Renovation and repair of sprinkler works of 21 diggies (CCA 4139.45 hectare) Manderpura Minor, Bhomiyaji Minor, Chanderi Minor and Hameerdesar Minor of Ch. K. R. A. Lift Canal System under the jurisdication of S and I Lift Sub Division-II, IGNP,

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5 m , disposed earth to be levelled and neatly dressed : All kinds of soil ( PWD Building BSR 2022, Ch- B1, Item no- 1.6

Providing and Laying in position of Cement concrete Nominal mix (1:3:6) including leads of all construction materials, curing, compaction and finishing with rendering in cement sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. Well graded crusher broken stone aggregate of maximum size upto 40mm. (IGNP BSR 2023-24 Ch-IX, item 8-c)

Brick masonry (using well burnt clay bricks of size 230x110x70mm, class designation 75 as per specification) up to plinth including all leads of all construction materials including curing etc. complete In cement sand mortar 1:5. (IGNP BSR 2023-24 Ch-VII, item 10-C) + Add extra if well burnt clay bricks (size 230x110x70 mm) class designation 100 as per specifications are to be used (IGNP BSR 2023-24 Ch-VII, item 14-a), (Comlete Rate - 5767.00 + 490.36 = 6257.36)

Providing and Laying in position of Cement concrete Nominal mix (1:2:4) including leads of all construction materials, curing, compaction and finishing with rendering in cement sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. Well graded crusher broken stone aggregate of maximum size upto; 20 mm (IGNP BSR 2023-24 Ch-IX, item 8-d)

Brick masonry (using well burnt clay bricks of size 230x110x70mm, class designation 75 as per specification) up to plinth including all leads of all construction materials including curing etc. complete In cement sand mortar 1:5. (IGNP BSR 2023-24 Ch-VII, item 10-C) + Add extra if well burnt clay bricks (size 230x110x70 mm) class designation 100 as per specifications are to be used (IGNP BSR 2023-24 Ch-VII, item 14-a), + Add extra for superstructure brick masonry on item no 10 (IGNP BSR 2023-24 Ch-VII, item 13) (Comlete Rate - 5767.00 + 490.36+212 = 6257.36)

Centering and shuttering for slabs, beams, lintels Columns, trough with or without caps and base including propping and removing . (IGNP BSR 2023-24 Ch-X, item 2)

Providing and Laying in position of Cement concrete Nominal mix (1:1.5:3) including leads of all construction materials, curing, compaction and finishing with rendering in cement sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. Well graded crusher broken stone aggregate of maximum size upto; 20 mm (IGNP BSR 2023-24 Ch-IX, item 6-d)

Supplying of M.S. reinforcement including labour charges for bending binding and placing in position all reinforcement as per drawing including cost of binding wire and all leads and lifts using.Tor or ribbed bars (IS :1786) (IGNP BSR 2023-24 Ch-X, item 9-b-ii)

Providing and laying cement concrete coping in (1:2:4) with maximum size of crusher broken aggregate upto 20 mm including shuttering etc. with all leads of material complete in all respect in thickness of 75 mm (IGNP BSR 2023-24 Ch-XVIII, item 17-a)

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as require including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. (PWD BSR ch B-9 item no. 9.5)

Providing and fixing M.S. sheet 1mm thick single leaf door shutter in angle iron frame 35x35x5mm suitabilly diagonally braced with 25x3mm flat iron above and below lock rail of size 50x5mm beading extra including all fittings, as per direction of Engg. incharge but excluding cost of chowkhats: including two coats of anit-corrosive red oxide primer paint (PWD BSR ch B-9 item no. 9.17)

Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. (PWD BSR ch B-9 item no. 9.26)

Plaster in cement sand mortar 1:5 including racking of joints, smooth finishing & curing etc. complete including all leads of all construction materials of thickness 12 mm (IGNP BSR 2023-24,Ch-VIII, item 3-b)

Providing and Laying in position of Cement concrete Nominal mix (1:4:8) including leads of all construction materials, curing, compaction and finishing with rendering in cement sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. Well graded crusher broken stone aggregate of maximum size upto; 20 mm, (IGNP BSR 2023-24 Ch-IX, item 9-d)

