Renovation and Interior Works for office space of REMCL at 8th Floor of PNB building at Bhikaji Cama Place, New Delhi

Amount

Total Amount of BoQ 2

Amount after unconditional Rebate

Description of Work / Item(s)

Amount

Total of BoQ 3, BoQ 4 and BoQ 5

Total Amount of BoQ3 (Item Rate)

Total Amount of BoQ4 (Percentage Rate)

Total Amount of BoQ5 (Percentage Rate)

Description of Work / Item(s)

Amount

Schedule - ( B ) Bill of Quantites for Interior Work (NS Items)

SUB HEAD -I - (CIVIL WORK)

NS 1 - Removing of glass panes ( any thickness or size) from metal frames etc ( ant thickness or size) hatching out old putty etc if any icluding stacking out serviceable and unserviceable material complete in all respects as per site requirement and as per directions of Engineer - in - Charge.

NS 2 - Supplying, fabricating and installation of Green wall consisting of MS frame steel structure including vertical wall panel 450 x 150 mm (apprx.) to hold 3 nos. of 150 mm pots, providing for drip irrigation with 12 mm / 16mm suitable irrigation pipe which is to be installed along with the drips for each pot with a filter. Pots would be installed with geotextile fabric filled with engineered soil consisting of cocopeat and vermicompost. 3 Nos. storage tanks with pressure pumps having capacity of 3000 Ltr each shall also be supplied and installed. Suitable plants will be supplied and planted as per client's choice. The rates includes all material and labour etc.complete in all respect as given in specification and as per direction of Engineer- In- Charge.

NS 3 - Grinding & Polishing existing marble / trezzo flooring complete in all respects including all tools and material required to complete the work in all repect as per site requirements complete in all respect as per direction of Engineer- In- Charge.

'NS 4 - Providing and fixing High performance Heat resistant toughened glass 6.00 mm thick of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shadingcoefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc with EPDM rubber / neoprene gasket etc and snap biding or glazzing clips with putty as per the site requirement complete in all respect as per direction of Engineer - in - charge.

NS 5 -Providing & Fixing decorative FILM Translucent including cost of Plotter cutting complete as per design approved by Engineer- In-charge .The work be executed in all respect as specification and as per direction of Engineer-in-charge.

NS 6 - Providing and fixing powder coated minimum thickness 50 micron aluminium tubular handle bar 32 mm outer dia,3.0 mm thick & 450 mm long with SS screws etc.complete in all respect as per direction of Engineer-in-Charge.

NS 7 - Providing and fixing aluminium expanded metal mesh 1.5 mm thick including all necessary hardware shall be fixed with all necessary fixtures and accessories including scaffolding complete in all respect as per site requirements and complete in all respect as given in specification and as per direction of Engineer- In- Charge.

NS 8 - Supplying & Installation of "Acoustic Movable Wall Partition system” consisting of 85 mm thick individually movable Acoustic Panels with 45db STL, suspended from a top track only, each panel to have top and bottom Spring Loaded operable seals operated by a crank handle. The panels must be inter-connected by means of a positive locking aluminium profile during closing. Each panel must be suspended on multi - directional roller. Panels must be constructed of a non- deflecting steel tube frame and aluminium profiles, bolted together. The frame must be clad either side with 16mm MDF panels. The panel must be filled with high density rock wool in accordance with the specified sound insulation requirements. The telescopic panel must open and close 120mm and must be operated by a single mechanism for both the top and bottom seals and for movement of the telescopic sleeve. The telescopic element must maintain all the same quality criteria as the other elements.complete in all respect as given in specification and as per direction of Engineer- In- Charge.

NS 9 - Providing and laying 12 mm thick laminate wooden flooring ( AC5) with double locking system on 3mm thick foam for noise reduction. Wooden planks having mehlamine impregnated decorative film of HDF density (water & fireresistant) to be laid complete in all respect as given in specification and as per direction of Engineer- In- Charge.

NS 10 - Providing & fixing horizontal level suspended ceiling comprising of Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade 6063 T5. The baffle blade shall be in size of 100x25x3600mm in powder coated to Woodgrain/Plain finish (Red Oak, Cherry, Black / White). The baffle shall be electrostatically polyester powder coated to a coating thickness of 60-80 micron. The powder coating shall pass Salt Spray Test for 750 Hours as per ASTM B117, QUV–A Test for 1000hours as per ASTM G-154 – (Cycle – 1) and Humidity test for 1000hours as per DIN 50017. The powder coating shall have an adhesion of GT0 as per EN ISO 2409. The shade variation within a manufacturing batch shall be delta E<1 using Excite/BYK Gardner instrument and gloss level 25±5% at 60˚ as per ASTM D523 (Not applicable of Wood Grain Shade). The baffle blade shall be suspended using Slotted U-profile of 20 x 30 x 3700mm (Thk-1.5mm) having slots in module of 25mm to keep baffles at an on-center spacing of 100mm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with End caps.

(i) SUSPENSION: Shall be hanged using baffle hanger from U-profile made of mild steel with powder coating thickness of 60-80 micron. The U – profile to comprise of alternate square & rectangular slots of 6.5x6.5mm & 28x6.5mm respectively on the web for locking the baffle hanger using plugin clip to secure the hanger in perfect position and achieve uniform spacing between baffles. The overall dimension of the U – profile is 20(W) x 30(H) x 3750(L) mm and is rolled form from 1.5mm thick mild steel with a powder coating thickness of 60-80micron. U- Profile to be connected to each other using U –Profile Splice. The U- profile shall be hanged from the true ceiling using threaded rod using a U- Profile hanger.

(ii) INSTALLATION: To comprise main runner spaced at 1200mm securely fixed to the structural soffit using suspension system (specifications below) at 1200mm maximum. The First/Last suspension system at the end of each main runner shall not be greater than 450mm from the adjacent wall along with the first and the last main beam shall be at less than 600mm from the wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls using screws at 450mm centre to centre maximum.Installation shall be carried out as per Manufacturer recommended procedure.complete in all respect as given in specification and as per direction of Engineer- In- Charge.

NS 11 - Providing & Fixing of Fibre Glass Acoustical Suspended Ceiling System with 20/25mm thick Microlook 90 Edge Tiles with 15mm Bolt Slot exposed grid.The tiles shall have smooth laminated visual with Humidity Resistance (RH) of 95%, NRC 0.9 -1.0(Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, , Light Reflectance ≥85% as per ASTM E-1477, Colour Pebble White, Fire Performance of Class 0/1 as per BS 476 Part 6/7 with 15mm Square Tegular/Microlook 90˚ edge and 8mm drop in module size of 600 x 600mm. It shall be suitable for Green Building application, with Recycled content of 66% (GW)/ 74% (RW).

(i) SUSPENSION: The tile shall be laid on grid system with 15mm white flanges incorporating a 6mm central reveal in white/black colour with mitred ends & “bird’s mouth” notches to provide mitred cruciform junctions colour global white. Grid shall have double stroke rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 7.9 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 9.5 kg/m. The end details of the cross tee shall be made of pre hardened steel clip fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. All main beam to main beam and cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T Sections shall be made of 90 gsm as per IS 277 (2003) pre- painted steel with baked polyester paint of 0T bending capability. The Tile & Grid system used together shall carry a 10 year warranty against manufacturing defect and manufacturer shall provide a warranty certificate. The Tile & Grid shall have the manufacturers name embossed/printed on it. The supply shall be backed by a Manufacturing Test Certificate.

(ii) INSTALLATION: To comprise main runner spaced at 1200mm securely fixed to the structural soffit using suspension system (specifications below) at 1200mm maximum. The First/Last suspension system at the end of each main runner shall not be greater than 450mm from the adjacent wall along with the first and the last main beam shall be at less than 600mm from the wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees.Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls using screws at 450mm centre to centre maximum. Installation shall be carried out as per Manufacturer recommended procedure. complete in all respect as given in specification and as per direction of Engineer- In- Charge.

NS 12- Providing and Fixing Channelled perforated panels of width 192mm, thickness of 15mm and length 2400 mm, made of a Moisture resistant fibre board substrate with a laminated facing as per the approved shade (Portland Maple, Sea Beech, Siam Wood & Mystique Walnut, Interior White, Alumina Pearl) and a melamine balancing layer on the reverse side. The boards shall have a special perforation pattern where the reverse surface has a “Helmholtz” fluted perforation with consecutive 3mm wide groove followed by 13mm of visible pane. The edges of the panel shall be “tongue- and-grooved” to fix special clips for installation and seamless visual. The back of the perforated panel shall have sound absorbing non-woven Soundtex acoustical fleece hot pressed to achieve NRC of 0.6. (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 and Humidity Resistance (RH) of 70% with camber limit less than 1mm/1000mm and bow less than 1mm/300mm.The panels shall be mounted on special aluminium splines (keel) using inside clips provided by Manufacturer and complete in all respect as per direction of Engineer- In- Charge.

(i) The panel shall be mounted by tongue and groove mechanism using inside clip on aluminium extruded keel made of Grade 6063-T5 having dimensions 3000(L) x 24(H) x 15.5(W).The keel shall also be used for transition of the butt end of adjacent panel at every 7.2m. The Panel, Keel system used together shall carry a 1 year warranty against manufacturing defect and Manufacturer shall provide a warranty certificate. The supply shall be backed by a Manufacturing Test Certificate.

