15th finance Commission - 2024 - 2025 1st Installment-Construction of Community Toilet at Ward-2 in Pannaipuram Town Panchayat

Amount

Earthwork excavation for foundation in all soils and sub soils in hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders and to full depth as may be directed,except in hard rock,requiring blasting including shoring and shuttering and bailing out of water wherever necessary,refilling the sides of foundation with excavated earth or sand in layer of not more than 15cm thick.well rammed and consolidated and depositing on bank with initial lead and lift of 10m & initial lift of 2m and depositing the surplusr earth within the compound in places shown by the departmental officers with iniital lead and lifts,clearing and levelling the site etc., complete as per SS20B and as directed by departmental Engineers(TNBP No.17,23,24). - 1 M3

Supplying and Filling in foundation and basement with Filling M- Sand in layers of not more than 15cm thick well rammed,watered consolidated including cost and conveyance of materials and labour charges etc., complete as per Standard Specification and as directed by departmental Engineers(TNBP No.24&25).

Plain Cement Concrete 1:4:8 mix (One Cement, Four Fine Aggregate and Eight Coarse Aggregate) Using 40mm ISS HBG metal for foundation and basement including dewatering if found necessary and laid in layer of not more than 15cm thick and consolidated including all cost conveyance of materials and labour charges etc. complete as per standard specifications and as directed by departmental Engineers (TNBP No.28).

Vibrated Reinforced Cement concrete 1:1 1/2:3 (One cement, one and half sand and Three aggregate) using machine crushed 20mm gauge hard broken stone jelly for all RCC items of work excluding centering strutting, and reinforcement grills placed in position but including mixing concrete, laying and vibrations charges, curing, etc complete and including providing fixtures like fan clamps in the RCC floor or roof slabs wherever necessary etc. complete complying with standard specification ( TNBP No:30)

Foundation and basement

Above Basement Ground floor

Supplying and erecting centering for sides and soffits including supports and strutting uptp 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90cmx60cm and 10 gauge stiffened, welded with mild steel angles of size 25mmx25x3mm for boarding laid over silver oak (country wood) joist of size 10cmx6.5cm dia spaced about 90cm centre to centre and supported by casuarina props of 10cm to 13cm dia spaced at 75cm centre tocentre etc.complete complying with standard specification and as directed by the departmental engineers. TNBP No.30

Without Strutting

With strutting Square Column

With strutting Plain surface

Supplying, fabricating and placing in position mild steel or ribbed tor steel for all reinforced cement concrete works as per design given including cost of steel and binding wire with all conveyance and lead charges in all floors etc.complete complying with standard specifications and as directed by the deparmental engineers. TNBP No:30

Brick Work in Cement Mortor 1:5 Mix (one cement, five M.sand) using best II Class Bricks of size 9 ” x 4 3/8 “x 2 3/4 ” from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications

Upto basement

Above basement

Laying with new C.C. Laminated tiles (Like Dora tiles Eurocon tiles etc),(anti skid) of 20mm thick of approved spl quality and set in Cement Mortar 1:3 (1 of cement and three part of P-sand ) 20mm. Thick using river sand and pointing with colour cement using at the rate of 0.40 kg/M2 and mixing with colour pigment at the rate of 0.3 Kg/M2 including finishing complete with Standard Specification and as directed by the Departmental Officers etc.,

Dadooing of walls with colour glazed tiles of size 300x200x6 mm finished thickness with c.m 1:2- and polished with same color cement including all cost and convene of all materials etc.,complete

Weathering course concrete using best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) over the RCC roof slab in the propotion of brick jelly to lime being 32:121/2 by volume and laid over in a single layer and consolidated to the required design and finished thickness , beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wetted by sprinkling lime jaggery water as per standard specification,etc.complete as directed by the departmental officers.TNBP No:44-I

Finishing the top of Roof with one course of machine pressed tiles of size ( 23x23x2 cm ) approved quality in C.M. 1:3 - 12 mm thick mixed with water proofing compoud confirming to IS @ 2 % by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc,. complete complying with Standard Specification

