GE/CHM-19/2025-2026 REPAIR / MAINT OF FLOOR AND WALL TILLING INCLUDING INTERNAL WATER SUPPLY IN SECTOR D UNDER AGE B/R I AT CHANDIMANDIR

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing and rubbish of the premisses, complete all as specified and directed.

Demolition of plain cement concrete in ground floor and paving n.exc 15cm thickness below or above ground level complete all as specified and directed.

100mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed.

75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base etc, finished even and rough complete all as specified and directed.

25mm thick Plain cement concrete 1:2:4 type B-0 using 12.5mm graded aggregate as in sub base complete all as specified & directed.

Glazed ceramic tiles, coloured in vertical surface 300mmx450mmx 7mm thick, joint free, first quality, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over 10mm thick rendering in cement mortar 1:4, complete all as specified and directed.

Non skid ceramic coloured tiles of size 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm, superior quality as in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including screed bed or bedding layer of 15mm thick in cement mortar (1:6) complete all as specified & directed by Engineer-in-charge

Non skid ceramic coloured tiles, joint free, first quality, 7 to 8 mm thick (square/ rectangular) area or each tile exceeding 0.18 Square metre but not exceeding 0.38 Square metre, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per serial item No 8 herein before but on skirting etc over and including 10mm thick rendering in cement mortar 1:4

Plain cement concrete 1:5:10 type E-2 using 40mm graded brick coarse aggregate as in sunken floor filling and mass concrete, including demolition of sunken PCC and removal of debris complete all as specified & directed.

3mm thick Atactic polypropylene polymer (APP) based polymeric membrane minimum weighing 3.6kg/sqm and reinforced with polyester non woven fabric (weight not less than 150 gms/sqm) laid over a coat of oil bound bitumen primer @0.40L/Sqm by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS over and included 15mm plastering in CM 1:3 (mixed with WPC) on slab and wall of sunken portion. The membrane shall be laid using butane torch and sealing all joints etc having 75mm side lap joint and 100m end lap joint after preparing the surface as per standard practice and as per manufacturer instructions including dismantling of existing felt /treatment, complete all as specified & directed. NOTE : (i)WPC measured and paid separtely in related item. (ii) Ponding test shall be conducted by the Contractor to check the leakage / seepage in suken portion.

Framed work such as grills, gratings, hold fast etc with ends of bars shouldered and / or riverted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, raillings, frame work of water tanks and similar work confirming to Fe-290 grade E-165 complete all as specified & directed by Engineer-in-charge.

Mild steel, plain, black sheet 1.25mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required, complete all as specified and directed.

Repair of grills, frames guard bars, barred irons doors, and similar work welding only, includig supply and fixing of hinges, peg stay, handle if required in Mild steel door/ window complete all as specified and directed. NOTE : Complete door/ window shall be measured in Square metre

Two coats of synthetic enameled paint on steel and iron surfaces over one coat of red oxide primer on surfaces over 10 cm width or girth including preparation of new surfaces complete all as specified & directed.

Preparation of old steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Preparation of old wooden surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Taking down chowkats or frame n. exc. 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frame exc. 1.5 Sqm and n exc 4 Square metre with shutters, without taking off shutters from the frame, complete all as specified and directed.

Factory made pressed steel frames of profile width 125mm x 60mm fabricated from 1.25 mm thick sheet, for doors with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc. & one shop coat of primer, filling of PCC 1:3:6, including repair of damage portion while taking down of old chowkat complete all as specified and directed.

Factory made pressed steel frames of profile width 105mm x 60mm fabricated from 1.25 mm thick sheet, for doors with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc. & one shop coat of primer, filling of PCC 1:3:6 including repair of damage portion while taking down of old chowkat complete all as specified and directed.

30mm thick flush shutters, solid core costruction, with block board core and plywood face panels, commercial type on both sides etc. complete all as specified and directed.

Glazed and gauged skelton shutter (Factory made) 35mm thick of second class hard wood open rebated & prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut & mitred beads for securing glass etc including priming coat. Size of members of shutters as specified in SSR Part I Section 8, clause 8.20 (a) including Kiln seasoned and chemically pressure treated,complete all as specified & directed.

preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Factory made plain framed panelled shutters, 35mm thick (with two panel) of 2nd class hard wood with lock rail and panels of 9mm thick commercial ply or 12mm thick veneered particle board with commercial veneering on both sides, duly hammer marked. The size of rail & style shall be as per IS 1003 Part-I Kiln seasoned and chemically pressure treated including a shop coat of pink primer complete all as specified & directed.

