Interior and Renovation works of SIDBI Office, Ghaziabad (Uttar Pradesh) and Vishwakarma (Rajasthan)

S.No. Work Description Amount

1 Interior and Renovation works of SIDBI Ghaziabad Office 36,59,820.00

Interior and Renovation works of SIDBI Vishwakarma Industrail

Total Amount 89,63,660.00

Total Amount 89,63,660.00

Digitally signed by AMIT

Interior Fit out works in the office space of SIDBI Office- Ghaziabad

S NO DESCRIPTION Amount

1 Civil Work 14,33,869.00

2 Electrical & Fire-Fighting 5,29,120.00

3 Air Conditioning 7,31,881.00

4 Furniture 9,64,950.00

Total Amount 36,59,820.00

Total Amount 36,59,820.00

Digitally signed by AMIT

Sn Item Description Unit Qty Rate Amount

1 Providing and fixing false ceiling with gypsum board and frame

work made of special section from M.S. sheet and consisting of

angle cleat at 1200mm c/c, one flange fixed to ceiling with dash

fastener 12.5mm dia x50mm long with 6mm dia bolt, other flange

of cleat fixed to the angle hanger of 25x10x0.50mm of required

length with nut & bolt of required size and other end of angle

hanger fixed with intermediate

G.I. channel 45x15x0.9mm running at spacing of 1200mm c/c,

including fixing of gypsum board to ceiling section and perimeter

channel including jointing and finishing to a flush finish of tapered

and square edge of board with jointing compound jointing tape,

and also including the cost of making opening for light fitting, grill,

diffuser, cut-out made

with frame of perimeter channel suitably fixed, all complete.

2 Providing and making partly glazed /partly panelled laminated

partition with galvanized steel internal frame work with 11mm

MDF board on either face laminated using 1.0mm laminate in

required pattern. Rates are inclusive of s/f 8 mm clear glass in Sqm 15.00 5,428.00 81,420.00

glazed portion with required moulding

2a Same as above but finishing of partition with 12 mm gypsum

board on one side inplace of mdf and laminate.Rates are inclusive

of taping , jointing of gypboard all complete

Providing and fixing panelling with framing shall consist of GI

Section on the wall. This framing would be covered by 11mm thick

MDF board with 1mm thick laminate .

3 Providing and fixing 10mm thick Toughened Glass partition with all

required ss hardware & fittings . Sqm 60.00 4,842.00 2,90,520.00

4 Finishing walls with 100% Premium acrylic emulsion paint having

VOC less than 50 gm/litre and UV resistance as per IS 15489:2004,

Alkali & fungal resistance, dirt resistance exterior paint of required

DOOR & LAMINATION

5 Providing and fixing ISI marked flush door shutters 30mm thick

conforming to IS : 2202 (Part I) decorative type, core of block board

construction with frame of 1st class hard wood.

6 Extra for providing lipping with 2nd class teak wood battens 25 mm

minimum depth on all edges of flush door shutters (over all area of

door shutter to be measured). Sqm 6.00 212.00 1,272.00

7 Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of required dia & length.

Digitally signed by AMIT

8 Providing and fixing bright finished brass 100mm mortice lock with

pair of handle /cylendrical lock with 6 levers approved quality with

necessary screws etc. complete. Nos 4.00 2,360.00 9,440.00

9 Providing and fixing aluminium die cast body tubular type universal

hydraulic door closer (having brand logo with ISI, IS: 3564,

embossed on the body, door weight upto 35 kg and door width

upto 700mm) with necessary accessories and screws etc. complete.

10 Providing and fixing aluminium hanging floor door stopper, ISI

marked, anodised (anodic coating not less than grade AC 10 as per

IS : 1868) transparent or dyed to required colour and shade, with Nos 4.00 118.00 472.00

necessary screw etc. complete.

11 Providing & Fixing decorative high pressure laminated sheet of

plain/wood grain in gloss/matt/suede finish with high density

protective surface layer and reverse side of adhesive bonding

quality conforming to IS : 2046 Type S, including cost of adhesive Sqm 10.00 1,000.00 10,000.00

of approved quality.

12 Providing and fixing 12mm thick frameless toughened glass door

with all required ss hardware fittings-Single Shutter size Nos 4.00 22,500.00 90,000.00

Providing & fixing of 4mm thcik vinyl flooring as per sample

approved cost including wastage and fixing charges completel.Size

13 Providing and fixing 16mm thick mineral fibre false ceiling tiles of

size 595X595mm. The tiles should in true horizontal level

suspended on interlocking T-Grid of hot dipped all round

galvanized iron comprising of main T runners of 15x32mm of length

3000mm, cross T of size 15x32mm of length 1200mm and

secondary intermediate cross T of size 15x32mm of length 600mm

to form grid module of size 600x600mm suspended from ceiling

with adjuster of size 85x25x2mm, spaced at 1200mm centre to Sqm 21.00 1,650.00 34,650.00

centre along main ‘T’. The system should rest on periphery

wall/partition with the help of GI perimeter wall angle to be fixed

to the wall with help of plastic rawl plug at 450mm centre to centre

& 40mm long dry wall SS screw.

14 Providing & fixing Film on glasses of door & partition of selected

design and colour all complete.

