REPAIR REPLACEMENT OF ROOFSHEET ROOF TREATMENT SUNKEN AND CERTAIN OTHER RELATED WORKS AT OFFR MD ACCN IN SOMNATH ENCLAVE AND 108 COMPO SIG DET SATA BTY VIKRAM BATRA VIHAR ETC UNDER AGE BR II OF GE SUKNA

Amount

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Burnt Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:6 complete all as specified and directed.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting not exc. 10 cm in girth complete all as specified and directed .

M&L 18-20 mm thick granite as in counter basin (table rubbed and polished) laid over and including screed bed 15 mm thick in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and including demolition of the existing slab complete all as specified and directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement complete all as specified and directed.

S & F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side and covered on both side with decorative face veneer with liping/frame to match complete all as specified and directed.

S&F 35 mm thick flush door shutters solid core construction, with MDF and plywood face panels, commercial type on both side and covered on both sides complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down and refixing in the same opening shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wire gauze in lieu of plain colour PVC sheet. The wire gauze shall be wrapped on an additional square 8mm MS Solid tube and this tube shall be welded to MS tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 5 mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 5 mm thick PVC insulation panel with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling including GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n. exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel at 457 mm centre to centre and necessary hangers 6 mm dia GI fixed to roof and including dismantling complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S & F 100 mm long medium weight, cold rolled mild steel Butt hinges with screws complete all as specified and directed.

S & F 300 mm long ordinary rat tail pattern springs including roller and roller plate complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 140 mm complete all as specified and directed.

S&F in repairs Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width of and of weight between 61 to 80 Kg. (extruded section) complete all as specified and directed.

S & F in repairs Galvanized mild steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples including wooden beads complete all as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

Supply and fixing Magnetic catch of approved quality 75 mm size complete all as specified and directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks, wire clothes and similar work conforming to Fe-290 Gde-165, complete all as specified and as directed.

S&F Roof truss (framed) trussed, purlins,crane gantires of steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1998 grade St-240 including one shop coat of zink chrome primer complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dove-tailed or welded complete all as specified and directed.

S&F steel ventilator with top hung shutter and including hinges steel peg stay complete all as specified and directed.

S & F pressed steel frame of size 105 x 60 mm for doors with one or more rebates including filling of cement mortar or cement concrete necessary fixing lugs, hinges, lock strike plates, and two coat of synthetic enamel paint over one coat of red oxide etc complete all as specified and directed

S & F pressed steel frame of size 125 x 60 mm for doors with one or more rebates including filling of cement mortar or cement concrete necessary fixing lugs, hinges, lock strike plates, and two coat of synthetic enamel paint over one coat of red oxide etc complete all as specified and directed

S&F Powder coated aluminium frame (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F non asbestos fibre cement building boards 4 mm thick E-Board (designer pattern) fixed or laid / inserted to GI framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and including GI frame work comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with contacting clips across the intermediate channel at 457 mm centre to centre hanging from structural steel / scantling with 6 mm GI wire and including dismantling complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F in repairs 18/19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination and other side balancing white laminated fixed with screw to timber / aluminium frame work complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in sub base, floors, paths, plinth protection, hardstanding etc complete all as specified and directed.

M&L 75 mm thick, PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub floor, sub base of floor, etc complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 8-10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick backing in CM 1:3 complete all as specified and directed.

M&L Coloured glazed ceramic tiles 350x 250x 7 mm/ 450X 350X 7mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 cm thick backing with cm 1:3 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 20 mm thick in CM 1:6 finish even and rough complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, as in skirting/dado on vertical surfaces over etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 10 mm thick in CM 1:3 complete all as specified and directed.

M&L pre polished cement concrete chequered tiles 300 x 300 x 25 mm thick with grey cement with pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 fnished even and fair complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement using WPC compound complete all as specified and directed. Note:- WPC shall be measured and paid separatley.

M/L 10 mm thick cement plaster in CM (1:3) using WPC @ 3% by wt of cement in sunken portion complete all as specified and directed. (Note-WPC will be measured and paid separately)

M&L for rendering 5 mm thick in CM 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L preparation of old decorated wall surfaces by brooming down or steel wire brushing scraping down smoke spot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of white wash complete all as specified and directed.

M&L preparation of old decorated ceiling surfaces by brooming down or steel wire brushing scraping down smoke spot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying one coat of white wash complete all as specified and directed.

M & L for preparation of newly plastered or previously untreated surfaces of walls and applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty to obtain smooth finish complete all as specified and directed.

M&L complete removal of existing treatment of old decorated wall surfaces and including applying two coats of oil bound distemper over a coat of primer and over a thin layer of wall care putty complete all as specified and directed.

M&L for prepration of new plastered ceiling surfaces and applying two coat of oil emulsion distemper over a coat of primer over a thin layer of wall care putty complete all as specified and directed.

M&L preparation of old decorated wall surface and including applying one coat of oil bound distemper complete all as specified and directed.

M&L preparation of old decorated ceiling surface and including applying one coat of oil bound distemper complete all as specified and directed.

M&L preparation of old plastered wall surfaces and inlcuding applying two coats of weather coat exterior paint over a coat of primer complete all as specified and directed.

