REPAIR/ PAINTING AND POLISHING OF VARIOUS TYPES OF STEEL FURNITURE, WOODEN FURNITURE AND REPAIR/ RETIGHTENING OF CHARPOY GI PIPE NYLON NEWAR AND CONVERSION INTO CHARPOY GI PIPE PLYTOP AND MISC ARTICLES AT GRC AND APS UNDER GE KAMPTEE

Amount

GI PIPE PLY TOP INTO GI PIPE PLY TOP :-

Removing of old unserviceable plytop from GI charpoy and supply & fixing two Nos stiffners made out of MS square pipe size 25mm x 25mm x 1.5mm conforming to IS-2062 of 1999 Grade 'A' (weight of pipe not less than 1.06 kg/mtr). The stiffners shall be welded to the frame of the GI charpoy at equal distance joining the long rail such that they lie parallel to short rails and perpendicular to the long rail. The stiffners shall be painted with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. Make : Prakash/ Surya

Removing of old unserviceable long rails having both threaded broken end and supply & fixing new long rail made out of GI tubing 32mm bore mediam grade ISI marked including making threaded both ends and fixing as shown on drawing complete all as specified and directed. Make of pipe:-SURYA/ TATA/ JINDAL

Removing of old unserviceable short rails of GI charpoy having both threaded broken ends and S&F new short rails of GI charpoy obtained from item No above, including making threads at the both ends and fixing as shown on drawing complete all as specified and directed.

Removing of old unserviceable leg and supply & fixing new leg made out of short rail of GI charpoy obtanied from Srl item No. 1(d) above, including welding of MS plate at the bottom of leg and making thread other end & fixing in position complete all as specified and shown on drawing.

Removing of old unserviceable GI elbow three way and supply & fixing of new GI elbow three way size 32mm bore with new ISI mark (weight not less than 420 gms each and re-assembling of GI Charpoy after replacement of broken elbow complete all as specified and directed.

Removing old unserviceable check nuts from long rail of GI charpoy and supply & fixing of new check nut of 32mm bore and 10mm wall thick, (Wt not less than gms each) ISI marked and fixing in the same in position complete all as specified and directed.

S&F new 12mm thick plywood ISI marked BWR Grade of approximate size 1980mm x 1050mm conforming to IS-303/1989 on top of GI pipe charpoy fixing with 10 Nos new nut, bolt and washer of suitable size after re-tightining of all joints of charpoy complete all as specified and directed. Make: Kitply /Archid/ Greenply/ National Note:- Each corner of plywood should be round shaped.

Chair Revolving

Removing old unserviceable Seat of computer chair and supply & fixing New seat of computer chair all as per drawing. Seat shall be made of 50 mm thick synthetic foam of 32 density fixed over 12 mm thick plywood commercial and shall be stitched with superior quality fabric cloth of approved shade complete all as specified and directed.

Removing old unserviceable back of computer chair and supply & fixing new back of computer chair all as per drawing . Back shall be 25 mm thick respectively synthetic foam of 32 density fixed over 12mm thick plywood commercial and shall be stitched with superior quality fabric cloth of approved shade complete all as specified and directed.

Removing old unserviceable cover cloth of (seat and back) from existing computer chairs. S&F of new fabric cloth duly approved by GE, shall be used for seat and back of existing chair computer complete all as specified and directed.

Removing old unserviceable Arms rest of computer chair and supply & fixing new arms rest of computer chair all as per drawing complete all as specified and directed. Note: Arm Rest shall be polyurethene "D" shape.

Removing old unserviceable Revolving wheels of computer chair and supply & fixing New Revolving Wheel of computer chair all as per drawing complete all as specified and directed.

Removing old unserviceable padestal Assembly and S&F New Steel Padestal Assembly of computer Chair all as per drawing complete all as specified and directed.

Removing old unserviceable Hydroclic System gas lift (Air soft) and supply & fixing of New Hydrolic System (Air Soft) of computer chair all as per drawing complete all as specified and directed.

LOCKER BED SIDE STEEL:-

Removing of old unserviceable hasp and staple and supply & fixing of new CP Hasp and Staple 75mm long as per given in drawing and site requirement complete all as specified and directed.

