COMPREHENSIVE MAINTENANCE OF DAY TO DAY B/R, E/M AND PERIODICAL SERVICES IN GARUD LINE, SARATH LINE, MES COLONY, LUNI ENCLAVE, BANAS AND CERTAIN ANNEXEX MD ACCN AND OTM MIL STATION JALIPA UNDER GE (A) BARMER

Amount

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm incl cutting holes and making good required shape for hold fast block for new frame complete all as specified and as directed by the Engineer-in-Charge.

S&F spray duco painted pressed steel frames made of MS sheet of 1.20mm thickness of size 105 x 60 mm for doors with single or double rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts, PCC 1:3:6 type C-0 in fillinng inside frame & hold fasts etc complete all as specified and as directed by the Engineer-in-Charge. Note :- Distrubed protion of existing floor/ wall/ tile/ plaster etc during fixing of chowkhats shall be repaired to match with exisitng finish. Cost of the same will be included in this items.

S&F spray duco painted pressed steel frames made of MS sheet of 1.20mm thickness of size 125 x 60 mm for doors with single or double rebate including necessary fixing lugs, hinges, lock strike plate, hold fasts, PCC 1:3:6 type C-0 in fillinng inside frame & hold fasts etc complete all as specified and as directed by the Engineer-in-Charge. Note :- Distrubed protion of existing floor/ wall/ tile/ plaster etc during fixing of chowkhats shall be repaired to match with exisitng finish. Cost of the same will be included in this items.

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm incl cutting holes and making good reqd shape for hold fast block for new frame complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description exc 1sqm but not exc 2.00 sqm each complete all as specified and as directed by the Engineer-in-Charge.

S&F solid PVC door frames of size 50x47mm made out of 5mm plain colour PVC sheet supplying and fixing in opening as per specification and drawing shown in SSR complete all as specified and as directed by the Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement complete all as specified and as directed by the Engineer-in-Charge and also including following items supply and fixing in the door at site as per specification :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf Note :- The cost of SS butt hinges, SS tower bolt and SS handles shall be deemed to be inclusive in the unit quoted rates.

S&F factory made ISI marked flush door shutters 35mm thick, BWP conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 2nd class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters and complete all as specified and as directed by the Engineer-in-Charge and also including following items supply and fixing in door at site as per specification :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm - 1 No per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stopper - 1 No per leaf Note :- The cost of SS butt hinges, SS tower bolt, SS handles sliding door bolt/Aldrop and door stopper shall be deemed to be inclusive in the unit quoted rates.

S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-I section 8 clause 8.20 (a) kiln seasoned and chemically pressure treated all as specifeid including stainless steel 304 grade wire cloth (0.36mm nominal dia of wire and average width of aperture 1.40 mm) complete all as specified and as directed by the Engineer-in-Charge and also including following items supply and fixing in door at site as per specification :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x3000mm - 1 nos per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf Note :- The cost of SS 304 grade wire cloth, SS butt hinges, SS tower bolt, SS handles, SS Sliding Door Bolt/Aldrop and SS Door Stopper shall be deemed to be inclusive in the unit quoted rates.

S&F 35mm thick 2nd class hard wood plain, framed,panelled factory made shutters (two panel) with lock rail and panel of 12mm veneered particle board with comercial veneering on both faces.The size of rails and style as per IS-1003 (Part-I) kiln seasoned and chemically pressuretreated complete incl S&F fwg items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 4 nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x3000mm - 1 nos per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf Note :- The cost of SS 304 grade wire cloth, SS butt hinges, SS tower bolt, SS handles, SS Sliding Door Bolt/Aldrop and SS Door Stopper shall be deemed to be inclusive in the unit quoted rates.

S&F stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples or with wooden beads, stainless steel screws and nuts bolts etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of new wooden surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint, first quality, over a coat of pink primer on wooden surface complete all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description exc 1 Sqm and n exc 2 Sqm each and refixing in same opening after cutting by chishel or hand saw, peeling by plane, fixing/ re-placing of hinges, repairing etc including all nales screws, pieces, small let in for making good where hinges, etc. have been removed from chowkhats or frames, shutters, etc. including painting or oiling to match, if required complete all as specified and as directed by the Engineer-in-Charge. (Note : Hinges shall be measured and paid separately)

Taking down shutters of any description exc 1 Sqm and n exc 2 Sqm each and refixing in same opening after cutting by chishel or hand saw, peeling by plane, fixing/ re-placing of hinges, repairing etc including all nales screws, pieces, small let in for making good where hinges, etc. have been removed from chowkhats or frames, shutters, etc. including painting or oiling to match, if required complete all as specified and as directed by the Engineer-in-Charge. (Note : Hinges shall be measured and paid separately)

Taking down shutters of any description exc 1 Sqm and n exc 2 Sqm each and refixing in same opening after cutting by chishel or hand saw, peeling by plane, fixing/ re-placing of hinges, repairing etc including all nales screws, pieces, small let in for making good where hinges, etc. have been removed from chowkhats or frames, shutters, etc. including painting or oiling to match, if required complete all as specified and as directed by the Engineer-in-Charge. (Note : Hinges shall be measured and paid separately)

S&F in repair Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F in repair steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

Hacking out old broken glass [any thickness, size, quality or description] from metal frames including punching or drilling out old glazing pins / spring clips complete all as specified and as directed by the Engineer-in-Charge.

S&F for sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sq.m in each pane complete all as specified and as directed by the Engineer-in-Charge.

S&F for 3mm thick figured glass, pin head type and glazing with putty in square not exceeding 0.50 Sqm in each pane complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples of any type of windows and doors i.e. wooden, steel or aluminium including opening and refixing of frame, shutter or shutter elements if required and new wooden beads in wooden doors, complete all as specified and as directed by the Engineer-in-Charge.

Taking down aluminium door/ windows incl frames and complete fittings of area exc 1.00 sqm but n. exc 4 sqm complete all as specified and as directed by the Engineer-in-Charge.

S&F providing factory made aluminium casement windows with 50 micron powder coating doubled panelled and double shutters consisting of frame and mullion of 101.60 x 44.45 x 1.29 mm and shutters made of 63.5 x 31.75 x 1.29 mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36 mm dia and 1.40 mm aperature in inner shutters complete all as specified and as directed by the Engineer-in-Charge and also including following items supply and fixing in window at site as per specification :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 2 nos per leaf (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf Note :- The cost of 5mm thick glass, SS 304 grade wire cloth, SS butt hinges, powder coated aluminium tower bolt and powder coated aluminium handles shall be deemed to be inclusive in the unit quoted rates.

S&F Door closer hydraulically regulated designation No 3 universal type suitable for door shutter 851mm to 1000mm vide and weight between 61 to 80 kg of aluminium (extruded section body) complete all as specified and directed by engineer-in-charge.