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete. (PWD BSR ch B-11 item no. 11.3.1)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work, (PWD Building BSR 2022 item 12.46.1 Ch B-12)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:New work (two or more coats) over and including scrapping and priming coat with cement primer. (PWD Building BSR 2022 item 12.37.1 Ch B-12)

Finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding: New work (Two or more coats applied @ 3.84 kg/10 sqm). (PWD Building BSR 2022 item 12.37.1 Ch B-12)

P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2 .) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant.110mm dia (PWD Building BSR- 2022, Ch S-3 item no. 3.16.3)

Construction of Soakage well in all types of soil of approved drawing, top 90 Cm .Portion in 450mm thick masonry with CM 1:6, 80 mm thick stone slab covering, jointing of slab in CM 1:3 ,Ralthal, kharanja 40mm thick M-15 grade C.C flooring, earth work etc . complete including disposal of surplus earth within a lead of 50 mtr , Inner dia 90 Cm & 10 to 12 Mtr deep. (PWD Building BSR ch S-3 item no. 3.24.1)

P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: Size 530x410mm. (PWD Building BSR ch S-1 item no. 1.2.1)

P & F PVC Storage Tank ISI Marked (IS : 12701) indicating the BIS license No), of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 500 litres capacity. (PWD Building BSR ch S-2 item no. 2.26.3)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,)thikness 20mm, (PWD Building BSR- 2022 Ch S-2 item no. 2.38.2)

P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make:C.P. Brass bib cock,15mm nominal bore. PWD Building BSR- 2022, (Ch S-2 item no. 2.7.3

P & F Flush Cock / Flush Valve (IS : 9758 Mark) for WC of approved quality make :CP brass push type 15mm nominal bore.(Ch S-2 item no. 2.14.1)

P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make :Gun-metal 15mm nominal bore. (Ch S-2 item no. 2.15.1)

Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) inrecessed ISI marked ( IS:9537 P - II ) rigid steel conduit & it's ISI marked (IS:14768 P-II 2003) accessories, round tiles,Hot Dipped Galvanized Modular Box of 1.2 mm thick with earth terminal,10A Modular switch,3 pin ceiling rose / holder / 3 way connector ,Modular face plate with grid plate, pvc bushes, check nuts, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR PWD BSR Electrical Works 2022 ch-2 Short point (up to 3 mtr.) 2.1.1

Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) inrecessed ISI marked ( IS:9537 P - II ) rigid steel conduit & it's ISI marked (IS:14768 P-II 2003) accessories, round tiles,Hot Dipped Galvanized Modular Box of 1.2 mm thick with earth terminal,10A Modular switch,3 pin ceiling rose / holder / 3 way connector ,Modular face plate with grid plate, pvc bushes, check nuts, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR PWD BSR Electrical Works 2022 ch-2 Medium point (up to 6 mtr.) 2.1.2

Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) inrecessed ISI marked ( IS:9537 P - II ) rigid steel conduit & it's ISI marked (IS:14768 P-II 2003) accessories, round tiles,Hot Dipped Galvanized Modular Box of 1.2 mm thick with earth terminal,10A Modular switch,3 pin ceiling rose / holder / 3 way connector ,Modular face plate with grid plate, pvc bushes, check nuts, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure 'A' attached with this BSR PWD BSR Electrical Works 2022 ch-2 Long point (up to 10 mtr..) 2.1.3

Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulb in existing holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70, minimum life time of minimum 25000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing.OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . foe additional technical parameters of product/ work, refer Annexure "A" attacheded with this BSR. 15WATT (PWD BSR electrical works 2022 ,CH. E-17, Item 17.9.3)

Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in existing surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 2 x 2.5 sq.mm PWD BSR electrical works 2022 CH. E-4, Item 4.1.6

Supplying and fixing of power plug point with Modular accessories as per PWD specification for electrical Works, on hot dipped galvanized modular box of 1.2 mm thick with earthing terminal/connector on surface or inrecessed with suitable size of modular face place with grid plate and cover plate including cost of ISI marked modular 16 amp. Switch (IS :3854) and 6/16 amp. socket outlet (IS:1293) making connection , testing , etc. as required. For specification of Wiring accessories refer Chapter E - 07 related item & For additional technical parameters of product / work refer Annexure 'A' attached with this BSR PWD BSR electrical works 2022 CH. E-7, Item 7.37

Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printed made out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating ,including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 5 step fan regulator 2 Module 360 dgree rotating, PWD BSR electrical works 2022 CH. E-7, Item 7.29.1

Providing & Fixing of modular type switch/ bell push duly ISI marked (IS:3854) with CM/L no. printed and made out of unbreakable and fire retardant vergin UV Stabilized Polycarbonate with brass terminals and captive screws & silver alloy contact tip with IP-20 rating ,minimum width of switch toggle( PUSH PART ) should not less then 20mm, including all as per pre approved by Engineer in charge,making connections, testing etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 16 A one way switch With Led Indicator 113.0 PWD BSR electrical works 2022 CH. E-7, Item 7.27.4

Providing & Fixing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) PWD BSR electrical works 2022, CH. E-15, Item 15.7.3

Providing & Fixing of ISI marked (IS:1258) batten/angle lamp holder with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal & captive screwsincluding making connection testing etc. as required. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work , refer Annexure "A" attached with this BSR PWD BSR electrical works 2022 CH. E-7, Item 7.13

Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947- 2, low watt losses, trip free mechanisum , energy limiting of class 3as per IEC, minimum phase termination capacity of 35sq.mm. ,conductor line load reversibility , IP 20 contact protection and fittedin existing distribution board/sheets, minimum electrical operation20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A &above rating including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab typetest reports & All as per pre approved by Engineer in charge. Foradditional technical parameters of product / work refer AnnexureA' attached with this BSR (40 A rating) PWD BSR electrical works 2022 CH. E-6, Item 6.1.2.3

Providing and Laying in position of Cement concrete Nominal mix (1:3:6) including leads of all construction materials, curing, compaction and finishing with rendering in cement sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints excluding the cost of centering, shuttering and reinforcement. Well graded crusher broken stone aggregate of maximum size upto 20mm. (IGNP BSR 2023-24 Ch-IX, item 8-D)

Side shuttering including propping etc. complete (to achieve finish F 2 for : Top or intermediate bed plates, in between masonry or piers, abutments sluice wells etc. (IGNP BSR 2023-24 Ch-X, item 1.2)

Canal lining with hydraulic compressed pre-cast slab of cement concrete M15 tiles of size 300 x 150 x 40 mm laid over 12 mm (av.) thick subgrade cement plaster in CM (1:6) , 16 mm thick jointing sandwich plaster in CM 1:3 and 6 mm thick jointing mortar in cement mortar (1:3) etc. including curing and all leads& lift of all construction materials complete in all respect in bed (IGNP BSR 2023-24 Ch-IX, item 25.1)

Canal lining with hydraulic compressed pre-cast slab of cement concrete M15 tiles of size 300 x 150 x 40 mm laid over 12 mm (av.) thick subgrade cement plaster in CM (1:6) , 16 mm thick jointing sandwich plaster in CM 1:3 and 6 mm thick jointing mortar in cement mortar (1:3) etc. including curing and all leads& lift of all construction materials complete in all respect in side (IGNP BSR 2023-24 Ch-IX, item 25.2)

Providing, Laying and spreading of HDPE geomembrane confirming to ISspecifications, onsubgrade including jointing and cost of jointing material.HDPE 300 Micron (WR HMH BSR 2023-24 Ch-VII, item 21.1.2)

Excavation including loading, unloading, disposal and dressing of excavated earth within initial lead of 50m and lift up to 1.5m including dressing of excavated area and dewatering wherever required complete in Soft/Loose soil (IGNP BSR 2023-24 Ch-V, item 1)

Half Brick masonry (using well burnt clay bricks of size 230 x 110 x 70 mm, class designation 75 as per specification) for partition wall including all leads of all construction materials including curing etc. complete. In cement sand mortar 1:4 (IGNP BSR 2023-24 Ch-VII, item 11-b) + Add extra if well burnt clay bricks (size 230x110x70 mm) class designation 100 as per specifications are to be used (IGNP BSR 2023-24 Ch-VII, item 14-b) (Comlete Rate - 724 + 50.73 = 774.73)

