Construction of Panchayat union office building at kadayam block in Tenkasi District under SCPAR 2025-26

Construction of Panchayat Union office building at Kadayam block at Tenkasi District.

Preparatory Works

Clearing jungle including uprooting of trunk vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Earthwork excavation for foundation (for narrow excavation) to full depth as per designed in all soils and sub soils except soft disintegrated rock not requiring blasting and hard rock requiring blasting and bailing water wherever necessary. Refilling the sides of foundation with excavated earth other than sand in layers of well rammed and compacted and depositing the surplus earth in places shown by the departmental officers with an initial lead of 10m and initial lift of 2m and clearing and leveling the site etc. complete complying with standard specification with Refilling.

Providing Pre-constructional anti- termite treatment and creating a chemical barrier to the building by injecting chemical emulsion of required concentrations raft slab and beam, under Cellular raft slab, around the footings, column pits, trenches, pits, wall trenches, back fill, plinth filling, junction of wall and floor, side walls of foundation, external perimeter of building, surrounding of pipes expansion joints, etc. as per IS specification and as per the instructions of chemical manufacturer and all as directed. The treatment shall be carried out strictly in accordance with the technical specification and conforming to IS 6313 (PART-2) or equivalent BS specification.

The chemical to be used as insecticides for the treatment shall be Termite oil 20% (or) 50% EC and the application shall be dilute one part of chemical 20% or 50% EC with 19 or 49 parts of water to get 1% emulsion and strictly in accordance with the manufacturer's specification.( or)2.The chemical to be used as insecticides for the treatment shall be IMIDACLOPRID 30.5% S C and the application shall be applied at 0.075% active ingredients concentration i.e. 2.1ml formulated product diluted 1 lit of water and strictly in accordance with the manufacturer's specification.

Supplying and filling in foundations and basement with filling M- sand in layers not exceeding 15 cm. thick, well watered ,rammed and consolidated etc. complete complying with standard specifications.

Plain Cement Concrete 1 : 4 :8 ( one part of cement, four parts of sand and eight parts of hard broken stone ) using 40 mm gauge hand broken hard broken granite stone jelly complying with standard specifications in foundations and basement.

Refilling the approved good quality earth in plinths, area development etc. wherever specified in layers is not exceeding 200 mm thick, with available earth at site.

Supplying and Filling Gravel:Supplying and filling in 'foundation and basement with filling sand in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc.,complete complying with standard specification.

Supplying and erecting Centering and Shuttering for soffits including necessary supports and strutting up to 3 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification.(Payment for centering shall be given after the concrete is laid).

Footing, Plinth Beam, etc.

Plain surfaces such as roof slab, floor slab, beams, lintels, loft, sill slab, staircase waist, portico slab and other similar works.

Column upto Basement

Square and rectangular columns and small quantities such as sunshades, parapet cum drops, window boxing, fin projections and other similar works.

For circular columns.

Design Mix Concrete

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000, using 20mm and down grade hard broken granite stone jelly for all RCC Items of works with minimum cement content of 350kg/m3 and maximum water cement ratio of 0.50, including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS:9130 to accelerate, rated setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m) 7730kg. of 20mm machine crushed stone jelly and with about (3.3cum) 5156 kg. of 10-12mm machine crused stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with Mechanical vibrators, finishing, curing, etc.,and providing fixtures like fan clamps in the RCC Floor / roof slabs wherever necessary without claiming extra, etc., Complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No Separate payment will be made by the Department for the excess usage of materials).

Foundation & Basement

Ground Floor

First Floor

Terrace Floor

Steel - Fe 500 D

Supply, fabrication and placing of reinforcement steel of high yield strength ribbed bars of various diameters and grade conforming to IS 1786 for reinforced concrete work. The work includes recoiling, straightening, cutting, bending, fabricating, and placing in position, at all levels including lead and lift, according to drawings, specifications etc. complete and supply & use of 18G black annealed binding wire double fold to tie the bars in position and providing precast cement/ PVC cover blocks for main reinforcement to ensure specified cover and complete., including all labor charges etc as directed by departmental officers.

