PROVN OF GD ROOM FOR FIVE NCOS/OR NEAR OFFR MESS (BLDG NO P-211), ONE GD ROOM ALONG WITH ELEVATED SENTRY POST AT ARTY BDE CAMP, TOILET BLOCK OF 01X WHB, 01X URINAL POINT WITH TANK AT INF BDE CAMP AND HARD STANDING (100X60) FEET OF B VEH REPAIR FLOO

Amount

Surface excavation n.exc. 30cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Excavation in trenches not exc. 1.5 metre wide and not exc. 1.50 metre in depth for foundation etc and for manholes etc n.exc. 10 Sqm on plan and n.exc. 1.5 metre depth and getting out in soft/loose soil complete all as specified and directed.

Removing excavated materials (soils) to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.50 above the starting point complete all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick as in soft/loose soil complete all as specified and directed.

Material and labour for preconstructioin anti termite treatment by treating the top surface of filled earth at the rate of 7.50 litres of emulsion per square metre of surface complete all as specified and directed.

Material and labour for preconstructioin anti termite treatment by treating the bottom and sides of excavation at the rate of 5 litrs of emulsion per square metre of surface area complete all as specified and directed.

Material and labour for preconstructioin anti termite treatment by treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the substructure in contact with backfill to be measured) complete all as specified and directed.

Material and labour for preconstructioin anti termite treatment by treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Material & labour for approved soil filling under the floor, spreading and levelling in layers n.exc. 25cm thick, well ramming including watering as required complete all as specified and directed. Note: Soil obtained from earth work shall be used.

Material & labour for hardcore of broken bricks gauges n.exc. 63mm, deposited spread and leveled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and directed.

Material & labour for cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete and sub base of floor complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surface of concrete complete all as specified and directed.

Use and waste of form work of sides of pillars, posts, struts, piers, columns etc square or rectangular or polygonal rough finished flat surfaces of concrete complete all as specified and directed.

Material and labour for form work to sides and soffits of beams lintels etc rough finished flat surfaces of concrete complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick flat fair finished surfaces of concrete complete all as specified and directed.

Material and labour for form work to the edge of concrete flat n.exc 200 mm thick , rough finished surfaces of concrete complete all as specified and directed.

Supply & fix mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Supply & fix mild steel TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required as in stirrups binding with mild steel wire (anealed) but less than 0.9 mm dia complete all as specified and directed.

Matereial and labour RCC M 25 (Design Mix) type B1 using 20 mm graded stone aggregate as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

Matereial and labour RCC M 25 (Design Mix) type B1 using 20 mm graded stone aggregate as in columns, pillars etc complete all as specified and directed.

Matereial and labour RCC M 25 (Design Mix) type B1 using 20 mm graded stone aggregate as in beams, lintels over 1.5 m span etc complete all as specified and directed.

Matereial and labour for RCC M 25 (Design Mix) type A-1 using 20 mm graded stone aggregate for roof slabs supported on walls, beams and the like complete all as specified and directed.

Material & labour brick work with fly ash bricks in CM 1;6 straight or curved on plan exeeding 6m mean radius complete all as specified.

Material & labour brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM (1:4) complete all as specified and directed.

Supply only integral water proofing compound complete all as specified & directed.

Material & labour for 15 mm thick rendering in CM 1:6 on fair faces of brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material & labour for 15 mm thick rendering on other than fair faces of brick work or concrete surfaces,in CM(1:4) surface finished even and smooth without using extra cement complete all as specified and directed.

Material & labour for 5 mm thick plaster in CM 1:3 on ceiling surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for 75 mm thick cement concrete 1:3:6 type C-2 using (40 mm graded stone agg) as in sub base complete all as specified and directed.