15 Providing and fixing Mettalic Logo of SIDBI behind public interface

table including fixing of letters in hindi all complete. Nos 1.00 6,000.00 6,000.00

16 Providing and fixing Zebra blind of approve colour fabric with all

required powdercoated channel ,hardware material aluminium clip

,pulling cord etc .all complete Sqm 28.00 2,500.00 70,000.00

17 P/F12 mm ply on external glazing portion for fixing of false

ceilingmembers i/c cutting ,wastage ,labour etc .all complete Sqm 8.50 1,200.00 10,200.00

18 Intensive cleaning of entire branch office premises with required

material ,labour etc i/c all glass partition and its L/S 1.00 5,000.00 5,000.00

section all complete

Digitally signed by AMIT

19 S/F S.S patch lock and SS patch hinge for existing glass main doors

which are damaged i/c removing and refixing of door. Nos 7.00 1,800.00 12,600.00

Total Amount 14,33,869.00

Total Amount 14,33,869.00

Digitally signed by AMIT

S.no Item Description Unit Qty Rate Amount

Electrical work

Supplying, Laying, testing & commissioning of the

following size of XLPE Al. Conductor armoured cables of

1 1.1KV grade on the surface of wall as required

a 4 C x 6.0 Sqmm Cu. Cable Mtrs 20.00 400.00 8,000.00

b 1x 4.0 Sqmm Copper Wire Mtrs 150.00 85.00 12,750.00

DISTRIBUTION BOARDS

Supplying, installation, testing & commissioning of

following type wall mounted Horizontal TPN/SPN

distribution board of double door type design made out

of 16 gauge MS sheet with supplying and fixing

following accessories including painting,

interconnection, painting, earthing and labelling etc. as

Incoming 63Amp TPN MCB (10KA) - 1 No

Busbar 100 Amp TPN copper busbar - 1 Set

Outgoing 10/16/20/25 Amp SP MCB (10KA) - 18

Neutral links - 3 Nos (Separate for each phase)

Incoming 40Amp TPN MCB (10KA) - 1 No

Busbar 100 Amp TPN copper busbar - 1 Set

Outgoing 10/16/20/25 Amp SP MCB (10KA) - 18

Neutral links - 3 Nos (Separate for each phase)

Incoming 63Amp TPN MCB (10KA) - 1 No

Busbar 100 Amp TPN copper busbar - 1 Set

Outgoing 10/16/20/25 Amp SP MCB (10KA) -

Neutral links - 3 Nos

5 63Amp. 4P, 25ka MCB with Box for UPS Set 2.00 2,500.00 5,000.00

Wiring for switch controlled light point with 3x1.5Sqmm

PVC insulated FRLS multistrand copper conductor 1100

Volt grade wires in PVC surface/recessed conduit with

accessories and including the cost of supplying and

fixing 6Amp 240 Volt grid plate mounted switch with

moulded cover plate in zinc chromate passivated MS

box, and costing circuit wiring with 3x2.5sqmm 1100volt

grade PVC insulated FRLS Multistrand

copper conductor wires, in PVC conduit complete

a) Primary Point Pts. 28.00 950.00 26,600.00

b) Secondary Point Pts. 47.00 600.00 28,200.00

Digitally signed by AMIT

Wiring for 5pin 6A Light plug point with 3x1.5Sqmm PVC Pts. 15.00 1,350.00 20,250.00

insulated FRLS multistrand copper conductor 1100Volt

grade wires in recessed FRLS PVC conduit with

accessories including the cost of providing & fixing 1 No.

Modular type 3pin 6A socket outlet controlled by 6A

7 switch in zinc chromate passivated MS box,

and circuit wiring with 3x2.5sqmm complete.

Wiring for following. 13A Socket controlled by 1No 16A Pts. 8.00 1,500.00 12,000.00

Switch with 3x2.5Sqmm PVC insulated FRLS multi strand

copper conductor 1100Volt grade wires in recessed

surface PVC conduit including the cost of providing &

fixing 1No Modular type 20A socket outlet controlled by

1 No. 16A switch in zinc chromate passivated MS

Wiring for following. 16 A Power plug point controlled Pts. 15.00 2,200.00 33,000.00

by 1No 20A MCB with 2 x2.5 +1x1.5 Sqmm PVC

insulated FRLS multi strand copper conductor 1100Volt

9 grade wire in PVC conduit complete. A.C Point

Concealed 16A+6A, socket combined power point as Pts. 18.00 1,700.00 30,600.00

UPS Point comprising of –3 Nos of 6/16 A Universal

Socket & 1 No.16A switch.

TELEPHONE SYSTEM

Supply and fixing of RJ-11 modular Telephone Pts. 15.00 500.00 7,500.00

outlet with Modular Plate

Supply & fixing the 50 pair telephone tag block of Nos 1.00 2,000.00 2,000.00

16 SWG Krone telephone tag block

Supplying & laying the 2 pair telephone wire of Mts 500.00 65.00 32,500.00

PVC insulated in PVC conduit recessed in wall

COMPUTER DATA NETWORKING

Supply and fixing flush steel box computer outlet Nos 20.00 1,450.00 29,000.00

point RJ-45 and cat-6 data cable complete

15.0 Supply and fixing 6U Rack Nos 1.00 8,000.00 8,000.00

16.0 supplying and fixing 12 port switch Nos 1.00 6,000.00 6,000.00

Supply and fixing 24 port Switch Nos 1.00 11,000.00 11,000.00

FANS FIXTURES & LIGHTS

Digitally signed by AMIT

Supplying, installation with hanging support, testing and

commissioning of following light fixtures with electronic

Ballasts, Tubes, lamps, all fixing materials including

connecting wires etc. all complete as per the directions

of Engineer-in- charge (All LED Light Fixtures should be

covered with minimum one year onsite replacement

Recessed LED panel light (L1) (600X600MM) LED 36watt Nos 22.00 2,750.00 60,500.00

18 6500K in false ceiling RC 370 B

Recessed LED down light 15W (165DIA) DN 287 B Nos 30.00 1,050.00 31,500.00

Wall mounting fan 16 inch Nos 8.00 2,000.00 16,000.00

Providing, laying, testing and commissioning of 'C' class Sqm 100.72 675.00 67,986.00

heavy duty MS pipes confirming to IS:3589

/IS:1239 including welding, fittings like Elbow, Tee,

Flange, Nut bolt, Gasket etc. and fixing pipes to

wall/ceiling with suitable clamps and painting with two

or more coats of synthetic enamel paint complete as

required. Also include the UL Flexible Drop Pipe and

Pendent Type Sprinklers. Rate also include s/f butterfly

valve in main line for controlling supply.