Brick work in following Cement Mortar 1:5 using best quality Country bricks of size 8"3/4 x 41/4" X2 3/4" for foundation and basement including curing etc., complete complying with standard specification. Including scaffolding curing cost of reinforcement etc. all complete as per specifications and drawings as directed by the Engineer in-charge.

Foundation basement

Ground floor

First Floor

Terrace Floor

Brick partition walls of 11.50cm thickness using best quality Country bricks of size 8"3/4 x 41/4" X2 3/4" in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately).

Ground Floor

First Floor

PLASTERING WORK

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [ The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete]. The Putty shoule be got approved by the Executive Engineer before use on work.

Providing & applying 12 mm thick cement plaster in CM 1:5 (1 part of cement: 5 parts of sand) to walls internally in single coat at all levels to correct line and level including chicken wire mesh at all joints of brick and concrete surfaces with minimum overlap of 150 mm in all directions, scaffolding, rounding off or chambering of corners, offsets, fin/ bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labor complete in all respects including all lead, lift and descent and as directed.

Providing & applying 12 mm thick cement plaster in CM 1:5 (1 part of cement: 5 parts of sand) to walls externally in single coat at all levels to correct line and level including scaffolding, rounding off or chambering of corners, offsets, fin/ bands, projections, etc. and cleaning of surface, raking out joints, roughening of surface, chiseling the undulated surface wherever necessary and curing, etc., all materials and labor complete in all respects including all lead, lift and descent and as directed.

FLOORING AND DADOOING

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved color, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same color pigments etc., complete complying with standard specification.(The make and brand of the tiles should be got approved by Executive Engineer before use on works).Basic Cost-Rs.776/sq.m

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works).Basic cost-Rs.464/sq.m

Dadoodling the walls with colored glazed tiles approved size, quality and color set in CM 1:2 - 10 mm thick. And pointed with suitable cement including finishing the joint and pointing flesh with walls and tile surface in all floors at the rate of 0.40 Kg /Sqm etc. complete. Basic cost-Rs.318/sq.m(300 X 450 X 8mm)

Supply and fixing of polished granite slab ,18 mm thick (average), for flooring including fixing in position cutting , chipping the wall, masonry touch up works etc., complete in all respects for all floors as directed by the departmental officers.Basic cost-Rs.1355/sq.m

Supply and fixing of Fine Double side polished granite slab , 20 mm thick (average), for ,urinal including fixing in position cutting ,chipping the wall, masonry touch up works etc., complete in all respects for all floors as directed by the departmental officers. Basic cost-Rs.1850/sq.m

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works).

Providing, fabricating and fixing M.S. grills Windows, and ventilator, gates, ladders, rail pipes, nosing angles, with M.S.lugs in staircase steps etc., made out of M.S rods, flats, angles, pipes, channels etc. including necessary fixtures complete as per drawings and specifications and as directed by the Engineer.

S.S Handrail

Manufacturing,supplying and fixing of stainless steel hand rails for staircase using 50mm dia 304L grade stainless steel pipe of 1.6mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia stainless steel pipe post of 1mm thick as vertical at 900mm centre with 2 Nos of 25mm dia intermediate horizontal stainless steel pipe of 1.6mm thick in between.The vertical pipe has to be welded to the 100 x 100 x 6mm MS base plate encased in the base concrete.The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance,electrical charges,ect.complete.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

UPVC Window supplying and fixing UPVC ( Un-PLASTICIZED Polyvinyl chloride) windows of casement type (open) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforcement with g/1mm 125GSM and 100% corrosion free, the profiles are multi chambered section with wall thick of 2mm. The EPDM rubber (black color) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power points locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed or plain glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss.

The connecting mechanism between sash and outer frame that enables opening of the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames The window should be got approved from the Executive Engineer before use on work.