Matereial and labour Machine cut kota stone slab flooring 18-20mm thick over incl 15mm thick cement screed base laid in cm 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Matereial and labour Machine cut kota stone slab flooring 18-20mm thick over incl 20mm thick rendering laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Matereial and labour Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, (600x600) in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed complete all as specified and directed

Matereial and labour Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.6 sqm but not exceeding 0.11 sqm, in vertical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

Material and labour for coloured Non Skid ceramic tiles 7 to 8 mm thick, (square / rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and and directed

Material & labour for glazed coloured ceramic tiles of size 450x300x7-8mm thick, on vertical surfaces set and jointed in neat cement slurry and pointed in white/ coloured cement to match with existing work over and including 10mm thick rendering in CM 1:4 complete all as specified & directed.

Matereial and labour 75mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in path /plinth protection , finish even & smooth without using extra cement all as specified and directed.

Material & labour for preparation of new plastered surfaces of walls etc and applying two coats of cement base paint over a coat of primer complete all as specified & directed. Make: Super Snowcem /Duracem/Accrocem or equivalent make as specified in PS.

Material & labour for preparation of new plastered surfaces of walls with Birla /JK wall care putty and applying two coats of Oil bound distemper to match the existing surfaces as required, complete all as specified & directed.

Material and labour for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified & directed.

Matereial and labour for padding in PCC 1:2:4 type B0 (using 12.5mm graded stone agg) laid to a minimum consolidated thickness 50mm to provide a finished slope 1:30 complete all as specified & directed.

Material & labour for cleaning of plastered /concrete surfaces and applying priming coat using bituminous primer @ 0.30 Kg/Sqm. followed by evenly a tack coat @ 1.20 Kg/Sqm. using with 85/25 grade bitumen, over laid with 3mm thick APP modified polymeric water proofing membrane with non woven polyester reinforced of weight not less than 3.6 Kg/Sqm. unrolled and bonded to substance with side and end laps 75mm and 100mm as per manufacturer’s instructions and finished top of APP water proofing polymeric membrane with a coat of hot blown industrial bitumen 85/25 grade @ 1.20 Kg/Sqm and finally finished with a coat of bituminous aluminium paint @ 0.20 Kg/Sqm complete all as specified and directed.

Supply and fix 30 mm thick flush shutter solid core construction with particle board and plywood face panels commercial type on both side complete all as specified and directed.

Matereial and labour gauzed shutter shall be made out of mild steel U frame 35x35x5mm, 25x25x5mm and 1.5mm thick as shown on drawing. The frame for shutter shall be of pressed steel and 10mm Square bars grill complete with fly proof wire mesh having 0.63mm nominal dia wire and 1.4mm average with aperture and 250mm M S sliding bolt , 150mm MS tower bolts and Aluminium 200mm Handle including two coats of synthetic enamel paint over a coat of red oxide all specified and directed by Engr-in -charge.

Supply & fixing pressed steel frames for doors with one or more rebates including necessary fixing lugs lugs, hinges, lock strike plates etc completed size of frame 125x60mm made out of 1.25mm MS sheets complete all as specified & directed.

Supply and fix flat iron hold fast welded to angle iron door frame complete all as specified and directed.

Mild steel U frame door frame 40mmx40mmx6mm conforming to Fe 410-0 incl 12mm dia deformed bars for strengthing at bottom of chowkhats incl cutting floor at bottom to accommodated strengthing bars & making good the floor in PCC 1:2:4 type B-0 to match the existing floor complete all as specified and directed.

Supply and fix solid PVC door frame plain colour of size 50mm x 47mm made out of 5mm PVC sheet reinforced with MS square fixed with rawl plug tube as per specification and drawing complete all as specified and directed.

Supply & fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC , ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for to rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed to getter with solvent cement, supplying & fixing in the frame at site as per specification & drawing for Item No. 08080 on page No 156 of SSR 2010 (Part-II).

Supply & fix 125mm size aluminium alloy handles cast type anodized complete all as specified & directed.

Supply and fix aluminium tower bolts 150mm long, of extruded section complete all as specified and directed.

Supply and fix 250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

Supply and fix MS helical door spring 150 mm size complete all as specified and directed.