(ii) INSTALLATION: An appropriate vapour barrier (by others) shall be applied/installed on the vertical surface before the installation to properly seal against entry of any moisture. Vapour barrier (by others) shall be installed as per Manufacturer’s recommendation. Install wooden batten grid (provided by others) of section 50x50mm or as approved by the Architect on the solid wall/partition to provide level and plumb surface for fixing Keel. Install Keel vertically using screws and plugs at spacing of not more than 600mm centre-to-centre. The first and last keel should not be more than 150mm from the ends. Trim the tongue of the first bottom panel and install using headless nail with groove side upward. Subsequent panels are installed with tongue side downward by engaging with each other using tongue and groove mechanism and secured by inside clip. Continue this process until required height is achieved. Shorter butt edges need to be joined using industrial/wood glue. The keel shall also be used for transition of the butt end of adjacent panel at every 7.2m. Install the Skirting (provided by others) of width 50mm or more as required by the Architect/ Engineer-in Charge. Finish off the edges using wooden moulding of matching colour (by others). Installation should be carried out as per Manufacturer recommended procedure.complete in all respect as given in specification and as per direction of Engineer- In- Charge.

NS 13 - AcousticProviding and Fixing of Acoustical Wall Panel with square edges made of fibre glass substrate 25mm thick, wrapped on the front side with an acoustically transparent fabric as per the approved shade (Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell). The panel shall be classified for Fire Class A, as per ASTM E-84. The Acoustical Wall Panel shall be of sizes 600x600mm (Nominal) or 600x1200mm (Nominal) and shall achieve an NRC of 0.85 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) with 50mm airgap as per ASTM C423 to be fixed to wall on a framework of wooden battens and using Wall panel Impalers (supplied by the manufacturer) or by using construction adhesives (as per the instructions laid down by the manufacturer). The fibre glass al wall panel.

(i) An appropriate vapour barrier (by others) shall be applied/installed on the vertical surface before the installation to properly seal against entry of any moisture. Vapour barrier (by others) shall be installed as per Manufacturer’s recommendation. Install wooden batten grid (provided by others) of section 50x50mm or as approved by the Architect on the solid wall/partition to provide level and plumb surface. The Impalers shall be fixed to the battens using self-tapping screws, 3 nos. in case of 600x600mm and 4 nos. in case of 600x1200mm. Silica based construction adhesive (by others) to be dabbed on to the projecting elements (spikes) of the Impalers. Wall Panels shall be pierced through the spikes of the Impalers ensuring the line and level of the panels are maintained. complete in all respect as per direction of Engineer- In- Charge.

NS 14 - MOTORISED TRIPLE BLINDS Providing and fixing Motorised Triple Blinds with PELMET motorised system automatically locked on release of ball chain. Plastic idler plug roller tuhes corrosion proof outside dia 38mm , bottom rail stiffening element , ball chain acetel balls endless, Fabric 100% Polyester with width of 2.60 Mtr & vane size 2"complete as per directions and entire satisfaction of Engineer-in-Charge (Automation Using Somfy RTS Motors with an average of 1motor for 12sqm of blind area )Make-Hunter,Dougles,Wintree.complete in all respect as given in specification and as per direction of Engineer- In- Charge.

NS 15 - Providing & Fixing of make Single glazed modular system consist of Al. section of 25*40*2.5 mm thick. All sections duly anodized up to 15-20 microns with 6063-T6 grade and required accessories ie glass to glass aluminum I sections, T section & 90 degree sections & Glass packing to adjust the floor level. Ceiling profile, Floor profile and wall profile are 25 mm visible face and 25 mm wide with 10mm toughen glass & insertion of silicon gasket to adhere the glass firm & airtight. Profile Make – Otic/ Droma Crowm/ Assaabloy.Glass make -- Saint Gobain/ Ashahi/ Pilkington.complete in all respect as given in specification and as per direction of Engineer- In- Charge.

NS 16 - Providing & Fixing of make Single glazed modular system consist of Al. section of 25*40*2.5 mm thick. All sections duly anodized up to 15-20 microns with 6063-T6 grade and required accessories ie glass to glass aluminum I sections, T section & 90 degree sections & Glass packing to adjust the floor level. Ceiling profile, Floor profile and wall profile are 25 mm visible face and 25 mm wide with 12mm MDF Board both side laminated & insertion of silicon gasket to adhere the glass firm & airtight. Profile Make – Otic.Vectro//Dorma crown/Assaabloy.complete in all respect as given in specification and as per direction of Engineer- In- Charge.

NS 17 - Providing and fixing of Glass Door 12mm thick Toughened Glass Door of size- 2.10mX1m with Floor Spring Machine of load carrying capacity 60-80kg with D Handle Centre Spacing 300mmMake-Otic/Dorma crown/Assaabloy. Glass Make-Saint Gobin /Dorma /Ashahi and spring machine complete in all respect as given in specification and as per direction of Engineer- In- Charge.

SUB HEAD - II - (PLUMBING WORK)

NS 18 - Providing and fixing white vitreous china one piece Floor mounting water closet of size735x 367x750mm S-trap: 305mm cistern with dual flush fitting, of flushing capacity 3 litre/4.8 litre including seat cover, and cistern fittings, nuts, bolts and gasket etc complete. Make-Kohler, Model NO. 3902IN-S-0, or equivillent Toto, Laufen. complete in all respect as per direction of Engineer- In- Charge.

NS 19 -Providing and fixing table top round wash basin, Wall mounted basin mixer with smooth body and flexible supply connection standard pattern including painting of fittings and brackets, , grid drain, versatile concealed inwall valve cutting and making good the walls wherever require: make Kohler Model No. 14800T-0, Basin mixer, Kohler model no- 5683IN-4ND-CP, Concealed valve Make kohler model no. 5679IN-CP or equvillent Grohe, Laufen. complete in all respect as per direction of Engineer- In- Charge.

NS 20 - Providing and fixing ABS Chrome plated Hand Shower (Health Faucet) with 8 mm dia, 1 Meter long Flexible tube in chrome & wall hook including cutting and making good the walls wherever required complete as per instructions of the engineer-in-charge (Kohler model no 98100IN-CP or equivalent grohe, Schell and as per approved list of make). complete in all respect as per direction of Engineer- In- Charge.

NS 21 - Providing and Fixing C.P. brass Sink mixer with Swinging Casted spout & connecting legs and flanges, including cutting and making good the walls wherever required (Jaquar model no CON-309KNB or equivalent Kohler, Roca as per approved list of make. complete in all respect as per direction of Engineer- In- Charge.

NS 22 - Supplying, Installation, Testing and Commissioning of five star rated vertical / horizontal storage type hot water heater fixed to wall with anchor bolts & nuts all complete work, (for kitchen, pantry), (Jaquar model no ELENA or equivalent A.O. Smith, Havells as per approved list of make). complete in all respect as per direction of Engineer- In- Charge.

'NS 22.1 - Capacity 25 lit.

'NS 23 - Providing and Fixing CP towel ring complete with brackets fixed to stainless steel with CP brass screws with concealed fitting arangement of approved quality colour and make (Jaquar model no ACN-1121N or equivalent Kohler, Roca as per approved list of make).complete in all respect as per direction of Engineer- In- Charge.

'NS 24 - Providing and Fixing Toilet paper Dispenser with stainless steel and C.P. brass screws including cutting and making good the wall wherever required. (Jaquar model no PTD-SAP-DT0106CS). complete in all respect as per direction of Engineer- In- Charge.

'NS 25 - Providing and fixing liquid soap Dispenser capacity of 0.8ltr with push button fixed in stainless steel and C.P. brass screws including cutting and making good the wall wherever required. (Jaquar model no SDR-WHT-DJ0010F). complete in all respect as per direction of Engineer- In- Charge.

'NS 26 - Providing and fixing 125mm grating with ring and S.S anti cockroach trap down to the ring with s/s screws and embedding and setting ring into the floor with cement mortar .(Cockroach trap Vijay Make Model no. ADS-1286, C.P. grating model no. ads-1262 or equivalent Chilly, sanjay chilly or approved list of make). complete in all respect as per direction of Engineer- In- Charge.

NS 27 - Providing and fixing G.I. Inlet fittings with maximum 3 inlets 32,40 & 50 mm size fabricated from 100 mm dia G.I.pipes and welded G.I. sockets, fixed to C.I. Trap and set in cement concrete as per drawing. complete in all respect as per direction of Engineer- In- Charge.

NS 28 - Providing and fixing cast brass cleanout plug with suitable insert keys for opening, male threaded joint with G.I. socket caulked to spun soil pipe including cost of lead joint etc. complete. .(Brass Clean out plug Vijay Make Model no. 1216A, C.P. grating model no. ADS-1262 or equivalent Chilly, sanjay chilly or approved list of make). complete in all respect as per direction of Engineer- In- Charge.

NS 29 - Providing and Fixing CP Grating with frame 5" and 2 SS Screws casted heavy duty 125 mm dia including cutting and making good the walls and floors wherever required complete in all respects . Vijay Make C.P. grating Model no. ADS-1262 or equivalent Chilly, sanjay chilly or approved list of make). complete in all respect as per direction of Engineer- In- Charge.