UPVC VENTILATOR: Supplying and fixing UPVC ( Un-PLASTICIZED Polyvinyl chloride) Louvered Ventilators of from the profile the size of outer frame 60x58mm and shutter profile the size of 60x78mm both profile size of 60x78mm both profiles are reinforced with GI/1MM 125GSM and 100% corrosion free , the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black color) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiation pin headed glass 4mm thick should be fixed to the wall with 100% packing with screws and silicon packing all around the frame. The ventilator should be got approved from the Executive Engineer before use on work.

Solid PVC door shutters Toilet door using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for paneling shall rigidly fixed in position including necessary furniture and fittings. The overall size of styles shall be 50mm x 30mm. The overall size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The overall size of frames shall be 50mm x 45mm, with suitable rebate for housing the shutter.

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

Manufacturing, supplying and fixing of Steel doors with following specification.MS angle of size 40x40x6mm at 3.5 kg/m used for outer frame and MS Angle of size 35x35x5mm at 2.6 Kg/m for the shutter frame. Stiffeners with 32x6mm at 1.5 Kg/m MS Flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame.18 G CR Sheets of best quality is laid as panel in the shutter frames. 18x5mm at 0.70 kg/m MS flat is welded over the 32x6mm at 1.50kg/m MS Flat on the rear side of the door, sandwiching the CR Sheet for rigidity. Additional stiffeners with 18x5mm at 0.7 Kg/m MS flats are provided diagonally on the rear side of the shutter. 300mm length of hinges 2Nos, for shutter is provided.6 Nos. of 250mm length hold fasts 200mm length specified at the ends are welded to the outer frame of the door.Tower bolt 2 Nos. at the top provided.

PAINTING WORK

Painting two coats of synthetic Enamel paint of approved colour and make over one coat of anti corrosive Zinchromite primer over new wood / steel work, suitably prepared for receiving the paint by surface scraping, rubbing applying filler etc. including cost of filler, primer, paint all complete as per drawings and specifications.

Supplying and Painting new plastered surface with two coats of distempering one coat of distemper primer

Supplying and Painting new plastered internal ceiling surface with two coats of distempering one coat of distemper primer

Supplying and painting the walls with one coat of wall primer and two coats of Exterior emulsion (apex or equivalent) as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).

Weathering Course Concrete using best quality broken brick jelly of 20 mm uniform gauge in pure slaked lime ( NO Sand to be used ( over the RCC roof slab in the proportion of brick jelly to lime being 32 : 121/2 by volume laid over in single layer and consolidated to the required slope and finished thickness and beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime, jiggery water etc. complete complying with standard specifications and as directed

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers.

Providing, supply, mixing laying cement plastering 20mm thick with cement mortar 1:4 mixed with water proofing compound Conplast X421IC conforming to IS:2645, @ 150ml per bag of cement (normal setting integral water proofing compound) as specified by the manufacturer over PCC leveling course including preparation of surface, dewatering, finishing, curing etc. all complete as per manufacture's Specification and direction

Paving the floor with best quality Tactile Paver type of new tek BT yellow colour ceramic warning and passage tile for vision Impairment person of size 305 x 305 x 15 of approved quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all approved floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification.(The make and brand of the tiles should be got approved by Executive Engineer before use on works). Epoxy Grouting:Providing and filling the tile joint with Epoxy grout with following specification: surface preparation including cleaning the joint to be free from dust and loose particles.Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the departmental officers.The rate inclusive of cost of materials and labour,etc,complete.

Provision for Plumbing work

SANITARY & CP FITTINGS INSTALLATIONS

Supplying and fixing in position Indian water closet of size 580 x 440mm, glazed earthern ware of approved quality and colour with 'P' trap or 'S' trap confirming to IS:2556-part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One of Lime, Two of Sand, Five of Brick jelly) 100mm thick and by dismantling brick masonry, reinforced finishing to the required slope and including giving necessary connection to PVC soil pipes cement concrete roof / floor slab and making good the disturbed portion to origional condition without leakage etc., complete complying with standard specification and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works)

Supply and fixing in position white European Water Closet of approved make with low level flushing tank 10 litre capacity of best quality and approved make with 100mm P or S trap with double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Executive Engineer before use on works.