Providing, laying, testing and commissioning Smoke Sqm 100.72 325.00 32,734.00

Detector, Heat Sensors, Fire Panels, hooter etc. with all

22 necessary fitting and cabling complete as directed.

Digitally signed by AMIT

S.no Item Description Unit Qty Rate Amount

Supply Installation, Testing & Commissioning of modular type

Variable Refrigerant Flow/Variable Refrigerant Volume air

cooled Outdoor units suitable for cooling and heating, having all

hermetically sealed inverter type Scroll Compressor(s),

minimum two compressors for above 14 HP modules,

microprocessor based Controller, top discharge type

condensing unit(s), with R 410 A Refrigerant, vibration isolators,

with suitable foundation etc. complete as required. The unit

shall deliver the rated capacity at AHRI Conditions and work

even at 50°C ambient temperature without tripping. The unit

shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC

power supply. The unit shall be filled with first charge of the

refrigerant and ready for use as required. The COP at AHRI

conditions shall not be less than 3.1 and IEER not less than 6.5

Supply, installation, testing and commissioning of following

minimum capacity 4-way flow VRV/VRF Cassette Type Indoor

ceiling mounted unit equipped with synthetic washable media

pre-filter, fan section with low noise fan/dynamically balanced

blower, multispeed motor, coil section with DX Copper coil,

electronic expansion valve, outer cabinet, drain pump, grill,

2 necessary supports, vibration isolation, cord less remote control

etc., suitable for operation on single phase 230 V ± 10%, 50Hz

AC supply, complete, as required. The unit shall have automatic

force shut down provision in case of fire on receiving signal from

BMS System. The cooling capacity of indoor unit will be at air

inlet conditions of 27 Degree C DB and 19 Degree C WB

Supply, installation, testing and commissioning of following

minimum capacity VRV/VRF High wall type Indoor unit equipped

with washable synthetic media pre-filter, fan section with low

noise fan/dynamically balanced blower, multispeed motor, coil

section with DX copper coil, electronic expansion valve, outer

less remote control, drain pan, necessary accessories etc.,

suitable for operation on 230 V ± 10%, 50 Hz, single phase AC

3 supply, complete as required. The unit shall have automatic

force shut down provision in case of fire on receiving signal from

BMS System. The cooling capacity of indoor unit will be at air

inlet conditions of 27 Degree C DB and 19 Degree C WB

4 Refrigerant Piping

Digitally signed by AMIT

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal sizes

of soft/hard drawn copper refrigerant piping for VRV/VRF

system, complete with fittings, with suitable adjustable ring

type hanger supports, jointing/brazing including accessories,

insulated with XPLE Class-O tubular insulation/with Class-O

closed cell elastometric nitrile rubber tubular sleeves sections of

specified thickness as given below for Suction and Liquid lines,

all accessories as per specifications etc. as required :

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

19 mm thick insulation Metre 40 245.00 9800.00

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

19 mm thick insulation Metre 80 331.00 26480.00

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

19 mm thick insulation

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

with 19 mm thick insulation

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with

19 mm thick insulation Metre 20 707.00 14140.00

Lifting, Shifting, Supply, Installation, Testing & Commissioning of

Interconnecting "Y" & "T" Joints i.e. Refnet Joints/ Header with

Insulation for refrigearnt piping

Providing & laying of uPVC drain Pipe 25 mm to drain out the

water as per the site requirement

Supplying and drawing following sizes of FRLS PVC insulated

7 copper conductor, single core cable in the existing surface/

recessed steel/ PVC conduit as required.

Total 731881.00

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

2 seater Dimension(L)1390mm X (D)750mm X (H)710mm nos 1 37800 37,800

Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the soft cushioned

backrest and seating. Material & subtype:Premium Leatherette, Colour & Colour Family:as per requirement, Seating

Height:16.14" ,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech solid

wood have used for framing construction of sofa .The seat cushion is made of multi layered foam of density 32-35

kg/m3. The seating cushion have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide

lasting stitch strength . The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm.

2 DGM Visitor Back Chair nos 2 7000 14,000

Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X (H)990mm.A

contemporary design with an all black finish, . Material & subtype:Premium Leatherette, Colour & Colour Family:Black,

Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever, Base:Cantilever Frame, Base Type:Cantilever,

Maximum Seating Height:19".The Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC

with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

3 Conference Medium Back Chair nos 6 8500 51,000

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-(W)590mm X

(D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour lumbar back design made of

12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The chair shall

be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five star chrome base with

nylon castors . Chair seat has foam of density 30-35 (+/-2kg /m3) The backrest has a foam of 28kg/m3.

4 AGM High Back Chair nos 1 13575 13,575

Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x 490mm(D) x

1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof plywood and moulded foam. The seat to

be made with 12 mm thick hot pressed BWR plywood (IS grade - 303) upholsetered with Polyurethane foam and mesh

fabric over it. The chair shall be provided with self tension single locking mechanism and pneumatic height adjustment

which shall have stroke of 10.0 +/- 0.3 cm .The black .The pneumatic height adjustment shall have adjustment stroke of

100 mm and shall be operated at 30kgs extension force.The Seat & back are made up of 12mm thk hot pressed

plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3. The backrest has

a foam of 28kg/m3. adjustable arm rest and head rest

5 Medium Back Chair (work station & conference room) nos 7 7500 52,500

Digitally signed by AMIT

Supplying and placing in position of 360 degrees revolving medium back chair. The breathable mesh back chair with

cushioned fabric seat shall be ergonomically design with adjustable lumbar back support . The chair shall be provisioned

with adjustable armrest (Up-Down) with PP padding and Adjustable Headrest(Can Adjust Movement). The chair shall

be provided with self tension single locking mechanism and pneumatic height adjustment which shall have stroke of

10.0 +/- 0.3 cm .The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at

30kgs extension force.The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with

polyurethane foam, chair seat has foam of density 32-35 kg/m3.