Matereial and labour preparation of new or previously untreated wooden surfaces of any description, not other wise described over 10cm width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Matereial and labour preparation of new or previously untreated steel surface of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply and fixing PVC waste pipes of 40/32mm bore suitable for wash hand basins/sinks complete all as specified & directed.

Supply & fixing steel C.P. grating 100/125 mm dia as reqd at site complete all as specified and directed .

Supply and fix for 110 mm bore PVC floor traps plain with grating and 300 mm long out let including jointing with cement concrete type B -1 1:2:4 complete all as specified & directed.

Supply and fix PVC bends 110mm bore, any radius complete all as specified & directed.

Matereial and labour Steel window box type using ERW 'P' section comprising double frame for gauged and glazed skeleton shutter jointed internally with flat iron 40x3mm complete including hinges, handle tower bolts stops, lugs etc all as shown on drawing Note (i) For the purpose of measurement & payment double shutter with frame shall be considered as one unit (ii) Unit rate quoted against this item shall also include the iron mangeryas shown on drgs (iii) Guard bars glazing & wire mesh shall be measured & paid for separately.

Supply & fix factory made steel windows or ventilators fixed type, complete all as specified & directed.

Supply & fix mild steel framed work such as grills, gratings guard bar etc with ends of bars shouldered and/ or riveted etc completed all as specified.

Supply and fix 20mm Gun -metal,globe or gate valves,with iron wheel head ,screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply & fix bib taps cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe of 15mm bore, complete all as specified & directed.

Supply & fix in vitreous china wash hand basin, white, flat back of size 550x400mm (excluding taps, waste chain and plug and porcelain stopper) but including brackets suitable for 15mm dia pipe complete all as specified & directed.

Supply & fix angular valve, 15 mm dia, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down, high pressure screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified & directed.

Supply & fix rotational moulded polyethylene water storage tanks 500 liters capacity, (cylindrical, vertical in closed top) hoisted and fixed in position with all fittings all as specified including dismantling existing water tanks complete all as specified & directed.

Supply & fix in PVC low level flushing cistern of 9-10 ltrs capacity, ISI Marked, white, symphonic action type with inlet, ball valve, float and handle including brackets and PVC flush pipe of 32 mm bore, suitable for low level cistern complete all as specified & directed.

Supply, fix 15mm bore, GI tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

Supply, fix 20 mm bore, GI tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

Supply & fix 3mm thick sheet glass, ordinary quality, and glazing with oil putty/beading in square not exceeding 0.50sqm each pane complete all as specified & directed.

Supply & fix 3mm thick sheet glass, pin headed, and glazing with oil putty/beading in square not exceeding 0.50sqm each pane complete all as specified & directed.

Supply & fix galvanized mild steel wire cloth with 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanized wire staples complete all as specified & directed.

Supply & fix aluminium alloy wire cloth with 0.5 mm nominal dia of 45wire and average width of aperture 1.14 mm and fixed aluminium wire staples complete all as specified & directed.

Supply & fix butt hinges, 100 mm long of stainless steel, complete all as specified & directed.

Supply & fix in PVC connections of 450mm long of PRYAG Make suitable for 15mm dia iron pipe including PTMT nuts complete all as specified & directed.

Supply & fix PVC ball valves, high pressure with polyethylene float and fly nut complete screwed for iron pipe 20mm bore complete all as specified & directed.

Supply & fix vitreous china squatting pan of ‘Orrisa pattern’ size 580x440mm, white with, integral foot rest including replacement of ‘P’ or ‘S’ trap, lime concrete bedding and making good floor complete all as specified and directed.

Supply & fix in vitreous china urinal half stall type with including providing & fixing of plugs bedding against wall in cement mortar 1:2 pointing around urinal back in cement mortar complete all as specified and directed.

Supply & fix pillar taps, fancy type cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore, complete all as specified & directed.

Supply and fix waste coupling of PTMT (half or full threaded) suitable for urinals (Minimum weight 32mm-45gms) complete all as specified and directed.

Supply and fix PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints laid in trenches in floors or fixed to wall includng clemmps wiith bults and nuts complete all as specified and directed.