NS 30 - Providing and Fixing G.I. Reducing elbow of 100 x 50 mm in cement concrete 1:2:4 at all levels for floor drains (exlcuding cost of grating) for connection to floor traps in sunken portions, complete as per drawings and as per approval of the engineer-in-charge.(GI Pipe for connecting elbow with floor trap shall be measured seperatly ). complete in all respect as per direction of Engineer- In- Charge.

NS 31 - Providing, fixing, testing and commissioning of CP brass two way bib cock of approved make. (Jaquar model no KUB-35041F or equivalent Kohler, Roca as per approved list of make). complete in all respect as per direction of Engineer- In- Charge.

SUB HEAD - III - (FIRE EXTINGUISHERS)

NS 32 - Providing and fixing fire extinguisher of carbon dioxide type consisting of brand new high pressure steel cylinder bearing IS: 7285 mark and having the approval of controller of explosives Nagpur, wheel type valve bearing IS:3224 mark internal discharge tube, 1 meter long high pressure discharge hose, non conducting horn, suspension bracket, fully charged bearing IS: making fixed to wall as directed conforming IS : 15683:2006. complete in all respect as per direction of Engineer- In- Charge.

(i) NS 32.1 -4.5kg capacity cylinder

(ii) NS 32.2 -22.5 kg (Trolly Mounted)

NS 33 -Providing and fixing water based CO2 type extinguishers consisting of welded M.S. cylindrical body, squeeze lever discharge valve 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket, ISI marked as per IS:934 finished externally with red enamel paint and fixed to wall with brackets complete with internal charges. complete in all respect as per direction of Engineer- In- Charge.

NS 33.1 -Capacity 9 KG

NS 34 -Providing and fixing ISI marked portable fire extinguishers of the following type. complete in all respect as per direction of Engineer- In- Charge.

NS 34.1 -Dry Chemical Powder ABC type of 6 Kg as per IS:15683

SUB HEAD - IV - (FURNITURE)

NS 35 - Providing & placing Main desk size shall be : 2400 Width mm x 1104 Depth mm x 735 Height mm.The top panel shall be 40 mm thick(18 mm MDF + 18 mm MDF batons + 4 mm Natural Veneer) Veneered portion of work surface is finished with high gloss polyster.The understructure shall be having legs made from 1.6 mm thick MS clad with the strips of MFC (Medium Density fiber).Hollow construction of legs facilitates wire management .The modesty & side panel should be 18 mm thick MDF plus pigmented black and coated with melamine. The storage shall be having drawer unit unit body shall be constructed from 18 mm thick MDF boards has combination of 2 box drawers + 1 filling drawer . Drawers should be mounted on double extension ball slides + drawer fronts should be of natural veneer coated with High gloss Polyster and made of 23 mm (18 mm MDF + 4 mm Natural Veneer + 1 mm DL) and drawer body made of 14 mm MDF (12 mm MDF + 1 mm DL + 1 mm DL). ERU LHS size shall be : 1400 Width mm x 580 Depth mm x 690 Heightmm. The top panel shall be 40 mm thick(18 mm MDF + 18 mm MDF batons + 4 mm Natural Veneer) Veneered portion of work surface is finished with high gloss polyster.The understructure shall be having the modesty panel of 18 mm thick MDF plus pigmented black and coated with melamine. The storage shall be having drawer unit unit body shall be constructed from 18 mm thick MDF boards has combination of 2 box drawers + 1 filling drawer . Drawers should be mounted on double extension ball slides + drawer fronts should be of natural veneer coated with High gloss Polyster and made of 23 mm (18 mm MDF + 4 mm Natural Veneer + 1 mm DL) and drawer body made of 14 mm MDF (12 mm MDF + 1 mm DL + 1 mm DL). complete in all respect as per direction of Engineer- In- Charge.

NS 36 - Providing & placing Back unit size shall be of : 1860 Width mm x 580 Depth mm x 690 Height mm. The door shall be 23 mm thick ( 18 mm thick Batons + 4 mm Veneer + 1 mm Backing Decorated ( BDL) ) . The Shelves and Partitions should be of 18 mm thick MDF ( Medium density fiber) + Pigmented Black and coated with Melamine. complete in all respect as per direction of Engineer- In- Charge.

'NS 37 - Providing and placing the very high back leather chair whose The seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed plywood & upholstered with leather and moulded polyurethane foam. The back shall be designed with contoured lumber support for extra comfort. Size of back shall be W-53cm, H-95.4cm & size of seat shall be W- 54.6cm x D-49cm. High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The seat and back should be arrested together with spine made of 0.8 +/- 0.05 cm thick HR steel and should be powder coated in black with 40-60 micron DFT (Dry film thickness). The armrest assembly should be made up of armrest tube, PU armrest and the armrest top. The armrest tube assy. shall be made of 2.54+/- 0.03cm x 0.16 +/- 0.0128 cm M.S E.R.W support tubes and chrome plated. The P.U armrest shall be made up of black integral skin polyurethane with 50-70 shore 'A' hardness reinforced with M.S insert. The armrest top shall be made up of ABS & upholstered with foam & leather. It shsall have front Pivot synchro tilt mechanism. The mechanism of the chair shall have following features : 360⁰ revolving type, Knee Tilt system, Seat & back tilting ration of 1: 1.5, Front pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 5-position locking with antilock back mechanism which should prevent the backrest from impacting the user when the lock is released, Static seat depth adjustment 5.0 +/- 0.5cm with 5 position locking.

(i)The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0+/- 0.3 cm. The bellow should be single piece duly blow moulded in black polypropylene. The pedestal shall be made of die-cast aluminium with buffing finish. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 67.0 +/- 0.5 cm pitch-centre-dia (77.0 +/- 1.0 cm with castors). The twin wheel castors shall be made of Nylon injection moulded in black color. Overall dimensions of Chair shall be, Width of Chair - 77cm, Depth of Chair - 77 cm as measured from pedestal below. Height of back from ground - min 128.0 to max 137.0 cms. Seat height - min 49.9cm to max 58.9 cm. Dimensions tolerance / variations shall be within +/- 1 cm. complete in all respect as per direction of Engineer- In- Charge.

'NS 38 - Providing and placing revolving visitor chair whose seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed plywood & upholstered with leather and moulded polyurethane foam. The back shall be designed with contoured lumber support for extra comfort. Size of back shall be W-53cm, H-73cm & size of seat shall be W-54.6cm x D-49cm. High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The seat and back should be arrested together with spine made of 0.8 +/- 0.05 cm thick HR steel and should be powder coated in black with 40-60 micron DFT (Dry film thickness). The armrest assembly should be made up of armrest tube, PU armrest and the armrest top. The armrest tube assy. shall be made of 2.54+/- 0.03cm x 0.16 +/- 0.0128 cm M.S E.R.W support tubes and chrome plated. The P.U armrest shall be made up of black integral skin polyurethane with 50-70 shore 'A' hardness reinforced with M.S insert. The armrest top shall be made up of ABS & upholstered with foam & leather.

'(i)The mechanism of the chair shall have following features : 360⁰ revolving type without back tilt. The chair shall be provided with pneumatic height adjustment which shall have stroke of 12.0 +/- 0.3 cm. The beloow should be made up of 3 piece telescopic type & injection moulded in black polypropylene. The pedestal shall be made of die-cast aluminium with buffing finish. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 67.0 +/-0.5 cm pitch-centre-dia (77.0 +/- 1.0 cm with castors). The twin wheel castors shall be made of Nylon injection moulded in black color. Overall dimensions of Chair shall be, Width of Chair - 77cm, Depth of Chair - 77 cm as measured from pedestal below. Height of back from ground - min 99.4 to max 111.4 cms. Seat height - min 43.4cm to max 55.4 cm. Dimensions tolerance / variations shall be within +/- 1 cm. complete in all respect as per direction of Engineer- In- Charge.

NS 39 - Providing and placing 3 seater sofa whose overall dimension shall be 1960mm (L) X 920mm (W) X 950mm (H). PVC upholstery shall be dust resistant. Armrest shall be made of rubberwood. Leg material shall be pine wood. Belt material shall be high flexibility ribber. complete in all respect as per direction of Engineer- In- Charge.

'NS 40 - Providing and placing 1 seater sofa whose overall dimension shall be 1020mm (L) X 920mm (W) X 950mm (H). PVC upholstery shall be dust resistant. Armrest shall be made of rubberwood. Leg material shall be pine wood. Belt material shall be high flexibility ribber.complete in all respect as per direction of Engineer- In- Charge.

'NS 41 - Providing & placing in position table with sizes 1000 W X 600 D X 428 H mm with top made in 10mm tempered glass supported with an understructure of MDF & finished with paper laminate. Lower shelf shall be made of MS CRCA steel with epoxy polyester powder coating. The work shall be carried out as per the instructions received from engineer in charge.