Supplying, Installing, Testing and Commisioning the best quality approved make of white glazed floor mounted european water closet with inbuild porcelin cistern 6/3 LPF and wash basin for physically challenge persons (hindware -matrix -70002)with necessary grap railes,hinged railes for support,pan connector bend ,checknut,stopcock etc,. colour solid seat and cover with polythene buffer and flap,CP flanges, CP bolts and nuts,brackets with nuts and boults wall flanges etc, complete ,wash basin shall include 15mm dia CP lever oprareted piller cock with waste coupling , 32mm dia CP bottle trap with extension pipe,supporting bracket with neccesary steel to support the basin 1 No,15mm CP angle valve with 450mm long CP connection pipe and CP wall flanges all of approved make etc., complete complying with standard specification and as directed by the department officers.the quality and mak of EWC & wash basin with full set should be got approved by the Executive Engineer before use on work.

Supplying and fixing Lipped Mouth Porcelain Flat Back Urinal(white colour) of size 26.5x31.5x44cm with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple, and suitable screws, shellac etc., complete. The rate including cost of all materials, labour charges for fixing and transportation etc. completed as directed by Engineer-in-Charge.

Supplying and fixing Wash Hand Basin of size 550 x 400mm with all accessories such as cast Iron Brackets, 32 mm Dia C.P. Waste coupling, Rubber plug and Chain, 32 mm dia ' B ' Class G.I. Waste pipe, 15 mm Dia G.M Wheel valve; 15 mm Dia Nylon connection, 15 mm Dia Brass Nipples, 15 mm C.P. Pillar tap etc.,including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and as directed by the Department officers. (The Wash basin should be got approved by the Executive Engineer before use on works.

Supplying and fixing of CP Two Way Bib Cock with Health Faucet ,wall hook & one metre long flexible tube including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work.

Supplying & fixing in position 15 mm dia brass/ C.P screw down tape (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).(GARDEN&IWC)

Supplying and fixing in position Mirror of size 600x450mm of approved quality and brand with necessary plastic back PVC frame with bottom stand using brass screws rawl plugs for fixing etc complete complying with standard specification and as directed by the Departmental officers. The colour of frame and quality of mirror should be got approved by the Executive Engineer before use on work

Supplying,installing,testing and commissioning of approved make CONCEALED STOP COCK for toilet including neccesary accessories etc,complete,works include making require size curout in wall,and fixing the control box property,redoing the same etc,complete the quality and make of concealed stop cock should be got approved by concern department Engineer before use on work.

Supplying and fixing Brass Chromium Plated Towel Rail 60cm long and 20mm dia with brackets of same materials including cost of teak wood plug & CP screws etc., complying with standard specification and as directed by the Department officers.

Supplying and fixing Brass Chromium Plated Soap Tray of size 150mm x 100mm using rawl plug & brass screws for fixing etc., complete complying with standard specification and as directed by the Engineer Incharge before use on work.

Supplying and fixing CP angle cock with wall flange including cutting and making good the walls wherever required etc., complete complying with standard specification and as directed by the Engineer Incharge before use on work.

SOIL AND WASTE&RAIN WATER PIPE SYSTEM:

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works).

160mm Dia

110mm Dia

75mm Dia

50mm dia

40mm dia

Supplying and fixing PVC cowl of following size to vertical Soil/Waste pipes above terrace level. The rate including cost of all materials, labour charges and transportation etc. completed as directed by Engineer-in-Charge.

PVC Cowl

110mm dia

75mm dia

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Executive Engineer before use on works ).