Supply and fix PVC (SWR) pipes 75 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

Supply and fix PVC bends 75mm bore, any radius complete all as specified & directed.

Supply and fix PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. Make: Kisan/Prince or equivalent make as specified in PS.

Supply and fix PVC (SWR), junction single, (Single T) equal or unequal 110 mm bore complete all as specified and directed.

Supply and fix Tubular towel rail 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

Material & labour for plain cement concrete bed to drain pipes including packing under, haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) for 150 mm bore pipe complete all as specified and directed.

Matereial and labour Slat-glazed stoneware drain pipes 150 mm dia laid in trenches in floors or fixed to wall including stock clemps with bolts & nuts and jointed complete all as specified and directed.

Matereial and labour Rendring 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 complete all as specified and directed.

Matereial and labour for PCC(1:3:6) type C1 (using 20mm graaded crushed stone aggregate) as in benching to man hole complete all as specified and directed.

Material & labour for construction of Septic tank 25 users capacity, exc in ordinary soil, foundation conc in PCC 1:2:4, brick work in CM 1:4 , RCC slab and covers in RCC M-25 design Mix 1:2:4 including RCC precast manhole cover having 6 mm plate embedded all around /fibre reinforced cover with angle iron frame , CI Vent pipe complete all as shown in TD Drg ( TD/217 sheet 1/7 to 7/7 of HQ CEBZ ) complete all as specified and directed.

All as per item No 92.00 above but for 50 users complete all as specified and directed.

Matereial and labour 60mm thick PCC interlocking paver block confiming to IS15658-2006, M-35 grade with grey cement and pigment (interlocking type) laid over and including 25 mm thick sand cushioning, ineterlocking tiles jointd filled with sand and campacted with mechanical plate vibrator complete all as specified and directed.

Matereial and labour 80mm thick PCC interlocking paver block confiming to IS15658-2006, M-35 grade with grey cement and pigment (interlocking type) laid over and including 25 mm thick sand cushioning, ineterlocking tiles jointd filled with sand and campacted with mechanical plate vibrator complete all as specified and directed.

Material and labour for 60 mm thick coloured rubber moulded (comparising of red & yelow colour in 50:50 ratio) machine pressed interlocking pavers block in approved shape and size confirming to IS 15658-2006, M-35 Grade set and laid over and including 25mm thick coarse sand complete all as specified and directed.

Material and labour for precast cement concrete solid block masonry 1:2:4 type B-1 using 20 mm graded crushed stone aggregate exc 10 cm in width and set in CM 1:6 complete all as specified and directed

Supply and fix vitreous china wash down water closet pan (Padestal Pattern) white, with 'P' of 'S' trap including connection to trap and cistern and flush pipe excluding flushing cistern) including PVC white seat cover, closed pattern fixed with aluminium hinging device and making good to disturbed surface of floor complete all as specified and directed .

Supply and fix brass CP bottle traps 32mm bore for wash basins with inlet & outlet screwed for pipe or connections including necessay packing, union & cap complete all as specified and directed.

Supply and fix fancy type glass corner shelf made of not less than 5.5mm thick toughned glass of size 250mm x 250mm fixed with CP railling complete all as specified and directed

Supply and fix fancy type CP brass soap dish complete all as specified and directed Make : Sikko/Prayag or equivalent make as specified in PS.

Supply and fix 15mm bore fancy type CP brass concealed stope cock complete all as specified and directed.

Supply and fix bib taps two way 15mm bore, cast copper alloy choromium plated with crutch or butter fly handle screwed down screwed for iron pipe or brass ferrul complete all as specified and directed.

Supply and fix 100 mm long aluminium anodised barrel tower bolts of extruded section.all as specified & directed

Supply and fix 110mm dia PVC (SWR) vent cowl complete all as specified and directed.

Cutting into existing manholes for connecting new drains/pipe, making good to pipe and rendering, cutting out existing benches for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished, and reforming benching as required for 150mm internal dia for pipe all as specified and directed.

