Loading…
Loading…
Tender Value
₹2.7 Cr
EMD Value
₹5.4 L
Closing Date
10 Jun 2026, 11:00 amClosed
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
MALDA DIV
14 conditions · 3 needing a document upload
(1) As per item no 10.0 of GCC 2022 and Advance Correction Slip No.1 to 11 of Indian Railways Standard General Conditions of Contract, April' 2022 (Copy attached in download section) - Supporting Document Mandatory. (2) Submit requisite information as per Annexure-VIB, along with copy of Audited Balance Sheets - duly certified by CA / Certificate from CA duly supported by Audited Balance sheet is mandatorily.
(1) As per item no 10.0 of GCC 2022 available in Document section and Advance Correction Slip No.1 to 11 of Indian Railways Standard General Conditions of Contract, April' 2022 (Copy attached in download section) is applicable. Document mandatory. (2) Annexure-V and V(A) of GCC 2022 is mandatory.
Definition Of Similar Work :-Panel, Interlocking OR Route Relay Interlocking or Electronic Interlocking OR IBH OR Automatic Signaling OR LC gate interlocking or AFTC or SSDAC or MSDAC or HASSDAC or BPAC
54 conditions · 10 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Scanned copy -in PDF format- of the details regarding the Association of Railway Officers with the tenderer -for details please refer ANNEXURE-U-V of Coml Compliance.
Scanned copy -in PDF format- of the details of the works the tenderer presently in hand during the last three years -for details please refer ANNEXURE-IV Coml Compliance.
Scanned copy -in PDF format- of the details of the List of the Arbitration cases of the tenderer during last 5 years -for details please refer ANNEXURE-U-VI of Coml Compliance.
Scanned copy -in PDF format- of the details of the List of the Court cases of the tenderer during last 5 years -for details please refer ANNEXURE-U-VII of Coml Compliance.
Scanned copy of the NEFT in PDF format as per Annexure - U-VIII of of Coml Compliance.
In case (i) the office is closed due to any reason or (ii) any one of opening official is on leave or out from Head Quarter, on the stipulated date & time of opening of the tender, whatsoever the tender will be Opened on the next working day on which both opening officials are present at Head Quarter.
The Railway reserves the right to verify all statements, information and documents submitted by the bidder in his tender offer, and the bidder shall, when so required by the Railway, make available all such information, evidence and documents as may be necessary for such verification. Any such verification or lack of such verification,by the railway shall not relieve the bidder of its obligations or liabilities hereunder nor will it affect any rights of the railway thereunder.
In case of any wrong information submitted by tenderer, the contract shall be terminated, Earnest Money Deposit (EMD), Performance Guarantee (PG) and Security Deposit (SD) of contract forfeited and agency barred for doing business on entire Indian Railways for 5 (five) years.
Each page of the copy of documents/certificates in support of credentials, submitted by the tenderer, shall be self-attested/digitally signed by the tenderer or authorized representative of the tendering firm. Self-attestation shall include signature, stamp and date (on each page).
Nimtita - Provision of 2nd detection at NIMTITA (NILE) for reliability improvement.