NS 42 - Providing and placing 8 Seater table whose size shall be 2400 Width mm x 1200 Depth mm x 750 Height mm . Top shall be 32 mm thick Base material shall be 18 + 12 mm MDF board. There shall be natural veneer 0.5 mm on top surface plus 0.6 mm balancing laminate on bottom surface Chamfer edges - PU Matt painted and veneer portion of worksurface is finished in PU Matt paint . The Veil and cross member shall be 18 mm thick base material shall be 16 mm plain particle board plus post - laminated work -surface with 0.6 mm laminate on eithe side . 2 mm thick and 0.8 mm thick PVC edge banding of matching colour on outer edges of Veil 0.8 mm thick PVC edge banding of matching colour on outer edges of cross member . The legs shall be made from 1.6 mm Matt silver Anodized Aluminium extrusion . Legs assembeled together with a plastic glide holder at bottom and 5 mm thick MS powder coated sheet at top . The plastic glide holder is having provision for wire entry and glide fixing . The wire carrying is facilited through the hollow space between two leg extrusions and the wires are concealed between removable rigid PVC extrusion in the leg . Access Flap and Switch Mounting Tray shall be made of matt silver anodized aluminium extrusion and plastic moulded components . Powder coated switch mounting tray made from 0.8 mm and 1.2 mm MS sheet .Switches to be mounted on tray as per requirement and Provision for mounting a module anchor roma swtch plate on switch mounting tray. complete in all respect as per direction of Engineer- In- Charge.

NS 43 - Providing and placing mid back chair whose seat shall be made up of 1.2+/-0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded polyurethane foam. The back shall be made up 1.2+/- 0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The moulded polyurethane foam shall be of density 45+/-2kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression. The dimensions of seat shall be- 51.0cm(W) x 48.0cm(D) and of back shall be 48.0cm(W) x 64.5Cm(H). The armrest top shall be made of moulded polyurethane and mounted on to a drop lift height adjustable type M.S tubular armrest support chrome plated. The armrest height shall be adjustable up to 6.5+/-0.5cm in 5 steps and also has swivel adjustment of 22 degree+/-2 on both sides. The mechanism of the chair shall have following features : 360⁰ revolving type, Knee tilt synchro mechanism, Tilt tension adjustment, Single point control, 4 position locking with anti shock feature, Seat/Back tilting ratio of 1:2. Seat depth adjustment of 6.0+/-0.5cm should be locked in 6 positions. complete in all respect as per direction of Engineer- In- Charge.

(i) The backrest shall consists of a sliding up down mechanism, Which can be adjusted in the range of 7.5+/-0.5cm and should be locked in 4 positions for correct position of lumber support.The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm. The pedestial shall be fabricated from 0.2+/-0.02cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap. The size of the pedestal shall be 66.0+/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with castors). The twin wheel castors shall be made black nylon. Overall dimensions of Chair shall be, Width of Chair - 76.0cm, Depth of Chair - 76.0cm as measured from pedestal below. Height from ground - min 89.0 to max 105.0cm. Seat height - min 46.9 to max 55.9cm. Dimensions tolerance / variations shall be within +/- 1 cm. complete in all respect as per direction of Engineer- In- Charge.

NS 44 - Providing and placing the main table shall be of size 2400 Width mm x 900 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front modesty panel of the table shall be made up of MDF board of size 2240 mm x 600 mm x 16mm which shall also be duly finished with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF board duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be 25mm. complete in all respect as per direction of Engineer- In- Charge.

'NS 45 - Providing and placing the Back unit whose size shall be 2215mm width x 410 mm Depth x 2000mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. Below storage shall be provided with wooden shutters & the upper left & right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H. complete in all respect as per direction of Engineer- In- Charge.

NS 46 - Providing and placing the high back chair whose seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed moulded reconstituted wood & upholstered with leather and moulded polyurethane foam. Size of back shall be (W)-46.0cm, (H)-57.0cm & size of seat shall be (W)-49.0cm x (D)-49.5cm. High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The back rest should be connected to the mechanism with a drop-lift mechanism which can be adjusted in the range of 7.0+/-0.5cm for the comfortable back support to suitable individual need. Armrests should be pressure die casted in polished aluminium with PP arm tops. The mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:3, Synchronized tilt, Back tilt with 4 position locking and Side tilt tension adjustment knob should be operated while taking back support for better adjustment of comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of head rest shall be (W)26.0cm x 12.0cm(L). The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/-1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 113.5 to max 138.0 cms. Seat height - min 41.0cm to max 51.0 cm. Dimensions tolerance / variations shall be within +/- 1 cm. complete in all respect as per direction of Engineer- In- Charge.

NS 47 - Providing and placing miod back chair whose seat shall be made up of 1.2 +/- 0.1 cm thick hot pressed moulded reconstituted wood & upholstered with leather and moulded polyurethane foam. The back shall be designed with contoured lumber support for extra comfort. Size of back shall be (W)-45.0cm, (H)-49.0cm & size of seat shall be (W)-49.0cm x (D)-49.5cm. High Resilience (HR) foam should be used in making seat & back which shall be moulded with density 45 +/- 2 kg/m ³ and hardness load 16+/- 2 kgf as per IS: 7888 for 25% compression. The back rest should be connected to the mechanism with a drop-lift mechanism which can be adjusted in the range of 7.0+/- 0.5cm for the comfortable back support to suitable individual need. Armrests should be pressure die casted in polished aluminium with PP arm tops. The mechanism of chair shall have following features:360 degree revolving type, Seat/Back tilt ratio of 1:3, Synchronized tilt, Back tilt with 4 position locking and Side tilt tension adjustment knob should be operated while taking back support for better adjustment of comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall be made of die- cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black polypropylene. Overall dimensions of Chair shall be, Width of Chair - 75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 93.5 to max 110.5 cm. Seat height - min 41.0cm to max 51.0 cm. Dimensions tolerance / variations shall be within +/- 1 cm. complete in all respect as per direction of Engineer- In- Charge.

'NS 48 - Providing and placing 3 seater sofa whose overall dimension of the sofa shall be (L)1820mm*(H)890mm*(W)920mm. Upholstery shall be of synthetic leather. Round and soft edges shall be there for safetyThread used shall be of Nylon. Material Handling Data Sheet (MSDS) for Glue Standard of Plywood used: IS 303 Commercial Plywood Thickness 12mm. complete in all respect as per direction of Engineer- In- Charge.

'NS 49 - Providing and placing 1 seater sofa whose overall dimension of the sofa shall be (L)920mm*(H)890mm*(W)920mm. Upholstery shall be of synthetic leather. Round and soft edges shall be there for safetyThread used shall be of Nylon. Material Handling Data Sheet (MSDS) for Glue Standard of Plywood used: IS 303 Commercial Plywood Thickness 12mm. complete in all respect as per direction of Engineer- In- Charge.

'NS 50 - Providing & placing in position table with sizes 1000 W X 600 D X 428 H mm with top made in 10mm tempered glass supported with an understructure of MDF & finished with paper laminate. Lower shelf shall be made of MS CRCA steel with epoxy polyester powder coating. The work shall be carried out as per the instructions received from engineer in charge.

'NS 51 - Providing and placing 8 Seater conference table whose size shall be 2400 Width mm x 1200 Depth mm x 750 Height mm . Top shall be 32 mm thick base material shall be 18 plus 12 mm MDF board 0.4 mm PVC membrane foil using wrap around technology . The foil is pre- coated with PU layer for better scratch and wear resistant plus 0.6 mm balancing laminate on bottom surface . The veil and cross member shall be 18 mm thick base material shall be 16 mm plain particle board post laminated with 0.6 mm top laminate on either side plus 2 mm thick and 0.8 mm thick PVC edge banding . The legs shall be made from 1.6 mm matt silver anodized aluminium extrusion .Legs assembeled together with a plastic glide holder at bottom and 5 mm thick MS powder coated sheet at top . Also there shall be accessflap and switch mounting tray made from matt anodized aluminium extrusion . complete in all respect as per direction of Engineer- In- Charge.

'NS 52 - Providing and placing mid back chair whose seat shall be made up of 1.2+/-0.1cm thick hot pressed plywood and upholstered with fabric or synthetic leather and moulded polyurethane foam. The back shall be made up 1.2+/- 0.1cm thick hot pressed plywood upholstered with replaceable fabric or synthetic leather upholstery covers and moulded polyurethane foam. The moulded polyurethane foam shall be of density 45+/-2kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression. The dimensions of seat shall be- 51.0cm(W) x 48.0cm(D) and of back shall be 48.0cm(W) x 64.5Cm(H). The armrest top shall be made of moulded polyurethane and mounted on to a drop lift height adjustable type M.S tubular armrest support chrome plated. The armrest height shall be adjustable up to 6.5+/-0.5cm in 5 steps and also has swivel adjustment of 22 degree+/-2 on both sides. The mechanism of the chair shall have following features : 360⁰ revolving type, Knee tilt synchro mechanism, Tilt tension adjustment, Single point control, 4 position locking with anti shock feature, Seat/Back tilting ratio of 1:2. Seat depth adjustment of 6.0+/-0.5cm should be locked in 6 positions. The backrest shall consists of a sliding up down mechanism, Which can be adjusted in the range of 7.5+/-0.5cm and should be locked in 4 positions for correct position of lumber support.The chair shall be provided with pneumatic height adjustment which shall have stroke of 9.0 +/- 0.3 cm.

'The pedestial shall be fabricated from 0.2+/-0.02cm thick HR sheet, chrome plated and assembled with injection moulded black polypropylene hub cap. The size of the pedestal shall be 66.0+/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with castors). The twin wheel castors shall be made black nylon. Overall dimensions of Chair shall be, Width of Chair - 76.0cm, Depth of Chair - 76.0cm as measured from pedestal below. Height from ground - min 89.0 to max 105.0cm. Seat height - min 46.9 to max 55.9cm. Dimensions tolerance / variations shall be within +/- 1 cm. complete in all respect as per direction of Engineer- In- Charge.