S & F in repair 300mm, mild steel, ordinary rat tail rod pattern springs including roller and roller plate, bearing ISI mark complete including necessary welding work complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs 150 mm over all length floor door stopper, bearing ISI mark, of aluminium alloy body and tongue, anodised with hard drawn steel spring, complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs rubber based door seal fixed to bottom edge of door shutter using small nails / self-adhisive type to minimise gap & avoid entry of insects inside house width min 50mm & length as required at site complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod and including 02 Nos stainless steel brackets/finials fency type, stops fixed with ss screws etc complete all as specified and as directed by the Engineer-in-Charge. Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

S&F in repair of 2 mm Fibre-reinforced plastic sheet of transparent colour of any of size including necessary screw and other accessories including hacking out the same from window or door frame complete all as specified and as directed by the Engineer-in-Charge. Note: Cost of Scaffolding for change of sheet upto four story building also include in the rate.

S&F in repair 6mm thick of size 600x450looking mirror fixed to wall with stainless steel plugs/connecter/spacers/screws etc. chrome finish without any beading, including ends/edges of the mirror to be tapered etched smooth finish etc.complete fixed in position complete all as specified and as directed by the Engineer-in-Charge.

Dismantling wrought iron or mild steel work of any description not othervise provided for complete all as specified and as directed by the Engineer-in-Charge.

S&F MS hollow rectangular/square/circular tubes/pipes of YST 310 Grade as in frame work for roofs/rafters/purlins/chajjas/trusses/ columns/ struts etc and like similar items etc. complete all as specified and as directed by the Engineer-in-Charge.

M&L for mild steel framed work as in doors or gates of angle Gde-Fe-290( Gde-E-165) or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of new surfaces of steel of any description, over 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of plain or corrugated steel sheets in roof coverings any type complete all as specified and as directed by the Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheeting, 0.50 mm thick, of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed by the Engineer-in-Charge.

Dismantling wall and ceiling boarding of any description, thickness including cover fillets complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparation of old painted cement, plaster surfaces of any description over 10cm in girth or width and painting with one coat of plastic emulsion complete all as specified and as directed.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of existing unserviceable RCC/PVC water tank and S&F for Rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of existing unserviceable RCC/PVC water tank and S&F for Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs HDPE PVC lid (tank cover) with locking arrangement for 500/1000 Ltrs capacity PVC tank complete all as specified and as directed by the Engineer-in-Charge.

Disconnecting existing tanks exc. 250 Ltrs but not exc. 500 Ltrs capacity PVC water tank, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and as directed by the Engineer-in-Charge. Note :- Cleaning repairing, etc. measured separately under relevant item

M&L for cleaning and removing, exc. 250 Ltrs but not exc. 500 Ltrs capacity PVC water tank all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified and as directed by the Engineer-in-Charge.

Disconnecting existing tanks exc. 500 Ltrs but not exc 1000 Ltrs capacity PVC water tank, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and as directed by the Engineer-in-Charge. Note :- Cleaning repairing, etc. measured separately under relevant item

M&L for cleaning and removing exc 500 Ltrs but not exc. 1000 Ltrs capacity PVC water tank all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified and as directed by the Engineer-in-Charge.

S&F in rep vitreous china wash down water closet pan (pedestal pattern), white including P or S trap, connection to drain (or outgoing pipe) and to flushing pipe 32mm PVC with and including plastic water closet seat, white closed pattern with flat bottom, cover and mild steel hinges device complete all as specified.

S&F in repair Vitreous china squatting pan of Orissa patten size 580 x 440 white colour including CI S/P trap long size as directed joint run and lead front or back inlet with integral footrest including connection to trap and to flushing pipe,anti-syphonage pipe, etc, fixed in repair complete and making good to floor in PCC 1:2:4 type B 1 using 20mm graded stone agregate complete all as specified and as directed by the Engineer-in-Charge.

Dismantling and and taking down WC pan existing of any description/size and S&F vitreous china premium/1st quality wash down water closet pan floor mounting (Semi-pedestal pattern (Anglo Indian) white colour including CI S/P trap as directed including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc.,with flush pipe PVC 32mm dia and incl. plastic seat cover as recommended by manufacturer closed pattern with flat bottom etc; and including all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and including fixing of PVC long arm S/P trap so that joint is avoided inside the building as well as in wall and outlet straight away come out of wall in all floors G.F. complete in all respect complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs plastic EWC seat cover, coloured closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device complete all as specified and as directed by the Engineer-in-Charge.

Dismantling and and taking down flushing cistern of any description/size and S & F flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, , low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair Vitreous china premium/1st quality wash basin (under counter), white, size 550x400 mm including S&F all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions and all as specified including all Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed by the Engineer-in-Charge. Note : The items for counter will be measured and paid separately.

S&F in repair PVC connection 450mm long and 15 mm dia with brass fly nut at both ends complete all as specified and as directed by the Engineer-in-Charge.

S & F brass chromium plated Health faucet with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs stainless steel plate rack of 600X750X250mm fixed to wall complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair angular stop cock fancy type chromium plated cast copper alloy screwed down, high pressure, screwed ends with wall flange for 15mm bore of iron pipe or for union and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

Taking down or up existing GI tubing & connections and S&F 15mm bore tubes medium grade galvanized with all fittings such as Tee, elbows, sockets, unions, plugs, short lenghts etc. and fixed complete to walls and ceilings or laid in floors concealed or open of any length complete all as specified and as directed by the Engineer-in-Charge.

Taking down or up existing GI tubing & connections and S&F 20 mm bore tubes medium grade galvanized with all fitting such as Tee, elbows, sockets, unions, plugs, short lenghts etc and fixed complete to walls and ceilings or laid in floors of any length complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair Glass shelf size 600 mm long with and including bracket and glass complete set etc. complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair of fancy type pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shank supply and fixing ly nuts for iron pipe of 15mm bore complete all as specified and as directed by the Engineer-in-Charge.

S& in repair Bib taps, CP, fancy type long nose with wall flange screwed for 15mm bore of iron pipe or for brass ferrule and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 15mm bore stop valves, cast copper alloy, chromium plated fancy type with long shank cup (Concealed type) screwed down , high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 15mm dia Bib tap (2 in 1 type) of brass, chromium plated fancy type glossy finish fixed to wall complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs tubular towel rail brass chromium plated 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls complete all as specified and as directed by the Engineer-in-Charge.

Supply & fixed in repairs stainless steel sink with drainage board , made out of 1.00mm thick sheet for kitchen or laboratory with plug,washers, waste pipe, cast irn cantilever bracket of overall size 915x460mm bowl size 410x330x160mm complete all as specified.

S&F in repairs stainless steel sink made out of 1.00mm thick sheet for kitchen or laboratory with plug,washers, waste pipe, cast irn cantilever bracket of 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by the Engineer-in-Charge.

S&F PVC Flexible waste pipe 32/40 mm dia having length 900mm with socket for steel sink/WHB upto floor level complete all as specified and as directed by the Engineer-in-Charge.

Taking down old PVC floor trap and M&L for PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement etc complete, fixed in floor complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 75mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls or laid in floors etc complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs PVC (SWR) bends 75 mm dia any radius with access door complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs PVC (SWR) junction single,(Single T) 75mm dia equal or unequal with access door complete all as specified and as directed by the Engineer-in-Charge.

Dismantling, floor, hearth or wall tiling including CM (bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete un -reinforced in ground floors and pavings n.exc 15cm thickness complete all as specified and as directed by the Engineer-in-Charge.

