SPECIAL REPAIRS TO E/M INSTALLATION AND PROVN OF HT UG CABLE FOR GATE NO 8 TO MES BARABANKI SUB STATION UNDER GE (EAST) LUCKNOW

Amount

Excavation in trenches n.exc. 1.5 mtr wide & n. exc. 1.5 mtr deep in soft/loose soil & getting out all as specified

M & L for PCC (1:5:10) type E-2, using 40mm graded stone aggregate as in foundataion fiiling & mass concrete all as specified

M&L for brick work with modular fly ash bricks, straight or curved on plan exc 6m mean radius in CM 1:6 all as specified.

Returning, filling in including spreading, levelling watering & well ramming in layers n.exc. 25CM thick in soft/loose soil all as specified.

Spreading & levelling in layers n.exc. 25 CM thick well ramming including watering as required.

Removing excavated mtrl n.exc.50 Mtr & depositing where directed at a level n.exc.1.5Mtr above the starting point.

M & L 75mm thick PCC (1:4:8) type D-2, using 40mm graded stone agg as in sub base of flooring all as specified.

M & L 40mm thick (1:2:4) type B-1, using 20mm graded stone agg as in flooring finished the surface even & smooth without using extra cement all as specified.

Supply only water proofing compound

M & L glass dividing strip 38mm wide and 3mm thk complete all as specified

M & L for DPC in PCC (1:2:4) type B-0 to horizontal or vertical surfaces including necessary formwork 40mm thick.

M & L for rendering 15mm thick in CM(1:6) on other than fair faces of brick/concrete work finishing even & smooth without using extra cement.

-dito- as item no 12 above but in CM (1:4) on fair faces of brick work.

-ditto- as item no 12 above but 5mm thick in CM(1:3) on ceiling

M & L for pressed steel frames for doors with one or more rebates including necessary fixing lungs,hinges,lock strike plate etc complete, as specified supplied & fixed (125 x 60mm)

S & F 2nd class hard wood 35 mm thick Plain framed,factory made panelled shutter (two panels) with lock rail and panel of 9mm BWP comercial ply or 12mm vennered particle board with comercial veneering on both faces. The size of rail & stile as per IS: 1003, klin seasoned & chemically pressure treated.

Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 (a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

S & F MS barrel tower bolts, stove enamlled black, with bright bolt& fixed. 200mm long.

MS sliding door bolts, 250 mm long plate type, stove enamlled black, with bright bolt not less than 12mm dia with & including a minimum of 6 bolts & nuts, four on bolt plate & two on staple plate & fixed.

Mild steel pressed handles 150 mm oval type, stove enamlled black

S & F steel windows with side hung shuter including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars.

S & F steel windows with side hung shuter including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars.

Sheet glass 3 mm thk ordinary quality & glazing with oil puty in square n.exc. 0.5 sqm in each pane.

M & L preparation of new wooden surfaces of any description exc 10cm width or girth & aplying two coats of synthtic enamel paint over one coat of pink primer all as specified.

M & L preparation of new steel surfaces of any description exc 10cm width or girth & aplying two coats of synthtic enamel paint all as specified.

M & L for PCC(1:3:6) type C-1, using 20 mm graded agg as in back filling of chowkhats.

M & L for RCC(1:2:4) type B-1, as in slab supported on walls beams & columns in floors, roofs, landing using 20mm graded stone agg (100mm thick)

M & L for RCC (1:2:4) type B-1 as in lintels, beam etc. over 1.5mtr span.

M & L for RCC (1:2:4) type B-1 as in Chajjas

M & L for TMT bars 10mm dia & over cut to length bent to shape required including, cranking binding with & including MS wire not less than 0.90m dia or securing clips.

-dito- as per item no-30 above but MS bar as in stirrups, spacers & binders etc. 5 mm dia and over up to and including 10 mm dia bar.

M & L for formwork to sofits of suspended slabs as roof slabs, floor slabs & similar work n.exc. 250mm thick on rough finished surface of concrete.