Manufacturing, supplying and fixing in position steel Windows / Ventilators of the following types; outer frames and shutter frames shall be made out of steel sections confirming to IS.7452 / 1990 t of ‘Z’ section (F.7D) of size 25mm x 20mm x 3mm and mullions are made of (F4B) ‘J’ sections of size 46mm x 25mm x 3mm and sash bars shall be made of ‘T’ section (T2) of size 25mm x 22mm x 3mm. including providing handle cum latch with suitable open shall be left for its easy operation and adjustable wind stay of sufficient length shall be provided for each shutter and with necessary MS angle hold fasts welded to the outer frame and 12mm MS square guard bars shall be welded to the inner flat of the window at equal intervals not exceeding 100 mm spacing and welding 18G MS sheet for panes and including one coat of red oxide primer and charges for fixing in position including dismantling the masonry, concrete and redoing the same duly packed with concrete etc., complete and as directed by the departmental officers

Supplying & fixing door shutters for Mediun Density Fiber Board of exterior grade 35 mm thick,single leaf conforming to IS:12406/1989 with 35x12 mm T.W.Lipping on all edges with necessary adhesives and CP screws complying with standard specifications. The rate is inclusive of threee coats of best quality varnish but excluding cost of furniture fittings.such as 300 mm tower bolt 2nos,200mm towerbolt I no. 300mm Aldrop 1 No. Alu handle ornamental type 2 Nos,and 1 No. Door stopper etc complete.

Supply and fixing of Terocotta jally including cost and conveyance of all materials and labour charges etc complete.

Supplying and fixing M.S Grill Gate, Grill to doors, special windows and ventilators etc using 20mmx6mm as directed by the departmental officers inclusive of cost of MS grill including one primer coat of red oxide and fixing in position etc. including cost and conveyance of all materials and all lobour charges etc.complete as per Standard specification and as directed by the departmental officers.(as per the schedule of rate)TNBP No:86 & 86-A

Special Ceiling Plastering with CM 1:3 (One part of cement & three parts of P-sand)mix for 10mm thick including cost and conveyance of materials to work site and including all labour charges for mixing, laying, curing,finishing etc., complete as per standard specifications and as directed by departmental Engineers – TNBP No:30,56&57

Plastering with CM 1:5 (One part of cement & five parts of P- sand) mix for 12mm thick including cost and conveyance of all materials to work site and including all labour charges for mixing, laying, curing,finishing etc., complete as per standard specifications and as directed by departmental Engineers – TNBP No:56&57

Plastering with cement mortar 1:3 ( one cement and three P.Sand) mix to 20mm thick including cost and conveyance of all materials to site including curing etc.,complete as per standard specification – 10m2

Painting two coats with ready mixed Plastic Emulsion Paint S.I.358 Plastic emulison paint of'approved quality and colour over a priming coat, including thorough scraping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required including cost and conveyance of all materials etc.and all lobour charges etc.complete as per Standard specification and as directed by the departmental officers. TNBP No:66-A.

Painting new iron works with two coats of approved quality and color of synthetic enamel paint over the existing red oxide primer in all floor etc., complete as per standard specification.

Supplying and fixing in position white glazed Indian water closet of size 580 X 440mm of Orissa type of approved quality with 'P' or 'S' trap with sand cushion and forming flooring alround the closet using 40mm broken brick jelly lime concrete 1:2:5 ; 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes by dismandling masonry / RCC works and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works.)

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14SWG TC wire and making good of the concealed portion with suitable colour SD 55

Wiring with 2x1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVCrigid pipe concealed in wall and ceiling with PVC accessoires with TW switch box and 5A F.T. switch in flush with wall with 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour forPVC concealed light point / fan point (For electronic regulator) SD 24

Supply and fixing of WT bulk head fitting with guard (Philips / Bajaj / Crompton / K. Lite) suitable for11W CFL lamp with CFL. SD 83

supplying and fixing of ISI approved make PVC pips, Specials

32mm pipe

25mm pipe

32mm Tee

32mm bend

32mm Coupling

25mm Tee

25mm bend

25mm coupling

32/25mm Reducer

25/20mm Reducer

PVC Tap

110mm PVC pipe

Supply and delivery and fixing of HDPE tank 1000 litres capacity as per IS 12701/ 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges as directed by departmetal officers.