Material & labour for construction of Soakage wells, excavated. in ordinary soil, foundation PCC 1:3:6 walls of honey combed and solid brick in cement mortar, RCC slab in M25 design mix, filling work with brick bats, complete of size 1.80 m dia x 3.00m effective depth complete all as shown in TD Drg ( TD/309 sheet 1/4 to 4/4 of HQ CEBZ ) complete all as specified and directed.

Material and labour for cement conc 1:3:6 type C-2 (using 40mm graded crushed stone aggregate ) as in foundation manholes complete all as specified and directed.

Material and labour for cement conc 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in coping to manholes complete all as specified and directed.

Material and labour for precast cement conc 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in manhole covers slabs set in cement mortar 1:4 complete all as specified and directed.

Material and labour for sub main wiring with 2x4.00 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor FRLS cable with and including continuous earth wire of size 4.00 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dolly including all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as specified & directed. Note : One meter of conduit along with 2x4.00 sqmm wire and one 4.00 sqmm earth shall be measured as one unit length )

Material and labour for point wiring with 1.5 Sqmm nominal cross sectional area, single core, 1100 Volts grade, stranded, FRLS PVC insulated, unsheathed, copper conductor cable in and including PVC concealed conduit of any size/dia complete with all accessories/fittings, brass screws, washer etc, sunk zinc coated pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded copper conductor cable, unsheathed and connected to common earth and earth dolly for One tube light/Bulb/Bell/ street light point controlled by one, one way switch 05/06 Amps complete all as specified and directed.

All as per serial item No 112.00 above but for one ceilling fan/exhaust point controlled by one, one way switch 05 / 06 Amps.

All as per serial item No 112.00 above but for One 3 pin, 05 / 06 Amps socket outlet point on independent board controlled by one, one way 05 / 06 Amps switch.

All as per serial item No 112.00 above but for One 3 pin, 05 / 06 Amps socket outlet point on same board controlled by one, one way 05 / 06 Amps switch.

All as per serial item No 112.00 above but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15/16 Amps socket outlet point on independent board.

Supply and fix switch piano flush type, 05/06 Amp single pole, one way 240 volts complete all as specified and directed.

Supply and fix socket outlet 3 pin 05/06 Amps and 15/16 Amps (2 in 1 Multipurpose) flush type 240 volts complete all as specified and directed .

Supply and fix socket outlet 5 pin 05/06 Amps 240 volts complete all as specified and directed .

Supply & fixing switch piano, flush type, 15 / 16 Amps, single pole, one way, 240 volts complete all as specified & directed.

Supply and fix lamp holder (Angular/Straight), insulated body, with back plate for batten fitting all as specified and directed by Engineer-in-Charge.

Supply and fixing LED lamp 9/10Watts, retrofit type all as specified and directed Make- Crompton/Havells /Phillips/Surya or equivalent make as specified in PS.

Supply & fixing of ceiling rose 3 terminal PVC / poly carbonate, isolated body complete all as specified & directed.

Supply and fixing ceilling fan 1200 mm sweep sisngle phase 50 Hz BEE 5 star ratinng completet with accessoreis, including making connections from fan box to fan with three core flexible copper wire of size 23/0.000076 all as specified and directed. Make : Crompton/Khetan/Havells or equivalent make as specified in PS.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 12 way, with 200 Amp rated copper bus bar and IP-43 protection with metal double door and flush to wall including all cutting etc on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as directed by Engineer-in-Charge.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 Volts, 4 way, with 200 Amps rated copper bus bar and IP-43 & IK 09 protection including provision for four pole isolator/MCB as incomer with meatl double door and flush to wall including all cutting and chases complete all as specified and directed. Make: ABB/Havells/Legrand/Schneider or equivalent make as specified in PS.

Supply and fixing MCB, SP, AC, 240 volts "B" series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed. Make : ABB/Havells/Legrand/Schneider or equivalent make as specified in PS.

Supply & fixing MCB, DP (Double Pole), AC, 240 volts, B series capacity 32 Amps to 40 Amps 10kA and making connections complete all as specified & directed Make: Legrand/ABB/Sschneider or equivalent make as specified in PS.