'NS 53 - Providing and Placing of Table. Overall Size of the MAIN TABLE 2100 x 1050 x 750. Primary Work Surface Made of 25mm thick MDF one side pre-laminate board with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire Management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Understructure Made of 25mm Thick Pre-laminated twin board, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board , Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security. overall size: 2100x2250x750. complete in all respect as per direction of Engineer- In- Charge.

'NS 54 - Providing & Placing Back unit whose overall dimension shall be 1800mm (W) X 500mm (D) X 1150mm (H). Top panel shall be Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top.Back unit slide door unit shall be Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirmingtoIS-12823:1990,Edge banded with matching 2mm thick PVC lipping for bodypanels likes ide,bottom,back and shelves.Shutters shall be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security. complete in all respect as per direction of Engineer- In- Charge.

NS 55 - Providing and Placing of chairs of following specifications. The seat is made up of 1.4cm thick hot pressed plywood, moulded polyurethane foam and upholstered with fabric. Seat size shall be 50cm x 49cm. Back assembly shall be upholstered with Mesh fabric and is made of back outer injection moulded in glass filled Polyamide and back inner injection moulded in glass filled Polypropylene. The back consist of adjustable lumbar support made of injection moulded PolyOxyMethylene (POM) which is upholstered with foam and fabric having adjustment of 5.5cm. Back size shall be 48cm x 54.5cm. Polyurethane foam shall have density= 55 kg/m3. Four way adjustable armrest shall be made from Glass filled polyamide with PU armtop and height adjustment of 9cm. The armtop has swivel, side to side and to-fro movement. It shall have Auto Balance synchr Tilt mechanism and shall be 360° revolving type and 4 position giving option of variable tilt angle to the chair. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 4.5cm. The headrest is made of injection moulded in glass filled polyamide, foam and upholstered with fabric. It has adjustment of 5cm. The class 4 pneumatic height adjustment has stroke of 9.5cm. The pedestal is injection moulded in glass filled Polyamide and fitted with 5 nos. twin wheel castors. The Pedestal diameter is 67cm. Twin wheel castors are injection moulded in Polyamide with 6cm diameter. The overall dimensions of the chair shall be 780mm x 780mm x (1130mm - 1260mm). complete in all respect as per direction of Engineer- In- Charge.

'NS 56 - Providing and placing mesh back visitor chair whose seat is made up of 1.4 cm thick hot pressed plywood moulded polyurethane foam and upholstered fabric. It shall be 48cm x 49cm. The two part Back assembly is upholstered with mesh fabric. It is made up of back outer injection moulded in glass filled Polyamide and back inner injection moulded in glass filled Polypropylene. The back consist of adjustable lumber support having and adjustment of 4cm. It is made up of Poluoxymethylene which is upholstered with foam and fabric. Back size shall be 47cm x 53cm. Two way adjustable armrests are made of glass filled Polyamide with PVC armtop having a height adjustment of 8cm along with to and fro movements. The powder coated welded tubular frame is made up of 3.55cm x 1.9cm x 0.15cm thick MSERW oblong tube. The frame is fitted with plastic caps made of injection moulded glass filled Polypropylene. The overall dimensions of the chair shall be 61cm W x 61cm D x 98.5cm H. The seat height shall be 45.5cm H. complete in all respect as per direction of Engineer- In- Charge.

NS 57 - Providing and Placing in place of 1 seater sofa. The overall dimensions of the sofa shall be 860W x 905D x 855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap. complete in all respect as per direction of Engineer- In- Charge.

NS 58 - Providing and placing side table whose glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.complete in all respect as per direction of Engineer- In- Charge.

NS 59 - Providing and placing desk whose size shall be 1500 Width mm x 750 Depth mm x 740 Height mm .Table top shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick backing laminate (bdl) .Flat edge Duly sealed with 2 mm thick PVC beading.The modesty shall be 18 mm thick plain particle board ( ) PPB Clad with 1.0 mm thick decorative laminate (DL) on both sides. Edge Sealed with 2 mm thick PVC beading. ERU size shall be 1050 Width x 450 Depth x 705 Height. The top of ERU shall be 25 mm thick plain particle board (PPB) Clad with 0.6 mm thick post formed laminate and 1 mm thick Backing Laminate ( BDL).Flat Edge duly sealed with 2 mm thick PVC beading. The Modesty shall be 18 mm thick plain particle board (PPB) Clad with 1.0 mm thick Decorative Laminate (DL) on both sides. Edge sealed with 2 mm thick PVC Beading.

NS 60 - Providing and placing storage unit whose size shall be 1200mm(W)x470mm(D)x1169mm(H) . The construction shall be rigid knock down construction . All major panels -0.7 mm thick CRCA, False side panel - 0.9 mm thick ,Bottom Shelf - 0.8 mm thick CRCA sheet . Vertical Handle sections for shutters : 1.2 mm thick CRCA sheet . CRCA D Grade as per IS -513 .Also there shall be 2 adjustable shelves for 1169 H TDU . Uniformly Distributed Load Capacity per each full shelf is 80 Kg maximum .For 1169 H TDU - A4 size box file can be stored vertically on two shelves and clear space above second shelf is 294 mm .The shutter opening shall be double shutters operating in opposite direction giving full accessibility to inside without disturbing aisle . The 10 lever cam lock through lock lever and color should be text. bond white - metal plus shutter - translucent white . Leveler shall be screw type with hex . plastic base and finish shall be epoxy polyester powder coating to thickness of 50 micron (+/- 10).

NS 61 - Providing and placing mesh back chair whose seat is made up of 1.4 cm thick hot pressed plywood moulded polyurethane foam and upholstered fabric. It shall be 48cm x 49cm. The two part Back assembly is upholstered with mesh fabric. It is made up of back outer injection moulded in glass filled Polyamide and back inner injection moulded in glass filled Polypropylene. The back consist of adjustable lumber support having and adjustment of 4cm. It is made up of Poluoxymethylene which is upholstered with foam and fabric. Back size shall be 47cm x 53cm. Two way adjustable armrests are made of glass filled Polyamide with PVC armtop having a height adjustment of 8cm along with to and fro movements. IT shall have tilt mechanism, 360 degree revolving type, tilt tension adjustment, 3 position lock. The class 3 pneumatic height adjustment has stroke of 10cm. The pedestal is injection moulded in glass filled Polyamide and fitted with 5 nos. of twin wheel castors. The pedestal is 64cm PCD. Twin wheel castors shall be injection moulded in Polyamide having 6cm wheel diameter. Headrest- The headrest has an adjustment stroke of 6cm and can be retrofitted to the chair. The overall dimensions of the chair shall be 73cm W x 73cm D x 111- 126cm H. The seat height shall be 42-52cm H. complete in all respect as per direction of Engineer- In- Charge.

'NS 62 - Providing and placing mesh back visitor chair whose seat is made up of 1.4 cm thick hot pressed plywood moulded polyurethane foam and upholstered fabric. It shall be 48cm x 49cm. The two part Back assembly is upholstered with mesh fabric. It is made up of back outer injection moulded in glass filled Polyamide and back inner injection moulded in glass filled Polypropylene. The back consist of adjustable lumber support having and adjustment of 4cm. It is made up of Poluoxymethylene which is upholstered with foam and fabric. Back size shall be 47cm x 53cm. Two way adjustable armrests are made of glass filled Polyamide with PVC armtop having a height adjustment of 8cm along with to and fro movements. The powder coated welded tubular frame is made up of 3.55cm x 1.9cm x 0.15cm thick MSERW oblong tube. The frame is fitted with plastic caps made of injection moulded glass filled Polypropylene. The overall dimensions of the chair shall be 61cm W x 61cm D x 98.5cm H. The seat height shall be 45.5cm H. complete in all respect as per direction of Engineer- In- Charge.

'NS 63 - Providing and placing modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. Combination of top tiles shall be tackable fabric & whiteboard . Bottom tiles - Plain metal. Intermediate blocks shall be given in Decorative Laminate finish. Wires shall be taken into the system through cable ducts from the junction boxes and it shall carried upto the panels through concealed conduits inside the blocks. Metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface shall be 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 X 1500 X 600. pedestal shall have flat metal front, free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 2dr = 2box+1file. CPU trolly shall be provided with castors. It shall have Key board tray. All partitions and side panels shall have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. complete in all respect as per direction of Engineer- In- Charge.

'NS 64 - Providing and placing modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. Combination of top tiles shall be tackable fabric & whiteboard . Bottom tiles - Plain metal. Intermediate blocks shall be given in Decorative Laminate finish. Wires shall be taken into the system through cable ducts from the junction boxes and it shall carried upto the panels through concealed conduits inside the blocks. Metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface shall be 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 X 800. ERU size shall be 900 X 450 pedestal shall have flat metal front, free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 2dr = 2box+1file. CPU trolly shall be provided with castors. It shall have Key board tray. All partitions and side panels shall have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. complete in all respect as per direction of Engineer- In- Charge.