M&L for 75 mm thick cement concrete 1:4:8 type D2 using 40mm graded stone aggregate as in subbase of flooring / hard standing complete all as specified and as directed by the Engineer-in-Charge.

M&L for 25mm thick PCC 1:2:4 Type B1 with 20mm graded stone aggregate as in levelling course in floor complete all as specified and as directed by the Engineer-in-Charge.

M&L for Glazed ceramic glossy finish tiles coloured in vertical surface 450X300X7mm in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by the Engineer-in-Charge.

M&L for Non Skid ceramic tiles colour tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes ccomplete all as specified and as directed by the Engineer-in-Charge. Note : Work will be in patches or in bulk

M & L for Non-skid ceramic premium quality coloured tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 15 mm thick screed in cement mortar (1:6) over and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed by the Engineer-in-Charge.

All as per item No. 78.00 here-in-beforebut as in skirting over cement mortar backing plaster in CM1:4 15mm thick complete all as specified and as directed by the Engineer-in-Charge.

M & L for Single charge, stainfree, vitrified tiles, Premium (1st) quality straight edge, coloured tiles 600 X 600 mm and 9-10 mm thick, as in floors etc. in any pattern of light coloured tiles as in approved shade, set & jointed in neat cement including and over 15mm th screed bed in CM (1:6) and pointed in white coloured cement to match, in floors etc. complete all as specified and as directed by the Engineer-in-Charge.

All as per Item No. 80.00 item above but as in skirting over cement mortar backing plaster in CM 1:3 10mm thick complete all as specified and as directed by the Engineer-in-Charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and as directed by the Engineer-in-Charge. Note : Work will be in patches or in bulk

M&L for Granite of black / green / imperial red (colour as approved by GE) of any type machine cut as in shelves/steps/counter tops, 20 mm thick, set and jointed in cement slurry over & including screed of 15 mm thick / rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab or with suitable adhesive for fixing on unpolished kota stone slabs and including rubbing, cutting and mirror type polishing and bull nose on exposed sides complete all as specified and as directed by the Engineer-in-Charge. Note : Single piece should be used in steps/cills/jambs/shelves

Demolition of brick work or stone/boulder masonary built in cement mortor including all quoins,arches,pillars etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) complete all as specified and as directed by the Engineer-in-Charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling, Jodhpur type brought upto courses complete all as specified and as directed by the Engineer-in-Charge.

M&L for precast cement concrete block masonry with solid blocks of 1:3:6 type C-1 using 20 mm graded stone aggregate exc 10 cm in width and setting in CM 1:6 complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:4:8, type D-2 (40mm graded aggregate) as in floors,hardstanding complete all as specified and as directed by the Engineer-in-Charge.

M&L for 100 mm thick cement concrete 1:2:4, type B-1 (20mm graded aggregate) as in floors,hardstanding without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for 75mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection including making joint at every 3mtr interval and at corner and filled with mixture of bitumen and sand and finished even and fair and laid in alternate bays complete all as specified and as directed by the Engineer-in-Charge.

M&L for 30mm thick PCC 1:2:4 Type B1 with 20mm graded stone aggregate as in levelling course in floor complete all as specified and as directed by the Engineer-in-Charge.

M&L for cement concrete (1:4:8) type D2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and as directed by the Engineer-in-Charge.

M&L for Providing, cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, roof, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directing complete all as specified and as directed by the Engineer-in-Charge.

M&L for applying neat cement slurry with 3 kg of cement per sqm with mixing of liquid water proofing compound as per manufacturer instructions over surfaces roof, terrace, projection, chajjas, walls after prepration and cleaning of surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L for rendering 10mm thick cement plaster in CM (1:3) on concrete surfaces of roof, terrace, projection, chajjas, walls (old or new), finished even and smooth (without using extra lime or cement) with mixing of WPC as per manufacturer instructions complete all as specified and as directed by the Engineer-in-Charge. (Note : WPC shall be measured and paid separately)

M&L for Applying evenly a priming coat with bituminous primer at 4 Kg per 10 sq metre over plastered/concrete surfaces including prepration complete all as specified and as directed by the Engineer-in-Charge.

M&L for laying of APP based polymeric membrane minimum weight 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150gm/sqm) by torched application method laid over and including applying evenly a tack coat of industrial bitumen S-35 grade (30/40) at the rate of 1.2 kg per Sq.m including cleaning surfaces by on and as per manufacturer instructions complete and all as specified and directed.

M&L for 40mm thick cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) over roof, terrace in concrete including using integral WPC as per manufacturer's instructions, well compacted and fair finish, with complete all as specified and directed.

forming V grooves in concrete surfaces of roofs or terracing n exc 10mm wide and n exc 10mm deep, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed.

M&L for Removing material or dubries retrives from above demolition or cleaning to a distance exceed 1.5 Km and not exceeding 5.0 Km and depositing where directed complete all as specified and directed

Supply and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI(solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner complete all as specified and directed

S&F of Factory Made 18mm thick 100% Solid WPC ( Wood polymer Composite ) Plain Board of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with density not less than 650 kg/cbm , having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N (Edge ), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. complete all as specified and as directed by the Engineer-in-Charge., Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet/Kitchen/Balcony Doors & Cabinets.

M&L for running welding in repairs for metal thick not exc. 6mm including cleaning and preparing the surfaces to be welded together, holding the members in true position while welding & bevelling of edges as required, complete all as specified and as directed by the Engineer-in-Charge.

M&L for welding in repairs n. exc 2.5cm in length Thickness of metal to be welded not exc 6mm complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair Prelaminated particle board of 18/19mm thick, interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination with teak wood leaping on exterior face, fixed with screws as in cupboard shutters of bed room, kitchen and internal shelves complete all as specified and as directed by the Engineer-in-Charge.

S&F for 30mm width of flaps (When open) continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed by the Engineer-in-Charge.

S&F for 75mm size Aluminium anodizes barrel tower bolts of extruded section complete all as specified and as directed by the Engineer-in-Charge.

S&F for 75 mm size aluminium anodized handle complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair magnetic cathes and striking plate for cup board etc complete all as specified and as directed by the Engineer-in-Charge.

S&F for 3 to 4 Cm thick sand stone slabs in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4 or fixed over MS steel frame, including demoltion or proper cutting of old RCC chajja and finish even and smooth exposed surface of RCC with using 15mm thick CM in (1:4) complete all as specified and as directed by the Engineer-in-Charge.

Formwork to sides of flat rough finished surfaces of concrete foundations, footings, bases of columns, columns, beams, slabs, roof slab, lintel, chajjas and similar work; (leak proof type) vertical, horizointal or to batter complete all as specified and as directed by the Engineer-in-Charge.

S&F for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

S&F for Mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

S&F for Mild steel TMT bars but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by the Engineer-in-Charge. Note : Aditional Reinforcement: In the case of the shear relnforcement also, if the diameter of the rebars are reduced, provide 8mm dia stirrups In the form of 7 "U" shaped bars. Tie them properly so that it has a tight contact with the main bars.

