MANUAL RESCUE AND OPERATION RESCUE, COMPREHENSIVE MAINTENANCE AND SPECIAL REPAIRS FOR REPLACEMENT OF 02 IN NOS OF 08 PERSON PASSANGER LIFT AGAINST BER AT 23A MHADA UNDER GE (NW) BHANDUP

Amount

Dismantling the existing BER Lift of capacity 8 Passenger lift (544 Kgs) of any make complete with all accessories such as reduction gear assembly ,Traction machine, electric motor control panel, guide rails and cabins, landing door and car door wire rope etc serving G+14 upper floor installed in bldg at 23 A Mhada and deposit to MES Store yard complete all as specified and directed by Engr-in-charge. Note :- Before carrying out dismantling work of a particular lift the contractor shall first produce the procurement order for the entire material required for installation of new lift after the contractor shall obtain permission in writting from Engineer-in-charge to carryout dismantling of the existing lift in bldg 23 A Mhada .

Supply, install, testing & commissioning 8 Passengers(544Kgs) Lifts suitable to serve G+14 upper floors in bldg (8 PS) suitable to serve G+14 upper floors with AC variable voltage & variable frequency (VVVF drive) drive with closed loop complete with all standard accessories, simplex down collective operation with or without attendent stainless steel doors with hairline finish, automatic rescue device (ARD) system, full beam infrared sensor in full height of door & built in announcing system without hand set (02 Nos, one each for car & ground floor and with one set in machine room ) all as specified below .

(a) Type of Lifts : 8 Passengers. (b) Load capacity : 544 Kgs. (c) Speed : 1.5 mtr/sec with single speed motor. (d) Power Supply : 400 volts, 3 phase AC, 50 Hz. (e) Type of Drive : AC variable voltage & variable frequency drive. (f) Type of Machine : Gearless & directly coupled Horizantal traction machine. (g) Total Travel : 37720 mm, (h) Overhead : 4400 mm (i) Car size (Inside) : 1300 Wide x 1100 Deep x 2200 Height (j) Car door and landing door at all floor : Automatic center opening with VVVF door drive, opening size 800mm x 2000mm, sliding type, fabricated by stainless steel sheet not less than 1.2 mm thick having hairline finish (N-304). (k) Car enclosure : Standard manufacturing with MS frame & stainless steel sheet not less than 1.5 mm thick with hair line finish (N-304), having stainless steel false ceiling with hairline finish, internal lighting arrangement with LED light fitting complete, internal vantilation system provided with concealed arial flow/cross flow fan with auto cut of system and stainless steel grill/wire mesh for protection. (l) Terminal buffers : Metal special spring buffers as per manufacturer specification. (m) Door opening (Inside) : Protected by automatic centre opening stainless steel doors with hairline finish doors with clear opening size 800mm x 2000mm. (n) Clear Hoist size : 1900 Wide X 1900 Deep (o) Car & counter weight Guide : Guide rails of `T' Section Mild steel 82 x 68 x 09 for car & 70 x 65 x 09 for CWT (p) Flooring : Stainless steel chequered plate 5mm thick.

(P) Signals :- (i) Combined luminous hall buttons with digital hall position indicators at all floor. (ii) Vaccum filled display (VFD) for car position indicator of stainless steel and overload warning in car. (iii) One No car operating panel with Luminious buttons in car (stainless steel) (iv) Car direction indicator in car & Landing. (v) Battery operated alarm bell & emergency light (rechargeable) along with suitable maintenance free battery. (vi) Overload warning feature in car cabine (display and announcing type both). (vii) Fireman’s switch one No per lift to be installed at ground Floor near landing door. (viii) All signal fixture & car operating panel on stainless steel face plate with hair line finish. (ix) Full beam infrared sensor safety edge of door for entire height. (x) Built in announcing system without hand set 02 Nos.( One each in car& near ground floor landing door & one announcing system with hand set in machine room). (xi) The interior of the car should be provided with a device that audibly indicates the floor position of lift car has reached and indicates that car entrance/exit door is open or closed. (xii) stainless steel hand rail 40 mm dia all around 3 inside the car cabin. (p) Stops & Opening : 15:15 ( All opening on same side). (q) Safety device : As per OEM design Automatic rescue device (ARD) /automatic landing device to be operating with maintenance free batteries for landing as specified.Make: As per OEM specifications and approved drawing and design.

(r) Operation : Simplex full collective, automatic operation with/without attendant. (s) Machine Room : Located above the hoist way. (Details as per appendix attached, however tenderer to inspect the sight before quoting). (t) Hoist-Way Constn : Existing at site, details as per Appendix attached however tenderer to inspect the site before quoting. (u) AC- VVVF drive shall be of make: (v) Control system shall be enclosed loop type. (w) Door shall have AC-VVVF controled close loop operated. (x) Civil work : Necessary civil work such as making good disturbed surfaces, modification to landing space to suit to car size,necessary foundation to machine and one coat of white wash to lift shaft etc. (y) Face plate shape shall be rectangular and stainlees steel in hairline finish. (z) counter weight shall be of cast iron as recommended by OEM. (za) One number electrically operated siren, operating voltage 240 volts having audible range of 0.3 Km including independent switch inside of car cabin and connecting cables from car cabin to machine room. The siren shall be installed at appropriate place. (zb) One toughened looking mirror(of best quality) of size 1000mm x 1000mm x 4mm thick with silvered sheet frame. (zc) One number LED light to be connected with UPS for emergency lighting purpose.

