Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹9.1 CrAdmitted-Finance | ₹9.1 Cr | L1 | Admitted-Finance |
| 2 | L2₹9.7 CrAdmitted-Finance CHINAR COMMERCIAL COMPLEX THE BUND RESIDENCY ROAD SRINAGAR 190 001 | SRINAGAR | SRINAGAR | JAMMU AND KASHMIR | 190001 | ₹9.7 Cr | L2 | Admitted-Finance |
| Sl No | Description | Qty | Unit | M/S MOHAMMAD ASHRAF GILKAR ENGINEERS AND CONTRACTORS L1 | M M SHAWL ENGINEER AND CONTRACTORS PVT LTD L2 |
|---|---|---|---|---|---|
| 1.00 | Earth work in excavation by mechanical means over areas upto desired depth & width (with dewatering as required) including dressing of sides and bottom , disposal of surplus excavated material as directed by Engineer-in-charge including all leads, lifts and dewatering if any during execution of all operations of work complete.(All kinds of soil) | 2,916.25 | Cum | - | - |
| 2.00 | Earthwork in surface excavation not exceeding 30cm in depth but exceeding 1.5mtr in width as well as 10 sqm on plan including disposal of excavated earth upto 1mtr from cutting edge, lift upto 1.5 mtr., disposed earth to be levelled and neatly dressed in :
All kinds of Soil: | 1.05 | 100 Sqm | - | - |
| 3.00 | Extra rates for quantities of work due to slow progress & dewatering : 20% of rate of item | 2,639.25 | Cum | - | - |
| 4.00 | Providing and laying hand packed stone soling in foundation ,under floors etc. incl ramming, watering and consolidating complete ,cost and carriages of all materials involved upto site of work complete. | 301.7 | Cum | - | - |
| 5.00 | Providing and laying in position cement concrete of specified grade M-7.5 excluding the cost of centering and shuttering - All work at all levels in : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) including cost and carriage of all materials involved upto site of work complete. | 196.55 | Cum | - | - |
| 6.00 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m. | 732.2 | Cum | - | - |
| 7.00 | Supply and filling G.S.B. under floors including watering, ramming and consolidating with hand rammer with aggregate size not exceeding 90 mm including cost and carriage of all materials involved upto site of work complete. | 1,166.5 | Cum | - | - |
| 8.00 | Filling in with spilt nallah boulders (75mm to 150mm thick) under floor handpacked & rammed complete | 441.5 | Cum | - | - |
| 9.00 | Providing and laying in position cement concrete in M-10 grade concrete excluding the cost of centering and shuttering - All work up to plinth level: 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including cost and carriage of all materials involved upto site of work complete. (including carriage of materials from source to site) | 3.45 | Cum | - | - |
| 10.00 | Providing and laying in position cement concerete of specified grade 1:1:2
(1 cement: 1 coarse sand: 2 graded stone aggregate 20mm nominal size crushed aggeregate) for reinforced cement concrete works excluding the cost of centering, shuttering, and reinforcement. All work at all levels. M-25. | 1,935.34 | Cum | - | - |
Tender Value
₹10.3 Cr
EMD Value
₹20.5 L
Closing Date
27 Jan 2020, 4:00 pmClosed
AS PER THE NIT/SBD
AS PER THE NIT/SBD
Construction of Administrative Block and Store Building at Fire and Emergency Services Headquarter Batmaloo, Srinagar, JnK.
2020_PWDJK_90163_1
177/CDII/15222-32 of 2019-20 dated 09.01.2019
Open Tender
Civil Works
540 days
SRINAGAR
AS PER THE SBD
8 documents required · 8 mandatory
₹11,000
Yes
AS PER THE NIT/SBD
₹20.5 L
Yes
AS PER THE NIT/SBD
28 Apr 2020
10 Jan 2020
27 Jan 2020
10 Jan 2020
27 Jan 2020
20 Jan 2020
18 Jan 2020
Amount
Earth work in excavation by mechanical means over areas upto desired depth & width (with dewatering as required) including dressing of sides and bottom , disposal of surplus excavated material as directed by Engineer-in-charge including all leads, lifts and dewatering if any during execution of all operations of work complete.(All kinds of soil)
Earthwork in surface excavation not exceeding 30cm in depth but exceeding 1.5mtr in width as well as 10 sqm on plan including disposal of excavated earth upto 1mtr from cutting edge, lift upto 1.5 mtr., disposed earth to be levelled and neatly dressed in : All kinds of Soil:
Extra rates for quantities of work due to slow progress & dewatering : 20% of rate of item
Providing and laying hand packed stone soling in foundation ,under floors etc. incl ramming, watering and consolidating complete ,cost and carriages of all materials involved upto site of work complete.