M&L for Chipping of 50mm average thickness unsound/weak concrete material from slabs, beams, columns, footings etc. and plaster with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts complete all as specified and as directed by the Engineer-in-Charge.

M&L for Cleaning & applying rust remover on in two coats over rusted reinforcement surface of RCC members and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 2-3 sq. mtr/ltr not less than 50 microns dft to reinforcement surface as per manufacturer’s instructions including all machinery, tools tackles and clearing of debris. Note : Entire Exposed Surface of RCC members after chipping shall be measured and paid.

S&F of new steel or rebars by drilling holes with 10 mm to 25mm dia and 100 to 200mm deep/wide as per IS code of 10D formula and filling the holes after inserting of reinforcement dia 8 to 16mm for anchoring at ends/shear connector and filled the holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy- acrylate fixing and anchoring compound ( having the technical parameters mentioned in material specifications) using standard sealant applicator gun after drilling holes of required diameter at required locations, for holding / fixing / placing in position the steel mesh reinforcement at desired level/ stretching complete all as specified and as directed by the Engineer-in-Charge. Note : Steel/reinforcement shall be paid and measured separately.

M&L for providing Micro concrete M-50 (Minimum grade) at the rate of 25kg per 0.0125 m3 with 20% properly graded 5mm to 10mm silt free aggregate as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine, including all necessary scafolding if required etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for Epoxy Bonding Agent suitable for bonding new to old concrete, bricks and steel components, bricks, tiles etc after the prepration of old concrete/RCC surface by cleaning and removing of dust, dirt, loose particles, laitance etc by wire brushing, scrapping and washing with water complete all as per manufacturer's instructions complete all as specified and as directed by the Engineer-in-Charge.

S&F for heavy duty false work of any height like composite steel section erecting for temporary supports with adjustable arrangement to the structural members like beams, columns, slabs in horozointal or vertical directions etc. to relieve the load on the members during breaking of damaged concrete, removal guniting, excavation or any dismantling work and removed after work complete all as specified and as directed by the Engineer-in-Charge. Note : These supports shall be provided either in the form of props or trestles fabricated using structural steel as per the site requirements complete and all as specified & directed.

S&F for MS props of any height, erecting for temporary supports with adjustable arrangement to the structural members like beams, columns, slabs in vertical directions etc. to relieve the load on the members during breaking of damaged concrete, removal guniting, excavation or any dismantling work and removed after work complete as per the instruction of engineer in-charge. Note : These supports shall be provided either in the form of props or trestles fabricated using structural steel as per the site requirements complete all as specified and as directed by the Engineer-in-Charge.

M&L for special treatment to floor/wall sunken portion with demolition of PCC with plaster of entire sunken area (bottom & sides upto dado level) including removal of demolished material exc 250m and n exc 500m, prepration of surface by cleaning to remove loose particles, dust, latance etc, replacement of floor trap, and applying 10mm thick plaster in CM (1:4) with WPC liquid Conplast 421,and applying one coat each of Nitoproof 100 priming coat @1Ltr/5Sqm, after the priming coat applying Nitoproof 120 on plastered surfaces @1Ltr/2.5Sqm, filling the sunken floor with PCC (1:5:10) using brick bat and WPC Conplast - 421, rendering again 20mm thick in CM (1:4) mixed with WPC Conplast - 421, area of floor upto 1.2Sqm complete all as specified and as directed by the Engineer-in-Charge.

M&L for special treatment to floor/wall sunken portion with demolition of PCC with plaster of entire sunken area (bottom & sides upto dado level) including removal of demolished material exc 250m and n exc 500m, prepration of surface by cleaning to remove loose particles, dust, latance etc, replacement of floor trap, and applying 10mm thick plaster in CM (1:4) with WPC liquid Conplast 421,and applying one coat each of Nitoproof 100 priming coat @1Ltr/5Sqm, after the priming coat applying Nitoproof 120 on plastered surfaces @1Ltr/2.5Sqm, filling the sunken floor with PCC (1:5:10) using brick bat and WPC Conplast - 421, rendering again 20mm thick in CM (1:4) mixed with WPC Conplast - 421, area of floor for kitchen/WHB trap upto 0.25Sqm complete all as specified and as directed by the Engineer-in-Charge.

M&L for special treatment to floor/wall sunken portion with demolition of PCC with plaster of entire sunken area (bottom & sides upto dado level) including removal of demolished material exc 250m and n exc 500m, prepration of surface by cleaning to remove loose particles, dust, latance etc, replacement of floor trap, and applying 10mm thick plaster in CM (1:4) with WPC liquid Conplast 421,and applying one coat each of Nitoproof 100 priming coat @1Ltr/5Sqm, after the priming coat applying Nitoproof 120 on plastered surfaces @1Ltr/2.5Sqm, filling the sunken floor with PCC (1:5:10) using brick bat and WPC Conplast - 421, rendering again 20mm thick in CM (1:4) mixed with WPC Conplast - 421complete all as specified and as directed by the Engineer-in-Charge.

Cutting chases, holes in Brick walls, Stone walls, concrete block or slab walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and as directed by the Engineer-in-Charge.

M&L for walling of random rubble uncoursed ,well bonded ,bedded and solidly hearted built in CM (1:4) and brought up to course complete all as specified and as directed by the Engineer-in-Charge.

All as per item No.127.00 here-in-before above but except stone.

M&L for Brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and as directed by the Engineer-in-Charge.

Extra over lime or sand stone stone walling for hammer dressing to face stones and dressing or face beds and joints, with maximum depression on face from straight edge held against the dressed surface n exc. 20mm, as specified, of random rubble walling, uncoursed or brought upto courses complete all as specified and as directed by the Engineer-in-Charge..

M&L keyed pointing in CM (1:4) to random rubble masonry, uncoursed complete all as specified and as directed by the Engineer-in-Charge.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed by the Engineer-in-Charge.

M&L for jaisalmer stone for wall cladding (of any type) 35-55mm thick machine cut bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of stone exc .08 sqm but nexc 0.11 sqm incuding cutting and polishing type in wall including 20mm thick CM 1:4 for laying jaisalmer stone complete all as specified and directed

M & L for Machine cut kota stone slab flooring 20-25mm thick over, laid over cement screed base , jointed and pointed with grey cement slurry mixed with pigment over 20mm thick cement mortar 1:6 screed bed to match the shade of the slab including rubbing and polishing complete all as specified and as directed by the Engineer-in-Charge. Note : Work will be in patches or in bulk

M & L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar over 10 mm thick cement plaster 1:3 jointed and pointed with grey cement slurry mxed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by the Engineer-in-Charge.

M&L for Kota stone slab 20-25mm thick (in single piece as vertical support and horizointal base for granite top) laid over 15mm thick screed bed in cm 1:6in cooking platform, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by the Engineer-in-Charge.

M&L for Machine pressed precast concrete interlocking paver block rubber moulded any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade including over 25mm thick sand cushioning complete all as specified and as directed by the Engineer-in-Charge.

Demolition of cement Concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified and as directed by the Engineer-in-Charge.