6 AGM Visitor Chair & conference room side chairs nos 3 7000 21,000

Supplying and placing in position of Fix cantilever chair,the chair made of full mesh in black colour.. use of ply: 12 mm

thick hot pressed bwr plywood (is grade - 303 for seat).Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg

per cu meter for best quality cushioning in seat, back: frame of design shall be curved made of two pieces injection

moulded frame cover with mesh .backrest support adjustable lumbar support. Only seat size is 500mm(l)x 500mm(d)x

470mm(h) & the back size is 465mm(l)x 550mm(h) ,Seat max height is @ 470mm .Fixed cantilever chair .base: chrome

plated tubular frame of cantilever type..The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC

with polyurethane foam, chair seat has foam of density 32-35 kg/m3.

7 Modular Workstation

Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) nos 7 29925 2,09,475

Modular Workstation With Side Top with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm

Partition Ht. 1200mm, Double Raceway systems Skirting label and below the table top . lower tile both side laminated

and upper tile inside side fabric, White

Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H 25mm thick Gabel end 18mm thick MDF

board., and 3Drawer top supported Pedestal unit Size 400W x 400D x 725H made in 18mm thick..Complete Made in

MDF Board.. Laminate 1-Frosty White, Laminate2 For drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue, Powder

Coating-Munshel Gray. and White Tinted Glass

Digitally signed by AMIT

Main Table Dimension (L) 1650mm x (D) 750mm x (H) 750mm

Side Runer Dimension (L) 1050mm X (D) 450mm X (H) 750mm

Supplying, and placing in position of main Table as per Image/ drawing.The Table top are made out of 25mm thk

prelam particle board with 2mm thk pvc edge banding & side panel & modesty panel made up of 18mm thick pre-

laminated particle board .The working edges shall be provided with machine pressed 2mm thick PVC edging using

special hot melt glue at hot temperature. The table have a provision of free standing Side Storage of size 1050mm L x

450mm D x 750mm Ht., Storage Top made out of 25mm thick pre laminated particle board and rest all storage to be

made out of 18 mm thick prelaminated particle board . All exposed edges shall be provided with machine pressed 2

mm thick PVC lipping glued with hot melt EVA glue. Storage having a provision of 3 drawer unit, two openable shutter

with D shape handle & central locking arrangement.

9 Medium Height Partition

Supplying and placing in position of sliding tile base modular Workstation as per photograph. Free standing partition

height 1200mm and should be minimum of 62-67mm thick. Partition inner frame is 1.0-1.2mm thick mild steel.

Horizontal and vertical trims are made out of extruded aluminum of 1mm thick. All Panels/trims shall be powder coated

with 50 micron. Aluminum trims are elegantly fixed with hidden connectors on the partition. The frame work shall be fitted

with 9mm thick pre laminated Particle tiles of approved shade. Partition shall have provision for pin up board with fabric/ Sqft 80 1400 112000

white marker/ laminated of approved shade. Partition framework shall have adequate provisions for the movement of

electric data cables at desired 2 levels; one at skirting and another above / below the table top. The complete

partitioning work shall be carried out as per the approved drawing. The product should be as per above given

specification under the guidance of project Engineer in charge.

10 Conference Table

Supplying and placing in position of conference table of required size as per image/drawing. The work surface top

should be of thickness 42mm top prelaminated particle board with 2mm thick PVC edge banding. The side panel are

made up of 36mm thick prelaminated particle & modesty panel are made out of 25mm thick prelaminated particle board nos 1 70000 70000

with 2mm thick PVC edge banding. The wire carrier should be made from 0.6mm thick CRCA & powder coated 40-50

microns. Also having a provision of 6 module flip top box & metal raceway for wire flow.

14 Pantry Table

Providing & Installation of Pantry table of size 1.83 m x 0.75m x 1.05m (ht) made out of 19mm thk. Commercial Board

finished in Recon veneer and DU Pont Coreanof approved shade as per design. The Recon surfaces to be white Duco

painted. A glass top od width 0.2m on SS pegs to be provided above table. One (1) number Drawer pedestal with 3 nos. 1 25000 25000

drawers to be provided under the table.

15 Openable Shutter storage

The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is made of 09mm thick

MDF of approved shade. All the edges of storage surface shall be provided with machine pressed imported PVC lipping

glued with hot melt EVA glue free from any VOC with free groove handle and suitable lock. All exposed area PVC edge

Digitally signed by AMIT

Net Total Amount In Rs = 964950

Net Total Amount In Rs = 964950

Digitally signed by AMIT

Interior Fit out works in the office space of SIDBI Office- Vishwakarma

Industrail Area

S NO DESCRIPTION Amount

1 Civil Work 18,83,433.60

2 Electrical & Fire-Fighting 7,05,550.00

3 Air Conditioning 8,98,556.00

4 Furniture 18,16,300.00

Total Amount 53,03,839.60

Total Amount 53,03,839.60

Digitally signed by AMIT

Sn Item Description Unit Qty Rate Amount

1 Providing and fixing false ceiling with gypsum board and frame

work made of special section from M.S. sheet and consisting of

angle cleat at 1200mm c/c, one flange fixed to ceiling with dash

fastener 12.5mm dia x50mm long with 6mm dia bolt, other flange

of cleat fixed to the angle hanger of 25x10x0.50mm of required

length with nut & bolt of required size and other end of angle

hanger fixed with intermediate

G.I. channel 45x15x0.9mm running at spacing of 1200mm c/c,

including fixing of gypsum board to ceiling section and perimeter Sqm 135.00 1,450.00 1,95,750.00

channel including jointing and finishing to a flush finish of tapered

and square edge of board with jointing compound jointing tape,

and also including the cost of making opening for light fitting, grill,

diffuser, cut-out made

with frame of perimeter channel suitably fixed, all complete.