Providing and laying in position cement concrete of specified grade M-7.5 excluding the cost of centering and shuttering - All work at all levels in : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) including cost and carriage of all materials involved upto site of work complete.
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m.
Supply and filling G.S.B. under floors including watering, ramming and consolidating with hand rammer with aggregate size not exceeding 90 mm including cost and carriage of all materials involved upto site of work complete.
Filling in with spilt nallah boulders (75mm to 150mm thick) under floor handpacked & rammed complete
Providing and laying in position cement concrete in M-10 grade concrete excluding the cost of centering and shuttering - All work up to plinth level: 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including cost and carriage of all materials involved upto site of work complete. (including carriage of materials from source to site)
Providing and laying in position cement concerete of specified grade 1:1:2 (1 cement: 1 coarse sand: 2 graded stone aggregate 20mm nominal size crushed aggeregate) for reinforced cement concrete works excluding the cost of centering, shuttering, and reinforcement. All work at all levels. M-25.
Reinforcement for R.C.C work including straightening, cutting, bending, placing in position & binding with binding wire all complete, Thermo Mechanically Treated Bars (500 D) (All work at all levels complete)
Providing form work including Centering ,shuttering , strutting, propping etc.using ply wood sheeting with water proofing ply board (12 mm min.thickness) and removal of the same for( All work at all levels complete.)
Foundations, footings, bases of columns etc
Lintels, beams, plinth beams, griders, bressumers and cantilevers
Columns, pillars piers, abutments, posts and struts
Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. :
Stairs, (excluding landings) except spiral staircases :
Suspended floors, roofs, landings, balconies and access plateform
Kota stone slab flooring over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) 25 mm thick
Masonry work with non load bearing cement concrete hollow blocks (1:4:8) of size 12"x 8"x 6"in super structure above plinth level upto floor level V level in: Cement mortar 1:4 (1 cement : 4 coarse sand)
Brick masonry with FPS bricks of class designation 75 in super structure upto floor V level in cement mortar 1:6 (1 cement:6cement coarse sand) comp-lete as per the directions of Consultant inculding cost & carriage of all materials involved upto site of work complete.
Half brick masonry with bricks of class designation 75 in super structure upto floor v level Cement mortar 1:3 (1 cement : 3 coarse sand) For exterior walls behind concrete hallow blocks
Providing & fixing wood work in frames of doors, windows & other frames, wrought framed & fixed in position including SS expansion fastners for brick/concrete work in (including cost of all material, leads, lifts & carriages etc upto site of work complete). Ist class Deodar Wood
15mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement : 6 fine sand) (including cost of all material, leads, lifts and carriages etc upto site of work complete).
6mm cement plaster to ceilings of mix 1:3 (1 cement : 3 fine sand)
Providing and applying cement based wall putty of required thickness over plastered surface to prepare the surface even and smooth complete in specified areas as per specified pattern. (Birla make) (including cost of all material, leads, lifts and carriages etc upto site of work complete).
Providing and fixing glazed shutters for doors, windows and clerestory windows using 10kg/sqm (4mm thick) float glass panes inluding ISI marked M.S pressed butt hinges bright finished of required size with necessary screws.First Class Kail Wood
Providing and fixing 35 mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm with wire of dia .0.63 mm for doors, windows and clerestory windows including I.S.I. marked black enameled M.S. butt hinges with necessary screws. (Ist.class kail wood.)
Providing and fixing 35mm thick paneled or paneling and glazed shutters for doors, windows and clerestory windows including I.S.I. Marked black enameled M.S. butt hinges with necessary screws excluding paneling, (which shall be paid for separately) (Ist class kail wood)
Providing and fixing paneling or paneling/ glazing in paneled or paneled & glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion in side grooves or rebates to be measured). Paneling for paneled or paneled glazed shutters.
