Fabrication, Supply, Installation, Testing and Commissioning of Electrical Medium Voltage (MV) switchgear and panel works

Amount

SITC of wall/floor mounted type M. V. '4' Compartmentalized cubicle panel board suitable for 415 Volts, 50 Hz, A.C. Supply fabricated out of minimum 2.0 mm thick CRCA sheet, totally enclosed, dust and verminproof of minimum IP54 and doors with 1.6 mm thick CRCA sheet, with the following switch gears, interconnections with suitable size copper conductor wires between the busbar and out goimg switch gears complete with terminating arrangements, powder coating of minimum 60 micron thickness on the panel with approved shade and colour including earthing busbar (conforming to CPWD General Specification for Electrical works 2013 & amendments etc as required.) All items shall be ISI Marked & Including earthing connection as per CPWD standard as required TPN SDFU, MCB, Contactor & Timer Make: L&T/ Siemens/ Schneider/ Legrand/ ABB (a) 160A TPN SDFU with HRC Fuses along with CT coils, V, A, F meters, Watt hour panels meters etc., as required - 1 No's, (b) 100A TPN SDFU with HRC Fuses - 1 No's, (c) 63A TPN SDFU with HRC Fuses - 1 No's, (d) 5 HP DOL starter with suitable contactor, timer, relay, push buttons, voltmeter, Ammeter, Indication lamps etc., as required - 1 Set, (e) 10 HP Star Delta starter with suitable contactor, timer, relay, push buttons, voltmeter, Ammeter, Indication lamps etc., as required - 1 Set (f) 3 Phase, 63A Street light contactor with suitable timer, mcb, din rail, sheet etc., - 1 set (g) 300A 4 strip Aluminum bus bar (40x5mm) - 1 Set. (h) RYB phase indication & ON/OFF indication LED lamps (i) 2 mm CRCA Sheet (j) 75*40*6 mm MS channel for panel base (k) Man power, material, workmanship, transport, testing all inclusive (l) Nuts, fastners, powder coated painting, rubber beeding/gasket and panel wiring etc., as required

Supplying of 3.5 core * 70 Sq. mm, PVC insulated and PVC sheathed, XLPE armoured aluminum cable suitable for 1.1kV as per IS 7098 outdoor suitable as required Make: Havells/Polycab/Finolex

a) 3.5 Core x 70 sq. mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1kV grade of following size in the existing OPEN DUCT/ RCC/ HUME/ DWC/ HDPE/ GI pipe as required

(a) Above 35 sq. mm and upto 95 sq. mm

Supplying, excavation and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc., conforming to IS 14930, Part II complete with fitting and cutting, jointing etc., direct in ground (75 cm below ground level) including excavation and refilling the trench and concrete and refinishing as it is but excluding sand cushioning and protective covering etc., complete as required. Make: ISI Marked

(a) 90 mm dia (OD-90 mm & ID-76 mm nominal)

Supplying, excavation and laying of 300 mm dia Reinforced concrete heavy duty pipe of NP4 class, (As Per IS 458), Non Pressure Pipes with collars including cutting out pockets for collars, jointing in 1:1 cement mortar, cutting of pipes wherever required, curing and testing of joints, excavation, Drilling/Chipping, Laying Of Pipe, Back Filling Where Required etc., Complete as per specifications direct in ground (50 cm below thor road level) including excavation and refilling the trench/thor road and refinishing with 1:3:6 cement concrete ratio etc., complete as required. Make: ISI Marked

Supplying and making indoor end termination with suitable lugs, brass compression gland and aluminum lugs for following size of PVC insulated and PVC sheathed/XLPE aluminum conductor cable of 1.1 KV grade as required. Make: ISI Marked

(a) 3.5 Core x 70 Sq. mm (38 mm)

(b) 4 Core x 50 Sq. mm (35 mm)

(c) 3 Core x 25 sq. mm (25 mm)

(d) 3 Core x 16 sq. mm (25 mm)

(e) 4 Core x 16 sq. mm (28 mm)

Supply and providing of L = 6 meter, B = 4 meter shed with necessary minimum 2 mm thick GI roof sheet for the electrical panel along with MS square tube of size 50*50*2 mm, angle supports including cutting, wleding, fabrication, wind ties and painting etc., in the existing wall support with suitable height, including chipping, cement concrete and other necessary masonary works as required as per the directions of the Engineer - In - Charge.

SAIDAPET ELECTRICALS CHN PRIVATE LIMITED (BID ID -3184546)

KAVERI ELECTRICALS (BID ID -3184770)

BRILLIANT CONTROLS AND ENGINEERS (BID ID -3181662)

RMH CONTROL SYSTEMS (BID ID -3182547)