'NS 65 - Providing and placing modular workstation, with partition thickness as 52.4 mm thk and ht - 1200 including powder coated aluminium trims. Combination of top tiles shall be tackable fabric & whiteboard . Bottom tiles - Plain metal. Intermediate blocks shall be given in Decorative Laminate finish. Wires shall be taken into the system through cable ducts from the junction boxes and it shall carried upto the panels through concealed conduits inside the blocks. Metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface shall be 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 X 600. pedestal shall have flat metal front, free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 2dr = 2box+1file. CPU trolly shall be provided with castors. It shall have Key board tray. All partitions and side panels shall have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring.complete in all respect as per direction of Engineer- In- Charge.

'NS 66 -Providing and placing high back chair whose cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane foam and upholstered with high stretch knitted polyester fabric. The back size shall be 45.5cm W x 53.0cm H. The HR polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat offers impact cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form the back spine structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt limiter feature which is inbuilt in saet base and the tension is user weight dependent. The adjustable armrests assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled Polyamide. The pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled Polyamide and fitted with 5 nos. twin wheel castors. The pedestal is 66cm pitch centre diameter and 76cm with castors. The overall dimensions of the chair shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be (44.5-53.8cm). complete in all respect as per direction of Engineer- In- Charge.

'NS 67 -Providing and placing mid back chair with cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane foam and upholstered with high stretch knitted polyester fabric. The back size shall be 44.0cm W x 46.0cm H. The HR polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat offers impact cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form the back spine structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt limiter feature which is inbuilt in saet base and the tension is user weight dependent. The adjustable armrests assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled Polyamide. The pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled Polyamide and fitted with 5 nos. twin wheel castors. The pedestal is 66cm pitch centre diameter and 76cm with castors. The overall dimensions of the chair shall be 76cmx 76cm x(90.5cm-99.8cm). The seat height shall be (44.5-53.8cm). complete in all respect as per direction of Engineer- In- Charge.

'NS 68 -Providing and placing visitor chair with cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane foam and upholstered with high stretch knitted polyester fabric. The back size shall be 44.0cm W x 46.0cm H. The HR polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat offers impact cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form the back spine structure involved in multi dimensional recline motion. Cantiliver type tubular frame assembly shall be powder coated and made up of Ø2.54+- 0.03cm X 0.3+-0.016cm. The overall dimensions of the chair shall be 48.5cm (W) x 58.9cm (D) x 93.3cm (H). Seat height shall be 47.1cm.complete in all respect as per direction of Engineer- In- Charge.

''NS 69 -Providing and placing ALL WOOD HINGED DOOR UNIT (HDU) Size:- 900 (W) X 1200 (H) X 450 (D). Construction & Material Knockdown construction. Door Opening Twin door with self closing hinges of Wood made from18mm Thick Pre Laminated Board. Handle · Aesthetically appealing recessed plastic handle for& wooden Doors. Locking Mechanism Cam lock · 3 point locking mechanism in Wood Door Shelving · Height wise Adjustable Shelf Mounting. Each shelf shall have Uniformly Distributed Load capacity per each shelf is 60 Kg Maximum having 2 nos. Adj. Shelves. Wooden Top shall be be made from Pre-Laminated Board of 25 mm thk. Skirting of 125 mm High shall be provided. Leveler Screw type adjustable Leveler with plastic base. height. Back Panel and Sides of the storageunits will be made out from 18mm thick Pre-Laminated Particle Board. Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 10mm of uneven flooring. complete in all respect as per direction of Engineer- In- Charge.

'NS 70 -Providing and placing reception table whose top shall be of Rubberwood with clean Matt PU finish 18 mm thick , inside radius - 700 mm , outside radius - 1350 mm and depth - 650 mm . Cork shall be 18 mm thick of rubber . Glass shall be Frostered 10 mm thick diamond cut finishing on edges , inside radius shall be - 1202.5 mm , otside radius - 1402.5 mm and depth - 200 mm . The Modesty Panel shall be MS Perforated sheet below worksurface : 0.8 mm (thick) x 665 mm ( height) x 1345 mm (flat length ) . Above Worksurface : 0.8 mm (thick ) x 260 mm (height) x 1345 mm (flat length) . The legs shall be of MS tube 1.6 mm thick diameter 50.8 mm and height 604 mm.complete in all respect as per direction of Engineer- In- Charge.

'NS 71-Providing and placing mid back chair with cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide, moulded polyurethane foam and upholstered with high stretch knitted polyester fabric. The back size shall be 44.0cm W x 46.0cm H. The HR polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat offers impact cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form the back spine structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt limiter feature which is inbuilt in saet base and the tension is user weight dependent. The adjustable armrests assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled Polyamide. The pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled Polyamide and fitted with 5 nos. twin wheel castors. The pedestal is 66cm pitch centre diameter and 76cm with castors. The overall dimensions of the chair shall be 76cmx 76cm x(90.5cm-99.8cm). The seat height shall be (44.5-53.8cm). complete in all respect as per direction of Engineer- In- Charge.

'Schedule - ( D ) Bill of Quantites for Electrical Work (NS Items)

'WORK-ELECTRICAL

'Sub Head - I : MCB & DBs

'NSR-1 Supplying and fixing following rating, four pole, 415 volts, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required.

'NSR-2 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator)

12 way double Door

'SUB HEAD - II : UPS WORK

NSR -3 Supply,Installation,Testing & Commissioning of micro processor controlled True On line double conversion, parallel redundant mode 3 Phase input and 3 phase 415V output UPS & each UPS consisting of followings : UPS module with integrated 100% rectifier+inverter. Battery circuit breaker for each ups module in CRCA housing with all required fixing accessories & hardware. Galvanic isolation transfromer K-rated, at the inverter output of Each UPS module. IN- built static switch for bypass & inverter in each UPS module.In built Manual Maintainance bypass.Interconnecting coper cabling (DC cabling) between UPS, Active filter, Battery breaker & Batteries of required length and size. Sealed maintainance free batteries for 2x30 kva UPS with 30 mins. Back up time on each UPS module with interconnectors, rack and accessories. Rack shall have shrods for safety form live.battery terminals RAM module with each Ups and CAT-5 cable for RAM connecitivity LBS kit for 2N configuration. Ratings of the UPS as follows :- 2x30 kVA parallel redundant UPS operating in parallel redundant configuration (for Emergency Lighting,Work Stations, Fire Alarm, Server and CCTV ). 2x30 KVA UPS = 1 set

'Sub Head-III : UPS PANEL

'NSR-4 Design, fabrication, assembling, wiring, testing, supply, forwarding to site, unloading, shifting to location, inspection, installation, testing and commissioning of UPS panel fabricated out of 14 gauge CRCA sheet steel in cubicle form, Compartmentalized, from 3b construction, free standing floor mounted, dust and vemetrein proof with reinforcement of suitable size angle iron, channel, `T’ sections and/ or flats wherever necessary. 16 gauge CRCA sheet steel shall be used for final distribution panels. 3 mm thick cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before powder coating as per specifications and final approved shade. 2 each earthing temetreinals shall be provided to panels. Panels shall be suitable for 415V, 3 phase, 4 wire, 50 HZ supply system.

'A.Incomer :

'2 Nos. 80A, 4P, MCCB (25kA) with phase indicating lamp protected with 2A, SP, MCCBs and each shall be provided with the following .

'B.Metering & Indication for each incomer :

'i) 1 set of R,Y,B phase indicating lamps

'ii) 1 No. (0-500V) Voltmeter with Built-in VSS with 3 nos. 2A SP MCB

'iii) 1 No. (0-80A) Ammeter with ASS with 3 nos. 80/5A CT's

'iv) 1 No. Digital Electronic KWH meter(Dual Source).

'C.Busbar

'100 A, 4P Copper , colour coded insulated bus bars suitable for 415V, 50Hz AC Supply.

'D.Outgoing:

'i) 1 No. 63 A,4P MCB (10kA)

'ii) 2 Nos. 25 A,DP MCB (10kA)

'iii) 1 No. 40 A,4P MCB (10kA)

UPS PANEL described above

NSR-5 Supply, installation, testing & commissioning of 2 Nos. 80 amps 4P MCCB(25 KA) with thermal Magnetic release (PRMB-3) with Class-C transient voltage surge suppression device suitable for 3 phases as per specifications. The MCCB shall be provided with 2mm thick steel enclosed free standing, dust and vermin proof, encloser with IP42 protection with hinged and lockable doors complete with interconnections.