Removing of old unserviceable stainless steel handle and supply & fixing of new stainless steel handle 100mm long with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed.

Removing of old unserviceable MS shelf made to shape out of 1mm thick MS sheet and supply & fixing of new MS shelf made to shape out of 1mm thick MS sheet fxing bolts or welding as per given in drawing and site requirement complete all as specified and directed.

Removing of old unserviceable leg of size 600mm x 80mm x 100mm and supply & fixing of new leg of size 600mm x 80mm x 100mm made out of 1mm thick MS sheet fixing bolts or welding as per given in drawing and site requirement complete all as specified and directed.

Removing of old unserviceable MS shutter made to shape and supply & fixing of new MS shutter made out 1mm thick to shape as per given in drawing and site requirement complete all as specified and directed.

Table 900x600 With Drawers:

Removing of old unserviceable long rails of Table 900mm x 600mm without drawer and S&F new Long rail made out 1st class teak wood complete all as specified and directed.

Removing of old unserviceable shortrails of Table 900mm x 600mm without drawer and S&F new short rail made out 1st class teak wood complete all as specified and directed.

Removing of old unserviceable legs of Table 900mm x 600mm without drawer and S& F new legs made out 1st class teak wood complete all as specified and directed.

Re-tighting the Joints of Frame of table 900mm x 600mm without drawer duly provied new bamboo Pins as per requirement and making tight all loose components complete all as specified and directed.

Removing of old unserviceable box including drawers of table 900mm x 600mm and supplying and fixing new drawers, shall be of 18mm thick prelaminted particle board except back side eand back shall be made of 6mm thick commercial plywood complete all as specified & directed and as shown in drg.

Removing of old unserviceable top of Table 900mmx600mm without drawer and S& F new Top made out Prelaminated particle board exterior grade 18mm thick 4mm thick teak wood beading around of 'Top' duly french polished complete all as specified and directed.

Chair School with Hand Rest

Removing of unserviceable PVC seat of chair school with hand rest and supply and fixing in replacement of one peace PVC seat & back (made of blow plast or fabric ) of chair school wih hand rest all as per drg and as directed.

Removing unserviceable Writing /hand borad of chair school and S&F and fixing in replacement new Writing/hand board (made of 18mm thick Exterior grade Prelaminated Partical Board both side Teak Finish with 1 mm thick PVC beading allround) alongwith iron supporting arrangements of chair school with hand rest all as per drawing complete all as specified and directed.

Removing unserviceable Hard rubber shoes of chair school with hand board and supply and fixing in replacement of hard rubber shoes of chair school with hand board all as per drg complete all as specified and directed.

M&L for painting of frame of chair school with hand board with two coats of synthetic enamel white paints including welding where required and preparation of surfaces complete all as specified and directed.

M&L for re-painting of mentioned below steel furnituire as per the following steps:- (a) Denting of bent surfaces with the help of hammer in best workmanship manner. (b) Removing old paint by scrubbing with sand paper 150 No thoroughly. (c) Applying one coat of metal primer. (Make: Asian/ Nerolac/ Dulux). (d) Applying metal putty to even surface.wait period 2-3 hours to be given for putty to set and dry completely. scrub off the excess putty with 150 No and paper and spraying little amount of water simultaneously. (e) Wipe the surface with solt dry cloth and apply one coat of enamel paint of light shade as approved by GE.

Almirah large steel with shelves.

Almirah med steel with shelves.

Locker bed side steel.

Table office clerk steel.

Almirah large steel with glazed door.

ALMIRAH LARGE STEEL WITH SHELVES:-

Removing of old unserviceable MS clamps and supply & fixing of new MS clamps with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed.

Removing of old unserviceable lock 6 lever and supply & fixing of new lock 6 lever with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed. Make: Link /Godrej/ Standard/ Aligarh

Removing of old unserviceable stainless steel handle and supply & fixing of new stainless steel handle 100mm long with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed.

Removing of old unserviceable 3 way Locking device with MS rods and cover box and supply & fixing of new 3 way Locking device with MS rods and cover boxs with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed.

Removing of old unserviceable MS shelf made to shape out of 1mm thick MS sheet and supply & fixing of new MS shelf made to shape out of 1mm thick MS sheet fxing bolts or welding as per given in drawing and site requirement complete all as specified and directed.