M & L for Providing precast cement concrete type B-1 (1:2:4) with 20mm garded stone aggregate in copings.apex stones,columns, posts, boundary pillars, frame of jallies etc and setting in mortar 1:4 complete with joints to match complete all as specified and as directed by the Engineer-in-Charge.

Dismantling of Trellis work (Jafri), including taking as under of battens in trellis (posts and rails measured separately) complete all as specified and as directed by the Engineer-in-Charge.

Material & Labour for 35mm thick precast cement concrete louvres and jallies type C-0 (1:3:6) using 12.5mm graded stone aggregate (measured solid), in cluding all mouldings and frame set in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs PVC (SWR) bends 75 mm dia any radius with access door all as specified and directed

S&F in repairs PVC (SWR) junction single,(Single T) 75mm dia equal or unequal with access door complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs PVC (SWR) bends 75 mm dia any radius complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs PVC (SWR) bends 110 mm dia any radius complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 110mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls or laid in floors etc complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs PVC (SWR) bends 110 mm dia any radius with access door complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs PVC (SWR) junction single,(Single T) 110mm dia equal or unequal with access door complete all as specified and as directed by the Engineer-in-Charge.

S&F of hand shower with 1.5m hose pipe and wall hook complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 20 mm dia gun metal ,globe or gate valves , with iron wheel head , screwed both ends for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 15 mm dia gun metal ,globe or gate valves , with iron wheel head , screwed both ends for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs Stainless steel gratings with frame, 140 mm dia, with hole for waste pipe connection complete all as specified and as directed by the Engineer-in-Charge.

Supply & Fixing in repair 25 mm bore tubes medium grade galvanized with all fitting such as Tee, elbows, sockets, unions, plugs, short lenghts etc and fixed complete to walls and ceilings or laid in floors of any length including taking down or up existing GI tubing & connections complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 16mm bore of CPVC of food grade pipes SDR 11 and plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 20mm (OD) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/ walls and ceiling fixed in repairs complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 20mm bore Ball valves highpressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 25mm bore Ball valves highpressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 15mm bore PTMT Bib taps standard any colour screwed down for iron pipe and fixed minimum weight 90 gm complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair SS soap dish, approximate size 150x 150x80mm, fixed to plugs with chromium plated brass screws complete all as specified and as directed by the Engineer-in-Charge.

S&F in repairs 15mm bore Brass CP basin mixer for mixing hot & Cold water screwed down for iron pipe complete all as specified and as directed by the Engineer-in-Charge.

Supply & Fixing in repair chromium plated shower rose 125mm round shape fancy type fixed to 15mm bore pipe complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair Toilet paper holder with flat recessed type stainless steel complete all as specified and as directed by the Engineer-in-Charge.

S&F in Towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms) complete all as specified and directed.

S&F in repairs of 32mm Waste coupling of PTMT (half or full threaded) .(Minimum weight 32mm-45gms/40mm-60 gms.for kitchen sink complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair Jet Spray (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.00 metre long flexible tube including making connections and fixed in position complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair PVC connection 600mm long and 15 mm dia with brass fly nut at both ends complete all as specified and as directed by the Engineer-in-Charge.

M & L for Seamless calcium silicate ceiling 8mm thick made out of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately) complete all as specified and as directed by the Engineer-in-Charge.

M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and as directed by the Engineer-in-Charge.

S & F in repair Double action floor spring ISI marked hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repairs complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs mortice lock brass 2 levers vertical type with handle, size 100mm complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs mortice lock brass 4 levers vertical type with handle, size 100mm complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 150mm size aluminium anodized handle complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 100mm size butt hinges, medium weight, cold rolled mild steel, complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair 250mm size aluminium alloy anodized sliding door bolts with Hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs 200 mm long aluminium barrel tower bolts stove enamelled black, with bright bolt and fixed complete all as specified and as directed by the Engineer-in-Charge.

S & F in repairs 150 mm long aluminium barrel tower bolts stove enamelled black, with bright bolt and fixed complete all as specified and as directed by the Engineer-in-Charge.

Taking down cement plaster of any description, any thickness from external surfaces of walls/soffits etc. incl raking out joints, hacking for keys, scrubbibg down with water etc complete all as specified and as directed by the Engineer-in-Charge.

M & L for rendering Cement plastering 15mm thick in two layers (10mm and 5mm respectively) in cemet mortar 1:4 including mixing of liquid water proofing compound as per manufacturer's instructions on brick work or concrete surfaces or in chajjas/parapet walls etc finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. Note : WPC will be measured and paid separately.

Supply only integral liquid water proofing compound complete all as specified and directed.

M&L for preparation of new plastered surfaces of external walls/RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc including cornices and applying two coat of cement base paint over a one coat of of external primer by using following brands of cement base paint complete all as specified and as directed by the Engineer-in-Charge.

Complete removal of existing treatment of any type/description such as cement base paint,external emulsion etc from external surfaces of walls/RCC surfaces/soffits of chajjas/roof projections/cantilivers/balcony etc with mechanical means/grinder complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparing existing treated surfaces of external walls/RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc including cornices and applying two coat of cement base paint over a coat of primer by complete all as specified and as directed by the Engineer-in-Charge. Note for above items of external finishing :- the cost for steel tubular double scaffolding necessary for execution of work and protective measures for height more than height of double storey building as directed by engr-in-charge shall be included in the quoted rate against the respective item and nothing shall be admisible for this .

M&L for preparing existing treated surfaces of external walls/RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc including cornices and applying one coat of cement base paint complete all as specified and as directed by the Engineer-in-Charge. Note for above items of external finishing :- the cost for steel tubular double scaffolding necessary for execution of work and protective measures for height more than height of double storey building as directed by engr-in-charge shall be included in the quoted rate against the respective item and nothing shall be admisible for this.

Writing letters or figures ( Block, Roman, Italic or indian ) not exceeding 30cm high complete all as specified and as directed by the Engineer-in-Charge.

Writing stops, commas,short lines, dashes,hyphens, brackets complete all as specified and as directed by the Engineer-in-Charge.

M & L for 10mm thick rendering cement plastering in cement mortar 1:6 on fair faces of brick work or concrete surfaces finished fair & even without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

M&L for cement plastering 5mm thick in cemet mortar 1:3 as on ceilings or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Complete removal of existing treatment of any type/description such as distempering work, internal emulsion etc from internal surfaces of walls with mechanical means/grinder complete all as specified and as directed by the Engineer-in-Charge.

Complete removal of existing treatment of any type/description such as distempering work, internal emulsion etc from internal surfaces of ceiling with mechanical means/grinder complete all as specified and as directed by the Engineer-in-Charge.

M&L for Applying acrylic thick wall care putty on internal surfaces of walls/ceilings (thickness vary from 1.5 to 3.00 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving interior painting complete all as specified and as directed by the Engineer-in-Charge. Notes: (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further external finishes. Please note that the further external finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order.

M&L for applying two coats of OBD by using roller to wall surfaces over & including a coat of interior wall primer coat as recommended for under coat by manufacturer of interior emulsion and primer complete all as specified and as directed by the Engineer-in-Charge.