10 mm thick Cement plaster in cement mortar (1:4) as per design and specification including cost of all materials including mechanical mixing of mortar with all leads & lifts and stacking etc. complete in all respect [Ref: CAD BIKANER BSR Chapter :07 Item No. 7.4]

8mm thick Cement plaster in cement mortar (1:6) as per design and specification including cost of all materials including mechanical mixing of mortar with all leads & lifts and stacking etc. complete in all respect [Ref: CAD BIKANER BSR Chapter :07 Item No. 7,5]

Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide , (PWD BSR ch B-9 item no. 8)

120cm. high fencing with angle iron posts 50x50x6mm. placed at every 3 Mtr. apart 30cm. in ground embedded in cement concrete 1:3:6 (30x30x45cm) corner & every tenth posts to be strutted with 50x50x6mm angle iron provided with four horizontal lines and two diagonals of black barbed wire between two posts fitted and fixed with G.I. staple including earth work in excavation etc. complete.

Removel of silt /soil/earth, sand, pebbles, malba, debris, rubbish, stone pebbles & obstruction deposited in canal bed up to design line grade and sections having design due to erosion / scour /slipes in canal banks /silting with or without bushes and weeds etc. in dry or moist condition from canal bed including dewatering, loading unloading and disposal at suitable place as directed by engineer in charge with initial lead of 50m. and lift upto 1.5m with proper dressing on canal bed complete in all respect.[IGNP BSR 2023-24 Ch-V, item No-7(c) ] + Add extra over no. 1 to 8 for disposal of excavated material above initial lift of 1.5 and for every additional lift of 1.5 or part there of including loading and -loading wherever required. [IGNP BSR 2023-24 Ch-V, item No-11) ( Complete Rate - 90.00+8.50=98.50)

Supplying, laying, jointing, testing, commissioning, of buried HDPE pipe net work with Hasti / REI / Jain irrigation system or equivalent pipes as per IS -14151(PART-1) including excavation of earth work in all type of soil (except disintegrated rock), depth of trenches should be such that there is a minimum soil cover of 1.0 m over the pipes, refilling and disposal of extra excavated material. The rates are inclusive of all lead and lift of material and also inclusive of all kinds of taxes, levies, turn over tax, service tax, income tax, sales tax, octroi, panchayat tax, royalty and contractor profit, (a) Class 3 working pressure 0.40 Mpa 110 mm dia (IGNP BSR 2023-24 Ch-XIV, item 9.1.3)

Supplying, laying, jointing, testing, commissioning, of buried HDPE pipe net work with Hasti / REI / Jain irrigation system or equivalent pipes as per IS -14151(PART-1) including excavation of earth work in all type of soil (except disintegrated rock), depth of trenches should be such that there is a minimum soil cover of 1.0 m over the pipes, refilling and disposal of extra excavated material. The rates are inclusive of all lead and lift of material and also inclusive of all kinds of taxes, levies, turn over tax, service tax, income tax, sales tax, octroi, panchayat tax, royalty and contractor profit, (a) Class 3 working pressure 0.40 Mpa 125 mm dia (IGNP BSR 2023-24 Ch-XIV, item 9.1.4)

Supplying, laying, jointing, testing, commissioning, of buried HDPE pipe net work with Hasti / REI / Jain irrigation system or equivalent pipes as per IS -14151(PART-1) including excavation of earth work in all type of soil (except disintegrated rock), depth of trenches should be such that there is a minimum soil cover of 1.0 m over the pipes, refilling and disposal of extra excavated material. The rates are inclusive of all lead and lift of material and also inclusive of all kinds of taxes, levies, turn over tax, service tax, income tax, sales tax, octroi, panchayat tax, royalty and contractor profit, (a) Class 3 working pressure 0.40 Mpa 140 mm dia (IGNP BSR 2023-24 Ch-XIV, item 9.1.5)