Removing of old unserviceable Base channel of size 485x80x100mm and supply & fixing of new Base channel of size 485x80x100mm to be welded at 50mm from each end of length as per given in drawing and site requirement complete all as specified and directed.

Removing of old unserviceable MS shutter made to shape and supply & fixing of new MS shutter made to shape as per given in drawing and site requirement complete all as specified and directed.

Removing of old unserviceable MS Butt hinges 75mm and supply & fixing of new MS Butt hinges 75mm with nut bolts or welding as per given in drawing and site requirement complete all as specified and directed.

CHAIR DINING

Removing of old unserviceable rear leg of chair dining and supply and fixing with new legs of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg.

Removing of old unserviceable front leg of chair dining and supply and fixing with new legs of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg.

Removing of old unserviceable front rail/side rail/ back rail of chair dining and supply and fixing with new front rail/side rail/ back rail of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg.

Removing of unserviceable bottom stiffener of chair dining and supplying and fixing with new bottom stiffener of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg.

Removing of unserviceable back rest of chair dining and supplying and fixing with new back rest of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg.

Removing of unserviceable cane stiffener of chair dining and supplying and fixing with new cane stiffener of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg.

Removing of old cane from chair dining (bottom) and re-canning with new best quality plastic cane 2mm wide white colour cane in godrej pattern complete all as specified & directed. Make : Shah/ Maharashtra/ Arihant.

M&L for preparation of old/new chair dining and polishing of high gloss french polish of chair dining complete all as specified & directed.

M&L for preparing of old/new polished wood based furniture articles as per the following steps:- Step 1 Sanding:- The wood components shall be rubbed with sand paper No 120 along the grains to remove any dust/ wax/unwanted stains from the surface, the sanding will be repeated with sand paper between 180-220 grit in order to achieve the smooth surface and the wood will be wiped clean with soft clean cloth complete all as specified and directed. Steps 2 : Staining : Any cracks or holes shall be filled with wood filler of good quality. After the wood filler has dried completly sanding with a stain of approved shade will be then applied to the prepared surface with the help of a soft malmal cloth or brush along the grain'. two to three coats of staining will be done letting the stain dry completly between each coats and sanding every time very fine grit sand paper (220-320). Note: Excess stain should be wiped off before drying and getting absorbed in wood. Step 3 Polishing : Wood will be finished with a good quality french polish (mixture of shellac grains and methylated spirit in ratio 1:10) two to three coats shall be applied to prepared wood surface letting each coat to dry and absorbed fine sanding can be done if required, Polish shall be applied with a soft cloth/ brush along the grains and not against it to achieve high gloss complete all as specified and directed.

Table dining 04/06 person.

Table dining 8 person.

Teapoy.

Table writing.

Table 3'x2' with drawer

Table 3'x2' without drawer

Table dressing ladies with mirror

Table dressing gents with mirror

Stool dressing

Peg Table

Chair writing

Chair easy

Chair dining

Table bed side

Table center

Hat stand with mirror

CHAIR WRITING

Removing of old unserviceable rear leg of chair writing and supply and fixing with new legs of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg.

Removing of old unserviceable arm rest of chair writing and supply and fixing with new arm rest of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg.

Removing of old unserviceable front leg of chair writing and supply and fixing with new legs of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg.

Removing of old unserviceable front rail/side rail/ back rail of chair writing and supply and fixing with new front rail/side rail/ back rail of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg.

Removing of unserviceable stiffener (side and central one) of chair writing and S&F new stiffener (side and central one) of first class hard teak wood, made to shape complete all as specified & directed and as shown in drg.

Removing of old cane from chair writing (bottom) and re-canning with new best quality plastic cane 2mm wide white colour cane in godrej pattern complete all as specified & directed. Make: Shah/ Maharashtra/ Arihant.

M&L for preparation of old/new chair writing and polishing of high gloss french polish of chair writing complete all as specified & directed.

NOTE:- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs.54,483.00]

NIHAL ENTERPRISES

M/S Shanti Enterprises

M/s Raghav Traders

Bidder Name

M/S Shanti Enterprises

M/s Raghav Traders

NIHAL ENTERPRISES

H.M Traders