Supplying & fixing in position 150 X 100 mm square mouth 'P' or 'S' trap stone ware Gully trap 'A' grade with cast iron double gratings of size 150 X 150 mm with C.I. air tight cover with frames of size 300 X 300 mm at bottom & top respectively with necessary earth work excavation, laid over a bed of brick jelly cement concrete 1:3:6, 150 mm thick using 20 mm size broken brick jelly including necessary brick work & plastering, &including dismantling masonry wherever necessary & redoing the damaged portions to the original condition & by using cement concrete 1:3:6 using 20 mm stone jelly for fixing the Gully trap & giving connections to the stone ware sewer line etc., complete, complying with standard specification. (The stone ware gully trap should be got approved by the Executive Engineer before use on works ).

Constructing solid block masonry manhole various size of deep in cement mortar 1:3( 1 Cement: 4 coarse sand ) R.C.C. Raft & top slab with cement concrete 1:2:4, plain cement concrete 1:4:8 mix for base course (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size )above that 150 mm thick RCC M25 raft slab inculding reinforcement 10mm dia 150mm c/c bothways. Plastering inside walls with 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand ) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ), finished with a floating coat of neat cement ,supplying and fixing SFRC manhole cover with farame , PVC foot rest as per detailed drawing etc the quoted rate shall also necessary excavation and back filling etc complete.complete as per standard design : (the chamber and cover should be got approved by the Executive Engineer before use on works) (SOR) Twad(280)

INTERNAL WATER SUPPLY SYSTEM:

Supplying, laying and jointing UPVC pipes SDR 11(having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives and fixing into wall with teak wood plugs, UPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works. Internal toilet

a) 20 mm dia

b) 25 mm dia

c) 32 mm dia

EXTERNAL WATER DISTRUBUTION:(TERRACE,SHAFT, EXTERNAL PIPE)

Supplying, laying, jointing, testing & Commissioning of UPVC Schedule 80 pressure pipes as per ASTM D 1785 with Sch 80 Fittings as per specifications, jointing with hold tite / super tite & tefflon tape and complete with fittings such as sockets, unions, reducers long or short bends, elbows, nipples flanges,checknuts,etc. Pressure testing of piping and back filling of trench complete as required. The quoted rate shall include necessary earth works, fittings like Tees, Bends, Offsets etc., G.I. brackets with pvc coated GI clamps, nuts & bolts, anchor fasteners, grip bolts, GI threaded, rods, etc., complete for external pipes. (For under ground or above ground external water supply piping.) Vertical & External

a) 20 mm dia

b) 25 mm dia

c) 32 mm dia

d) 40 mm dia

e) 50 mm dia

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

a) 20 mm dia

b) 25 mm dia

c) 32 mm dia

d) 40 mm dia

f) 50 mm dia

Supplying and Erection and construction of sewer chambers of required internal dimensions 600x600 upto 0.6 mtr.depth with 230mm brick masonry in C.M.1:5 thk of masonry over bed of 1:2:4 R.C.C. 200 mm thk bove 100 mm thk P.C.C.1;3:6 Cement concrete foundations over M.Sand bed of 100mm thk channelling in 1;2:4 cement concrete, plastering in 1:3 cement mortar for internal and external surface finished with floating coat of neat cement, the work including excavation for required depth of gully trap and refilling and making good in the surface with SFRC cover and frame 600x600mm (clear opening) complete complying with standard specifications etc.,

Supply ,erection and testing & commisioning of 2HP Mono pump set in the capacity of 6000 LPH @ 300Ft, max. total head of 350 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge. ( Sump to OHT transfer pump)(1Working+1 Standby)

Manhole Cover

Supplying and fixing Ductile Iron manhole cover with frame as per approved make ,cover weight and being size mentioned below and specified size in the drawing etc., including painting with two coats of anticorrosive paint over a coat of primer etc., fixing locking arrangements, fixing Man-hole over, grouting the anchors with CC 1:2:4 (one cement,two fine aggregate and four coarse aggregate), as complete in all respects complying with relevant standard specifications and as directed by the Client / Engineer-in-charge.Size:600x600mm

