CONSTRUCTION OF TRAINING OFFICE AT ARMY MARKSMANSHIP UNIT INF SCHOOL UNDER GE MIS MHOW

Amount

Surface dressing n exc 30 cm deep in soft/loose soil complete all as specified and directed.

Earth work in excavation of all kind of soil by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.50 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.50 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m complete all as specified and directed.

All as per item No 2.00 above but exceeding 1.50 m but not exceeding 3.00m depth

Earth work in excavation of all kind of soil by mechanical means (Hydraulic excavator) means over areas (exceeding 30 cm in depth, 1.50 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.50m complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering as required complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete and sub base of floor complete all as specified and directed.

M&L for cement concrete (1:3:6) type C2 using 40mm graded stone aggregate in filling sub base, base complete all as specified and directed.

M&L for RCC M-25 (design mix) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs and mass concrete and like complete all as specified and directed.

M&L for RCC M-25 (design mix) as in Slabs supported on walls, ,chajjas, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for RCC M-25 (design mix) as in roof beam, lintel beams complete all as specified and directed.

M&L for RCC M-25 (design mix) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

S&F Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, footing, roof beam, plinth beam, slab,chajjas and similar work hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 13.00 above but 5 mm dia and over up to and including 10 mm dia as in stirrups

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc. complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions etc complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

M&L for brickwork with modular fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed.

M&L for 10 mm thick rendering in CM 1:6 on brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:4 on brick work or concrete surfaces, surfaces finished even and smooth without using extra cement including water proofing chemical @200mml per bag of cement complete all as specified and directed.

M&L for glazed ceramic coloured tiles 450mm x 300 mm size 6 to 7mm thick in dados or skirting over and including rendering 10mm thick in CM (1:4), jointed in neat grey cement slurry and pointed in white or colour cement to match the tiles as directed and specified.

M&L for non skid/mat finish ceramic colour tiles 7 to 8 mm thick(square/ rectagular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm (Colour and design of tiles as approved by GE), in floors/SKIRTING etc, and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for vitrified double charge tiles of size 8 to 10 mm thick (light shade or dark shade) (Square/rectangular) area of each tile n exc 0.36 sqm, in floors, set & jointed in neat cement slurry and pointed in coloured cement over and including 15mm screed in CM 1:6 complete all as specified and directed.

M&L for vitrified double charge tiles of size 8 to 10 mm thick (light shade) (Square/rectangular) area of each tile n exc 0.36 sqm, in dado/skirting set & jointed in neat cement slurry and pointed in coloured cement over and including 10mm screed in CM 1:4 or with chemical cement to match complete all as specified and directed.

S&F vitreous china wash basin white (oval shaped under counter) of size 550mmX400mm , including cutting for and pinning in ends with & including MS adjustable brackets, or erecting stand, CP coupling, waste pipe complete all as specified and directed.

S&F padestal pattern Vitreous china wash down water closet pan white including trap,PVC seat cover white, and flush pipes and connection to drain (or out going pipe ) and to flushing pipe antisyphone pipe etc complete all as specified and directed.

S&F vitreous china urinal half stall type 350x390x600 mm (minimum) height with including spreader for urinal ,providing & fixing of plugs bedding against wall in cement mortar 1:2 pointing around urinal back in cement mortar complete all as specified.

S&F PVC valveless, syphonic action type flushing cistern,low/high level white with inlet ball valve float and handle including brackets complete fixrd capacity of flush 10 ltrs complete all as specified and directed.

S&F 75 mm bore PVC floor traps plain with C.P grating and 300 mm long out let including jointing and etc complete all as specified and directed.

S&F PVC (SWR) pipe, 75 mm bore, single socketed, in any length in floor with rubber ring joints and suitable bends wherever required complete all as specified and directed.

S&F PVC (SWR) gully trap 110 mm,setting and jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) pipe, 110 mm bore, single socketed, in any length with rubber ring joints, fixed to walls with clamps and bends wherever required complete all as specified and directed.

S&F PVC bends 75mm bore, any radius complete all as specified and directed.

S&F PVC (SWR) pipes of dia 110 mm single socketed in any length with rubber ring joints laid in trenches or in floors of dia 110 mm complete all as specified and directed.

S&F PVC (SWR) pipes of dia 160 mm single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) pipes of dia 75 mm single socketed in any length with rubber ring joints fixed to walls with clamps of dia 75 mm complete all as specified and directed.

S&F Bib taps (fancy type) cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe of 15mm bore complete all as specified and directed.

S&F fancy type chromium plated two way bib cock of 15mm bore ,screwed for iron pipe or brass ferrule etc complete all as specified and as directed.

S&F pillar taps (swan neck), fancy type cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore complete all as specified and directed.

S&F stop/angle cock cast copper alloy high pressure, angle valve type, chromium plated suitable for 15mm bore steel pipe complete all as specified and directed.

S&F health faucet 15 mm dia with flexible pipe of 1.25m length including abs wall hook for EWC complete all as specified and as directed.

S&F PVC connections of 450mm long of PRYAG Make suitable for 15mm dia iron pipe including PTMT nuts complete all as specified and directed.

S&F 15mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified and directed.

S&F 20mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified and directed.

S&F 20mm bore Gun -metal,globe or gate valves,with iron wheel head ,screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F rotational moulded polythylene 500 Ltr capacity water storage tank (double layer)(cylindrical/vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 20mm bore complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm vide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F towel rail 600mm long 20mm dia brass chromium plated fixed with wooden gulties embedded in cement mortar (1:3) with MS screws etc complete all as specified and directed.

S&F SS Toilet paper holder complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x125mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applyingPVC solvent cement and screwed with fullbody threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30 mm thick as directed by engr in charge, comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter all as per direction of Engineer- In- Charge.

S&F factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick with/without glass opening and fixing 4 mm glass as directed by engr in charge, comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter all as per direction of Engineer- In- Charge.

S&F 35 mm thick Factory made single extruded WPC (Wood Polymer Composite) solid plain glazed and skeleton shutters open rebated and prepared to to receive glass gauge etc with cut and mitred beads for securing glass etc size of member of shutterof comprising of virgin PVC polymer of K value 58-60 (Suspnsion Grade), calcium carbonate and natural fibres (wood powder/ricehusk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screws with full body threaded star headed SS screws having minimum frame density of 650 kg/cum , screw withdrawal strenght of 1800 N (Face) & 900 N (Edge) , minimum compressive strenght of 50 N/mm sqr , modules of elasticity 850 N/mm sqr and resistance to spread of flame of Class A category with property of being termite /borer proof , water /mositure prooof and fire retardant . WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x100mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applyingPVC solvent cement and screwed with fullbody threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge

S&F 100mm long butt hinges stainless steel complete all as specified and directed.

S&F 150 mm long stainless steel barrel tower bolts of extruded section complete all as specified and directed.

S&F stainless steel handles 150 mm complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 20mm graded stone aggregate) as in plinth protection Finishing surfaces of concrete topping even and fair (without using extra cement) including making joint at every 3 mtr interval and at corner and filled with mixture of bitumen and sand and finished even and fair and laid in alternate bays complete all as specified and directed.

M&L for preparation of newly plastered surface of wall,pilasters,cornices etc and applying two coats of Anti fungal weather coat acrylic emulsion paint including a coat of primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistance primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash on ceiling surface complete all as specified and directed.

S&F powder coated aluminium ventilator cross section 63.5x38.10x1.2mm consisting of two partions upper portion shall have louvers with 3mm thick pin headed glass and aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56m fixed with aluminium beads and securing on outer face of frame and lower portion of ventilation shall be fixed with 3mm thick pin headed glass with IDPE rubber gasket including aluminium beads, including preparation of jombs all around in CM 1:3 finishing even and smooth complete all as specified and directed.

M&L for 1mm thick wall care putty internal / external both over prepared surface to achive the surface even and smooth for painting complete all as specified and directed.

M&L for Stone dust filling under floors including watering and consolidation complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block (pre painted glosy finished) any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed.

S&F kerb stone factory made M-25 grade cement concrete in position at or near ground level to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

S&F false ceiling complete including framework for ceiling at all heights with integral densified calsium silicate reinforced with fibre and natural filler false ceilling tiles of size 595X595mm ofapprovedtexture, design and pattern pinhole 8mmthick semiperforated square edge tile having NRC( noise reduction cogfficient ) of 0.50(minimum) Light refluctance of 85% (minimum) Non combustable as per BS : 476(PART-4) fire performance as per BS : 476(PART 6&7) humidity resistence of 100% thermal conductivity <0.043W/m K as per ASTM 518:1991, intrue horizontal level suspended on interlocking metal powder coated T-grid of hot dipped galvanized iron section on silhouuetter proffile,stitched double webbed white with 1mm reveal proffile ( White/black) comprising of main-T runner of size 15X 32mm of lenght 3000mm, cross-T of size 15 X 32MM of lenght1200mm and secondary intermediate cross-T of size 15 X32mm of lenght 600mm to form grid module/framework of size 600X600mm,from ceiling using galvanized mild steel item, 8mm outer daimeter M-6 dash fasteners, 6mm dia threaded hanger rod and L- shape leval adjuster of size 85X25X2mm Galvanized iron perimeter wall angle of size 19 X 19mm of lenght 3000mm to be fixed on periphery wall/Partition with the help of plastic rawl plugs at 450mm cetre and 40mm long dry wall SS screws complete all as specified and directed.

M&L for providing water proofing treatment on inaccessible roof surfaces (horizontal and vertical surfaces) through authroised applicator of manufacturers comprising (a) Cleaning of new concerete surfaces properly and drying the surfaces and applying 10mm thick renderingover a coat of cement slurry mixed with WPC (b) M & L for applying a tack coat of Industrial bitumen grade of 85/25 at the rate of 1.2 Kg per Sqm including cleaning surfaces (1st coat for bonding material below membrane and 2nd coat on top of membrane. Each coat will be paid seperately.)(c) Applying a coat of Oxidised bitumen based solvent primer @ 0.30 Kg/Sqr mtr (d) providing 3mm thick APP (Ataclic Polypropylene) modified water proofing membrane with polyestar core, overlaps, sealed and bonded to the surfaces with torch application (e) Applying two coats of bituminous aluminium paint @ 200gm per sqr mtr (min) in two coats as per manufactueres instructions complete all as specified. Note: (a) Cost of water proofing compound shall deem to be included in unit rates quoted by contractors, (b) WPT Shall be done through Manufcturer or through authorised applicator.

S&F powder coated aluminum door with the following specification and making good the adjacent surfaces complete all as specified and as directed:- (a) Cross section of xchowkhat frame 101.60x44.45x2mm thick. (b) Cross section of hanging and meetng style 83x44x2mm thick. (c) Top rail of cross section 83x44x1.6mm thick. (d) Bottom rail of cross section 114x44x1.6mm thick. (e) Locking rail (middle rail ) of cross section 114x44x1.6mm thick. (f) 5 mm thick tinted glass including rubber guasket (g) Aluminum handle eisc type -02 Nos per shutter ( inside & out side). (h) Aluminum door stopper heavy duty-01 Nos per shutter. (i) Aluminum tower bolt 200mm long-01 Nos per shutter (inside). (j) Lock with key superior quality make and type as approved by GE openable both from inside & out side -01 Nos per shutter. k) 1 hydraulic door closer

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F Powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters glazed and one shutter wire mesh) shall be following specification complete all as specified and as directed by Engr-in-charge. (i) Windows frame of cross section 101mm x 44mm x 1.5mm thick. (ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm x1.1mm thick. (iii) Sliding shutter frame of cross section 40 x 18 x 1mm thick. (iv) 4 mm thick tinted glass superior quality. (v) IDPE Rubber guasket for fixing of glass. (vi) Locking cleats per shutter -01 Nos. (vii) Sliding rollers per shutter - 02 Nos. (viii) S.S wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56mm for shutters 01 Nos.

M&L for Granite 18 mm thick(of any type) work (table rubbed and polished) for wall lining (Veneering to wall) , partitions for urinal or laid on cill/floors over and including 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite colour Red or brown as per direction of GE complete all as specified and directed.

S&F 25mm dia Stainless steel curtain rod of 1 mm thick fancy type fixed with modren bracket & doms design & sample approved by Engr -in Charge/GE complete all as specified and directed

S&F Solid PVC Wall Lining/cladding consisting of 5mm thick wood grain colour/ coloured PVC sheet inclusive of solvent cement including fixing at site on PVC frame including necessary moulding, corner profiles ets as per specifications complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in cills, steps, seismic and other similar bands, plinth courses, string courses, parapets and railing upto 60 cm in height, coping, kneelers, apex stones bed plates, etc and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary use and waste of form work complete all as specified and directed.

Rounding to edges of stone slabs one edges, such as in steps, cooking platform, and other similar situations for bullnosing / moulding to exposed edges( any type) and polishing to match the adjoining surfaces complete all as specified and directed.

S&F aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

M&L for preparation of new or previously untreated steel and iron surfaces of any description, not otherwise description, over 10 cm width or girth apply two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal with access door 110mm bore pipes complete all as specified and directed.

S&F PVC (SWR) vent cowl, 110mm bore complete all as specified and directed.

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling surface finish even and smooth without using extra cement complete all as specified and directed..

S&F bottle trap 32 mm bore of PTMT having minimum water seal of 25mm complete all as specified and directed.

S&F 10 mm thick frameless toughened glass ( colour as approved by engineer in charge ) including providing and fixing end sides with requisite stainless studs / brackets complete all as specified and directed by Engr-in-Charge.

M&L for brick bats for loose filling broken to gauze exc 63 mm and n exc 100 mm complete all as specified and directed.

M&L for brickwork with flyash bricks in one brick thick honeycomb work, straight or curved on plan exc 6m mean radius, built in CM (1:4) complete all as specified and directed.

S&F vertical blinds , consisting of aluminium head rails, vanes/louvers of 100 mm wide approved tint and traverse cord fixed in position complete all as specified and directed

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in cills, steps, seismic and other similar bands, plinth courses, string courses, manhole, parapets and railing upto 60 cm in height, coping, kneelers, apex stones bed plates, etc and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary use and waste of form work complete all as specified and directed.

M&L for Point wiring using approved colour coding as as per IS iwith FR LS PVC insulated PVC unsheathed electric cable 1100V grade ISI 694 marked down through single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area drawn in & including non metallic rigid PVC conduit ISI marked medium grade not less than 25 mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good and matching disturbed surface of wall with existing surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit surface casing caping will be used) & 1.5 sqmm green FR LS PVC insulated unsheathed copper conductor as earth wire connected to earth dolly by providing lugs including galvanised boxes and bakelite sheet for mounting switches, sockets, fan regulators etc for the following:- Make of PVC conduit :- Plaza/Finolex/Polycab/Kalinga/Jindal/Asian Make of cable - Havells / Finolex / RR Kabel Ltd. / L&T/Make as per PS (a) One light point/fan point controlled by one switch

(b) One 5amps socket out let point controlled by one switch on same board with other switches.

(c) One 5amps socket out let point on independent board controlled by one switch.

All as per item No 90.00 above but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point on independent board including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

All as per item No 90.00 above but using 4.0 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for geyser point/AC point connecting to metal plug and socket DB incl necessary running of 4.0 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S&F Modular Switch , single pole, one way, and 5/6 Amp single module complete all as specified and directed.

S&F Modular Switch , single pole, one way, and 15/16 Amp single modulecomplete all as specified and directed.

S&F Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module complete all as specified and directed.

S&F Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module complete all as specified.

S&F Bell push modular 6 Amps single module complete all as specified and directed.

S&F Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified and directed.

S&F Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and directed.

M&L for Sub main wiring with four runs of single core FR LS PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including two runs PVC insulated unsheathed FR LS 6.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge. Make of PVC conduit :- Plaza/Finolex/Polycab/Kalinga/Jindal/Asian Make of cable - Havells / Finolex / RR Kabel Ltd. / L&T/Make as per PS Note:- Four runs of main copper conductor, two run of earth wire and one run of PVC conduit shall be measured as one unit length.

S&F sheet metal enclosure MCB DB SPN 4 way, IP-43, IK 09 with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and directed.

S&F sheet metal enclosure MCB DB TPN 4 way, IP-43, IK 09 with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and directed.

S&F SPN MCB 32-40 Amp, 240 v, 50 Hz AC suitable for ‘C’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 complete all as specified and directed.

S&F TPN, MCB 32 to 63 Amp, 240 v, 50 Hz AC suitable for ‘C’ curve, 10 KA breaking capacity complete conforming to IS 8828 of 1996 complete all as specified and directed.

S&F single pole MCB 6 to 32 Amps, 240 v, 50 Hz AC suitable for ‘C’ curve, 10 KA breaking capacity conforming to IS 8828 of 1996, complete all as specified and directed.

S&F metal clad box suitable for 230 volt 50 Hz for AC and Geser connection three pin and socket with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed

S&F 1X18/20 W, 6500K V1 LED inverter batten with lithium ion battery charging time 8 hrs to 10 hrs and back up upto 10 hrs high efficiency with warranty option of 2 years from date of installation with and LED Life -Upto 50,000 Hrs all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes including taking down the existing complete all as specified and directed. Make:- Havells Cat No. LHEXASP7IN1W020 / Shakti cat Pt No. SZSLBMX018-iBB / /Bajaj/ Crompton/Phillips / Wipro/ Make as specified in Particular specification.

S&F LED ceiling light fittings 34/36 watt recess mounting type 2x2 luminaire, white light LED or warm light LED 5700K as per site requirment complete with driver duly connection wire etc including taking down the existing. Make Bajaj Cat Pt No. BZRSQL36LLEDGXWH /Havells/ Crompton/Phillips / Wipro/ Make as specified in Particular specification.

S&F LED round/square light fitting 15W surface mounting type, white light LED or warm light LED 6500K as per site requirment complete with driver duly connection with copper cable etc. Make, Havells Cat No. LHEAAHP7ILW012 /Bajaj/ Crompton/Phillips / Wipro/ Make as specified in Particular specification.

S&F decorative ultra slim LED light fitting 2 feet 10 watts, 6500K batten aluminium extruded with end caps complete all as specified and as directed. Make: Cat No HEXBLP7IN1W009 of Havells /Bajaj/ Crompton/Phillips / Wipro/ Make as specified in Particular specification.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. Make- Havells/Bajaj/Crompton / Make as specified in Particular specification.

S&F energy efficient exhaust fan of PVC body 250 mm sweep Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall or fixing in aluminium fabricated windows including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted.

S&F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 30 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe 40 mm dia medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Make: Havells Cat No LHETAVU7PA7J030 /Crompton/Phillips / Wipro/ Make as specified in Particular specification.

M&L for Earthing complete with galvanized steel earth plate electrode 60cm x 60cmx 6 mm thick buried directly in ground ( earth pit not less than 2.25 meter deep below ground level) with the top edge of the earth plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate No.3 of MES SSR parts-I and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of PCC earth chamber in mix 1:3:6 type C-1 with 40 mm thick RCC 1:2:4 type B-1 cover reinforced with 8mm dia MS bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia GI light grade and 15mm dia light grade pipe for earth lead protection and testing on completion, complete all as specified and directed including testing on completion.. Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted.

Cutting existing pipeline 80mm CI/DI for inserting CI tee of size 80X50X80 mm complete all as specifie and directed

Excavation in trenches not exc 1.50m wide & not exc 1.50m in depth for foundation etc or for shafts , wells, cesspits, manholes, laying of pipe, cable and exc 10 sqm on plan and n exc 1.50 m in depth getting out in in any type of soil complete all as specified and directed.

Returning filling in, including spreading, levelling watering & well ramming in layers not exc 25cm thick complete all as specified and directed.

Removing excavated material to a distance not exc 50 m & depositing where directed at a level not exc 1.50m above the starting point complete all as specified and directed.

Supply, laying, jointing and testing GI tubing of bore 50mm medium grade with one socket both end threaded in any length including cutting threading connection in new or old position and all type of GI new fittings for laid in trenches/wall/ceiling/ floor/ all as specified and directed.

Supply, laying, jointing and testing GI tubing of bore 20mm medium grade with one socket both end threaded in any length including cutting threading connection in new or old position and all type of GI new fittings for laid in trenches/wall/ceiling/ floor/ all as specified and directed.

Supply, fixing, jointing and testing non return valve (NRV) suitable for GI tubing of size 50mm bore of following bore size, (ISI Marked) both ends flanged and drilled for jointing including two flange joints and jointing material such as nuts, bolts washers rubber packing etc complete all as specified and as directed.

S&F Gun metal gate valve of size 50mm (ISI marked) with spindle and iron wheel, both ends screwed, iron pipe of following bore size including fittings and fixtures, as required, complete all as specified and as directed.

S&F Gun metal gate valve of size 25mm ISI marked) with spindle and iron wheel, both ends screwed, iron pipe of following bore size including fittings and fixtures, as required, complete all as specified and as directed.

M&L for construction of valve chamber 600 x 600 x 600 mm (internal dimensions), 6 mm thick MS sheet cover with 2 Nos MS hinges welded to angle iron frame of 40x40x6mm thick with lifting hook and locking arrangement complete with necessary earth work, brick work in cement mortar (1:6), PCC bed (1:4:8) type D2 (using 40 mm graded crushed stone aggregate) 150 mm thick, cement plastering 15 mm thick in cement mortar (1:4) and applying two coats of synthetic enamel paint over a coat of primer to the steel surfaces complete all as specified and directed.

Supply, laying, testing and commisioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trenches/ducts, on poles etc of size 3.5 core x 120 Sqmm complete all as specified and directed.

Supply, laying and jointing GI pipe 'light grade' 40 mm bore in trenches/under floors or roads/ along poles/ on wall incl clamps for protection of cables incl fittings complete all as specified and directed.

M&L for clean and dry sand (un-washed) in trenches including spreading and levelling for cushioning of UG cable complete all as specified and directed. Note:Punned thickness shall be measured

Supply and laying reinforced precast concrete cable cover, class LV, type 1 flat , size 250mm x 150mm x 40mm complete all as specified and directed.

Supply, installation, testing and commissioning LT Panel outdoor type (CPRI approved) mounted and fixed with PCC foundation, made out of MS sheet factory assembled & factory fabricated out of 3.15 mm thick sheet steel with suitable size MS angel frame duly spray painted with two coats of gray synthetic enamel paint over one coat of red oxide zinc chrome primer after preparatiion of surface, with required civil works & with and including 4 Nos Aluminium bus bars 400 Amps with suitable size porcelain insulators & wiring with copper cable of suitable size, connecting including indicating lamp LED type for each phase, incl in built industiral type locking arrangement, front operated and back openable incl necessry arrangement for fixing with suitable clamps, nuts & bolts etc. The panel pre wired with PVC insulated copper conductor danger notice board, feeders marked complete all as specified and directed:- Incoming : MCCB 250A, 4 pole, 25KA-1 No.,RYB Indication lamp, Digital Ampere Meter . Digital Volt Meter ,125A/5A,5VA,CL.1, CT – 3nos,Fuse Terminal Block with 2A Fuse-6nos. Outgoing : connecting the following switch gear: (i) MCCB125 A, 4 pole, 415 volts, ‘C’ curve, 25 KA - 03 Nos (ii) MCB, 40A TPN amps, 240 volts, ‘C’ curve, 10 KA - 02 Nos

Sudarshan Associates (BID ID -3504820)

sunway associates (BID ID -3510095)

m/s bansal construction (BID ID -3503915)