Supplying, laying, jointing, testing, commissioning, of buried HDPE pipe net work with Hasti / REI / Jain irrigation system or equivalent pipes as per IS -14151(PART-1) including excavation of earth work in all type of soil (except disintegrated rock), depth of trenches should be such that there is a minimum soil cover of 1.0 m over the pipes, refilling and disposal of extra excavated material. The rates are inclusive of all lead and lift of material and also inclusive of all kinds of taxes, levies, turn over tax, service tax, income tax, sales tax, octroi, panchayat tax, royalty and contractor profit, (a) Class 3 working pressure 0.40 Mpa 160 mm dia (IGNP BSR 2023-24 Ch-XIV, item 9.1.6)

Supplying, laying, jointing, testing, commissioning, of buried HDPE pipe net work with Hasti / REI / Jain irrigation system or equivalent pipes as per IS -14151(PART-1) including excavation of earth work in all type of soil (except disintegrated rock), depth of trenches should be such that there is a minimum soil cover of 1.0 m over the pipes, refilling and disposal of extra excavated material. The rates are inclusive of all lead and lift of material and also inclusive of all kinds of taxes, levies, turn over tax, service tax, income tax, sales tax, octroi, panchayat tax, royalty and contractor profit, (a) Class 3 working pressure 0.40 Mpa 180 mm dia (IGNP BSR 2023-24 Ch-XIV, item 9.1.7)

Supplying, laying, jointing, testing, commissioning, of buried HDPE pipe net work with Hasti / REI / Jain irrigation system or equivalent pipes as per IS -14151(PART-1) including excavation of earth work in all type of soil (except disintegrated rock), depth of trenches should be such that there is a minimum soil cover of 1.0 m over the pipes, refilling and disposal of extra excavated material. The rates are inclusive of all lead and lift of material and also inclusive of all kinds of taxes, levies, turn over tax, service tax, income tax, sales tax, octroi, panchayat tax, royalty and contractor profit, (a) Class 3 working pressure 0.40 Mpa 200 mm dia (IGNP BSR 2023-24 Ch-XIV, item 9.1.8)

Construction of Hydrant (Nakka) for sprinkler irrigation system in all type of soil, inner size 0.90 m x0.90 m and depth 1.0 m in brick masonry 230 mm thick of class 100 bricks in cement sand mortar 1:5, 150 mm thick cement concrete 1:3:6 in foundation and 50 mm thick flooring M-15 grade,12 mm thick, inside plaster in cement mortar 1:6 finished with floating neat cement, 120 mm thick coping at top of masonry wall of cement concrete 1:2:4, 2 mm thick M.S sheet openable cover with locking arrangement and zinc coated M.S angle frame 50x50x5 mm.and making arrangement for connection to sprinkler set including sluce valve, butterfly valve and all accessories complete in all respect (IGNP BSR 2023-24 Ch-XIV, item 15)

Designing, supplying, construcion, Installation,Testing & commissioning of Motor driven Horizontal Centrifugal Pumping sets of monoblock type for operation on 3 phase 50 HZ AC supply between 300 to 440 voltage ranges & SAND CAST SS impeller. The set should as per IS 9079-2002 with latest amendments 12.5 H. P (IGNP BSR 2023-24 Ch-XIV, item 14.2)

Designing, supplying, construcion, Installation,Testing & commissioning of Motor driven Horizontal Centrifugal Pumping sets of monoblock type for operation on 3 phase 50 HZ AC supply between 300 to 440 voltage ranges & SAND CAST SS impeller. The set should as per IS 9079-2002 with latest amendments 15 H. P (IGNP BSR 2023-24 Ch-XIV, item 14.3)

Designing, supplying, construcion, Installation,Testing & commissioning of Motor driven Horizontal Centrifugal Pumping sets of monoblock type for operation on 3 phase 50 HZ AC supply between 300 to 440 voltage ranges & SAND CAST SS impeller. The set should as per IS 9079-2002 with latest amendments 20 H. P (IGNP BSR 2023-24 Ch-XIV, item 14.4)

Designing, supplying, construcion, Installation,Testing & commissioning of Motor driven Horizontal Centrifugal Pumping sets of monoblock type for operation on 3 phase 50 HZ AC supply between 300 to 440 voltage ranges & SAND CAST SS impeller. The set should as per IS 9079-2002 with latest amendments 25 H. P (IGNP BSR 2023-24 Ch-XIV, item 14.5)