Providing and laying vitrified floor tiles in different sizes (thickness to be specefied by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in all colours and shads, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. (Non-Skid & Normal) Size of tile 60 x 60 cm
Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge. (including carriage of materials from source to site)
Cement Concrete Flooring 1:2:4 (1 Cement : 2 Coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 50mm thick with 20mm nominal size stone aggregate
Providing & laying 18mm minimum thick pre-polished (best quality ) Granite stone slabs (non water absoring) in counters, vanities etc on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand)/12mm thick backing of cement mortar 1:3 (1 cement : 3 coarse sand) and joined with white cement slurry mixed with pigment or with standard tile made compound to match the shade of the slab. Including rounding, rubbing, clamping, curing, moulding, granite polish & making grooves as required complete (Note: The stone slab shall be cut to required size and laid to the required pattern including rounding, chamfering, bull nosing of the edges as directed. Actual area of slab, as laid shall be measured) Sample to be approved by Engineer-in-charge. (including cost of all material, leads, lifts and carriages etc upto site of work
Chequerred terrazo tiles 22mm thick with graded marble chips of size upto 6mm in floors jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing & polishing complete on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) light shade using white cement
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 13753 of miniumum thickness 6 mm of approved make like NITCO, ORIENT, SOMANY KAJARIA or equivalent make in all colours, shades except begundy, bottle green, black of any size as approved by the Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of Cement Mortar 1:3 (1 Cement : 3 Coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. sample to be approved by Engineer-in-charge. Sizeof Tile 450 x 300 mm. (including cost of all material, leads, lifts and carriages etc upto site of work complete).
Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads landings etc. of staircases including use of chequered plate wherever required; all complete.
A) in gratings, frames, guard bars, railings, brackets and smilar works
Providing & Fixing of budloo wood hand rail covered out of 75mm x 100mm section with necessary chamfers & rounding at top & sides including 40mm x 6mm recess at bottom to receive the steel rail top.
Structural steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including cost and carriage of all materials involved upto site of work complete.
Providing & fixing Precoated galvalume profile sheets 0.50 mm TCT having a crest height of 28-32mm at 195mm pitch and effective width of 975-1000mm and length to suit site requirement to the purlins using self drilling and self tapping fasteners of reputed make with purlin sheet using self drilling and self tapping fastners & Fixing flashings, valleys and ridges of colour coated galvalume plain sheet using self drilling and self tapping fasteners of reputed makel complete and as directed. The contractor shall give a minimum of 10 years guarantee for sheets against deterioration, disintegrations loss of luster, variation in colour, etc. and leakages across laps, fasteners etc. All types of steel sheets shall be load tested to satisfy 1.10 times the design wind load and coating thickness to the satisfaction of the Engineer-in-Charge. Fasterners shall also be load tested. The Contractor is to submit design and shop drawings for approval on the sheet profile, design and fabrication details before installation (including cost of all material, leads, lifts and carriages etc upto site of work complete).
Providing & Fixing of double glazing float glass in fixed panes with 19mm width predesiccated structural foam space (warm edge technology) thermal set spacer (Edge tec super spacer) in between the two glass plates with budloo wooden beading for outerside of outer pane and inner side of inner pane) of required width (glass panes to be measured in fitted and finished form)
a) Low-e cold glass both sides (for southern side only)
b) Long wave length IR radiation glass on outer side and low emission cold glass inside (for eastern, western & north side)
Providing and fixing plained eaves boarding of (300 x 40mm ) N/S with necessary grooves and chamfer as per detailed drawing.(ornamental) (Second Class Kail Wood) incl cost of nails.
P/F of 12mm thick T&G planks made of imported wood (New zealand pine or equivalent) for roof soffits & Ceiling on wood work in false ceiling, partitions sawn and putup in position in budloo wood (Ceiling Joists). including cost of necessary adhesive & cost of nails etc. with necessary cornice of required size complete job. incl cost of nails / screws all complete as approved by Engineer-in-charge (including cost of all material, leads, lifts and carriages etc upto site of work complete). Soffits
Applying priming coat on new wood and wood based surface with ready mixed wood primer (including cost of all material, leads, lifts and carriages etc upto site of work complete).
Painting with synthetic enamel paint of approved brand and manufacture of required shade and colour to give smooth finish with two or more coats on new wood and based surfaces
Providing and fixing of high density Polyethylene (HDPE) solid board resistant to scratches, dents impacts and graff it (Common scourage with bath room stalls) with required frame work for partitions & doors including all fittings and fixtures complete (to be measured and paid in finished form)
Supplying and fixing rolling shutters of approved make, made of required size M.S laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5 cm long wire springs manufacture from high tensile steel wire of adequate strength confirming to IS 4454 part 1 and m.S top cover of required thickness for rolling shutters. 80 x 0.90 mm M.S laths with 0.90 mm thick top cover
Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia, steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer
Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggreagate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.