Recharge well

Construction of Rain water Recharge well (1500mm dia) as per consultant drawing with necessary connections, Earth work - digging the well for recharge well. supply and installation of Reinforced concrete Rings - 5 feet OD & 1 feet Height, 50 MM Thick - 10 no's. supply and installation of Reinforced concrete slab- 5 feet in dia, 200 mm thick, and 25 mm perforated - 8 mm mild steel rods used for reinforcement -1" Perforated - 1no's. supply and installation of Reinforced concrete closing slab - 3 feet in dia OD, 75 mm thick, 8 mm mild steel rods used for reinforcement with 600mm x 600mm Square FRP/Plastic manhole cover - 1no's. supply and installation of MS grating - 6*6inch square - 2no's Filtration Media Installation For recharge Well Unit: 40 mm crushed stones - 0.12cum, 20 mm crushed stones - 0.12cum, Brick Bats - 0.12cum, Mixture of Brick Bats and Gravels for filling the gap between excavated earth and RCC rings- 1.6cum Shifting of excavated earth to the approved / authorised dumping yard as directed by the authorities / Site in charge. supply and installation of `V' WIRE SCREEN - 0.75 mm Slots. SS-304 Material - 0.5 mtrs Height - 6 " diameter - 2no's Drilling a bore well - 200mm dia by high speed compressor- 4MTRS. supply and installation of 110mm PVC PIPE PN-6 - 4 rmtr, 110mm PVC PIPE PN-6 Perforated with 10 mm Zigzag holes to easy percolate the water - 4 rmtr, 12mm Gravel Packing between bore well hole and PVC pipe and Inserting into the Bore Well- 4 mtrs. supply and installation of - 180GSM Gio-fabric sheet to cover V-Wire screen, Shifting of excavated earth upto 1000mtrs as directed by site in charge. (the well sholud be got approved by the Executive Engineer before use on works)

Size - 1500mm diameter, 4.0 mtr depth and 200mm dia bore upto 4 rmtr.

PVC Water Tank

Providing PVC water tank including all cost of materials etc... (M-0540)

Provision for Incinerator

Laddies Toilet (GF & FF )

Provision for Electrical work

Internal Electrification

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )

Wiring, testing and commissioning of 2Rx1.5 +1Rx1sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe with 2 mm thick, ISI marked concealed in ceiling with PVC accessories for additional light (Secondary)

Wiring with 3 x 1.5 sq. mm PVC insulated single core unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with module GI switch box in flush with wall with 6A two-way module switch with module front plate with continuous earth wire connection of 1.5 sq. mm copper wire and making good of the concealed portion with suitable colour for concealed PVC pipe staircase light point (higher end).

Lift Shaft Wiring : Wiring, Connecting, Testing & Commissioning for lift well light point and 6Amps power socket outlet with 2 x 2.5 sqmm FRLS PVC insulated stranded copper conductor of 1100V grade along with 1 x 2.5 sqmm FRLS PVC insulated standed copper conductor cable as earth wire in MS conduit including providing and fixing switch box, 2 Nos. of 5A single way module switch (for controlling light point and socket Outlet ) for each floor of the lift well , with bulkhead lamp 1 No. 5A 5 Pin shuttered socket outlet with flush type switch for each floor of the lift well and making necessary connections complete etc.

Supply and fixing of 1 no.6A two module 3 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 2nos.6A two module 3 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 2 nos.6A two module 3 pin socket , 2 nos. 6A one module switch on suitable module surface mounting Box ( Plastic ) with module cover plate (plastic) on wall with connections. Higher End

Supply and fixing of 3nos.6A two module 3 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 20A Flush type Wall Socket 32A DP MCB complete set for AC Plug in flush with wall with earth connection (For AC Plug)

Run of Mains

Supply and run of 4x6sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V on 7/20 GI bearer wire for service connection mains

Supply and run of 3 of 2.5 sq. mm PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 2.5 sq. mm copper wire and making good of the concealed portion.