Providing and fixing suction pipe to pipe inlet and delivery pipe from pump outlet to raising mains of respectine section with M. S. medium class pipe with required pipe and pipe fittings Such as flanges, bends, tees reducer, enlarger, tail pieces, blind flanges, puddel collar dismantling pieces, nut & bolts gaskets, etc including foot valve and suction strainer.125 mm dia (IGNP BSR 2023-24 Ch-XIV, item 16.2)

Providing and fixing suction pipe to pipe inlet and delivery pipe from pump outlet to raising mains of respectine section with M. S. medium class pipe with required pipe and pipe fittings Such as flanges, bends, tees reducer, enlarger, tail pieces, blind flanges, puddel collar dismantling pieces, nut & bolts gaskets, etc including foot valve and suction strainer.150 mm dia (IGNP BSR 2023-24 Ch-XIV, item 16.3)

Supply and fixing of electric control panel of 16 SWG (CRCA) in masonry wall for sitable for 2 nos. electic driven pump sets comprising MCCB, MCB, automatic star delta starter, ampere meter, volt meter, phase preventer, phase indicator, lighting arrangement etc. complete suitable for three phase pump set. All these equipments shall be fixed on 12 mm thick backalite sheet which fixed on M.S. angle frame of size 1800x1200 i.e. made angle iron 50x50x6 mm including making good the surface of wall - 12.5 H. P. (IGNP BSR 2023-24 Ch-XIV, item 17.2)

Supply and fixing of electric control panel of 16 SWG (CRCA) in masonry wall for sitable for 2 nos. electic driven pump sets comprising MCCB, MCB, automatic star delta starter, ampere meter, volt meter, phase preventer, phase indicator, lighting arrangement etc. complete suitable for three phase pump set. All these equipments shall be fixed on 12 mm thick backalite sheet which fixed on M.S. angle frame of size 1800x1200 i.e. made angle iron 50x50x6 mm including making good the surface of wall - 15 H. P. (IGNP BSR 2023-24 Ch-XIV, item 17.3)

Supply and fixing of electric control panel of 16 SWG (CRCA) in masonry wall for sitable for 2 nos. electic driven pump sets comprising MCCB, MCB, automatic star delta starter, ampere meter, volt meter, phase preventer, phase indicator, lighting arrangement etc. complete suitable for three phase pump set. All these equipments shall be fixed on 12 mm thick backalite sheet which fixed on M.S. angle frame of size 1800x1200 i.e. made angle iron 50x50x6 mm including making good the surface of wall - 20 H. P. (IGNP BSR 2023-24 Ch-XIV, item 17.4)

Supply and fixing of electric control panel of 16 SWG (CRCA) in masonry wall for sitable for 2 nos. electic driven pump sets comprising MCCB, MCB, automatic star delta starter, ampere meter, volt meter, phase preventer, phase indicator, lighting arrangement etc. complete suitable for three phase pump set. All these equipments shall be fixed on 12 mm thick backalite sheet which fixed on M.S. angle frame of size 1800x1200 i.e. made angle iron 50x50x6 mm including making good the surface of wall - 25 H. P. (IGNP BSR 2023-24 Ch-XIV, item 17.5)

Providing and laying PVC insulated and PVC sheathed cable of 1.1 KV grade with alluminium conductor of IS:1554 and approved make including testing extra etc. as required of size 16 sq mm 4 core (IGNP BSR 2023-24 Ch-XIV, item 18.2.2)

Providing and laying PVC insulated and PVC sheathed cable of 1.1 KV grade with alluminium conductor of IS:1554 and approved make including testing extra etc. as required of size 10 sq mm 4 core (IGNP BSR 2023-24 Ch-XIV, item 18.1.2)

Geo-refrencing of digitized khasra map and marking chak & sub chak of required size for micro irrigation and providing chak & sub chak wise GCA, CCA details in excel format. Soft copy with two set of Hard copy shall be provided. Rate shall be paid per Ha CCA (IGNP BSR 2023-24 Ch-XIV, item 14.2)