Providing 40 x 5 mm flat iron hold fast 40 cm long including fixing to frame with 10mm diameter bolts, nuts & wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)
Providing & Fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanised with Zinc coating of 120gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex x 1.6mm thick with flanges of 27mm and 37mm, at 1200 mm centre to centre, one falnge fixed to the ceiling with dash fastner 12.5mm dia x 40mm long with 6mm ia bolts, other flange of cleat ixed to the angle hangers of 25 x 10 x 0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G.I channels 45 x 15 x 0.9mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5 mm at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clips made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing parimeter channels 0.55mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable or board, all as per manufactures specefication and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimeter channels suitably fixed all complete 12.5mm thick tapered edge gypsum plain board conforming to IS:2095 - Part 1
Providing/Fixing of door window stard wire fittings
A) T.Bolts
B) Handles
C) L-drops (Link)
SANITARY FIXTURES & CP FITTINGS:-FIXING ONLY
Providing & Fixing wall hung type white vitreous china European water closet with concealed `P' or ‘S’ trap, seat & lid (heavy duty) C.P. brass hinges, including C.I. chair, with chair grouting, rubber buffers, C.P. nuts, bolts, etc. including accessories CI / MS brackets painted with two coats of approved shade over a coat of primer, C.P. Brass screws and wooden cleats, including cutting and making good the walls & floors wherever required.
Fixing, testing & commissioning of white vitreous china squatting pan Orissa pan water closet (Orissa pan type of size 580 x 440 mm) with 100 mm sand cast iron /PVC`P' or `S' trap, set in cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 stone aggregate) 5.0 Litres capacity white vitreous china low level cistern having all internal fittings, 32mm dia galvanised iron (medium class to IS:1239) flush pipe with fittings & clamps in-cladding necessary supports, C.P. nuts, bolts, unions, washers etc making holes in walls, floors & making good.
Providing & Fixing of concealed in wall flushing cisterns with dual flushing actuator plate ( plastic body in approved finish ), flush stop function noise less float valve and fast filling action with all component parts of high quality complete in all respects.
Providing & Fixing white glazed vitreous China wash basin (under / over the counter) with 32 mm dia C.P brass waste of standard pattern, 32 mm dia C.P cast brass bottle trap and union, 32 mm dia C.P brass pipe to wall and CP wall flange, and rubber acceptors for waste connection, R.S. or C.I. painted brackets bolts, nuts etc. cutting & making good the wall and floor wherever required. Gap shall be filled with silicon sealant whereever required.
Oval wash basin/Round wash Basin
Providing & Fixing of C.P. Brass single lever basin mixer without poping water with 450 mm long copper pipe and brass nuts complete including & making good the walls / Floors wherever required.
Providing & Fixing recessed type stainless steel toilet paper holder of approved makes. Including cutting hole in the masonary/R.C.C wall and making good with cement mortar.
Size 150 mm x 150 mm
Providing & Fixing CP brass coat hooks (double) of approved make. Including providing & fixing C.P brass screws, washers, rawal plug etc.
Providing & Fixing liquid soap dispenser of approved make. Including screws, washers and rawal plug etc.
Providing & Fixing CP brass short body bib cock including, necessary flange, cutting and making good he walls / floors wherever required complete.
Providing & Fixing CP brass long body bib cock including, necessary flange, cutting and making good he walls / floors wherever required complete.
Providing & Fixing 15 mm dia C. P. Brass angle valve with C.P. brass flange, complete inlcuding cutting and making good the Walls / Floors wherever required.
Providing & Fixing CP towel rod with CP brass bracket of approved make fixed to PVC rawl plug with CP brass screws, making holes in walls & making good the same.
Providing & Fixing C.P. brass Ablution health faucet assembly comprising hand held shower with 8 mm dia flexible tube with mounting bracket fixed on wall complete.[FOR EWC]
Providing & Fixing Stainless Steel Grab Bar 600 X 400 mm size fixed to wooden cleats with C.P.Brass screws complete in all respects.
Providing & Fixing hand drier of approved make and colour having twin blower integrated with timer and infrared sensing system automatic which can work 230 volts single phase 50 cycle etc. complete in all respects.
Providing & Fixing white glazed vitreous china large flat back lipped front urinal basin, C.I bracket (white colour painted) 40 mm CP brass domical waste, 40 mm C.P. caste brass bottle trap, CP flush pipe with spreader & other necessary fittings including C.P. brass hexnipple; elbow; unions, washers, cap, C.P. nuts, bolts etc making holes in walls, floors & making good.
Urinal - Flat back lipped frontal.