MLDT_SNT_26-27_04_OT
MLDT_SNT_26-27_04_OT
Open
Works - General
365 Days
Maldah, West Bengal
₹0
₹5.4 L
10 Jun 2026
19 May 2026
27 May 2026
90 items across 10 schedules · ₹2,69,02,915.71 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Supply, Installation, wiring, testing and commissioning of Multi Section Digital Axle Counter (Detection points and Evaluators as per the Scheme) along with Toolkit, as per RDSO Specification No. RDSO/SPN/176/2013, Ver.3 or latest and as per Annexure-A. The warranty of the equipment shall be 2 YEARS from the date of commissioning. Inspection: RDSO. Note:- (1) Scheme of Main/Redundant (dual) Evaluators with approximate number of DPs connected shall be enclosed for each location of Evaluators. (2) Installation, wiring, testing and commissioning of MSDAC as per RDSO TAN/Guidelines and Annexure-B. | Per Detection Point (DP) | 35.00 | 3,29,883 | 1,15,45,905 |
| 2 | Supply of Track Lead Junction Box (TLJB) made from FRP material including brass bolts and hylam board sheet with 4 terminals as per ER drawing no- SI/TYP/0096 & ER Technical circular policy no-118 (Modified). Inspection: RITES/CONSIGNEE. The technical specifications of TLJB are as follows: (a) TLJB complete with cover to be in black/red having approximate weight of 4.0 Kg. with L- 262 mm. W-212 mm. and H-90 mm. and all the holes required for mounting on FRP stump (vertical two for each FRP angle) HDPE pipe , cable etc. (b) Each TLJB shall have two bakelite terminal block fitted horizontally: each bakelite terminal block shall have two nickel chrome plate M10 brass terminal, 50 mm. long. Along with each TLJB, nickel chrome plated brass links (two nos. of adequate strength for vertical linking of the terminals to be supplied. (c) HDPE pipe of size 32/35 mm., 380 mm. long, along with two nuts for fixing on the TLJB hole . (d) The FRP stump for mounting the TLJB to be made of one meter long 30 mm. X 30 mm. X 4 mm. angle (2 nos.) and 300 mm. long 30 mm. X 30 mm. X 4 mm. angle (1 no.) fixed at 50 mm. from the bottom using galvanised nuts and bolts. The TLJB and the angles for stump should come along with holes on them for fixing using galvanised nuts and bolts of adequate strength to be supplied along with TLJB. Inspection: RITES/Consignee. | Numbers | 80.00 | 4,507 | 3,60,560 |
| 3 | Supply of Cable Clamp Assembly for sleeper ( Galvanised) for dressing of Jumpers crossing the Rail. As per the drawing attached in the Annexure-C | Numbers | 80.00 | 1,028.8 | 82,304 |
| 4 | Erection, Fitting and Rail connection of Track Lead Junction Box on two supports (FRP stumps ) with contractor's fixing material .This will include drilling of holes for track lead/side connections on rail. The work shall be done as per instructions of Rly engineer at site. Inspection: Consignee | Numbers | 50.00 | 1,316 | 65,800 |
| 5 | Supply of 40 mm. dia. permanently lubricated HDPE telecom: ducts (with chord) as per RDSO Spec. No. RDSO/SPN/TC/45/2013 Rev.2.0 with latest amendments or Latest in length of 1000 mtrs./roll For each km. of HDPE duct following items are to be supplied (a) end plugs-2 nos. (b) cable sealing plugs - 2 nos. (c) plastic couplers slip fit/push fit type-2 nos. (d) end plugs to be provided along with drum 2 nos. Color to be specified by Railways. Inspection: Consignee. | Kilometre | 1.00 | 79,596 | 79,596 |
| 6 | Fixing of Cable Clamp Assembly with Sleeper along with placing of HDPE Pipe and fixing of Jumper ( Track, MSDAC etc.). This work includes Preparation of jumper, placing through HDPE pipe, proper termination of jumper in TLJB and rail along with required drilling in rail. Note:- i) No. in the Unit column indicates per Sleeper ) ii) Two or three Clamps in each sleeper. iii) Jumper cable will be supplied by railway. | Numbers | 42.00 | 1,461.16 | 61,368.72 |
| 7 | Supply of desktop/All in one PC as per following specifications. Intel i3, 12th generation or better, RAM - 8 GB, SSD - minimum 256 GB, display - 21.5 inch, Window-10 or higher, graphics Type - integrated, Keyboard & mouse - wireless. Make: HP/Lenovo/Dell or better. Inspection: Consignee. | Numbers | 1.00 | 50,793 | 50,793 |