M&L preparation of old plastered wall surfaces and including applying one coat of cement base paint in maximum 3 storage bldg complete all as specified and directed. Note : Rate shall be included for necessary scaffolding and safety arrangement.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S&F 4.8 mm thick glass including tinted/dark film n.exc 0.5 sqm each pane complete fixed to aluminium frame work including rubber beading complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from steel/wooden frames or stones, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed.

M&L preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

M&L preparation of old decorated steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying one coat of synthetic enamel paint complete all as specified and directed.

M&L preparation of new steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, in walls / ceiling or in floors etc. complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections, in walls / ceiling or in floors etc. complete all as specified and as directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 25 mm bore galvanised steel water tubing medium grade as sprout pipe fixed in wall etc complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 500 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of 500 ltr to 1000 ltr capacity PVC water storage tank without dismantling the tank incl writting the item "Tank Cleaning on ____" indication the date, month & year of cleaning on external wall of tanks walls with synthetic enamel paint all as specified and directed by Engr -in-charge.

S & F in repair 15 mm bore bib tap chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs pillar tap 15 mm bore, fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F in repair 15 mm bore stop cock / angle cock fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S&F in repair angle stop valve 15 mm bore, cast copper alloy, screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe or unions and fixed, fancy type, concealed type, chromium plated long shank with flange complete all as specified and directed.

S&F in replacement 15 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in replacement 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F in repairs 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F in repair 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F PVC (SWR) Floor trap of 75 mm outlet plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repairs soap dish, with metal dish brass chromium plated fixed to plugs complete all as specified and directed.

S&F in repairs vitreous china squatting pan, "Orissa pattern" white, size 580 x 440 mm with integral foot rest, 'P' or 'S' trap and including connection to trap and to flushing pipe including provn of lime concrete holding CI anti -syphonage pipe complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair swivel shower rose size 125 mm of brass chromium plated any colour (minimum weight 40 gms) for fixing with 15mm dia steel pipe complete all as specified and directed.

S&F in repair brass chromium plated toilet paper holder flat recessed type fixed to walls with chromium plated brass screws complete all as specified and as directed.

S&F as in repair Health faucet of CP 15mm bore fancy type and with 1 mtr long and jet shower easy flex tube in chrome finish and wall hook including CP nipple with socket complete all as specfied and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

Dismantling wall and ceiling boards, partitions of any description or in any position (fibre, pulp, insulation etc.) any thickness, or insulation boards/ slabs/ blankets of any thickness including cover fillets complete all as specified and directed.

M&L for roof treatment in order of precedence as given below complete all as specified and as directed:- (i) Taking out of existing water proofing treatment and including padding, cleaning the surface using wire brush, brooming down and washing down with water to remove dust etc, and brushing with neat cement slurry @ 3.00 kg of cement per Sqm. (ii) 15 mm thick screed bed in CM 1:4 on surface. (iii) Cleaning of plastered surface and applying one coat of bituminous primer @ 0.40 Ltr / Sqm. (iv) Supply and laying 3 mm (Minimum) thick APP based polymeric membrane of approved manufacturer with weight not less than 3.60 Kg per Sqm, reinforced with non-woven polyester fabric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height of 30 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (Cont.)

(v) Applying one coat of water proofing paint with aluminium finish over APP as per manufacturer's instruction. Note :- (a) Bituminous primer shall be "ShaliTex Primer" manufactured by M/s STP Ltd or equivalent in M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (b) Laying APP based polymeric membrane shall be done by torch on method as per manufactures instructions. (c) A minimum overlap of 100 mm and 75 mm should be made at the end and sides of the polymeric membrane respectively and all overlaps and joints shall be sealed as per manufacturers instruction.

M&L PCC 1:2:4 type B-I (Using 20 mm graded crushed stone aggregate) as in roof kerbs, rounded or chamfered on edges gap between roof sheets and brick walls, thickness of concrete bed exc 5 cm and not exe 10 cm thickness and not exe. width of one brick wall thickness including necessary scaffolding and formwork ht up to 7 m complete all as specified and directed

S&F 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as specified and directed.

S&F factory made 28mm thick soild PVC flush door shutter made from co-exturded 3 layer rigid PVC foam sheet (single extruded) water proofing and termite proof and fire retardent having density 600 kg/cum (minimum) outer layer 0.8 to 1mm thick of rigid PVC with density 1400kg/cum complete all as specified and as directed.

M&L for Prepration of new wall surfaces, applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & ungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces over not less than 1 mm thick putty all as specified and directed

M&L for Applying evenly a bitumen tack coat of industrial bitumen 85/25 @ 1.2 kgs/Sqm including cleaning surfaces complete all as specified.

M&L providing APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150gms/Sqm) land on primed surfaces by forced application APP based polymeric membrance complete all as specified and directed by Engineer-in-Charge.

R K UDYOG (BID ID -3237225)

S D CONSTRUCTION CO (BID ID -3237186)

A K ENTERPRISES (BID ID -3237131)

ROXEE CONSULTANT (BID ID -3237175)

MS ESSCON (BID ID -3236953)

M/S EASTERN ENGINEERING (BID ID -3237184)

VICKY ENTERPRISES (BID ID -3236735)

D K SARKAR (BID ID -3237212)

B.B. Enterprise (BID ID -3237235)