Supply and Run of 3 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed position. ( Rawpower 6 / 16Amps Socket & Split Ac unit Point Wiring). (Split Ac unit Point Wiring-2TR UNIT.)

Supply, run, testing and commissioning of 3CX2.5sqmm PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in existing floor raceways/PVC rigid pipe with 2 mm thick, ISI marked concealed in floor/wall and

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 375mm (15") sweep (light duty) AC exhaust fan complete without provision of holes in the wall

Supply and fixing of 7 segment 6 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.

Supply and fixing of 7 segment 8 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 24 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 40A 4P MCB Isolator as incoming and 4 nos. 32A TP MCB as outgoing in flush with wall with earth connection only.(MLDB)

ADD 4NOS 40A TP MCB

Lighting

Supplyandfixingofsingleboxtype4'36WfluorescentfittingcompletewithelectronicballastwithTWroundblocksonwall or ceiling with flu tube with PVC unsheathed FRLS Copper leads from terminals to the fitting

Supply and fixing of single box type 4'22W LED fitting complete with built in driver and clamps to fix on wall or ceiling with PVC unsheathed Copper leads from terminals to the fitting

Supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of fancy glass shade and 7W / 9W LED bulb

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting.

Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED Bulb

supply and fixing of 30W LED street light fitting with LED (Higher end) with 25 mm dia. GI pipe (class B) with 1 no. 25 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .

Supply and laying of following PVC LTUG armoured cable in a trench/Tray with suitable cable tie tag etc as required.

3.5CX70sqmm PVC armoured LTUG Cable

3.5CX25sqmm PVC armoured LTUG Cable

Supply and fixing of double compression brass cable gland for following Aluminium conductor XLPE insulated armoured cable of 1100 V grade with earth connection.

3.5CX70sqmm Al. armoured LTUG Cable

3.5CX25sqmm Al. armoured LTUG Cable

Supply and installation of following size of GI Ladder / preforated cable tray including pre fabricated horizontal and vertical bends, reduces, tees, cross members with 300 mm spacing and other accessories as required and duly suspended from the ceiling, wall with MS angles, channels, suspenders, including painting, anchor fasteners, civil works etc., as required as per specification.

150X50mm Perforated Tray

Earthing

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class'B' GI pipe of dia not less than 40mm with copper earth plate of size125mmx50mmx6mm with necessary funne lingarrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply, fabrication, of GI /Copper earth flat of following size in provided trench, clamping in wall, ceiling, with suitable Clamps/ saddles, connecting the joints through bracing / welding covering with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive

25mm x 6mm GI Flat

25mm x 3mm GI Flat

25mm x 3mm copper Flat

No8 SWG GI

LT PANELS

LT Metering Panel -Supply and fixng of TNEB meter board suitable for 3 phase 100A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1-1/2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 100A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete

Main Panel - Supply, Installation, Testing and Commissioning of CPRI approved make of panel, cubicle type, Free standing, floor mounted, single front, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, Powder coated, indoor type dust and vermin proof, hinged lockable doors, cluster LED type indicators, in the incoming feeders, complete with electrolytic grade aluminium bus bars, internal wiring, colour coding, ferrules, cable gland plates, Aluminium earth bus for the entire length of the panel with bonding to earth, Panel mounting MS Channels, fasteners, etc., including all associated control wiring. The panel details as follows:-

Safety Accessories

2m x 1m Rubber Mat suitable for 11 KV installation confirming to IS-(1SET -5 NO)

First Aid Box complete with all First Aid Medicines

Shock Treatment Chart fixed in glass frame

Metallic Danger Board as required by the Electrical Authorities

Fire Extinguisher Co2, 4.5 kg. confirming to TAC Norms

Provision for Sump Work

Earthwork for foundations and depositing on bank with initial lead of 10 Mt. and initial lift of 2 Mt. in sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam and ordinary soil including excavated earth.