M & L for preparing existing treated surfaces on walls by filling wall putty in depressions, sand papering etc and making the surface smooth and applying 01 coat of OBD using roller to wall surfaces over complete all as specified and as directed by the Engineer-in-Charge.

M&L for complete removal of existing treatment and Applying 02 coats of interior emulsion paint (light shade) @12 sq.m/litre/2 coats to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparing new plastered surfaces of walls and applying three coats of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the last two coats of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by the Engineer-in-Charge.

M&L for preparing new plastered surfaces of ceilings and applying three coats of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the last two coats of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by Engineer-in-Charge.

M&L for preparing old plastered/unplastered surfaces of walls and applying two coats of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the last two coats of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by the Engineer-in-Charge.

M&L for applying three coats of white wash on ceiling surface by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the last two coats of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by the Engineer-in-Charge.

M & L for preparing existing treated surfaces on walls including cornices and applying one coat of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by the Engineer-in-Charge.

M & L for preparing existing treated surfaces on ceiling including cornices and applying one coat of white wash by making the lime slaked at site and shall be mixed and stirred with about five liters of water for 1 kg of unslaked lime to make a thin cream. This shall be allowed to stand for a period of 24 hours and shall then be screened through clean coarse cloth. 1 kg of gum dissolved in hot water shall be added to every one cubic meter of lime cream. About 1.3 Kg of sodium chloride dissolved in hot water shall also be added for every 10 kg of lime for making the coating hard and rub-resistant. Small quantity of ultramarine blue (upto 3 gm per kg of lime) shall also be added to the of white wash solution and the whole solution shall be stirred thoroughly before use complete all as specified and as directed by the Engineer-in-Charge.

M & L for preparing old painted steel and iron surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engr-in- Charge.

M & L for preparing old painted steel and iron surfaces of any description, not exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

M & L for preparing old painted wood & wood based surfaces of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

M & L for preparing old painted wood & wood based surfaces of any description, not exc 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Providing and fixing factory made alumiium casement windows with 50 micron powder coating doubled panelled and double shutter consisting of rame and million of 101.60x44.45x1.29 mm and shutter made of 63.5x31.75x1.29mm and to be fixed with and including EPDM gasket to render the glazing,air and water tight etc and aluminium beeds 20mm size and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40mm aperture in inner shutter complete fixed in all respect as specified including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 2 nos per leaf (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf

Powder coated 50 micron extruded aluminium frame for fixed type partition (standard two panel pattern)made out of powder coated aluminium section of size 63.5x38.1x1.5mm comprising of 5mm thick tineted glass inserted in and including necessry jointed cleats,rubber packing,anodised aluminium snap beading complete fixed to floor and wall by means of cadium plated steel screws complete incl taking down of existing partition with all fitting and fixures complete all as specified and as directed

Repairs existing aluminium door/ window shutter including frame with completely/partially taking down door shutter and tightening of all screws, replacing including provision of unservicable hinge, handle, lock, aluminium plate & floor door stopper and complete all as specified and as directed by the Engineer-in-Charge.

S&F Aluminium door closer hydraulically aluminium die cast body regulated designation No. 2 universal type (ISI Make) suitable for door shutters of 701 to 850mm in width and of weight between 36 to 60 Kg complete all as specified and as directed by the Engineer-in-Charge.

Taking down carefully copper/aluminium point wiring (light, fan socket or power) complete including PVC Casing Capping/concealed conduit, fixture and fitting such as switches, ceiling roses, pendents, regulators, sockets , light fitting etc removing materials for taking credit and making good disturbed surface of walls,floors etc complete all as specified and as directed by the Engineer-in-Charge.

M&L for point wiring using approved colour coding as per IS (Red , Black and Green for single phase circuits),with multistranded copper conductor 2.5 sq mm nominal cross-sectional area , single core, PVC insulated and unsheathed FRLSH cable 1100 Volts grade, ISI-694 marked with valid CML No.in and inciuding medium grade, PVC casing caping/surface conduit and accessories on wall/roof/floor etc, ISI marked with mild steel/pressed steel sunken box thickness as per IS standard (with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally. and two coats of black bituminous paint over a coat of red oxide primer externally,covered with 3 mm thick plastic laminated sheet cover for fixing of switches, socket and fan regulators etc, inciuding PVC insulated multistranded copper conductor 2.5 sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly for One light or fan point, controlled by one, one way switch 5 Amps complete all as specified and directed by Engineer-in-charge. Notes: (i) Switches socket,regulators shall be measured and paid for separately.(ii) Cost of metal flush boxes & modular cover plate shall be included under this item.

All as per item No. 211.00 above here in before One light point controlled by 2- way switches, with cables 1.5 sqmm size.complete all as specified and as directed by Engineer-in charge.

All as per item No. 211.00 above but one 5 Amps 3/5 pin socket outlet on the same board with other switches complete all as specified and directed.

All as per item No.211.00 above but one 5 Amps 3/5 pin socket outlet on independent board complete all as specified and directed.

All as per item No. 211.00 above but wiring with 2.5 sqmm PVC insulated and unsheathed FRLS single core multistranded copper cables incl 1.5 sqmm PVC insulated and unshesthed FRLS copper earth wire with for one 3 pin 5/15 Amps switch socket outlet on independent board complete all as specified and directed.

All as per item No. 211.00 above but wiring with 4 sqmm copper cables with 4 Sqmm copper cable as continuous earth wire for one 5/15 Amps switch socket outlet on independent board.

M&L for point wiring using approved colour coding as per IS (Red , Black and Green for single phase circuits),with multistranded copper conductor 2.5 sq mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLSH cable 1100 Volts grade, ISI-694 marked with valid CML No. and into Existing PVC Concealed conduit of 20 mm bore with accessories in wall floor etc with 3 mm thick plastic laminated sheet cover for fixing of switches, sockets and fan regulators etc, inciuding PVC insulated multistranded copper conductor 2.5 sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed by Engineer-in-charge for One light or fan point, controlled by one, one way switch 5 Amps. Make of wire : FINOLEX/Havells/Polycab

All as per item No 217.00 here-in-before but one 5 Amps 3/5 pin socket outlet on the same board with other switch complete all as specified and directed.

All as per item No 217.00 here-in-before but one 5 Amps 3/5 pin socket outlet on independent board complete all as specified and directed.

All as per item No. 217.00 here-in-before but wiring with 4 sqmm copper cables with 4 Sqmm copper cable as continuous earth wire for one 5/15 Amps switch socket outlet on independent board complete all as specified and directed.

S&F switch piano, flush button, 5/6 Amps single pole, one way, 230 Volts.complete including taking down old all as specified and as directed by Engineer-in charge.

S&F Switch piano, flush button, 5/6 Amps, single pole, two way, 230 Volts complete including taking down old all as specified and as directed by Engineer-in charge.

S&F socket outlet, 3/5 pin, 5 Amps, flush type. complete including taking down old all as specified and as directed by Engineer-in charge.