'SUB HEAD - IV :Light Fixture

'NSR-6.1 Supply, installation, testing & commissioning of Low UGR Recessed Round Led Downlighter consuming a system wattage of 12W (±10%) & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing: Pressure Diecast Aluminium Heat Sink . IP40 , Optics: PMMA/Polysterene Diffuser. The operating CCT should be 5700K with CRI of ≥80. The luminaire should be with BIS Registered electronic driver. , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver should be easily avaiable in India for repair and service. The LED should be SMD type. Luminaire should have minimum surge protection of 2KV. Make -Wipro Cat No.: LD06X-151-XX-57-XX or equvialent to maker list

NSR-6.2 Supply, installation, testing & commissioning of Surface Mount Round Led Downlighter consuming a system wattage of 12W (±10%) & the luminaire shall be with system efficacy ≥ 100 lm / W. Housing: Pressure Diecast Aluminium Heat Sink . IP20 , Optics: PMMA/Polysterene Diffuser. The operating CCT should be 5700K with CRI of ≥80. The luminaire should be with BIS Registered electronic driver , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver should be easily avaiable in India for repair and service. The LED should be SMD type. Luminaire should have minimum surge protection of 2KV Make-Wipro Cat No.: LD06-151-XXX-57WSM or equvialent to maker list

NSR-6.3 Supply, installation, testing & commissioning of Recess Mounted Linear Led Fixture Suitable for techzone ceiling, consuming a system wattage of 28W (±10%) & the luminaire shall be with system efficacy ≥ 120lm/W. Housing: Extruded Aluminium . IP20 , Optics: PMMA/Polysterene Diffuser. The operating CCT should be 5700K with CRI of ≥80. The luminaire should be with BIS Registered electronic driver , THD ≤ 10% & PF ≥ 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Driver should be easily avaiable in India for repair and service. The LED should be SMD type. Luminaire should have minimum surge protection of 2KV. Make- Wipro Cat No.: LM35-381-XXX-57-G1 or equvialent to maker list

NSR-6.4 Supply, installation, testing & commissioning of Recess mounted Direct/ Indirect LED 2'x2' luminaire delivering an initial system lumen of 3340 lumens & the luminaire shall be with system efficacy ≥ 98 lm / W. Housing: CRCA, Optics: polycarbonate/PMMA/Polysterene, IP20 Protection. The operating CCT should be 5700K with CRI of ≥80. The luminaire should be with BIS Registered electronic driver , THD ≤ 10% & PF ≥ 0.95, 50,000 Hrs LED Life with L70 Criteria. The LED Driver should be easily avaiable in India for repair and service. The LED should be SMD type. Luminaire should have minimum surge protection of 2KV. Wipro Cat No.: LM38-461-XXX-57-XX or equvialent to maker list

'SUB HEAD - V : DATA, VOICE NETWORKING

'Supply, installation, testing and commissioning of following Ethernet work station switch as per specification.

NSR-7.1 Supplying, Installation, Testing & Commissioning of 24 port 10/100/1000BASE-T ports and four GbE/10GbE SFP/SFP+ uplink ports layer 3 from day1 having static & RIP , stackable upto 10 switches, should support external redundant power supply, each switch should be provided with stacking port/cable.

NSR-7.2 Supplying, Installation, Testing & Commissioning of 16 port 10/100/1000BASE-T ports and four GbE/10GbE SFP/SFP+ uplink ports layer 3 from day1 having static & RIP , stackable upto 10 switches, should support external redundant power supply, each switch should be provided with stacking port/cable.

'NSR-7.3 Supply and installation of following 19 inch rack for Ethernet switches with A.C. distribution box, wire manager, fan tray, lockable front tinted glass door and two pair angle to support the switch installed in the rack.

42 U Rack

NSR-7.4 Supply, installation, testing and commissioning of following Category 6, IDC patch panel prepackaged with wiring block with legs with legs insert labels, label holders, jumper troughs, metal back panel, duct assembly, screws, washers and an instruction sheet for termination of incoming pairs.24 Port jack panel- loaded

NSR-7.5 Supply and installation of wire manager suitable for mounted on 19 inch rack.

NSR-7.6 Supply, installation, testing and commissioning of 4 pair Category 6A LAN cable consisting of 24 AWG solid copper conductors and as per the specification. The cable shall have flexible jacket and ripcord for easy Strip ability.

NSR-7.7 Supply and installation of flush mounted Enhanced Category 6 outlet. The plastic shall be high impact, flame-retardant, UL rate thermoplastic. Dust cover / blank shall be provided to protect unused faceplate openings. Termination caps and plastic cover shall be provided to protect jack wiring.Single outlet faceplate with RJ-45 jack with information outlet

NSR-7.8 Supply and installation of 6 core MM 50/125 micron OM4 indoor, LSZH, Fibers multitude type Optical Fiber Cable - Armoured

'NSR-7.9 Supply and installation of following Enhanced Category 6 mounting Patch cord for connecting the outlets to the data station (computer/printer etc.). It shall have male RJ 45 connector on one end and male RJ45 connector or open ended wire or a connector suitable for data outlet at the other end. It shall be a 8 conductor. 4 pair cord with each conductor of 24 AWG stranded wire.

NSR-7.9 (a) 1 m long

NSR-7.9 (b) 2 m long

NS-7.10 Supply, installation, testing & Commissioning of 8(2X4) modules brushed brass/copper colour pop-up boxes(All switch socket, DATA outlet, telephone etc are considered separately) .(Make-Legrand, model No.-0540 18)

NS-7.11 Supply, installation, testing & Commissioning of 1 module Female BNC 75 jack Make-Legrand, Model No.- 5722 76 or equvialent to maker list ) for pop up box.

NS-7.12 Supply, installation, testing & Commissioning of 2 Module Female HD15(VGA) (Make-Legrand, Model No.- 5722 82 or equvialent to maker list ) for pop up box.

NS-7.13 Supply, installation, testing & Commissioning of 2 ModuleHDMI socket (Make-Legrand, Model No.- 5722 81 or equvialent to maker list ) for pop up box.

'Sub Head -VI : Access Control System

NSR-8.0 Supply, installation, testing & commissioning of multistand copper conductor PVC sheathed & shielded Cable 8Cx0.25sqmm dia meter complete as required.

'Sub Head -VII : Video Conferencimg System

NSR-9.1 Supply , installation, testing & Comissioning of HDMI Cable 20 meter.

NSR-9.2 Supply , installation, testing & Comissioning of 2 HDMI INPUT and 2 HDMI out Put Converter.

NSR-9.3 Supply , installation, testing of 50" LED-backlit LCD flat panel display, DVI VGA (HD- 15), Component, Composite, HDMI HDCP Compatible direct-lit LED 1080p (FullHD).

NSR-9.4 Supply , installation, testing of 70" LED-backlit LCD flat panel display, DVI VGA (HD- 15), Component, Composite, HDMI HDCP Compatible direct-lit LED 1080p (Ultra HD).

' Sub Head -VIII :Audio Conferencimg System for board room & meeting rooms

NSR-10.1 Supply Installation Testing & Commissioning of Audio patch cord for Conference system.

NSR-10.2 Supply and fixing of Cables 2x2.5 sqmm

NSR-10.3 Supply , installation, testing of 12 U Rack complete as required.

' Sub Head -IX :Supply of MV cable

'NSR-11 Supply, following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor/copper conductor power/ multicore control armoured cable of 1.1 KV grade.

NSR-11.1 3.5 CX 35 sq mm Aluminium armd cable

NSR-11.2 3.5 CX 50 sq mm Aluminium armd cable

NSR-11.3 4CX 25 sq mm Aluminium armd cable

NSR-11.4 4CX 16 sq mm Aluminium armd cable

NSR-11.5 4CX10 sq mm Aluminium armd cable

NSR-11.6 3CX10 sq mm Aluminium armd cable

NSR-11.7 3CX6 sq mm Aluminium armd cable

NSR-11.8 1C X 25 Sqmm Copper flexible Cable

'SUB HEAD - X :RACEWAY

'NS-12 Supplying, installation, testing & commissioning of GI openable bottom cover raceway made from 1.5 mm thick per-galvanized sheets for top, bottom and sides and complete with 1.5 mm thick bottom cover complete with rubber gasketing. The junction box shall be suitable to accommodate GI raceways specified below. Necessary civil work to support/ clamp from RCC slab/floor need to be included here too.(Junction Box price not included in the item).

NSR-12.1 75 mm wide x25 mm deep in ceiling/floor. (single compartment )

NSR-12.2 100 mm wide x25 mm deep in ceiling/floor. (single compartment )

NSR-12.3 150 mm wide x25 mm deep in ceiling/floor.(single compartment )

NSR-12.4 225 mm wide x25 mm deep in ceiling/floor. (double compartment )

NSR-12.5 300 mm wide x25 mm deep in ceiling/floor.(double compartment )

'JUNCTION BOX

'NSR-13 Supplying, installation, testing & commissioning of floor/ceiling recessed junction boxes for GI raceway systems fabricated from 3 mm MS sheets finished with per-galvanized sheets, including 2 nos. GI strip at side for earthing, with 1, 2 or 3 nos "+", "I", ''L' shaped support in the center in case required with 3 mm thick neoprene gasketted removable cover fixed by counter sunk cadmium plated screws including the cost of earth links at all joints to ensure earth continuity and including the cost of chasing and making good recess in floor etc complete as required and as below. (in ceiling / Floor)(Only junction box price included in the item.)

NSR-13.1 150X150X30 mm

NSR-13.2 275X275X30 mm

NSR-13.3 350X350X30 mm

'SUB HEAD - XI :HVAC

'NSR-14 Supplying, installing, testing and commissioning of INLINE FANS direct/belt driven. The cabinet shall be single skin, internally acoustically lined and constructed of galvanized steel. All outdoor application fan shall be of IP 55 rating. The fan shall be SISW with backward curve impeller fitted with maintenance free internal rotor motor. The motor shall be suitable for 220±10%/415±10%(as required).Cost to include necessary switching / Starter panel along with, including cabling ,wiring & earthing as required volt single phase 50 cycles AC supply. All units shall be complete with duct flexible connector and volume control damper. The fan shall have low sound level exceeding not more than 50 DBA at three meter distance.