Providing & Fixing Infra-Red based electronic flushing system operated on 6V DC (4AA) battery for urinals comprising of solenoid valve, concealed built in strainer & flow mechanism piping, flush mounted sensors with all accessories & fittings complete in all respect in fully operational condition etc including cutting and making good the wall where required.
Providing & Fixing white glazed vitreous china urinal partitions of approved make including rawl plugs, screws or any other approved device for Fixing arrangements, making holes in walls, floors & making good.
Size 680 mm x 300 mm.
Providing & Fixing 6 mm thick beveled edge mirror with teak wood beading (Mirror of approved quality and as per specifications) with 6mm thick marine ply wood ground fixed with C.P. brass screws and washers etc. complete.
Size 600x450mm
Providing in position storage type Hot Water electrical horizontal heaters with copper container, insulation, and stove enameled M.S. jacket, thermostatically controlled immersion heater, with pilot lamp, 15/20mm dia inlet with non return valve and 15/20mm dia outlet including making connections complete in all respects. (wall mounted with suitable M.S. bolts and nuts)
Capacity - 20 Lit
Providing and fixing stainless steel sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm
Providing & Fixing Wall Mounted C.P. Brass Sink Mixer single hole tap with swinging costed spout of required size including cuttinig and making good the wall wherever required.
Drainage System (Soil & Waste Pipes ) :
UPVC Pipe & Fittings
SOIL, WASTE, and VENT DRAIN PIPES & FITTINGS:
Providing, Fixing, Testing & Commissioning uPVC SWR pipes (Type-B) for soil, waste and vent conforming to IS 13592 along with all required fittings like tees, bends, cowls, crosses with or without access doors jointed with approved solvent cement fixed to walls and ceilings including angle supports with clamps complete including cutting holes in R.C.C/brick work (slab/beam/wall) and making good the floors, beams and walls with cement mortar where required complete of outer diameter.(Soil/ Waste pipe)
110 mm dia
50 mm dia
Providing and laying cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate, 20 mm down gauge) 75 mm in bed and all around CI/SWR soil & waste pipes under floor, including shuttering etc. complete as required in all respects.
110 mm dia
Providing and Fixing sound insulated Polyproplene piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with 3 layer pipe made of PP-C + PP-MV + PP-C in Blue Ral 5014 (halogen and calcium free) colour, push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 22 dBA as per DIN 4109 at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, density of pipe = 1.25gms/cm3, elongation = 0.05mm/m0K and tensile strength > 24 N/mm2,with all necessary fittings in blue colour, fitted with factory fitted lip ring. - For indirect waste/sinks, wash bassin etc.)
Providing and Fixing uPVC, P or S trap of self cleansing design with / without vent. Arm Setting in cement concrete 1:2:4 mix complete including cost of cutting & making good the Wall / Floors wherever required.
110 mm inlet & 110 mm outlet.
Providing, Fixing, testing and commissioning of uPVC cleanout plug conforming to IS:14735 – 1999 complete with all fitting, accessories and civil works.
110 mm dia.
Providing and Fixing uPVC inlet fittings with maximum 3 inlets 40, 50 or 63 mm OD size (HOPPER) including setting in cement concrete 1:2:4 (1 Cement:2 Coarse sand:4 Stone ballast 20 mm nominal size),cutting and making good the walls and floors.
Providing and Fixing uPVC floor drain including all fitting and accessories fixed in cement mortar complete in all respect.
110 mm OD x 63 mm OD
P/Fixing stainless steel grating with rim of approved design including setting in floor with cement mortar. (For Floor Trap/Floor Drain)
125 mm x 125 mm
100 mm x 100 mm
Providing and fixing straight/offset type Macfit single body push fit type WC Pan Connector with factory supplied spring loaded seal guard with integrated single mould sealing fins made of flexible EVA Body, including bush/adaptor for use with CI Pipe as supplied with Pan Connector (For European water closet) [Make : McAlpine, UK/Equivalent].