D' type, 150mm Extruded aluminium alloy handle fabricated type complete all as specified and directed.

D' type, 150mm Extruded aluminium alloy handle fabricated type, fixed as in repair complete all as specified and directed.

D' type, 100mm Extruded aluminium alloy handle fabricated type complete all as specified and directed.

D' type, 100mm Extruded aluminium alloy handle fabricated type, fixed as in repair complete all as specified and directed.

150 mm size aluminium , barrel tower bolt of extruded section complete all as specified and directed.

150 mm size aluminium , barrel tower bolt of extruded section , fixed as in repair complete all as specified and directed.

100 mm size aluminium , barrel tower bolt of extruded section complete all as specified and directed.

100 mm size aluminium , barrel tower bolt of extruded section , fixed as in repair complete all as specified and directed.

Aluminum alloy, anodized, sliding door bolt 250mm long hasp , staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, complete all as specified and directed.

Aluminum alloy, anodized, sliding door bolt 250mm long hasp , staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, as in repair complete all as specified and directed.

300mm mild steel ordinary rat tail rod pattern spring including roller and roller plate, including welding on chowkhat complete all as specified and directed.

300mm mild steel ordinary rat tail rod pattern spring including roller and roller plate, including welding on chowkhat, fixed as in repair complete all as specified and directed.

25mm dia stainless steel curtain rod including fixing fancy types brackets, stops, rollers etc., as in repairs complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification complete all as specified and directed.

Solid PVC board 20mm thick, with 2mm thick prelam PVC sheet on the front face & 2mm relam PVC sheet on back with particle board core fixing in frame at site to cup board sgutter, sheleves and kitchen cabinet complete all as specified and directed. B17

Continuous (piano) hinges, mild steel bright finish, width of flap when open 30mm, fixed as in repair complete all as specified and directed.

100mm hasp and staple,aluminium anodised, including bolt to hinge plate and fixed with screws, complete all as specified and directed.

100mm hasp and staple,aluminium anodised, including bolt to hinge plate and fixed with screws, fixed as in repair complete all as specified and directed.

PVC body magnetic shutter catcher for kitchen cup boards, fixed with standard steel screws, complete all as specified and directed.

PVC body magnetic shutter catcher for kitchen cup boards, fixed with standard steel screws, fixed as in repair complete all as specified and directed.

100 mm size butt hinges medium weight cold rolled mild steel complete, all as specified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge, including making good dismantled portion with PCC (1:2:4) type B-1 in CM 1:3 complete all as specified and directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. NOTE : Glass will be mesured and paid sepreately

Powder coated aluminium grill (minimum thickness of powder coating 50 micron) of approved design / pattern (Apprature of grill should not be more than 75mm) with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200mm center to center, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized aluminium standard section around the opening , including aluminium ‘U’ channel and all necessary fitting complete all as per requirement of Engineer-in-Charge.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm including fixed with tinned tacks / stainless steel wire staples, complete all as specified & directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm including fixed with tinned tacks / stainless steel wire staples, fixed as in repair complete all as specified & directed.

4mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square n.exc 0.5 Sqm in each panes complete all as specified and directed.

4mm thick sheet glass ordinary quality any size and in any type of frame and glazing with oil putty ( or beading ) in square exc 0.5 Sqm in each panes, including hacking out old broken glass complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillar etc complete all as specified and directed.

Brick work with sub class ‘B’ bricks of old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.

Brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified & directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation etc or for shaft, wells, cesspits, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in soft and loose soil all as specified & directed by Engineer-in-Charge.

salt glazed stoneware drain pipe grade ‘A’ 150mm bore, ISI marked, jointed with cement mortar, laid in trenches and tested including fittings of same grade complete all as specified and directed.

Plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, hold fast, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straigth or curved) complete all as specified & directed by Engineer-in-charge. - NOTE : (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds , mitred /stopped ends etc complete all as specified & directed.

PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in surface channels, benching and drains complete all as specified and directed.

Plain cement concrete, type C-2, 1:3:6, using 40mm graded crushed stone aggregate as in bed to drain pipe including packing under pipes and tested after the pipe are laid, complete all as specified and directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floor), beams, staircase, landing, chajjas, shelves and similar suspended work, including cutting of reinforcement to facilitate demolition and removal of debris , complete all as specified and directed.

Mild steel TMT bars 10mm dia and over ,cut to length, bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed.

Taking down cement plaster from brick walls or concrete surfaces including raking out joints, hacking out for key, scrubbing down with water complete all as specified and directed and removing rubbish etc. complete all as specified and directed.

Rendering 15mm thick in Cement and Sand mortar 1:4 over fair faces of brick / concrete ,finished even and smooth without using extra cement, including using water proofing compound, including necessary scaffolding & safety arrangement for plaster upto & including 4 storey building complete all as specified. Note : WPC shall be measured and paid separately.

Rendering 15mm thick in Cement and Sand mortar 1:6 over fair faces of brick/concrete surfaces ,finished even and smooth without using extra cement, complete all as specified and directed.

Rendering 5mm thick in cement mortar 1:3 on fair faces of concrete surfaces as in ceilings , finished fair and smooth, complete all as specified and directed.

Dubbing out average 20mm thick on irregular faces of walls, exposed reinforced surfaces, in Cement and Sand mortar 1:4 complete all as specified and directed

Supply only integral water proofing compound (ISI Marked) complete all as specified & directed.

Complete removal of existing wall treatement (internal / external surface) upto & including 4 storey building complete all as specified and directed.

Applying Wall care putty (average thickness 1-2mm as required for desired smoothness and leveling of surfaces in two or more layers) and sand papering for making the surfaces even and smooth complete all as specified and directed.

Preparation of new surfaces of any description of wall, facia, ceiling, RCC / surface prepared etc and applying two coats of oil bound destemper over a coat of alkali reistant primer complete all as specified and directed.

Finishing walls with Acrylic Smooth exterior paint of required shade, on new work/ surface prepared (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed.

Finishing walls with Acrylic Smooth exterior paint of required shade, on old surface, including prepartion of old surface (Two or more coat applied @ 1.67 ltr/10 sqm ) complete all as specified and directed.

Finishing walls with Acrylic Smooth exterior paint of required shade, on old surface, including prepartion of old surface (One coat applied @ 1.67 ltr/10 sqm ) complete all as specified and directed.

Preparation of wall or similar surface by removing all loose material, clean by wire brush and water, applying two coats of dampproof component, sure seal (Dr Fixit) or equivalent as per manufacturer instruction. Applying the component by brush 1.10kg/sqm for each coat, second coat in perpendicualr direction to first coat and after 4-6 hour dry of first coat, complete all as specified and directed.

Preparation of old decorated wall surfaces and applying two coats of oil bound distemper, including repair of cracks, removal of nails / screw and repair of damage /undulated surface with wall care putty complete all as specified and directed.

Preparation of old decorated wall surfaces and applying one coat of oil bound distemper, including repair of cracks, removal of nails / screw and repair of damage /undulated surface with wall care putty complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of cement base paint (approved colour), including necessary scaffolding over a caot of cement base primer complete all as specified and directed.

Preparation of old surfaces of walls and applying two coats of cement base paint, (approved colour), including necessary scaffolding complete all as specified and directed.

Preparation of old surfaces of walls and applying one coat of cement base paint, (approved colour), including necessary scaffolding complete all as specified and directed.

Preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified.

two coats of white wash on ceiling surfaces including preparation of old plastered surfaces complete all as specified and directed

PVC (SWR) floor trap 100mm bore, plain with grating including jointing to waste pipe jointed and setting/fixed in cement concrete type B-1, 1:2:4 , fixed as in repair complete all as specified and directed.

PVC (SWR) 'P' trap 100mm bore, plain with grating including jointing to waste pipe jointed and setting/fixed in cement concrete type B-1, 1:2:4 , fixed as in repair complete all as specified and directed.