-ditto- as item 32 above but to sides and soffits of beams , lintels etc.

ditto as item 32 above but to chajjas including edges

M & L Formwork to edges of concrete flats n.exc. 10cm wide

M & L three coats of white wash on newly plastered surface of wall including preparation the surface of walls all as specified (internal)

M & L two coats of cement base paint on newly plastered surface of walls incl preperation the surface of walls all as specified (External)

-ditto- as item No 36 above but on ceiling

M & L Hardcore brick broken of guage n.exc. 63mm, deposited spread & levelled in layers n.exc.15CM thick, waterd & rammed to a true surface using broken bricks 50 MM thick.

M & L PCC (1:3:6) 75 MM thick as in plinth protection.

M & L Continuous brick edging 75mm wide with brick laid on end vertically with sub cclass 'B' brick all as specified

M & L for rendering 20mm thick in CM(1:4) on fair faces of brick/concrete work with WPC and finishing the surfaceeven & smooth without using extra cement.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire, staples all as specified.

Excavating in post holes (or similar holes) each n exc 0.5 cu m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/loose soil

M&L for cement concrete type C2, 1:3:6 using 40 mm graded stone aggregate as in embedding of fencing post etc,.

S&F for mild steel work in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh etc,.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

S&F galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts including securing or type at crossings with and provision of galvanised mild steel wire staples or steel pins, etc as directed

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire

Supply Chain link fence of 75mm x 75mm mesh size (oblong) of 3-4mm dia GI wire wire complete all as specified.

Supplying, filling in trenches, spreading, leveling sand cushioning 8 cm below cable and 15 cm above the cable and punned up to 18 cm (Note:- Punned thickness suitable measured) for under ground cable complete all as specified & directed by Engr - in - Charge.

M & L Old size sub class 'B' bricks,laid flat in trenches over the cable with length of brick perpendicular to the direction of the cable , adjacent/abutting each other complete all as specified

Dismandling & taking down of existing worn out / unserviceable aluminium conductor, steel reinforced (ACSR)/ structural steel work of any description /size & in any position from existing LT pole/ Lines all as specified and directed .

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty)with stranded aluminium conductor, 11000 earthned system volts grade, of size 3 core 120 sq mm

M & L for Stay assembly 20 mm dia of wire complete with accessories as shown in eletrical plate No1. (loop type insulator , stay clamps, excavation and concreate shall be measured in quoted rate ) complete all as specified and directed.

M & L for Cable jointing kit 11 KV (Earthed) grade cable for outdoor termination heat shrink staright through joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 sqmm to 185 sqmm complete all as specified and directed.

M & L for Cable jointing kit for 11 KV (Earthed) grade cable for outdoor termination heat shrink end type joint complete with jointing material and accessories suitable for 3 core XLPE armoured aluminium conductor cable of size 120 sqmm to 185 sqmm complete all as specified and directed.

M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cm, 6.0 mm thick buried directly in ground vertically at a depth not less than 2.25 metres below normal ground level with top edge of the plate at a depth not less than 1.5 metres below normal ground level, connected with and including GI strip 32mm x 6mm with & including GI pipe 50mm bore light grade as protection pipe (upto the body of equipment max 7.50metre) by means of GI bolts, nuts, check nuts and washers of GI and thimbles, earth plate surrounded by packed layers of coal dust and common salt 15cm thick, all around top and bottom and watering pipe 20mm bore of GI pipe medium grade with funnel and wire mesh complete all as shown in Electrical plate No. 3 of SSR Part-I (2009), testing on completion including PCC chamber (1:3:6) using 20mm graded stone aggregate and RCC M-25 cover and angle iron frame complete all as specified.