2 Providing and making partly glazed /partly panelled laminated

partition with galvanized steel internal frame work with 11mm

MDF board on either face laminated using 1.0mm laminate in

required pattern. Rates are inclusive of s/f 8 mm clear glass in

glazed portion with required moulding

2a Same as above but finishing of partition with 12 mm gypsum

board on one side inplace of mdf and laminate.Rates are inclusive

of taping , jointing of gypboard all complete Sqm 92.00 4,000.00 3,68,000.00

Providing and fixing panelling with framing shall consist of GI

Section on the wall. This framing would be covered by 11mm thick

MDF board with 1mm thick laminate . Sqm 20.00 2,550.00 51,000.00

3 Providing and fixing 10mm thick Toughened Glass partition with

with all required ss hardware & fittings . Sqm 11.00 4,842.00 53,262.00

4 Finishing walls with 100% Premium acrylic emulsion paint having

VOC less than 50 gm/litre and UV resistance as per IS 15489:2004,

Alkali & fungal resistance, dirt resistance exterior paint of required Sqm 240.00 118.00 28,320.00

DOOR & LAMINATION

5 Providing and fixing ISI marked flush door shutters 30mm thick

conforming to IS : 2202 (Part I) decorative type, core of block board

construction with frame of 1st class hard wood. Sqm 3.90 3,450.00 13,455.00

6 Extra for providing lipping with 2nd class teak wood battens 25 mm

minimum depth on all edges of flush door shutters Sqm 4.80 212.00 1,017.60

(over all area of door shutter to be measured).

7 Providing wood work in frames of doors, windows, clerestory

windows and other frames, wrought framed and fixed in position

with hold fast lugs or with dash fasteners of required dia & length. Cum 0.05 1,00,000.0 5,000.00

8 Providing and fixing bright finished brass 100mm mortice lock with

pair of handle /cylendrical lock with 6 levers Nos 2.00 2,360.00 4,720.00

approved quality with necessary screws etc. complete.

9 Providing and fixing aluminium die cast body tubular type universal

hydraulic door closer (having brand logo with ISI, IS : 3564,

embossed on the body, door weight upto 35 kg and door width

upto 700mm) with necessary accessories and screws etc. complete. Nos 4,720.00

Digitally signed by AMIT

10 Providing and fixing aluminium hanging floor door stopper, ISI

marked, anodised (anodic coating not less than grade AC 10 as per

IS : 1868) transparent or dyed to required colour and shade, with 2.00 118.00

necessary screw etc. complete.

11 Providing & Fixing decorative high pressure laminated sheet of

plain/wood grain in gloss/matt/suede finish with high density

protective surface layer and reverse side of adhesive bonding

quality conforming to IS : 2046 Type S, including cost of adhesive 8.00 1,000.00

of approved quality.

12 Providing and fixing 12mm thick frameless toughened glass door

with all required ss hardware fittings-Single Shutter size

Providing & fixing of 4mm thcik vinyl flooring as per sample

approved cost including wastage and fixing charges completel.Size

13 Providing and fixing 16mm thick mineral fibre false ceiling tiles of

size 595X595mm. The tiles should in true horizontal level

suspended on interlocking T-Grid of hot dipped all round

galvanized iron comprising of main T runners of 15x32mm of

length 3000mm, cross T of size 15x32mm of length 1200mm and

secondary intermediate cross T of size 15x32mm of length 600mm

to form grid module of size 600x600mm suspended from ceiling

with adjuster of size 85x25x2mm, spaced at 1200mm centre to Sqm 53.14 1,650.00 87,681.00

centre along main ‘T’. The system should rest on periphery

wall/partition with the help of GI perimeter wall angle to be fixed

to the wall with help of plastic rawl plug at 450mm centre to centre

40mm long dry wall SS screw.

14 Providing & fixing Film on glasses of door & partition of selected

design and colour all complete. Sqm 14.00 800.00 11,200.00

15 Providing and fixing Mettalic Logo of SIDBI behind public interface

table including fixing of letters in hindi all complete. Nos 1.00 6,000.00 6,000.00

16 Providing and fixing Zebra blind of approve colour fabric with all

required powdercoated channel ,hardware material aluminium clip

,pulling cord etc .all complete Sqm 20.00 2,500.00 50,000.00

17 P/F12 mm ply on external glazing portion for fixing of false

ceilingmembers i/c cutting ,wastage ,labour etc .all complete

18 Intensive cleaning of entire branch office premises with required

material ,labour etc i/c all glass partition and its L/S 1.00 5,000.00 5,000.00

section all complete

19 S/F S.S patch lock and SS patch hinge for existing glass main doors

which are damaged i/c removing and refixing of door.