Dismantling and taking out old archtrave from landing door complete and disposing of the same to outside MD Land complete all as specified and directed by Engineer - in - charge.

Material & labour for 18mm thick mirror polished black granite slab, machine cut mirror polished cladding with chamfered/rounded edges approved decorative design including necessery PCC work granite slab & jointing in cement slurry and pointed in white cement mixed with pigement to match with shade of granite for lifts architrave at all floors complete all as specified and directed by Engr-in-charge.

Suppply and lay PVC insulated, armoured heavy duty electric cable with aluminimum conductor,1100 volts grade, cross sectional area 4 core 25 sqmm on wall of any height.The rate quoted by contractor includes existing Taking out old unserviceable cable

Suppply and lay PVC insulated, armoured heavy duty electric cable with aluminimum conductor,1100 volts grade, cross sectional area 2 core 10 sqmm on wall of any height.The rate quoted by contractor includes existing Taking out old unserviceable cable

Supply and laying aluminimum strip of size 25x4mm from test point to lift machine room over the porcelain insulator provided at interval of 50 cm in such a way that aluminimum strip should not touch to the wall and their should not be sharm bends/kinks etc. complete all as specified and directed.

Material & labour for earthing complete with galvanized steel earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level connected to galvanized earth strip 32 X 6mm by means of bolts, nuts and washers of galvanized iron or steel upto the test point all as shown in electrical plate No.3 of SSR Part-I connected to lifts including PCC earth pit with CI cover, GI funnel with wire mesh, GI protection pipe of 40 mm dia for earth lead and 20mm GI pipe for watering, excavation and earth work in any type of soil, filling the pit with charcoal and common salt surrounding the earth plate complete all as specified and directed by Engr-in-Charge including testing on completion.

Comprehencive maintenance (Routine , preventive , breakdown) (Daily, weekly, fortnightly, monthly, qtrly, half yearly, yearly maintenance) , during all type of weather/climatic condition for the any make,capacity of lifts type (geared or gearless, Auto or manual operated with or without VVVF drive system, with or without ARD system etc), maintaining the lift and connected equipments and accessories etc in serviceable condition round the clock (on all days including holidays), also maintaining the necessary documents and repair of fully automatic electriclly operated passenger lift of any make & 08 passanger capacity installed 02 Nos in building 23A Mahda comprising of all devices and accessories through out 12 months on all days including sundays and holidays for period of 03 years after expiry of defect liability period as shown below NOTE : Cost of all the maintenance,repairs and including replacement of components and parts that too for the specific lifts as indicated therein to keep the lifts in perfect serviceable condition shall be deemed to be included in the quoted rate of the contractor. The contractor shall be responsible for handing over the lifts in serviceable condition at the time of completion of works. The payment for replacement of parts/components expenditure upto Rs 1500/ is deemed to be included in the quoted rate.

For 1st year after expiry of defects liability period

2nd year after expiry date of item no 11.01

3rd year after expiry date of item no 11.02

Manning & Operation of fully automatic electrically operated 02 Nos, 08 passeger lift installed against Sch 'A' item Nos 02 here in before in building 23A Mahda in two shifts of 08 hours duration each i.e from 0600 hrs to 1400 hrs & 1400 Hrs to 2200 Hrs throughout 11 months on all days including holidays with providing rescue to the trapped person, maintaining the lift and connected equipments and accessories including lift room in clean and tidy condition during the operation period and also Manning & Operation of Lift in case of failure of commercial supply by running of DG Set installed within the vicinity meant for lift supply.complete all as specified and directed by GE. Notes : a) Quoted Rate shall be deemed to include to provide one alternative employee (reliever) to provide the services, so that the other employee can avail the facility of weekly leave etc. b) Cost of all the maintenance,repairs and including replacement of components and parts upto Rs 1500/- that too for the specific lift as indicated therein to keep the lifts in perfect serviceable condition shall be deemed to be included in the quoted rate of the contractor. The contractor shall be responsible for handing over the lifts in serviceable condition at the time of completion of works.

For a period of first 11 Months from the next day of completion of work

For a period of next 11 Months from the next day of completion of work of item No 12.01

For a period of next 11 Months from the next day of completion of work of item No 12.02

For a period of next 11 Months from the next day of completion of work of item No 12.03

For a period of next 11 Months from the next day of completion of work of item No 12.04

For a period of next 05 Months from the next day of completion of work of item No 12.05

Veer High Tech Solution

shakti engineering and electrical works

Escon Elevators Pvt Ltd