Providing, fixing & testing of uPVC pipes (IS : 4985-1983 class-5 10 Kg/cm2 pressure) including injection moulded fittings (heavy duty) (plain or door) e.g. bends, junction, cowls, tees, offsets, access pieces etc. Clamps/Supports jointing with rubber ring/solvent cement joints including cutting chase or holes in walls and floors and making good as required at Site.( For rain water)
Construction of brick masonry inspection Chamber (450x450)mm inside depth upto 600mm in brick work in cement mortar 1:4 mix RCC top slab with 1:2:4 mix foundation concrete in 1:4:8 mix, inside plastering 12mm thick in cement mortar 1:3 mix with flitting coat of neat cement and marking channels complete including cost of manhole frame and Cover of required size of standard quality and carriage of all materials involved complete
Providing and fixing in position polyethylene septic tank type-B (Comfort or equivalent ) having capacity for 20 users, 47"x51"x119" inches in size, including excavation of put as per the size, providing and laying of 150mm thick bed concrete in 1:4:8 mix (1: cement:4 course Sand :8 graded stone agg 20mm nominal size) filling the septic tank with fresh water, connecting the inlet and outlet with the septic tank and filling the dry course of sand and bajre around the septic tank complete Job including carriage of all materials involved
Earthwork in excavation by manual means or mechanical means in trenches/septic tank/soakage pits incl. disposal of excavated earth beyond the site, disposed earth is to be leveled and neatly dressed including dewatering of trenches during excavation ( if required)
Dry random rubble masonry with hard stone in foundation and plinth using quarry stone with bond stones incl. carriages of stones
Providing and fixing water storage tanks with PVC lid having locking arrangement (Triple layer of approved quality (Sintex or equivalent) including making inlet, outlet and overflow connections
WATER SUPPLY SYSTEM (Domestic, Flushing & Hot Water supply system) :
CPVC Pipe Embedded in Wall :(Internal)
Providing, fixing, testing and commissioning of CPVC (Chlorinated Polyvinyle Chloride) pipe as per CTS SDR-11 & fittings such as tees, brass FPT elbows, reducers, male/female male adaptor with brass threads, clamps etc. as per ASTMD-2846, jointing with CPVC solvent cement as per manufacturer recommendations conforming to ASTM-F493. Cutting and making good the walls, floors, R.C.C. work etc. cutting chase and filling the same with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or cement mortar (1 cement : 4 coarse sand) as required (Location : Pipe chase / embedded in wall) .
UPVC High Pressure Water Pipe (Exposed) :
Providing, fixing testing, and commissioning of CPVC (Chlorinated Polyvinyle Chloride) pipe as per CTS SDR-11 & fittings such as tees, brass FPT elbows, reducers, male/female male adaptor with brass threads, clamps etc. as per ASTMD-2846, jointing with CPVC solvent cement as per manufacturer recommendations conforming to ASTM-F493. Steel Structural support as required/directed at Site including all civil work, cutting and making good the walls, floors, R.C.C. work etc.
15 mm dia
20 mm dia
25 mm dia
32 mm dia
40 mm dia
Thermal Insulation on Pipe (Exposed)
Providing & fixing thermal insulation on hot water pipes, a flexible electomeric foam of closed cells structure having thermal conductivity of 0.038 W/M.K at 40o C, water vapour permeability fire propagation including all accessories complete as per specification. All joints shall be sealed with adhesive & cotton tape, shall be applied to give uniform appearance & finished with polyshield protective coating.
18 mm [9 mm thick insulation]
22 mm [9 mm thick insulation]
28 mm [9 mm thick insulation]
35 mm [9 mm thick insulation]
42 mm [9 mm thick insulation]
Providing, fixing, testing & commissioning of forged brass nickle plated lever operated ball valve of full bore with forged brass hard chrome plated ball with min. working pressure of 10 Kg/cm2 Hydraulic test pressure at seat & shell shall be 16 Kg/cm2 . Lever should be anti rust coating, complete in all respects (For Domestic CWS/FWS Application).
15 mm dia
20 mm dia
25 mm dia
32 mm dia
40 mm dia
Pressure Reducing Valve:
Providing and fixing pressure reducing valve with compensation chamber in forged brass body suitably nickle plated, NBR nitrile elastomer diaphragm, EPDM seals and O ring, DZR brass road, stainless steel AISI 303 seal seat, pressure gauge connection FG 1/4" and complete with built-in filter of SS316 having 0.4mm mesh size capable of handling inlet pressure to a maximum of 16 bars and outlet pressure 0.5 to 7 bars adjustable.
40 mm dia
Providing and fixing forged brass auto air vent valve 10 PN rating including all fitting & accessories.
15 mm dia
UPS DISTRIBUTION BOARD: Incomer: One (1) No. 32 A DP MCB . 3 Nos. phase indication lamps and 3 Nos. status indication lamps for ON/OFF/ Trip with control SP MCB. Busbar : 100A TPN Al. Busbar of short circuit withstand capacity 35kA. Busbar shall be insulated with heat shrinkable sleeves and shall be color coded. Outgoing : Each MCB outgoing feeders shall be provided with ON/OFF/Trip indication lamps with back up SP MCBs. 4 Nos. 32A DP MCB . UPS DISTRIBUTION BOARD described as above.