Total Amount 18,83,433.60

Total Amount 18,83,433.60

Digitally signed by AMIT

S.no Item Description Unit Qty Rate Amount

Electrical work

Supplying, Laying, testing & commissioning of the

following size of XLPE Al. Conductor armoured cables of

1 1.1KV grade on the surface of wall as required

a 4 C x 6.0 Sqmm Cu. Cable Mtrs 18.00 400.00 7,200.00

b 1x 4.0 Sqmm Copper Wire Mtrs 160.00 85.00 13,600.00

DISTRIBUTION BOARDS

Supplying, installation, testing & commissioning of

following type wall mounted Horizontal TPN/SPN

distribution board of double door type design made out

of 16 gauge MS sheet with supplying and fixing

following accessories including painting,

interconnection, painting, earthing and labelling etc. as

Incoming 63Amp TPN MCB (10KA) - 1 No

2 Busbar 100 Amp TPN copper busbar - 1 Set

Outgoing 10/16/20/25 Amp SP MCB (10KA) - 18

Neutral links - 3 Nos (Separate for each phase)

Incoming 40Amp TPN MCB (10KA) - 1 No

Busbar 100 Amp TPN copper busbar - 1 Set

Outgoing 10/16/20/25 Amp SP MCB (10KA) - 18

Neutral links - 3 Nos (Separate for each phase)

Incoming 63Amp TPN MCB (10KA) - 1 No

Busbar 100 Amp TPN copper busbar - 1 Set

Outgoing 10/16/20/25 Amp SP MCB (10KA) -

Neutral links - 3 Nos

5 63Amp. 4P, 25ka MCB with Box for UPS Set 2.00 2,500.00 5,000.00

Digitally signed by AMIT

Wiring for switch controlled light point with 3x1.5Sqmm

PVC insulated FRLS multistrand copper conductor 1100

Volt grade wires in PVC surface/recessed conduit with

accessories and including the cost of supplying and

fixing 6Amp 240 Volt grid plate mounted switch with

moulded cover plate in zinc chromate passivated MS

box, and costing circuit wiring with 3x2.5sqmm 1100volt

grade PVC insulated FRLS Multistrand

copper conductor wires, in PVC conduit complete

a) Primary Point Pts. 35.00 950.00 33,250.00

b) Secondary Point Pts. 55.00 600.00 33,000.00

Wiring for 5pin 6A Light plug point with 3x1.5Sqmm PVC Pts. 20.00 1,350.00 27,000.00

insulated FRLS multistrand copper conductor 1100Volt

grade wires in recessed FRLS PVC conduit with

accessories including the cost of providing & fixing 1 No.

Modular type 3pin 6A socket outlet controlled by 6A

switch in zinc chromate passivated MS box,

and circuit wiring with 3x2.5sqmm complete.

Wiring for following. 13A Socket controlled by 1No 16A Pts. 15.00 1,500.00 22,500.00

Switch with 3x2.5Sqmm PVC insulated FRLS multi strand

copper conductor 1100Volt grade wires in recessed

surface PVC conduit including the cost of providing &

8 fixing 1No Modular type 20A socket outlet controlled by

1 No. 16A switch in zinc chromate passivated MS

Wiring for following. 16 A Power plug point controlled Pts. 18.00 2,200.00 39,600.00

by 1No 20A MCB with 2 x2.5 +1x1.5 Sqmm PVC

insulated FRLS multi strand copper conductor 1100Volt

grade wire in PVC conduit

UPS WIRINGA.C Point

Concealed 16A+6A, socket combined power point as Pts. 18.00 1,700.00 30,600.00

10 UPS Point comprising of –3 Nos of 6/16 A

Universal Socket & 1 No.16A switch.

TELEPHONE SYSTEM

Supply and fixing of RJ-11 modular Telephone Pts. 22.00 500.00 11,000.00

outlet with Modular Plate

Supply & fixing the 50 pair telephone tag block of 16 Nos 1.00 2,000.00 2,000.00

12 SWG Krone telephone tag block

Supplying & laying the 2 pair telephone wire of PVC Mts 500.00 65.00 32,500.00

13 insulated in PVC conduit recessed in wall

COMPUTER DATA NETWORKING

Digitally signed by AMIT

Supply and fixing flush steel box computer outlet point Nos 30.00 1,450.00 43,500.00

14.0 RJ-45 and cat-6 data cable complete

15.0 Supply and fixing 6U Rack Nos 1.00 8,000.00 8,000.00

16.0 supplying and fixing 12 port switch Nos 1.00 6,000.00 6,000.00

17.0 Supply and fixing 24 port Switch Nos 1.00 11,000.00 11,000.00

FANS FIXTURES & LIGHTS

Supplying, installation with hanging support, testing and

commissioning of following light fixtures with electronic

Ballasts, Tubes, lamps, all fixing materials including

connecting wires etc. all complete as per the directions

of Engineer-in- charge (All LED Light Fixtures should be

covered with minimum one year on site replacement

Recessed LED panel light (L1) (600X600MM) LED Nos 25.00 2,750.00 68,750.00

36watt 6500K in false ceiling RC 370 B

19 Recessed LED down light 15W (165DIA) DN 287 B Nos 45.00 1,050.00 47,250.00

20 Wall mounting fan 16 inch Nos 15.00 2,000.00 30,000.00

Providing, laying, testing and commissioning of 'C' class Sqm 185.80 675.00 1,25,415.00

heavy duty MS pipes confirming to IS:3589

/IS:1239 including welding, fittings like Elbow, Tee,

Flange, Nut bolt, Gasket etc. and fixing pipes to

wall/ceiling with suitable clamps and painting with two

21 or more coats of synthetic enamel paint complete as

required. Also include the UL Flexible Drop Pipe and

Pendent Type Sprinklers. Rate also include s/f butterfly

valve in main line for controlling supply.

Providing, laying, testing and commissioning Smoke Sqm 185.80 325.00 60,385.00

Detector, Heat Sensors, Fire Panels, hooter etc. with all

22 necessary fitting and cablingcomplete as directed.