S&F switch socket(2-in-1) combination, 3/5 pin, 5 Amps, flush type. complete including taking down old complete all as specified and directed by Engineer-in-charge

S&F Switch socket combination multi-purpose 3pin, 15 Amp and 3 pin, 5 Amps complete including taking down old complete all as specified and directed by Engineer-in-charge

S&F Ceiling rose surface bakelite 65x50 mm, two to three terminals.complete including taking down old complete all as specified and directed by Engineer-in-charge

S & F in repair Bell push,flush type,5 Amp. including taking down old complete all as specified and directed by Engineer-in-charge

M&L Point wiring used approved colour coding as per IS (Red, Black and Green) for single phase circuits), with multi-stranded copper conductor 2.5 sqmm nominal cross -sectional area, single core, PVC insulated and unsheated FRLS cable 1100 volts grade, ISI 694 marked with valid CML No. and existing PVC Concealed conduit of 20 mm bore including medium grade, PVC concealed conduit MMS, ISI marked of dia not less than 20 mm and conduit accessories conceled in wall/roof/floor etc, ISI marked with valid CML No. (IS-9537 - 1983 for condits and IS : 3419 - 1976 for conduit accessories) with terminated to new pressed flush metal boxes readily available cover with outer plates inner plates et, suitable for mounting modular type switches, socket fan regulator etc PVC insulated multistanded copper conductor 2.5 Sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for the following :- Note : Modular switch and socket shall be measured and paid separately.

All as per item No. 228.00 above here in before One light point controlled by 2- way switches, with cables 1.5 sqmm size.complete all as specified and as directed by Engineer-in charge.

All as per item No. 228.00 above but one 5 Amps 3/5 pin socket outlet on the same board with other switches complete all as specified and directed.

All as per item No.228.00 above but one 5 Amps 3/5 pin socket outlet on independent board complete all as specified and directed.

All as per item No. 228.00 above but wiring with 2.5 sqmm PVC insulated and unsheathed FRLS single core multistranded copper cables incl 1.5 sqmm PVC insulated and unshesthed FRLS copper earth wire with for one 3 pin 5/15 Amps switch socket outlet on independent board complete all as specified and directed.

All as per item No. 228.00 above but wiring with 4 sqmm copper cables with 4 Sqmm copper cable as continuous earth wire for one 5/15 Amps switch socket outlet on independent board.

S&F in repair of Switch modular 06 A 01 module , one way as per existing pattern complete all as specified and directed by Engr-In-Charge.

S&F in repair of of modular Socket outlet, multi purpose, 06 Amps 3 pin combined 2 module as per existing pattern complete all as specified and directed by Engr-In-Charge.

S&F in repair of modular Bell push 06 Amps 1 module as per existing pattern complete all as specified and directed by Engr-In-Charge.

S&F in repair of modular Socket 16 Amps, 5 pin combined 2 module as per existing pattern complete all as specified and directed by Engr-In-Charge.

S&F ir repair of modular Switch 16 Amps one way 1 module as per existing pattern complete all as specified and directed by Engr-In-Charge.

S&F in repair of Switch modular 06 Amps two way, 1 module as per existing pattern complete all as specified and directed by Engr-In-Charge.

S&F in repair of modular fan regulator 5 step type, 2 module as per existing pattern complete all as specified and directed by Engr-In-Charge.

S&F in repair of modular white cover plate with frame inner and outer plates for following sizes:-

(a) 2 modules

(b) 3 modules

(c) 4 modules

(d) 6 modules

(e) 8 modules

S & F in repair electronic dimmers, 450 W, 250 V flush type on the existing phenolic laminated sheet etc all as specified and as directed.

S & F in repair bell Ding Dong AC,230 volts,single pole. including taking down old complete all as specified and as directed.

M & L in repair for LED light fitting,1x10 watt bulk head luminaries polycarbonate body heat resistant prismatic glass cover with specially designed gasket including LED 1 x10 Watts SMD after taking down old unservicable light fitting of any description LED light including driver holder connecting up ith three core flexible copper conductor cable of suitable size complete all as specified and directed

Supply and fixing of LED box type Integrated Batten Wattage 20 watt having Aluminum Extruded housing in white powder coated Finish with high translucent PC Cover, Dimension of the Fixture Must not be less Then Length 1170 MM (± 5 MM ), Elegant Design, IP 20 Protection. Minimum Lumens output of the fitting shall be 2500 Lumens With Efficacy of 125 lm/W, CCT 5700 – 6500K, Surge Protector 4 KV, PF>= 0.95 , Necessary mounting arrangements. The Manufacturer of the fixture shall have in house NABL Accredited Lab and must produce certificate of the same along with LM-79 / LM-80 / Test Report. connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed by Engr-in-Charge.

S & F LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver, holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer-in-charge.

M&L in repair of lamp holder, PVC/ polycarbonate type with back plate suitable for batten fittings including taking down unserviceable lamp holder of any description complete all as specified and directed.

S&F in repair PVC rectangular block of size 10cm x 10cm x 5 cm depth for mounting switches sockets, fan regulators etc with 3 mm thick laminated sheet cover including taking down old one complete all as specified and as directed by Engineer-in charge.

S&F in repair PVC board of size 17.5cm x 10cm x 5 cm depth for mounting switches sockets, fan regulators etc with 3 mm thick laminated sheet cover including taking down old one complete all as specified and as directed by Engineer-in charge.

S&F in repair PVC board of size 20cm x 15cm x 5 cm depth for mounting switches sockets, fan regulators etc with 3 mm thick laminated sheet cover including taking down old one complete all as specified and as directed by Engineer-in charge.

S&F in repair PVC board of size 25cm x 20cm x 5 cm depth for mounting switches sockets, fan regulators etc with 3 mm thick laminated sheet cover including taking down old one complete all as specified and as directed by Engineer-in charge.

S&F in repair PVC board of size 35 cm x 30 cm x 5cm depth for mounting switches sockets, fan regulators etc with 3 mm thick laminated sheet cover including taking down old one complete all as specified and as directed by Engineer-in charge.

M&L for submain wiring with approved colour code/as per IS (Red, black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper coductor of nominal cross sectional area of 4.0 Sq mm (FRLS) in and including PVC casing & capping non metallic including one run of PVC insulated multistranded copper conductor nominal cross section area of 4.0 Sq mm (FRLS) of continuous earth wire green in colour including taking down old u/s sub-main wiring complete all as specified and directed by Engineer-in-charge. (NOTE: Two runs of 6.0 sqmm cable & One run of 6.0 sqmm cable and One run of PVC casing & capping shall be paid as one unit length.) Note:(i) Two different colour wires shall be used for phase and neutral. (ii) Connections of cables with MCBs or Bus Bar shall be done through appropiate size brass/copper thimbles. (iii) if necessary cutting chasing shall be included in this item.

M&L for submain wiring with approved colour code/as per IS (Red, black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper coductor of nominal cross sectional area of 6.0 Sq mm (FRLS) in and including PVC casing & capping non metallic including one run of PVC insulated multistranded copper conductor nominal cross section area of 6.0 Sq mm (FRLS) of continuous earth wire green in colour including taking down old u/s sub-main wiring complete all as specified and directed by Engineer-in-charge. (NOTE: Two runs of 6.0 sqmm cable & One run of 6.0 sqmm cable and One run of PVC casing & capping shall be paid as one unit length.)