M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cm, 6 mm thick buried directly in ground vertically at a depth not less than 2.25 metres below normal ground level with top edge of the plate at a depth not less than 1.5 metres below normal ground level, connected to galvanized earth lead wire 4.0 mm dia with 15 m medium grade pipe fan protection by means of bolts, nuts, check nuts and washers of GI and thimbles, earth plate surrounded by packed layers of coal dust and common salt 15cm thick, all around top and bottom and watering pipe 20mm bore of GI pipe light grade with funnel and wire mesh complete all as shown in Electrical plate No. 5 of SSR Part-I (2009), testing on completion including PCC chamber (1:3:6) using 20mm graded stone aggregate and RCC M-25 cover and angle iron frame complete all as specified. Note for item No 22& 23 :- 1. The cost of GI strip/ wire from top of earth plate upto 5.00 metre above GL with GI protection pipe shall be deemed to be included in unit rate. 2. PCC pit shall be provided at least 0.50 metres away from the earth pit and not just on the earth pit and extra cost of additional length of water pipes and fittings, junction elbow etc shall be deemed to be included in the unit rate. 3. In case the testing result of earthing work not found satisfactory, the contractor shall have to carryout earthwork at new location and nothing extra shall be admissible on this account.

Supply,Installation,Testing & Commissioning of 11kV, 400 Amps, 20 kA/3 Sec Outdoor Non- Extensible Manual RMU Type FR1 VI Type – Stainless Steel tank, comprising of 02 No 11kV, 630 Amps 20kA SF6 Insulated Load Break Switch & 02 Nos. 11kV, 630 Amps 20kA SF-6 insulated Vacuum Circuit Breaker with and inclusive of followings:- Note:- Suitable foundation work is included in the quoted rate as per manufacturer's recommendation.

(a) FR1 – VI 22, 12kV,630A, 21 kA, Fixed type 2 Load Break Switch, 2 Vacuum Circuit Breaker - 1 No (b) SF6 Gas Pressure Indicator -1 (c) Load Break switch -2 Nos (d) Vacuum Circuit Breaker-2 Nos (e) Capacitive Voltage Indication System -4Nos (f) Fault passage indicator-2 Nos (g) Self Powered Relay with O/C & E/F Protection- 2 Nos (h) Current Transformer -100/1A, 2.5VA, CL5P10 - 6 Nos (j) Front cable Termination arrangement for Load Break Switch-2 Nos

(k) Front cable Termination arrangement for Vacuum Circuit Breaker - 2Nos (l) Right angled insualting boots - Set- 4Nos (m) Hardware bolts & nuts- 1 Set (n) Operating Handle - Circuit Breaker & Load Break Switch- 1 Set (o) Lifting Arrangement for ease of Handling- 1 No

Supply, fixing, grouting and painting cable route indicator made up of Factory made Precast RCC slab of size 100 cm x 40 cm x 80 mm thick duly embossed with "MES HT Cable", Size of Cable and grouting on the route of HT cable complete. Note :- (i) Unit rate of item includes excavation, PCC foundation for erection of route indicator. (ii) Slab of route indicate to be provided with min 4 Nos x 8 mm diameters TMT bars along length of slab with 7 Nos cross bar 6 mm dia in reinforcement with shuttering. (iii) Route indicator RCC slab to painting with two coat of red colour synthetic enamel paint over on one coat of white primer base all as specified and directed by Engr - in - Charge.

M&L HT ACSR conductors of any sizes or types etc. complete, complete fixed on insulator mounted on pole complete all as specified & directed.

M & L for single disc type insulator porcelain vitreous 145 mm high and 255mm dia ball and socket type Brown single disc assembly for tension clamps for conductor at working pressure 11000 Volts complete all as specified and directed by Engr - in - Charge.

Supply and fixing GI pipe light grade 80 mm bore for cable protection fixed to poles/along wall/floor/under road/across the drain or nallah including taking down old unserviceable GI pipe complete all as specified and directed.

M & L for PCC (1:4:8) type D-2 using 40 mm graded stone aggregate in foundation of electric poles, struts PCC blocks including necessary form work and fair finish to exposed surfaces without using extra cement etc, complete all as specified and directed

M & L for PCC (1:3:6) type C-2 using 40 mm graded stone aggregate in the foundation of electric poles,stay assembly and struts PCC blocks including necessary form work and fair finish to exposed surfaces without using extra cement etc, complete all as specified and directed .