Digitally signed by AMIT

S.no Item Description Unit Qty Rate Amount

Supply Installation, Testing & Commissioning of modular type

Variable Refrigerant Flow/Variable Refrigerant Volume air

cooled Outdoor units suitable for cooling and heating, having all

hermetically sealed inverter type Scroll Compressor(s),

minimum two compressors for above 14 HP modules,

microprocessor based Controller, top discharge type

condensing unit(s), with R 410 A Refrigerant, vibration isolators,

with suitable foundation etc. complete as required. The unit

shall deliver the rated capacity at AHRI Conditions and work

1 even at 50°C ambient temperature without tripping. The unit Per HP 24 16415.00 393960.00

shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC

power supply. The unit shall be filled with first charge of the

refrigerant and ready for use as required. The COP at AHRI

conditions shall not be less than 3.1 and IEER not less than 6.5

Supply, installation, testing and commissioning of following

minimum capacity 4-way flow VRV/VRF Cassette Type Indoor

ceiling mounted unit equipped with synthetic washable media

pre-filter, fan section with low noise fan/dynamically balanced

blower, multispeed motor, coil section with DX Copper coil,

electronic expansion valve, outer cabinet, drain pump, grill,

necessary supports, vibration isolation, cord less remote control

etc., suitable for operation on single phase 230 V ± 10%, 50Hz

2 AC supply, complete, as required. The unit shall have automatic

force shut down provision in case of fire on receiving signal from

BMS System. The cooling capacity of indoor unit will be at air

inlet conditions of 27 Degree C DB and 19 Degree C WB

3 Refrigerant Piping

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal sizes

of soft/hard drawn copper refrigerant piping for VRV/VRF

system, complete with fittings, with suitable adjustable ring

type hanger supports, jointing/brazing including accessories,

insulated with XPLE Class-O tubular insulation/with Class-O

closed cell elastometric nitrile rubber tubular sleeves sections of

specified thickness as given below for Suction and Liquid lines,

all accessories as per specifications etc. as required :

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

19 mm thick insulation Metre 50 245.00 12250.00

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

19 mm thick insulation Metre 80 331.00 26480.00

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

19 mm thick insulation

Digitally signed by AMIT

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

with 19 mm thick insulation Metre 20 588.00 11760.00

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with

19 mm thick insulation Metre 20 707.00 14140.00

Lifting, Shifting, Supply, Installation, Testing & Commissioning of

Interconnecting "Y" & "T" Joints i.e. Refnet Joints/ Header with

4 Insulation for refrigearnt piping

Providing & laying of uPVC drain Pipe 25 mm to drain out the

5 water as per the site requirement Metre 90 295.00 26550.00

Supplying and drawing following sizes of FRLS PVC insulated

copper conductor, single core cable in the existing surface/

7 recessed steel/ PVC conduit as required.

Total 898556.00

Digitally signed by AMIT

Sr.no Description Unit Qty Rate Amount

3 seater Dimension : (L)1650mm X (D)750mm X (H)710mm nos 2 46800 93,600

2 seater Dimension(L)1390mm X (D)750mm X (H)710mm nos 0 37800 0

Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the soft cushioned backrest and

seating. Material & subtype:Premium Leatherette, Colour & Colour Family:as per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech solid wood have used for

framing construction of sofa .The seat cushion is made of multi layered foam of density 32-35 kg/m3. The seating cushion

have 2.75 & 1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength . The backrest

has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm.

2 DGM High Back Chair nos 1 14500 14,500

Supplying and placing in position of 360 degrees revolving high back chair . The chair of Size :-(W)590mm X (D)505mm X

(H)1180mm - 1280mm. The chair shall be ergonomically design contour lumbar back design made of 12mm thick BWR

plywood (IS Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The chrome plated loop armrest with

padded upholstery is provided for extra comfort. The chair shall be provided with pneumatic height adjustment which shall

have stroke of 10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/-2kg /m3)

Dimensions The backrest has a foam of 28kg/m3.

3 DGM Visitor Back Chair nos 3 7000 21,000

Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X (H)990mm.A

contemporary design with an all black finish, . Material & subtype:Premium Leatherette, Colour & Colour Family:Black,

Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever, Base:Cantilever Frame, Base Type:Cantilever,

Maximum Seating Height:19".The Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with

polyurethane foam, chair seat has foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

4 Conference Medium Back Chair nos 8 8500 68,000

Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size :-(W)590mm X

(D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour lumbar back design made of 12mm

thick BWR plywood (IS Grade - 303 for seat and back) upholstered with leatheritte and cut foam. The chair shall be provided

with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm . Five star chrome base with nylon castors . Chair

seat has foam of density 30-35 (+/-2kg /m3) The backrest has a foam of 28kg/m3.

5 AGM High Back Chair nos 2 13575 27,150

Digitally signed by AMIT

Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x 490mm(D) x 1315mm(H). The

seat cushion to be upholstered on 10-12mm thick water proof plywood and moulded foam. The seat to be made with 12 mm

thick hot pressed BWR plywood (IS grade - 303) upholsetered with Polyurethane foam and mesh fabric over it. The chair shall

be provided with self tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/-

0.3 cm .The black .The pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs

extension force.The Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane

foam, chair seat has foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3. adjustable arm rest and head rest

6 Medium Back Chair (work station & conference room) nos 13 7500 97,500

Supplying and placing in position of 360 degrees revolving medium back chair. The breathable mesh back chair with

cushioned fabric seat shall be ergonomically design with adjustable lumbar back support . The chair shall be provisioned with

adjustable armrest (Up-Down) with PP padding and Adjustable Headrest(Can Adjust Movement). The chair shall be provided

with self tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm .The

pneumatic height adjustment shall have adjustment stroke of 100 mm and shall be operated at 30kgs extension force.The

Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam of

density 32-35 kg/m3.