M&L for submain wiring with approved colour code/as per IS (Red, black & green for single phase) circuit with two single core PVC insulated cable with multistranded copper coductor of nominal cross sectional area of 10.0 Sq mm (FRLS) including PVC conduit non metallic including one run of PVC insulated multistranded copper conductor nominal cross section area of 10.0 Sq mm (FRLS) of continuous earth wire green in colour including taking down old u/s sub-main wiring complete all as specified and directed by Engineer-in-charge. (NOTE: Two runs of 10.0 sqmm cable & One run of 10.0 sqmm cable and One run of PVC casing & capping shall be paid as one unit length.) Note : (i) Two different colour wires shall be used for phase and neutral. (ii) Connections of cables with MCBs or Bus Bar shall be done through appropiate size brass/copper thimbles. (iii) if necessary cutting chasing shall be included in this item.

M&L sub main wiring surface type/ concealed type as required at site with two runs of single core, PVC insulated, unsheathed multi standard copper conductor cable of size 4 Sqmm, 1100 volts grade (FRLS) and one run of 4 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through and including suitable size ISI marked rigid PVC conduit with all necessary accessories such as bends, tees, junction boxes, elbows complete all as specified and as directed. (Note :- Two runs of 4 Sqmm cable, one run of 4 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length).

M&L sub main wiring surface type/conealed type as required at site with two runs of single core, PVC insulated, unsheathed multi standard copper conductor cable of size 6 Sqmm, 1100 volts grade (FRLS) and one run of 6 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through and including suitable size ISI marked rigid PVC conduit with all necessary accessories such as bends, tees, junction boxes, elbows complete all as specified and as directed. (Note :- Two runs of 6 Sqmm cable, one run of 6 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length). Note:(i) Two different colour wires shall be used for phase and neutral. (ii) Connections of cables with MCBs or Bus Bar shall be done through appropiate size brass/copper thimbles. (iii) if necessary cutting chasing shall be included in this item.

M&L sub main wiring surface type/conealed type as required at site with four runs of single core, PVC insulated, unsheathed multi standard copper conductor cable of size 10 Sqmm, 1100 volts grade (FRLS) and one run of 10 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through and including suitable size ISI marked rigid PVC conduit with all necessary accessories such as bends, tees, junction boxes, elbows complete all as specified and directed by Engineer-in-charge. (Note :- Four runs of 10 Sqmm cable, one run of 10 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length). Note : (i) Two different colour wires shall be used for phase and neutral. (ii) Connections of cables with MCBs or Bus Bar shall be done through appropiate size brass/copper thimbles. (iii) if necessary cutting chasing shall be included in this item.

SS&F in repair factory made Load line distribution board in sheet steel enclosure with bus bar SPN, 2 way, IP 43 ,240 Volts suitable for fixing MCBs including necessary earth bus bar and neutral link 200 amp and complete with provision of MCB(outgoing) with adjustable release complete fixed in repair complete all as specified and as directed by Engineer-in charge.

&F in repair factory made Load line distribution board in sheet steel enclosure with 200 Amps rated bus bar SPN, 4 way double door 240 Volts suitable for fixing MCB including necessary earth bus bar and neutral link 200 amp and complete with provision of MCB(outgoing) with adjustable release complete fixed in repair complete all as specified and as directed by Engineer-in charge.

S&F in repair factory made Load line distribution board in sheet steel enclosure with 200 Amps rated ,IP 43 bus bar SPN, 8 way double door powder coated sheet metal enclosure 240 Volts suitable for fixing MCB including necessary earth bus bar and neutral link 200 amp and complete with provision of MCB(outgoing) with adjustable release complete fixed in repair complete all as specified and as directed by Engineer-in charge.

S&F in repair factory made Load line distribution board in sheet steel enclosure with 200 Amps rated bus bar VERTICAL TPN, IP 43, 4 way double door powder coated sheet metal enclosure 240 Volts suitable for fixing MCB including necessary earth bus bar and neutral link 200 amp and complete with provision of MCB(outgoing) with adjustable release complete fixed in repair complete all as specified and as directed by Engineer-in charge.

S&F MCB, SP, 240 Volts, 5 to 32 Amps. 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single pole in the MCB DB complete all as specified and as directed

S&F MCB, SPN, 240 Volts, 5 to 40 Amps. 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single pole and neutral in the MCB DB complete all as specified and as directed

S&F MCB, TPN, 415 Volts, 40 to 100 Amps., 10 KA 'C' curve miniature circuit breaker (MCB) of triple pole and neutral in the MCB DB complete all as specified and as directed

S&F as in repair MCB, SP, 240 Volts, 5 to 32 Amps. 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single pole fixing in the MCB DBs complete including proper thimble connection complete all as specified and as directed

S&F as in repair MCB, SPN, 240 Volts, 5 to 32 Amps. 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single pole and neutral fixing in the MCB DB complete including proper thimble connection complete all as specified and as directed.

S&F as in repair MCB, SPN, 240 Volts, 40 to 63 Amps. 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single pole and neutral fixing in the MCB DB complete including proper thimble connection complete all as specified and as directed.

S&F as in repair MCB, TPN, 415 Volts, 16 to 32 Amps., 10 KA 'C' curve miniature circuit breaker (MCB) of triple pole and neutral fixing in the MCB DB including proper thimble connection complete all as specified and as directed.

S&F as in repair MCB, TPN, 415 Volts, 40 to 100 Amps., 10 KA 'C' curve miniature circuit breaker (MCB) of triple pole and neutral fixing in the MCB DB complete including proper thimble connection complete all as specified and as directed.

Supply and fix single pole and neutral enclosures with a two pin and earth plug and socket complete with one double pole MCB 20 A ,240 V complete all as specified and directed by Engineer-in-charge

Taking down ceiling fan/exhaust fan and dismantling blades and removing fan and blades to store complete all as specified and directed by Engineer-in-charge

Supply and fix ceiling fans, complete with blades, down rods, electronic regulator and accessories 230V, 1200 mm sweep, min air delivery 210 CFM with service value 6.00 BEE five star rated with brushless direct current motor (BLDC) complete all as specified and directed by Engineer-in-charge

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete including connecting with 3 core flexible copper conductor including taking down the existing exhaust fan and depositing the same in MES store complete all as specified and directed by Engineer-in-charge

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 250mm complete including connecting with 3 core flexible copper conductor including taking down the existing exhaust fan and depositing the same in MES store complete all as specified and directed by Engineer-in-charge

Material & Labour in replacement of Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thickness burried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00mm dia by means of nuts & bolts, check nuts and washers of galvanised incl PCC pit of 1:2:4 type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, earth pit angle iron frame of size 25mm x 25mm, excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire -mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected main switch board all as specified and testing on completion complete all as specified and directed by Engineer-in-charge.

National Rewinding Works (BID ID -3182926)

M/S Tanisha Traders (BID ID -3182973)

M/s godara infratech and power industries (BID ID -3182241)

M/s SK Traders (BID ID -3180931)

SANJOLI CONSTRUCTION COMPANY (BID ID -3183098)

RISING ELECTRICALS (BID ID -3183208)

M/s. Ambabhai K patel (BID ID -3182775)

Rasam Engg Co. (BID ID -3183324)