All as per srl No Item No- 79 here-in-before but PCC (1:2:4) type B-1 using 20mm graded stone aggregate for coping of poles complete all as specified and directed.

Dismantling concrete poles/struts any size complete all as specified and directed .

M&L Steel Tubular swaged pole complete with cast iron base plate, final taper, bolts, nuts and screws etc as specified for type 410-SP-55 (11.00 mtr long) including painting with two coats of aluminium paint over one coat of red oxide primer, duly drilled hole 6nos at top portion of pole for fixing D clamp insulators complete all as specified.

Dismandling switch air break gang operated Switch outdoor type HT 11000 Volt triple poles 200 Amps any type any size complete all as specified and directed .

Material & labour switch air break gang operated Switch outdoor type HT 11000 Volt triple poles 200 Amps with fixed contacts of phosphorus bronze and moving contacts of copper, Horizontal mounted complete with insulator on steel frame, operating rod made out of 25 mm GI pipe medium grade worked from ground level with handle and locking arrangement with 09 insulators with drop out expulsion type fuse of capacity 200 amp mounted on 06 Insulator including painting steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete all as per specified and directed. Note:- 1. Original test certificate of manufacturer shall be produced, without which no payment shall be made. 2. Clamps, cross arms shall be measured and paid for separately.

Supply and fixing HT lightning arresters metal oxide type (Gap less) for outdoor use complete with all fittings, transmission class, discharge capacity 65 kilo amp suitable for 11000 volts including brackets, clamps, nuts, bolts, washers and connecting to earth wire 4mm dia GI wire complete all as specified and directed.

S&F structural steel work conforming to grade Fe-410S as in cross arms, bracing, supports, clamps and back plates fabricated from structural steel sections, including , nuts, bolts, washers, welding , bending cold or hot drilling holes for bolts in any shape or size as indicated or directed and inclusive of one primer coat, one under coat , one finishing coat of aluminium paint and epoxy coating, complete as specified and directed.

S&F danger notice plate of 1.6 mm thick mild steel sheet, vitreous enameled white with letter, figures and conventional skull & bones in signal red colour & fixed with MS clamps, bolts, nuts of size 25 x 20cm for HT 11KV complete all as specified and directed.

Supplying and laying un-reinforced precastconcrete cable cover, class HVP, type 1 withpeak, size 300mm x 180mm x 40mm

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 11000 volts grade with stranded aluminium conductor of size 3 core, 95 Sqmm complete, including earth work, sand cushioning, brick or PCC covering, light grade GI tubing where necessary all as specified and directed.

Supply and fix end cable jointing kit for 11 KV grade cable for outdoor termination , heat shrink type, joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, Al conductor cable of size 70 to 120 sqmm

Supply and fix straight through cable jointing kit for 11 KV grade cable for outdoor termination , heat shrink type, joint complete with jointing material and accessories suitable for 3 core XLPE, armoured, Al conductor cable of size 70 to 120 sqmm

S&F cable route indicator made out of 50x50x6mm angle iron 60 mm long embedded in PCC block of suitable size with moulded letter "HT CABLE" in suitable Ovel shaped inscribed including PCC 1:3:6 type C2 (using 40 mm graded aggregate block of 150 x150x 150 mm sizei complete all as specified and diredcted.

Note for all items i.e BOQ item No. 01 to 92 (a) In case of any item found duplicate in this schedule, contractor should quote same rates, if different rates are quoted for same items having same description /nature of work noticed during execution of work, the lower rate quoted in respective item shall only be allowed for payment. (b) Contractor shall submit the Brochures,pamphlets, literatures,guarantee/warrantee certificates issued by the manufacturers for thenew items supplied and fixed at site as directed by Enginner-in-Charge.

M/S S.B. Singh and Sons (BID ID -3279831)

M/S. KUMAR CONSTRUCTION CO. (BID ID -3278086)

M/s Bapujee Builders and Traders (BID ID -3279178)