7 AGM Visitor Chair & conference room side chairs nos 4 7000 28,000

Supplying and placing in position of Fix cantilever chair,the chair made of full mesh in black colour.. use of ply: 12 mm thick hot

pressed bwr plywood (is grade - 303 for seat).Seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter

for best quality cushioning in seat, back: frame of design shall be curved made of two pieces injection moulded frame cover

with mesh .backrest support adjustable lumbar support. Only seat size is 500mm(l)x 500mm(d)x 470mm(h) & the back size is

465mm(l)x 550mm(h) ,Seat max height is @ 470mm .Fixed cantilever chair .base: chrome plated tubular frame of cantilever

type..The Seat are made up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has

foam of density 32-35 kg/m3.

8 Modular Workstation

Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) nos 8 29925 2,39,400

Modular Workstation With Side Top with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm Partition Ht.

1200mm, Double Raceway systems Skirting label and below the table top . lower tile both side laminated and upper tile inside

side fabric, White

Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H 25mm thick Gabel end 18mm thick MDF board., and

3Drawer top supported Pedestal unit Size 400W x 400D x 725H made in 18mm thick..Complete Made in MDF Board..

Laminate 1-Frosty White, Laminate2 For drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating-Munshel

Gray. and White Tinted Glass

9 Linear Workstation

Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) nos 5 21735 1,08,675

Digitally signed by AMIT

Supplying, and placing in position of linear workstation as per Image.The worktop made out of 25mm thk. Prelam Particle

board with 2 mm thk PVC edge banding.The Table top supported on Mild Steel of size 50mm x50mm Slanted Leg and 50mm

x 25mm Horizontal connectors with Powder coting of 50 Micron.Middle Leg :- 0.8 mm thk Metal panel fixed on both side of the

"T" leg for Vertical wire carrying purpose.(Sharing Workstation). 0.8 mm thk Single/Double metal powder coated raceway with

Powder coting of 50 Micron below top for wiring.Vertical wire carrying pole with powder coating 50 micron below top for wiring(

Non- sharing workstation ). Also having a provision of ms perfoated sheet hanging modesty. provision of glass divider rest on

the "D" brackets on the table top between opposite seatings. All working or non working edges shall be provided with machine

pressed 2mm thick PVC edging using special hot melt glue at hot temperature. Provision of pullout PVC keyboard tray and

CPU trolley for each seating. Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination

of 2 drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated Particle board with

provision of handles & Locking arrangement

Main Table Dimension (L) 1650mm x (D) 750mm x (H) 750mm

Side Runer Dimension (L) 1050mm X (D) 450mm X (H) 750mm

Supplying, and placing in position of main Table as per Image/ drawing.The Table top are made out of 25mm thk prelam

particle board with 2mm thk pvc edge banding & side panel & modesty panel made up of 18mm thick pre-laminated particle

board .The working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot

temperature. The table have a provision of free standing Side Storage of size 1050mm L x 450mm D x 750mm Ht., Storage

Top made out of 25mm thick pre laminated particle board and rest all storage to be made out of 18 mm thick prelaminated

particle board . All exposed edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA

glue. Storage having a provision of 3 drawer unit, two openable shutter with D shape handle & central locking arrangement.

Main Table Dimension (L)1800mm X (D) 900mm X (H)750mm

overall Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

Supplying and placing in position of main table as per photograph/drawing .The table shall be made out of 25mm thick pre -

laminated particle board of approved shade. The working and non working edges shall be finished with machine pressed with

2mm PVC egdge banding. The table top shall be supported with MS powder coated "C" shape leg of size 50mm x 50mm with

connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk

pvc edge banding. The table shall be provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side

storage having a provision for three equal drawer unit and two openable shutter & one open storage with shelf in it. The

Side unit top shall be made out of 18mm thick pre laminated particle board and rest all storage to be made out of 18mm thick

pre laminated particle board. Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site

12 Medium Height Partition

Supplying and placing in position of sliding tile base modular Workstation as per photograph. Free standing partition height

1200mm and should be minimum of 62-67mm thick. Partition inner frame is 1.0-1.2mm thick mild steel. Horizontal and vertical

trims are made out of extruded aluminum of 1mm thick. All Panels/trims shall be powder coated with 50 micron. Aluminum

trims are elegantly fixed with hidden connectors on the partition. The frame work shall be fitted with 9mm thick pre laminated

Particle tiles of approved shade. Partition shall have provision for pin up board with fabric/ white marker/ laminated of

approved shade. Partition framework shall have adequate provisions for the movement of electric data cables at desired 2

levels; one at skirting and another above / below the table top. The complete partitioning work shall be carried out as per the

approved drawing. The product should be as per above given specification under the guidance of project Engineer in charge.

13 Conference Table

Supplying and placing in position of conference table of required size as per image/drawing. The work surface top should be

of thickness 42mm top prelaminated particle board with 2mm thick PVC edge banding. The side panel are made up of 36mm

thick prelaminated particle & modesty panel are made out of 25mm thick prelaminated particle board with 2mm thick PVC

edge banding. The wire carrier should be made from 0.6mm thick CRCA & powder coated 40-50 microns. Also having a

provision of 6 module flip top box & metal raceway for wire flow.

Digitally signed by AMIT

14 Pantry Table

Providing & Installation of Pantry table of size 1.83 m x 0.75m x 1.05m (ht) made out of 19mm thk. Commercial Board

finished in Recon veneer and DU Pont Coreanof approved shade as per design. The Recon surfaces to be white Duco

painted. A glass top od width 0.2m on SS pegs to be provided above table. One (1) number Drawer pedestal with 3 drawers to nos. 1.00 25000.00 25,000

be provided under the table.

15 Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC nos. 0.00 2200.00 0

16 Openable Shutter storage

The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is made of 09mm thick MDF of

approved shade. All the edges of storage surface shall be provided with machine pressed imported PVC lipping glued with hot

melt EVA glue free from any VOC with free groove handle and suitable lock. All exposed area PVC edge lipping

Net Total Amount In Rs = 1816300

Net Total Amount In Rs = 1816300

Digitally signed by AMIT