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator)
12 way (4+ 36), Double door, horizontal type
8 way (4+ 24), Double door, horizontal type
6 way (4+ 18), Double door, horizontal type
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
8 way, Double door
12 way, Double door
Supplying and fixing of following rating, 240V/415 V, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
40 amps,4P
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
Single pole
Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.
Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
SUBHEAD-II: WIRING & ACCESSORIES
POINT WIRING
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. - Group C
Supply and wiring for Group control light point / fan point / exhaust fan point with 1.5 sqmm FRLS PVC insulated, copper conductor cable in surface / recessed MS conduit, with flexible conduits & coupler and earthing the point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable etc as required without switch, Socket & Box etc. - Group C
Wiring for power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
Wiring for light plug with 2X2.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 2.5 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. ( light plugs to be used in non residential buildings)
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.
4 x 16 sq. mm + 2 x 6 sq. mm earth wire
2 x 10 sq. mm + 1 x 6 sq. mm earth wire
Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
5/6 amp switch
15/16 amp switch
3 pin 5/6 amp socket
6 pin 15/16 amp socket
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
Supplying and fixing following size / modules, GI box along with modular base & cover plate for modular switches in recess etc as required.
1 or 2 Module (75mm X 75mm)
3 Module (100mm X 75mm)
4 Module (125mm X 75mm)
6 Module (200mm X 75mm)
8 Module (200mmX125mm)
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required
Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.
1 or 2 Module
3 Module
4 Module
6 Module
8 Module
SUBHEAD-III: TELEPHONE & DATA
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
Telephone socket outlet
Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.
Supplying and fixing following modular switch/ socket with modular plate & switch box including connections etc. as required.
Supply, laying, installation, testing and commissioning of Tagblock in wall recessed / surface mounted.
Supply and drawing of cat 6 Data cable in existing conduit as require.
SUBHEAD-IV: LIGHTING FIXTURES
Supply, receiving, storing, handling, assembling in position the following light fixtures including lamps as described below complete with all accessories,hanging rods, control gear as required at site.
22 W LED TUBE Light
30 W LED Down Light
Bulkhead Light
SUBHEAD-IV: EARTHING SYSTEM
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.
Supply, installation, testing and commissioning of following sizes of GI/ Copper strip/wire clamped to walls, cable trays, bus ducts, cables in recess or surface etc for equipment/ System earthing complete as required including inter connection between length at joints, all fixing accessories saddles, clamps, lugs etc and other fixing hardware material as required for proper installation.
G.I. Earthing strip/wire :
25 x 6 mm strip
Copper earthing strip/wire :
25 x 6 mm strip, insulated
UPS SYSTEM:
ONLINE UPS AS PER IEC 62040-3,VFI-SS-111 type
Design, manufacturing, assembly, testing at works, supply, receiving at site, erection, testing and commissioning of true-online double conversion VFI Technology UPS, 1Ph/1Ph. AC input & 1Ph/1Ph AC output UPS system suitable for 240VAC, 50Hz supply, variation +/-1% , PF 0.8 as required as per specification and consisting of following:
IGBT Rectifier Modules to achieve less than 2% Input Current distortion and greater than 0.98 PF at Input at all loads.
Fully microprocessor based with diagnostics capability.
Dual Input (Separate Input for rectifier and separate input for Bypass)
Required quantity and details of UPS are as mentioned below. Location details and mode of operation of UPS shall be as per Annexure-1:-
5 kVA (1Ph output) with30 Minutes Backup
Lift Works:
Supply Installation,Testing & Comsissioning of Passenger Lift. (8 Passenger)
Providing, Installation and testing of four (4) core 185 Sq. mm armoured cable for service lines in walls with necessary plastic/conduit in & under ground with necessary covering conduits including excavating of earth for layying line and dry brick bed under line & reffiling of earth work complete
Supply, Fixing, testing & commissioning of energy saving ceiling fans of approved quality & make 1200mm sweep having rated voltage of 160 to 265 Vac, input power 35W, air delivery 220 M3/min, speed 350 RPM, 2 number ball bearing, 3 number leaves, 5 speeds fine control breeze pattern complete including fixing accesories
Max air exhaust fans high performance air extraction whisper quiet operation 600 Sqm 225mm automatic shutter operation 215mm fan dia 230 - 240 rated voltage 38 watt having Ball bearing motor 50 dsa decibel rating at 3m.