Wash hand basin, vitreous china, flat back, white of size 550 x 400 mm with CP waste coupling, angle brackets, PVC waste pipe, fixed as in repair complete all as specified and directed.

Vitreous china, wash down water closet pan, white, pedestal pattern with ‘P’ or ‘S’ trap, seat cover (excluding, flushing cistern and flush pipe), fixed as in repair complete all as specified and directed.

Plastic water closet seat cover white closed pattern with flat bottom mild steel chromium plated or aluminium hinging device, fixed as in repair complete all as specified and directed.

Vitreous china squatting pan, “Orissa” pattern size 580mm x 440mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe, set with cement concrete, fixed as in repair, complete all as specified & directed.

Health faucet stainless steel body chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect, fixed as in repair complete all as specified and directed.

Chromium plated jet spray with 1.00 metre PVC tube (For European seat) fixed as in repair, complete all as specified and directed.

PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including 32mm dia PVC long bend, set with concrete and making good to floor, fixed in repair complete all as specified & directed.

Taking down and refixing in repair of Wash hand basin, vitreous china, flat back, with waste coupling, angle brackets, PVC waste pipe, complete all as specified and directed.

Taking down and refixing in repair of Vitreous china, wash down water closet pan, white, pedestal pattern with ‘P’ or ‘S’ trap, (excluding, flushing cistern and flush pipe), fixed as in repair complete all as specified and directed.

Taking down and refixing in repair PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including 32mm dia PVC long bend, set with concrete and making good to floor, complete all as specified & directed.

PVC connections 15 mm size with PTMT nuts of length 450 mm , fixed as in repair complete all as specified and directed.

Towel rail 600mm long of CP fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 190gms), fixed as in repair complete all as specified and directed.

Towel ring of CP fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 90gms), fixed as in repair complete all as specified and directed.

Taking up or down steel tubing and connections 15mm bore, complete all as specified and directed.

Taking up or down steel tubing and connections 20mm bore ,complete all as specified and directed.

Taking up or down steel tubing and connections 50mm bore ,complete all as specified and directed.

16 mm (outer dia) CPVC pipes, SDR 11 and Plain CPVC SDR 11 fittings, fixed on walls/ceiling or laying in floors, complete all as specified.

20 mm (outer dia) CPVC pipes, SDR 11 and Plain CPVC SDR 11 fittings, fixed on walls/ceiling or laying in floors, complete all as specified.

20mm Brass Elbow (3/4 X ½) complete all as specified and directed.

20mm Brass Tee complete all as specified and directed.

Male Brass Threaded Adaptor 20mm dia (MTA/ MBTA) ) for CPVC pipe complete all as specified and directed.

Female Brass Threaded Adaptor (FTA/ FBTA) 20mm dia for CPVC pipe complete all as specified and directed.

25 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors , complete all as specified and directed.

50 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors , in complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends, or edges of landings etc. and cutting chases for concealed water tubing, concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, in brick walls, complete all as specified

Bib tap brass, fancy type, long body with wall flange, standard chromium plated, cast copper alloy, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Taking down and refixing in repair Bib taps brass, suitable for 15mm bore pipe,complete all as specified and directed.

Two way Bib tap brass, fancy type, (incl fixing arrangement of health faucet) long body with wall flange, standard chromium plated, cast copper alloy, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

15mm bore pillar tap, fancy type, long body with wall flange, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed.

Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repairs complete all as specified and directed.

Wall mixer system with L bend incl provn of over head shower, cast copper alloy , chromium plated screwed down for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair, complete all as specified and directed

Wash hand Basin brass Mixer of chromium plated hot and cold water screwed down for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair, complete all as specified and directed

32mm dia PVC waste pipe with PTMT nut, fixed as in repair complete all as specified and directed.

Taking down and refixing in repair wash hand Basin brass Mixer of chromium plated hot and cold water screwed down for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard and railing 60cm long, fixed as in repair complete all as specified and directed.

Cast copper alloy, chromium plated, fancy type shower rose with swivel joints 125mm dia including fixing to CPVC pipe 15mm bore, fixed as in repair complete all as specified and directed.

25mm bore Union, brass to connect iron to polyethylene and fixed, fixed as in repairs complete all as specified and directed.