Supplying, laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 16 Sqmm 2 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches, fixing on wall, under road crossing through protection pipe etc complete all as specified and directed.

Supplying, laying commissioning, testing of XLPE under ground LT cable 1100 volts grade of size 10 Sqmm 2 core armoured, PVC sheathed with aluminium conductor heavy duty laid in trenches, fixing on wall, under road crossing through protection pipe etc complete all as specified and directed.

Supply/laying and fixing 40 mm bore galvanised steel tubes with all fittings, light grade, laid in trenches for cable protection complete all as specified and directed.

Material and labour for washed river dry sand cushioning in trenches 80mm thick before laying the cable and 150mm thick after laying the cable including spreading levelling and hard punning complete all as specified and directed.

Material and labour for contineous brick edging with width equal to the length of the brick of whole sub class 'B' bricks laid on flat for protection of cable complete all as specified and directed.

Supply and fix decorative LED tube light fitting 1x20 Watt, with opal diffuser, environment friendly, energy efficient MS batten with retrofit T8 polycarbonate tube-01 No, complete with all accessories and fixing material complete all as specified and directed.

Supply and fixing steped type electronic fan regulator flush type on the existing sheet etc. AC, 230 volts with and including connector complete all as specified & directed by Engineer-in-Charge

Material & labour for earthing complete with galvanised mild steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed. (Note- After completion of work if desired result of earthing is not obtained the earthing shall be redone without any extra cost to Govt.)

Supply and installed LED security light fitting 1x45 Watt luminaries with die cast aluminium housing comprising epoxy powder coated enclosed with PC cover in frame with high power LED white lampt type of capacity 45 Watt security light brackets of 32 mm dia GI pipe medium grade upto 0.8mtr long bend to shape at 100-120 degree including flat iron clamps and suitable nuts and bolts grouted n wall including al lmeterial required for fitting complete all as specified and directed Make- Phillips/Havells/Surya or equivalent make as specified in PS.

Supply and fix desert cooler electric driven single phase 230 Volt metalic body (GI) medium, capacity of water not less than 67 ltr, 1350 RPM and power consumption not more than 240 watt, 50 Hz complete all as specified and directed make Ram Cooler Model No -Eco or equivalent make in Khaintan/Usha/Crompton.

Supply and fix decorative LED batten 20 Watt aluminium housing integrated type complete with all accessories and fixing material all as specified and directed Make Havells /Crompton/Wipro/Suraya or equivalent make as specified in PS.

Supply and fixing LED tube light fitting 9/10 watt surface mounted, with extruded polycarbonate, integrated lamp & driver, with opal diffuser and decorative end plates complete with acessories all as specified and directed Make : Havells/Crompton/Surya or equivalent make as specified in PS.

Supply and installed LED security light fitting 1x30 Watt luminaries with pressure die cast aluminium housing comprising high power with PC cover with LED driver, IP-66 protection and IK-07 impact resistance complete all as specified and directed Make Havells/Crompton/Bajaj/Phillips or equivalent make as specified in PS.

Supply and fixing LED bulk head light fitting wall mounted with back lit LED lamp 10 Watt, complete with all acessoires all as specified and directed.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amp rated copper bus bar and IP-43 protection with metal double door and flush to wall including all cutting etc on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as directed by Engineer-in-Charge.

Supply and fixing of ceiling fan BEE star rated power consumption not more than 50 watts, white colour, 1200 mm sweep, copper winding, single phase, 220 volts, 50 Hz, with blade set of 3, with down rod as per site requirement including connection three core flexible copper wire 1.5 Sqmm multistranded from ceiling rose to fan connector, wtih and including fan hook duly grouted on roof complete all as specified and directed. by Engr-In-Charge. Make:Havells model NO ES 50 or equivalent in crompton/orient/Usha/Bajaj or equivalent make as specified in PS.

P K ASSOCIATES

Rajneesh Jain

AR Enterprises