete 1:1½:3( 1cement:1½:sand: 3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form works and reinforcement for reinforced concrete work in

Foundations footings bases of clumns and the like and mass concrete including all leads and lifts, as per HP:PWD, specififation of 1990 Volume-I, as directed by the Engineer-In-Charge.

Suspended floors, roofs landing and shelves and their supports (i)upto floor two level.

Columns, pillars, posts and struts (i) Upto floor two level.

Stair cases with sloping orstepped soffits excluding landing.

Providing Mild steel/Tor steel reinforcement for R.C.C work including bending binding and placing in position complete upto floor two level (b) Tor Steel including all leads and lifts, as per HP:PWD, specififation of 1990 Volume-I, as directed by the Engineer-In-Charge.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

Boulder filling dry hand packed under floors including watering, ramming consolidation and dressing coplete.

Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortar 1:4 (1 Cement : 4 Sand) Second Class Bricks.

Brick work using common burnt clay building bricks in Super-structure above plinth levelupto floor two level (Second ClassBricks) in CM 1:4

Half brick masonry in common burnt clay building bricks in in Super-structure above plinth levelupto floor two level (Second ClassBricks) in CM 1:4.

Providing and fixing angle iron door frame manufacture from steel iron angle35x35x4mm welded with M.S flats 50x4x4mm including hinges jamb lock tails end if required angle thrashold or mild steel angle 50x25mm welded or rigidly fixed by mechanical means lugs with split and tail to each includign steel butt hinhes 2.5mm thick with provision of locking arrangements and shock absorbers as specified and applying a coat of approved steel primer and paint after pretreatment of surface including all leads and lifts, as per HP:PWD, specififation of 1990 Volume-I, as directed by the Engineer-In-Charge.

Providing and fixing flush door shutters interior grade, commercial type, core of black-board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains of cross bands andface veneers on both faces of shutters.35 mm thick including black enamelled M.S. butt hinges.

Providing and fixing steel glazed doors,windows and ventilators ofstanderd rolled steel sections,joints mitred and welded with16x3.15 mm lugs 10 cm.long embeddedin cement concrete blocks 15cmx10cmx10cm size of 1:3:6(1cement:3 sand:6 graded stoneaggregate 20mm nominal size)or withwooden plugs and screws or rawlplug and screws or with fixingclips or with bolts and nuts asrequired and ironfittings,including providing andfixing of glass panes with glazingclips and special metal sesh puttyof approvedmake complete includingapplying a priming coat of red leadpaint.

Fixed steel windows

side hung windows

Top hung ventilator

Providing & fixing steel wire gauge shutter in Z-section using MS wirebgauge of IS gauge desination 85g with wire of dia 0.56mm for door,window and clearstory window i/c metal beading of approved quality and shape section with necessary steel screw i/c applying a priming coat of red paint complete as per approved specification/design.

Providing and fixing Aluminium sliding door bolts anosdized colour and shade with bolts and nuts screws etc. complete including all leads and lifts, as per HP:PWD, specififation of 1990 Volume-I, as directed by the Engineer-In-Charge. 250x16mm.

Providing and fixing Aluminium tower bolts (barrel type) anodized transparent or dyed to required colour and shade with screws etc. complete including all leads and lifts, as per HP:PWD, specififation of 1990 Volume-I, as directed by the Engineer-In-Charge. 150x10mm.

Providing and fixing Aluminium handles anodized transparent or dyed to required colour of shade with necessary screws etc. complete including all leads and lifts, as per HP:PWD, specififation of 1990 Volume-I, as directed by the Engineer-In-Charge. 125mm.

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws. Plain grill .including carriage of material with in all leads and lifts

Cement concrete flooring 1:2:4 (1 cement: 2sand: 4 graded stone aggregate 20mm nominal size) laid in one layer finished with a floating coat of neat cement including all leads and lifts, as per HP:PWD, specififation of 1990 Volume-I, as directed by the Engineer-In-Charge.(a) 40mm thick

Cement plaster skirting (upto 30cm height) with cement morter 1:3 (1 cement:3 sand) finished with a floating coat of neat cement including rounding of junction with floor. 15 mm thick.

Kota stone slab flooring 20 mm (average) thick base of cement mortor 1:4 (1 cement :4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing and polishing complete. 25 mm thick.

Kota stone slab 25 mm thick in risers of steps,skirting dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement :3 sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing complete.

Providig pre-cast IRC fabric jali i/c fixing complete i/c carriage of materials with in all leads & lifts.

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mmnominal size with rammed and consolidated and grouted with fine sand including preparation of ground.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size)

Providing and laying heavy duty precast cement conrete inter locking paver blocks vibro compacted upto M- 50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for 60mm thick inter locking blocks

P/l 23cm dia half round stone pipe ware pipe in plinth protection to drain out the rain water etc. i/c carriage of material with in all leads and lift and as per the direction of Engineer-in-charge.

Providing and fixing 0.60mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves rd/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)

Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges.

Providing and fixing plain asbestos cement sheet ceiling of approved quality with butt jointing and wood screws (frame work and cover fillets to be measured and paid for separately) 6 mm thick.

Steel work welded in built up sections, trusses and framed work including cutting hoisting, fixing in position and applying a priming coat of lead paint in beans joints channels angles tees flats with connection plates or angle cleats as in main and cross beams, hip and jack rafters, purlins and connected to common rafters and the like as per specification of HP PWD, specification of 1990 Volume-I as per specification of Engineer-In-Charge.

In trusses & trussed purlins in building.

In gratings framed guard bars,ladders,railling,brackets and similar works.

6mm Cement plaster to ceiling (a) In Cement mortar 1:3(1Cement:3 Sand)

15mm Cement plaster in singlecoat on the rough side ofbrick/ concrete/stone wallsfor interior plastering uptofloor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm ingirth and finished even and smooth Cement Mortar 1:6 (1Cement:6 Sand).

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floortwo level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth Cement Mortar 1:6 (1 cement:6 sand).

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete with ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome.

Painting two coats (excluding priming coat)on new steel and other metal surface under coat with ready mixed paint brusing to give an even shade including cleaning the surface all dirt,dust and otherforeign matter with readymixed paint other than white

Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete with ready mixed priming paint brushing red lead,Red-oxide/zinc oxide chrome.

Painting two costs (excluding priming cost on new steel and other metal surfaces eith enamel paint brushin to give an even shade including cleaning the surface of all dirt,dust and other foregin matters with Enamel paint other than white

Providing and laying upto first floor two level reinforced cement concrete 1:2:4 (1 cement : 2 Sand : 4 graded stone aggregate 20mm nominal size) to give a smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement in string courses, copings, bed plates, anchor blocks, plain windows sills and the like :

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete. 150mm dia pipes

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete. PVC Plain bend 150mm dia

PVC Plain bend 150mm dia

PVC shoe 150mm dia

Naresh Kumar