Cutting holes of superficial area n.exc 150 Sqcm and depth upto 30 centimeter into or through brick wall built in cement mortar/ RCC Chajjas, surfaces etc with core cutting method and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required after fixing of mild steel pipe sleeves in wall / slab as required complete all as specified and directed. Note : MS sleeve shall be measured and paid separately.

PVC (SWR) pipe 110mm bore, single/ double socketed in any length with rubber ring joints, having minimum density fixed to walls with MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc, fixed as in repair complete all as specified and directed.

110 mm bore PVC (SWR) bends with acceess door complete, all as specified and directed.

110mm bore PVC (SWR) junction single, (Single T/ Y) equal or unequal, with access door complete all as specified and directed.

PVC (SWR) pipe 110mm bore, single/ double socketed in any length with rubber ring joints, having minimum density laid in trenches or in floor etc, fixed as in repair complete all as specified and directed.

PVC (SWR) pipe, 75mm bore, single/ double socketed in any length with rubber ring joints, having minimum density laid in trenches or in floor etc, fixed as in repair complete all as specified and directed.

75 mm bore PVC (SWR) bends with acceess door complete, all as specified and directed.

75mm bore PVC (SWR) junction single, (Single T/ Y) equal or unequal, with access door complete all as specified and directed.

Plain cement mortar 1:3:6 (type C-1 using 20mm graded aggregate), 75mm thick as in Plinth protection , finishing cement concrete even and smooth without using extra cement, all as specified. Note : 10mm construction joint will be provided and panel should not be more than 3metre in length and joint filled with filler bitumen and sand in ratio (1:3)

500 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) double layered, white in colour, screwable lid, hoisted and fixed in position, including PTMT ball valve 20mm bore & PTMT tank nipple, etc, fixed as in repairs, complete all as specified and directed.

Disconnecting existing tanks exc 500 and n.exc 1000 litres, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing etc. measured separately) complete all as specified & directed by Engineer-in-charge.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified & directed by Engineer-in-charge.

Providing & fixing hangers of 6 mm dia. aluminium (upto 1200mm length), adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat of 40 x 3 mm size, 60mm long and expansion hold fasteners of 12.5mm dia, 40mm long with and including anodised aluminium snap grid of size 605mm x 605mm, framed work for false ceiling with and including 4mm thick non asbestos fibre cement building boards fixed in aluminium framework with screws, complete all as specified and directed

Demolition of stone slabs and tiles of any description or thickness in floors laid, bedded and pointed in any mortar including disposal of demolished material complete all as specified and directed.

Kota Stone Slab flooring, 16-18mm thick, best quality over and including cement screed bed 15mm thick in cement mortar 1:6, laid and jointed with grey cement slurry and pointed with grey cement mixed with pigment to match the shade of the slab including cutting, rubbing, grinding and polishing (Mirror finish) complete all as specified and directed.

All as per serial item No 142 hereinbefore but on skirting / vertical surfaces laid over and including 10mm screed layer in cement mortar 1:3, cutting, rubbing, grinding and polishing complete, all as specified.

20mm thick Granite work (of any type table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in, set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite compelte all as specified and directed.

Green Marble work 15 to 18mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade, complete all as specified and directed.

Sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 510mm x 430mm bowl size 430mm x 380mm x 203mm fixed as in repair compelte all as specified and directed.

Kitchen sink with drainage board made out of stainless steel sheet 1.0mm thick with plug, washers and CP waste coupling, overall size 914mm x 460mm , with bowl of size 405mm x 354mm x 203mm incl fixing cantilever brackets, fixed as in repairs, complete all as specified and directed.

Plate rack of stainless steel of size 610mmx 914mm x 254mm with steel shelves and hanging arrangements for utensil, fixed as in repair complete all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern over and including 25m thick sand base as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

Factory made coloured chequered cement concrete tiles 300mm x 300mm x 22-25mm thick (with grey cement and pigments), set, jointed and pointed in neat cement slurry with grey cement with pigment to match the colour of tiles, glossy finish, laid over and including 20mm thick screed bed in cement mortar 1:6, complete all as specified and directed

NALWA CONSTRUCTIONS (BID ID -3306257)

aggarwal contractors and engineers (BID ID -3306364)

Balwantsinghandco (BID ID -3308321)