| 8 | Supply of Steel Plain Almirah with 4 adjustable slaves. Size: 1980 mm. height, 915 mm. width and 485 mm. depth. Make: Godrej Storewel Plain Large or Better of reputed brand. Inspection: Consignee. | Numbers | 2.00 | 21,636 | 43,272 |
| 9 | Supply of Office table with laminated top with three drawers on left hand side and one locker on the right hand side. Olive brown with duplicate keys. Make: Godrej Model T-9 (136.5 cm. X 68 cm. X 75 cm.) or Superior of reputed brand. Inspection: Consignee. | Numbers | 2.00 | 16,244 | 32,488 |
| 10 | Supply of Portable operator console for onsite programming of Axle Counters as per technical requirement given in tender document. Inspection: Consignee | Set | 1.00 | 76,514 | 76,514 |
| 11 | Supply of B Type Choke as per RDSO Spec. No. IRS:S- 65/83 (Amnd.1) or latest. Inspection: RDSO. | Numbers | 100.00 | 6,026 | 6,02,600 |
| 12 | Supply of Channel Pins MS (Galvanized) single groove, 7 mm. suitable for 4 mm. dia. bonding wire as per Spec. No. IRS S-17 & RDSO Drg. No. S-69/M. Inspection: Consignee. | Numbers | 5000.00 | 5 | 25,000 |
| 13 | Supply of GI wire 8 SWG (4 mm. dia.) suitable for track circuit rail bonding. Inspection: Consignee. | Metre | 5000.00 | 8 | 40,000 |
| 14 | Supply of Siemens Parallel Input Module (PIM50) Inspection: RDSO. | Numbers | 1.00 | 2,73,900 | 2,73,900 |
| 15 | Relay Output Module (ROM50) Inspection: RDSO. | Numbers | 1.00 | 2,79,600 | 2,79,600 |
| 16 | Supply of Signal conditioner card -1/ Signal conditioner card -2 (SCC-1/SCC-2) card for CEL make HASSDAC/SSDAC as per RDSO Spec.no: RDSO/SPN/177/2012, Version 3.0 or latest. Inspection: Consignee. | Numbers | 4.00 | 38,134 | 1,52,536 |
| 17 | Supply of Modem/Communication card for CEL make HASSDAC/SSDAC as per RDSO Spec.no: RDSO/SPN/177/2012, Version 3.0 or latest. Inspection: Consignee. | Numbers | 2.00 | 38,350 | 76,700 |
| 18 | Supply of Relay Drive card for CEL make HASSDAC/SSDAC as per RDSO Spec.no: RDSO/SPN/177/2012, Version 3.0 or latest. Inspection: Consignee. | Numbers | 1.00 | 38,370 | 38,370 |
| 19 | Supply of DC-DC converter card for CEL make HASSDAC/SSDAC as per RDSO Spec.no: RDSO/SPN/177/2012, Version 3.0 or latest. Inspection: Consignee. | Numbers | 2.00 | 20,768 | 41,536 |
| 20 | Supply of Micro Controller Logic card -1/ Micro Controller Logic card -2 (MLB-1/MLB-2) card for CEL make HASSDAC/SSDAC as per RDSO Spec.no: RDSO/SPN/177/2012, Version 3.0 or latest. Inspection: Consignee. | Numbers | 2.00 | 52,805 | 1,05,610 |
| 21 | Supply of LaserJet Mono Printer for A4 Paper Size as per following specifications. Connectivity USB & Wi-Fi, monochrome, Mobile Printing Capability through smart app, Print Speed Black - Up to 21 ppm., Duty Cycle monthly - Up to 10,000 pages, function type - print only. Make: HP/Canon/Epson or better. Inspection: Consignee. | Numbers | 2.00 | 13,889 | 27,778 |
| Schedule total | ₹1,40,62,230.72 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
LetterofcreditAnnexure-B.pdf
ATTACHMENT
AnnexureVIBContractualTurnoverGCC2022.pdf
ATTACHMENT
Tele_Cir_9-20231.pdf
ATTACHMENT
GCCACSNo.5.pdf
ATTACHMENT
GCCACSNo.1.pdf
ATTACHMENT
AnnexureUV_1.pdf
ATTACHMENT
AnnexureU-VII.pdf
ATTACHMENT
AnnexureU-VI.pdf
ATTACHMENT
GCC2022_1.pdf
ATTACHMENT
REVISED_FORMAT_FOR_CERTIFICATE_28042023.pdf
ATTACHMENT
AnnexureIV.pdf
ATTACHMENT
AnnexureU-VIII.pdf
ATTACHMENT
GCCACS.pdf
ATTACHMENT
AnnexureIAnnexureIIandAnnexureIII.pdf
ATTACHMENT
GCCACSNo.2.pdf
ATTACHMENT
GCCACSNo.3.pdf
ATTACHMENT
GCCACSNo.6.pdf
ATTACHMENT
GCCACSNo.4.pdf
ATTACHMENT
GCCACSNo.9.pdf
ATTACHMENT
GCCACSNo.7.pdf
ATTACHMENT
TechnicalcircularNo.123regardingPVCInsulatedRailwaySignallingIndoorSingle_Multicorecable.pdf
ATTACHMENT
GCCACSNo.8.pdf
ATTACHMENT
TECHNICALSPECIFICATIONS3.pdf
ATTACHMENT
GCCACSNo.10.pdf
ATTACHMENT
GCCACSNo.11.pdf
ATTACHMENT
ChangesinBGFormat.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .