REPLACEMENT OF LT ELECTRIC LOAD DISTRIBUTION SYSTEM AT SPE AREA AT CAMERO COMPLEX, PROVN OF PUMP SETS AT CHOC BLDG OF HQ WAC AT SUBROTO PARK , PROVISION OF SPLIT AIR CONDITIONERS FOR SERVER ROOM AND UPS ROOM OF CSDO AT CAMERO COMPLEX AND PROVN OF AC

M&L for taking down existing LT cable of various size from various buildings and keep in safe custody for Sch of credit including making good the disterbed surface of road/ path /hard standing etc using suitable materials complete all as specified and directed.

M&L for taking out of old defective LT panels/ Bus bar boxes etc from various places of OMQ SPE area including removing LT cable connection, earthing strips etc including making good the disturb surface complete all as specified and directed.

M& L for design Fabricate, supply and install cubicle type, LT panel board,outdoor type, totally enclosed,dust & vermin proof (protection class IP 65) front opening with self locking arrangment made out of Stainless steel of 2.00mm thick (SS316). The fixing of double doors shall be on SS hinges with anti theft provision . all fabrication /welding shall be done with TIG/MIG or as approved by Engr-in-Charge suitable for SS 316. Sliding handle and locking arrrangnment front and rear both side. Enclosure shall be suitable for AC supply system 415 volts,50 Hz, 3 phase 4 wire degree of protection shall be IP -54 The enclousre shall have provision of cable entry. cable entry from bottom side including wiring with suitable size of PVC insulated, multi stranded solid copper cables 1100 volts grade. The panel consist of 1500 Amps rating TPN aluminum bus bars and shall be provided with colour coded heat shrinkable sleeves.all connected acessories required for functioning of panel board such as Lugs, glands, bolts, nuts,washers etc including supply and fixing following acessories:- The panel shall be provided with separate compartment s for each gear, including instrumention such as Multi function meter, phase indicatiing lamps etc with double stud hinged door, front & rear openable with locking arraggnment including interlocking with switch gears and suitable for 1100 Volts grade 3 phase 415 Voldts 50 Cycles, AC supply and to with stand short circuit fault level of not less than 10KA. The panel shall be fixed with angle iron frame made of angles of size 50x50x6mm embdedded 200mm below grond level in PCC 1:2:4 Type B-1 using 20mm grade stone aggregate 600mm above ground level and comprising the following. INCOMING (a) ACB 1000 Amps, 4 pole, DMX SP 2500, 50 KA drowout version of cat No 669540 of make Legrand equvilent - 1 Nos. (b) Digital type volt meter - set 01 (c) Digital type ammeter with suitable rating CTs conforms to relevent IS specification,- set 01 (d) LED type indicator lamp set of red , yellow and blue - set 01 OUT GOING (a) MCCB 400 Amps, 4 pole, 36 KA DPX3 630 cat No 422063 -03 Nos for Ics = 100% Icu (b) MCCB 250 Amps, 4 pole,36 KA DPX3 250 cat No 420249 - 03 Nos Ics = 100% Icu (c) MCCB 125 Amps, 4 pole, 25 KA DPX3 160 cat No 420096 - 02 Nos.(Out going to DAV Sunkul), Ics = 100% Icu

M& L for design Fabricate, supply and install cubicle type, LT panel board,outdoor type, totally enclosed,dust & vermin proof (protection class IP 65) front opening with self locking arrangment made out of Stainless steel of 2.00mm thick (SS316). The fixing of double doors shall be on SS hinges with anti theft provision . all fabrication /welding shall be done with TIG/MIG or as approved by Engr-in-Charge suitable for SS 316. Sliding handle and locking arrrangnment front and rear both side. Enclosure shall be suitable for AC supply system 415 volts,50 Hz, 3 phase 4 wire degree of protection shall be IP -54 The enclousre shall have provision of cable entry. cable entry from bottom side including wiring with suitable size of PVC insulated, multi stranded solid copper cables 1100 volts grade. The panel consist of 1500 Amps rating TPN aluminum bus bars and shall be provided with colour coded heat shrinkable sleeves.all connected acessories required for functioning of panel board such as Lugs, glands, bolts, nuts,washers etc including supply and fixing following acessories:- The panel shall be provided with separate compartment s for each gear, including instrumention such as Multi function meter, phase indicatiing lamps etc with double stud hinged door, front & rear openable with locking arraggnment including interlocking with switch gears and suitable for 1100 Volts grade 3 phase 415 Voldts 50 Cycles, AC supply and to with stand short circuit fault level of not less than 10KA. The panel shall be fixed with angle iron frame made of angles of size 50x50x6mm embdedded 200mm below grond level in PCC 1:2:4 Type B-1 using 20mm grade stone aggregate 600mm above ground level and comprising the following. INCOMING (a) ACB 1000 Amps, 4 pole, DMX SP 2500, 50 KA drowout version of cat No 669540 - 1 Nos. (b) Digital type volt meter - set 01 (c) Digital type ammeter with suitable rating CTs conforms to relevent IS specification,- set 01 (d) LED type indicator lamp set of red , yellow and blue - set 01 OUT GOING (a) MCCB 400 Amps, 4 pole, 36 KA -03 Nos Ics = 100% Icu with RHOM (b) MCCB 250 Amps, 4 pole,36 KA - 03 Nos Ics = 100% Icu with RHOM (c) MCCB 125 Amps, 4 pole, 25 KA - 03 Nos Ics = 100% Icu with RHOM

M& L for design Fabricate, supply and install cubicle type, LT panel board,outdoor type, totally enclosed,dust & vermin proof (protection class IP 65) front opening with self locking arrangment made out of Stainless steel of 2.00mm thick (SS316). The fixing of double doors shall be on SS hinges with anti theft provision . all fabrication /welding shall be done with TIG/MIG or as approved by Engr-in-Charge suitable for SS 316. Sliding handle and locking arrrangnment front and rear both side. Enclosure shall be suitable for AC supply system 415 volts,50 Hz, 3 phase 4 wire degree of protection shall be IP -54 The enclousre shall have provision of cable entry. cable entry from bottom side including wiring with suitable size of PVC insulated, multi stranded solid copper cables 1100 volts grade. The panel consist of 500 Amps rating TPN aluminum bus bars and shall be provided with colour coded heat shrinkable sleeves.all connected acessories required for functioning of panel board such as Lugs, glands, bolts, nuts,washers etc including supply and fixing following acessories:- The panel shall be provided with separate compartment s for each gear, including instrumention such as Multi function meter, phase indicatiing lamps etc with double stud hinged door, front & rear openable with locking arraggnment including interlocking with switch gears and suitable for 1100 Volts grade 3 phase 415 Voldts 50 Cycles, AC supply and to with stand short circuit fault level of not less than 10KA. The panel shall be fixed with angle iron frame made of angles of size 50x50x6mm embdedded 200mm below grond level in PCC 1:2:4 Type B-1 using 20mm grade stone aggregate 600mm above ground level and comprising the following. INCOMING (a) MCCB 320 Amps, 4 pole,36 KA DPX3 630 cat No 422006- 1 No Ics = 100% Icu (b) Digital type volt meter - set 01 (c) Digital type ammeter with suitable rating CTs conforms to relevent IS specification,- set 01 (d) LED type indicator lamp set of red , yellow and blue - set 01 OUT GOING (a) MCCB 125 Amps, 4 pole, 25 KA DPX3 160 cat No 420096 - 01 Nos Ics = 100% Icu (b)  MCCB 63 Amps, 4 pole, 25 KA DPX3 160 cat No 420093- 04 No Ics = 100% Icu

M& L for design Fabricate, supply and install cubicle type, LT panel board,outdoor type, totally enclosed,dust & vermin proof (protection class IP 65) front opening with self locking arrangment made out of Stainless steel of 2.00mm thick (SS316). The fixing of double doors shall be on SS hinges with anti theft provision . all fabrication /welding shall be done with TIG/MIG or as approved by Engr-in-Charge suitable for SS 316. Sliding handle and locking arrrangnment front and rear both side. Enclosure shall be suitable for AC supply system 415 volts,50 Hz, 3 phase 4 wire degree of protection shall be IP -54 The enclousre shall have provision of cable entry. cable entry from bottom side including wiring with suitable size of PVC insulated, multi stranded solid copper cables 1100 volts grade. The panel consist of 500 Amps rating TPN aluminum bus bars and shall be provided with colour coded heat shrinkable sleeves.all connected acessories required for functioning of panel board such as Lugs, glands, bolts, nuts,washers etc including supply and fixing following acessories:- INCOMING (a) MCCB 320 Amps, 4 pole,36 KA DPX3 630 cat No 422006- 1 No make Legrand and equvilent make of Simens/Schinder (b) Digital type volt meter - set 01 (c) Digital type ammeter with suitable rating CTs conforms to relevent IS specification,- set 01 (d) LED type indicator lamp set of red , yellow and blue - set 01 OUT GOING (a) MCCB 125 Amps, 4 pole, 25 KA DPX3 160 cat No 420096 - 01 Nos Ics = 100% Icu (b)  MCCB 63 Amps, 4 pole, 25 KA DPX3 160 cat No 420093- 03 No Ics = 100% Icu

M& L for design Fabricate, supply and install cubicle type, LT panel board,outdoor type, totally enclosed,dust & vermin proof (protection class IP 65) front opening with self locking arrangment made out of Stainless steel of 2.00mm thick (SS316). The fixing of double doors shall be on SS hinges with anti theft provision . all fabrication /welding shall be done with TIG/MIG or as approved by Engr-in-Charge suitable for SS 316. Sliding handle and locking arrrangnment front and rear both side. Enclosure shall be suitable for AC supply system 415 volts,50 Hz, 3 phase 4 wire degree of protection shall be IP -54 The enclousre shall have provision of cable entry. cable entry from bottom side including wiring with suitable size of PVC insulated, multi stranded solid copper cables 1100 volts grade. The panel consist of 250 Amps rating TPN aluminum bus bars and shall be provided with colour coded heat shrinkable sleeves.all connected acessories required for functioning of panel board such as Lugs, glands, bolts, nuts,washers etc including supply and fixing following acessories. The panel shall be suitable for 415 volts,50 Hz, 3 phase 4 wire system and shall be complete with 250 amp capacity copper bus bar, and saficient space for ATS 160Amp -01 Nos including wiring the panel board with suitable size of PVC insulated, multi stranded copper cables and all connected acessories required for functioning of panel board such as thimbles,glands, bolts, nuts,washers etc including supply and fixing following acessories The panel shall be provided with separate compartment s for each gear, including instrumention such as Multi function meter, phase indicatiing lamps etc with double stud hinged door, front & rear openable with locking arraggnment including interlocking with switch gears and suitable for 1100 Volts grade 3 phase 415 Voldts 50 Cycles, AC supply and to with stand short circuit fault level of not less than 10KA. The panel shall be fixed with angle iron frame made of angles of size 50x50x6mm embdedded 200mm below grond level in PCC 1:2:4 Type B-1 using 20mm grade stone aggregate 600mm above ground level and comprising the following. INCOMING (a) MCCB 160 Amps, 4 pole, 36 KA DPX3 250 cat No 4200 97 - 02 Ics = 100% Icu (b) Digital type volt meter - set 01 (c) Digital type ammeter with suitable rating CTs conforms to relevent IS specification,- set 01 (d) LED type indicator lamp set of red , yellow and blue - set 01 (e) Automatic transfer switch 160 Amps 4 pole, 50Hz at 440 Volts open execution including necessary bus bar for connection incoming cable complete-01 Nos Foundation- (i) Plateform for the panelwith PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation brick work in 1:6 with sub class"B" old size bricks sith sandering 15mm in CM1:6of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stomneaggregate on top plate form shall be such that it is of a height 45cm above nearest road level.

M& L for design Fabricate, supply and install cubicle type, LT panel board,outdoor type, totally enclosed,dust & vermin proof (protection class IP 65) front opening with self locking arrangment made out of Stainless steel of 2.00mm thick (SS316). The fixing of double doors shall be on SS hinges with anti theft provision . all fabrication /welding shall be done with TIG/MIG or as approved by Engr-in-Charge suitable for SS 316. Sliding handle and locking arrrangnment front and rear both side. Enclosure shall be suitable for AC supply system 415 volts,50 Hz, 3 phase 4 wire degree of protection shall be IP -54 The enclousre shall have provision of cable entry. cable entry from bottom side including wiring with suitable size of PVC insulated, multi stranded solid copper cables 1100 volts grade. The panel consist of 250 Amps rating TPN aluminum bus bars and shall be provided with colour coded heat shrinkable sleeves.all connected acessories required for functioning of panel board such as Lugs, glands, bolts, nuts,washers etc including supply and fixing following acessories. The panel shall be suitable for 415 volts,50 Hz, 3 phase 4 wire system and shall be complete with 250 amp capacity copper bus bar, saficient space for ATS 160Amp -01 Nos including wiring the panel board with suitable size of PVC insulated, multi stranded copper cables and all connected acessories required for functioning of panel board such as thimbles,glands, bolts, nuts,washers etc including supply and fixing following acessories INCOMING (a) MCCB 160 Amps, 4 pole,36 KA DPX3 250 cat No 420249 - 02 Nos 100% Icu (b) Digital type volt meter - set 01 (c) Digital type ammeter with suitable rating CTs conforms to relevent IS specification,- set 01 (d) LED type indicator lamp set of red , yellow and blue - set 01 (e) Automatic transfer switch 160 Amps 4 pole, 50Hz at 440 Volts open execution including necessary bus bar for connection incoming cable complete-01 Nos

M& L for Fabricate, supply and install cubicle type, CPRI approved LT panel board,outdoor type, totally enclosed,dust & vermin proof (protection class IP 65) front opening with self locking arrangment made out of Stainless steel OF 2.00mm thick (SS316). The fixing of double doors shall be on SS hinges with anti theft provision . all fabrication /welding shall be done with TIG/MIG or as approved by Engr-in-Charge suitable for SS 316. Sliding handle and locking arrrangnment front and rear both side. Enclosure sgall be suitable for AC supply system 415 volts,50 Hz, 3 phase 4 wire degree of protection shall be IP -54 The enclousre shall have provision of cable entry. cable entry from bottom side including woring with suitable size of PVC insulated, multi stranded solid copper cables 1100 volts grade. The panel consist of 250 Amps rating TPN aluminum bus bars and shall be provided with colour coded heat shrinkable sleeves.all connected acessories required for functioning of panel board such as thimbles,glands, bolts, nuts,washers etc including supply and fixing following acessories. The panel shall be suitable for 415 volts,50 Hz, 3 phase 4 wire system and shall be complete with 250 amp capacity copper bus bar, wiring the panel board with suitable size of PVC insulated, multi stranded copper cables and all connected acessories required for functioning of panel board such as thimbles,glands, bolts, nuts,washers etc including supply and fixing following acessories The panel shall be provided with separate compartment s for each gear, including instrumention such as Multi function meter, phase indicatiing lamps etc with double stud hinged door, front & rear openable with locking arraggnment including interlocking with switch gears and suitable for 1100 Volts grade 3 phase 415 Voldts 50 Cycles, AC supply and to with stand short circuit fault level of not less than 10KA. The panel shall be fixed with angle iron frame made of angles of size 50x50x6mm embdedded 200mm below grond level in PCC 1:2:4 Type B-1 using 20mm grade stone aggregate 600mm above ground level and comprising the following. INCOMING (a) MCCB 160 Amps, 4 pole, 36 KA DPX3 250 cat No 4200 97 - 02 Nos Ics = 100% Icu (b) Digital type volt meter - set 01 (c) Digital type ammeter with suitable rating CTs conforms to relevent IS specification,- set 01 (d) LED type indicator lamp set of red , yellow and blue - set 01 (e) Automatic transfer switch 160 Amps 4 pole, 50Hz at 440 Volts open execution including necessary bus bar for connection incoming cable complete-01 Nos Foundation- (i) Plateform for the panelwith PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation brick work in 1:6 with sub class"B" old size bricks sith sandering 15mm in CM1:6of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stomneaggregate on top plate form shall be such that it is of a height 45cm above nearest road level.

M& L for design Fabricate, supply and install cubicle type, LT panel board,outdoor type, totally enclosed,dust & vermin proof (protection class IP 65) front opening with self locking arrangment made out of Stainless steel of 2.00mm thick (SS316). The fixing of double doors shall be on SS hinges with anti theft provision . all fabrication /welding shall be done with TIG/MIG or as approved by Engr-in-Charge suitable for SS 316. Sliding handle and locking arrrangnment front and rear both side. Enclosure shall be suitable for AC supply system 415 volts,50 Hz, 3 phase 4 wire degree of protection shall be IP -54 The enclousre shall have provision of cable entry. cable entry from bottom side including wiring with suitable size of PVC insulated, multi stranded solid copper cables 1100 volts grade. The panel consist of 1200 Amps rating TPN aluminum bus bars and shall be provided with colour coded heat shrinkable sleeves.all connected acessories required for functioning of panel board such as Lugs, glands, bolts, nuts,washers etc including supply and fixing following acessories. The panel shall be suitable for 415 volts,50 Hz, 3 phase 4 wire system and shall be complete with 250 amp capacity Aluminium bus bar, saficient space for ATS 160Amp -01 Nos including wiring the panel board with suitable size of PVC insulated, multi stranded copper cables and all connected acessories required for functioning of panel board such as thimbles,glands, bolts, nuts,washers etc including supply and fixing following acessories :- The panel shall be provided with separate compartment s for each gear, including instrumention such as Multi function meter, phase indicatiing lamps etc with double stud hinged door, front & rear openable with locking arraggnment including interlocking with switch gears and suitable for 1100 Volts grade 3 phase 415 Voldts 50 Cycles, AC supply and to with stand short circuit fault level of not less than 10KA. The panel shall be fixed with angle iron frame made of angles of size 50x50x6mm embdedded 200mm below grond level in PCC 1:2:4 Type B-1 using 20mm grade stone aggregate 600mm above ground level and comprising the following. INCOMING (a) MCCB 160 Amps, 4 pole - 02 Nos Ics = 100% Icu with RHOM (b) Digital type volt meter - set 01 (c) Digital type ammeter with suitable rating CTs conforms to relevent IS specification,- set 01 (d) LED type indicator lamp set of red , yellow and blue - set 01 (e) Automatic transfer switch 160 Amps 4 pole, 50Hz at 440 Volts open execution including necessary bus bar for connection incoming cable complete-01 Nos Foundation- (i) Plateform for the panelwith PCC 1:2:4 type D-2 with 40mm graded crushed stone 15 cm thick in foundation brick work in 1:6 with sub class"B" old size bricks sith sandering 15mm in CM1:6of exposed surface and 100mm thick PCC padding 1:3:6 type C-1 using 20mm graded crushed stomneaggregate on top plate form shall be such that it is of a height 45cm above nearest road level.