Information dissemination about type and schedule of civil works, utility shifting/damage/emergency repairs, complaint handling and all such issues that affect different stake holders Dissemination modes to include display of banners/notices, distribution of handbills, organization of meetings and other appropriate means at least once in a month for the entire project duration.
Provision of Project Information Board in sheet steel and all supports, including fixing and maintenance during the entire project. Minimum board size should be 3 meters x 2 meters, with necessary information in English and local language written in black paint with white back ground. The board details and the required information will be furnished by the Engineer. The complete design, including logo and information to be displayed shall be approved by the Engineer.
Particulate matters 10 and 2.5 (PM10, PM2.5), sulfur dioxides (SO2), nitrogen dioxide (NO2), and hydrocarbons (HC) Once in 06 months at 2 locations at construction site (for 2 years)
Noise Level in dB(A) Leq Once in 06 months at two locations at construction site (for 2 years)
Providing 2.5 mt. high corrugated GI sheet (min. thickness 0.50 mm) barricading fixed with GI hooks and nuts on frame made of Structural Mild Steel ISA 50 x 50 x 6. Spacing of vertical members shall not be less than 2.5 m (average) and minimum two horizontal ISA 50 x 50 x 6 shall be provided. Rate shall be inclusive of cost of providing all materials and fixing arrangements, including excavation of pits & laying of M-10 Cement Concrete Blocks for Vetical Posts, transportion to site, fixing, backfilling, removal of the complete barricading after construction work is over and rehabilitation of the site etc., with all incidental charges, leads, lifts and all taxes and duties as applicable and as specified by Engineer-in-charge. Material of barricading shall be the property of contractor after completion of the work. Barricading shall be maintained throughout the construction period. It should be installed in a manner so that one cannot crawl underneath it, should be sturdy enough to bear normal wear and tear at the construction site, should not topple off and hurt someone and should be strong enough to withstand the elements, including high wind conditions. Should be fixed between two buildings (A and B) and along the access road.
Safety Signboards, delineators, traffic regulation equipments, flagman, temporary diversions, etc
Minimizing air/dust pollution by providing high dust resistant net of not less than 130 g/m² (weight) in green colour with high tear resistance to be installed on the boundary wall (at least 3 mts. high) and on the barricading (about 1.5 mt. high)
Wet type portable toilet (MS fabricated) 2 seats (1 for men and 1 for women with separate entrances), fitted with 2000 liters capacity overhead tank and 500 liters capacity bottom tank, fitted with Indian type of pot with other facilities such as tap, lighting and ventilation; and sludge tank of capacity 1000L, and stationed at a suitable place in or around 50 metres from work front. Includes cost of water, cost for emptying of bottom tank through mobile suction machine, attendent cost for looking after cleaning and operation of the toilets, all materials and labour charges, all incidental charges, leads, lifts and all taxes as applicable from time to time and as specified by Engineer-in-charge.
Drinking water will be provided from the existing Public Health Engineering(PHE) supply lines of the college without disturbing their supplies as the same is available in sufficient quantity and throughout day and night. water quality testing ( one sample/06 months)
Supply fixing and commisioning of 100 mm dia G.I pipe medium grade "B" class under ground with all fittings such as Sockets, bends, tees and making of connection with main P.H.E water supply line 250/300mm dia pipe including earth work excavation in trenches for pipes and refilling of earth complete after laying of pipe from main road to building edge.
Supply fixing and commissioning of 75 mm dia G.I pipe medium grade "B" class in walls, floors with all fittings such as Sockets, bends, Tees complete including making good the walls.
Supply and fixing of Gate value of Gun metal body with iron wheel complete.
a) 100mm dia
b) 75mm dia
Supply and fixing of fire fighting hose reel of iron (self winding type) with pivot and roller & pipe cover including 50 mm CANVAS hose pipe (30 m length) and hose brass nozzle complete.
Supply, fixing testing & commissioning of Red glass break fire Alarm bell with electric connection complete.
Construction of gate value Chamber 300mm x 300mm internal size of mass concrete walls 200mm thick with concrete floor and heavy duly steel cover & frame (with locking arrangement) complete including plastering.
Providing and fixing of 900mm x 900mm glazed fascade for hose reel & control value with 50mm x 50mm x 2mm. At powder coated Aluminium frame with 5mm thick plate glass front with caustion notice & instruction written on it with red paint.
M M SHAWL ENGINEER AND CONTRACTORS PVT LTD
stage.html
html • 0.03 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 1.56 MB
BOQ_169458.xls
BOQ • 0.43 MB
Download all tender documents and submit your bid