NSR-14.1 250 CFM Range

NSR-14.2 350 CFM Range

NSR-14.3 450 CFM Range

'CONDENSATE DRAIN PIPING

'NSR-15 Supply installation, testing and fixing of Class’B’ PVC pipes ISI as per IS 4985-2000,SDR 11, drain piping complete with insulation fittings, supports as per specifications.

NSR-15.1 32 mm dia

NSR-15.2 25 mm dia

NSR-16 Supply, fabrication, installation and testing the flexible connections constructed of fire resistance flexible double canvas sleeve as per the approved shop drawings.

'GI Louver

NSR-17 Supplying, installing and testing of Fresh Air GI outlet louvers (Fresh air louver with VCD & bird screen)complete as per specification.

'NSR-18 Supply, Installation, Testing and Balancing of Continuous slot Linear Supply / Return Grilles with removable core as per approved drawings and specifications.

NSR-18.1 Powder coated extruded aluminium construction.

'NS-19 Supply, installation testing and commissioning of duct acoustic insulation. Material shall be nitrile rubber based with 140-180 Kg/m3 density and all accessories as per specification.

NSR-19.1 10 mm thick acoustic lining

'Control wire

'NSR-20 Supply, laying, testing and commissioning of the following sizes of control cum transmission wiring to be laid in PVC conduits between indoor units and outdoor units.

NSR-20.1 2CX1.5 Sqmm copper wire

NSR-20.2 3CX2.5 Sqmm copper wire

Bidder Name

Amount

ULTIMATE INTERNATIONAL PVT.LTD.(GSTN-07AAACU1202F1Z0)

Pooran Chand Sharma and Sons(GSTN-07AAAFP9307K1Z2)

Dovetail Projects Pvt Ltd(GSTN-06AAECD9703A1Z3)

Asha Enterprises Pvt Ltd(GSTN-07AABCA1532H1Z6)

N S Associates Pvt Ltd.(GSTN-07AABCN7057J1Z8)

INTERMARC(GSTN-07AHNPB0193P1Z0)

Mahendru Consultants(GSTN-07AEJPM9444B1ZG)

MANNU LAL AND SONS(GSTN-07AAAFM7256N1ZV)

SUNEHARI BAGH BUILDERS PVT. LTD.(GSTN-07AACCS0523K1ZJ)

CREATORS ENGINEERS AND INTERIORS(GSTN-07AAGFC0762R2Z1)

VirenderKumarAndCo(GSTN-07AAHPK9480H1ZC)

Monaarc Corporation Pvt Ltd(GSTN-24AAGCM4513R1Z5)

GARG BUILDERS(GSTN-07AAPFG3406P2ZX)

Pyramid Builders(GSTN-NA)

SANJEEV FURNISHERS PVT LTD(GSTN-NA)

PUJA CONSTRUCTION COMPANY(GSTN-NA)

AKK BUILDCON PRIVATE LIMITED(GSTN-NA)

ROYEL ELECTRICALS(GSTN-NA)

Vastu Sadan and Associates(GSTN-NA)

GRID INTERIORS PVT LTD(GSTN-NA)

AGNI LIMITED(GSTN-NA)

Aeiforia Constructions Pvt Ltd(GSTN-NA)

METRO ELECTRIC SERVICES(GSTN-NA)

A.S. FURNITURE(GSTN-NA)

Bidder Name

Amount

ULTIMATE INTERNATIONAL PVT.LTD.(GSTN-07AAACU1202F1Z0)

Pooran Chand Sharma and Sons(GSTN-07AAAFP9307K1Z2)

Dovetail Projects Pvt Ltd(GSTN-06AAECD9703A1Z3)

Asha Enterprises Pvt Ltd(GSTN-07AABCA1532H1Z6)

N S Associates Pvt Ltd.(GSTN-07AABCN7057J1Z8)

INTERMARC(GSTN-07AHNPB0193P1Z0)

Mahendru Consultants(GSTN-07AEJPM9444B1ZG)

MANNU LAL AND SONS(GSTN-07AAAFM7256N1ZV)

SUNEHARI BAGH BUILDERS PVT. LTD.(GSTN-07AACCS0523K1ZJ)

CREATORS ENGINEERS AND INTERIORS(GSTN-07AAGFC0762R2Z1)

VirenderKumarAndCo(GSTN-07AAHPK9480H1ZC)

Monaarc Corporation Pvt Ltd(GSTN-24AAGCM4513R1Z5)

GARG BUILDERS(GSTN-07AAPFG3406P2ZX)

Pyramid Builders(GSTN-NA)

SANJEEV FURNISHERS PVT LTD(GSTN-NA)

PUJA CONSTRUCTION COMPANY(GSTN-NA)

AKK BUILDCON PRIVATE LIMITED(GSTN-NA)

ROYEL ELECTRICALS(GSTN-NA)

Vastu Sadan and Associates(GSTN-NA)

GRID INTERIORS PVT LTD(GSTN-NA)

AGNI LIMITED(GSTN-NA)

Aeiforia Constructions Pvt Ltd(GSTN-NA)

METRO ELECTRIC SERVICES(GSTN-NA)

A.S. FURNITURE(GSTN-NA)

Aeiforia Constructions Pvt Ltd

AGNI LIMITED

N S Associates Pvt Ltd.

Pooran Chand Sharma and Sons

Asha Enterprises Pvt Ltd

SANJEEV FURNISHERS PVT LTD

AKK BUILDCON PRIVATE LIMITED

MANNU LAL AND SONS

ROYEL ELECTRICALS

Mahendru Consultants

ULTIMATE INTERNATIONAL PVT.LTD.

VirenderKumarAndCo

INTERMARC

Vastu Sadan and Associates

Pyramid Builders

Dovetail Projects Pvt Ltd

GARG BUILDERS

Monaarc Corporation Pvt Ltd

GRID INTERIORS PVT LTD

SUNEHARI BAGH BUILDERS PVT. LTD.

PUJA CONSTRUCTION COMPANY

A.S. FURNITURE

METRO ELECTRIC SERVICES

Aeiforia Constructions Pvt Ltd

N S Associates Pvt Ltd.

SANJEEV FURNISHERS PVT LTD

AKK BUILDCON PRIVATE LIMITED

MANNU LAL AND SONS

ROYEL ELECTRICALS

Pooran Chand Sharma and Sons

INTERMARC

VirenderKumarAndCo

Pyramid Builders

Dovetail Projects Pvt Ltd

GARG BUILDERS

ULTIMATE INTERNATIONAL PVT.LTD.

Monaarc Corporation Pvt Ltd

Mahendru Consultants

SUNEHARI BAGH BUILDERS PVT. LTD.

GRID INTERIORS PVT LTD

PUJA CONSTRUCTION COMPANY

Vastu Sadan and Associates

A.S. FURNITURE

METRO ELECTRIC SERVICES

AGNI LIMITED

Asha Enterprises Pvt Ltd

AKK BUILDCON PRIVATE LIMITED

N S Associates Pvt Ltd.

Aeiforia Constructions Pvt Ltd

ROYEL ELECTRICALS

SANJEEV FURNISHERS PVT LTD

INTERMARC

ULTIMATE INTERNATIONAL PVT.LTD.

MANNU LAL AND SONS

Mahendru Consultants

Dovetail Projects Pvt Ltd

Pooran Chand Sharma and Sons

Pyramid Builders

Monaarc Corporation Pvt Ltd

VirenderKumarAndCo

GRID INTERIORS PVT LTD

GARG BUILDERS

SUNEHARI BAGH BUILDERS PVT. LTD.

Vastu Sadan and Associates

PUJA CONSTRUCTION COMPANY

A.S. FURNITURE

METRO ELECTRIC SERVICES

AGNI LIMITED

Asha Enterprises Pvt Ltd

Aeiforia Constructions Pvt Ltd

VirenderKumarAndCo

MANNU LAL AND SONS

GARG BUILDERS

ROYEL ELECTRICALS

Monaarc Corporation Pvt Ltd

Pooran Chand Sharma and Sons

Pyramid Builders

SANJEEV FURNISHERS PVT LTD

SUNEHARI BAGH BUILDERS PVT. LTD.

Dovetail Projects Pvt Ltd

N S Associates Pvt Ltd.

INTERMARC

ULTIMATE INTERNATIONAL PVT.LTD.

Asha Enterprises Pvt Ltd

Vastu Sadan and Associates

GRID INTERIORS PVT LTD

METRO ELECTRIC SERVICES

AGNI LIMITED

PUJA CONSTRUCTION COMPANY

Mahendru Consultants

AKK BUILDCON PRIVATE LIMITED

A.S. FURNITURE

Aeiforia Constructions Pvt Ltd

VirenderKumarAndCo

Pooran Chand Sharma and Sons

GARG BUILDERS

SANJEEV FURNISHERS PVT LTD

PUJA CONSTRUCTION COMPANY

MANNU LAL AND SONS

Pyramid Builders

SUNEHARI BAGH BUILDERS PVT. LTD.

Dovetail Projects Pvt Ltd

N S Associates Pvt Ltd.

INTERMARC

ULTIMATE INTERNATIONAL PVT.LTD.

Asha Enterprises Pvt Ltd

Vastu Sadan and Associates

METRO ELECTRIC SERVICES

GRID INTERIORS PVT LTD

AGNI LIMITED

Mahendru Consultants

AKK BUILDCON PRIVATE LIMITED

ROYEL ELECTRICALS

A.S. FURNITURE

Monaarc Corporation Pvt Ltd