Supplying and filling in foundation and basement with m sand in layers of not more than 10cm thick well watered, rammed and consolidated etc., complete as per standard specification.

Laying the Plain Cement concrete 1:4:8(One cement four sand and eight broken Machine crushed stone jelly) using HBG Machine creased Machine crushed stone jelly of size 40mm gauge for founding and basement including de- watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers. The rates inclusive of Centering , shuttering, strutting, propping,removal of form work if it is required and all leads ,lifts and curing etc..

Supplying and Erecting centering for sides and soffits including necessary supports and strutting up to 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification. (Payment for centering shall be given after the concrete is laid)

Providing and laying in position machine batched,machine mixed and machine vibrated design mix cement concrete of M25 grade for reinforced cement cement ratio with plasticiser using 20mm and down concrete structural elements under controlled water graded machine briken grnite stone jelly excluding the cost of centering and shuttering and reinforcement but including curing, fixing, fan clamps etc., as per standard specification and as directed by the depart- mental officers comple.-1m3

Supply, fabrication and placing of reinforcement steel of high yield strength ribbed bars of various diameters and grade conforming to IS 1786 for reinforced concrete work. The work includes recoiling, straightening, cutting, bending, fabricating, and placing in position, at all levels including lead and lift, according to drawings, specifications etc. complete and supply & use of 18G black annealed binding wire double fold to tie the bars in position and providing precast cement/ PVC cover blocks for main reinforcement to ensure specified cover and complete., including all labor charges etc as directed by departmental officers.

Providing, supply, mixing laying cement plastering 20mm thick with cement mortar 1:4 mixed with water proofing compound Conplast X421IC conforming to IS:2645, @ 150ml per bag of cement (normal setting integral water proofing compound) as specified by the manufacturer over PCC leveling course including preparation of surface, dewatering, finishing, curing etc. all complete as per manufacture's Specification and direction

Supplying, laying and fixing in position ceramic tiles of approved size , quality and colour set k in CM 1:3 - 20 mm thk. Including cutting the tiles to the required size with special cutter where ever necessary and pointing the joints with coloured cement using 0.40 Kg / Sqm including finishing the flooring and pointing the joints flesh with tile surface etc.complete.Basic cost-Rs.464/sq.m

Supplying and fixing in position C.I.Manhole covers (heavy duty) of various sizes of best approved quality and as per standard specificationsetc.,complete.0.6X0.6M Size etc., complete.

PVC mould CI steps for sump

Provision for Septic Tank

Earthwork for foundations and depositing on bank with initial lead of 10 Mt. and initial lift of 2 Mt. in sand, silt or other loose soil, wet sand or silt not under water, light black cotton soil, sandy loam and ordinary soil including excavated earth.

Supplying and filling in foundation and basement with m sand in layers of not more than 10cm thick well watered, rammed and consolidated etc., complete as per standard specification.

Laying the Plain Cement concrete 1:4:8(One cement four sand and eight broken Machine crushed stone jelly) using HBG Machine creased Machine crushed stone jelly of size 40mm gauge for founding and basement including de- watering if found necessary and laid in layers of not more than 15cms thick etc., complete complying with standard specification and as directed by the departmental officers. The rates inclusive of Centering , shuttering, strutting, propping,removal of form work if it is required and all leads ,lifts and curing etc..

Supplying and Erecting centering for sides and soffits including necessary supports and strutting up to 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at about 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specification. (Payment for centering shall be given after the concrete is laid)

Providing and laying in position machine batched,machine mixed and machine vibrated design mix cement concrete of M25 grade for reinforced cement cement ratio with plasticiser using 20mm and down concrete structural elements under controlled water graded machine briken grnite stone jelly excluding the cost of centering and shuttering and reinforcement but including curing, fixing, fan clamps etc., as per standard specification and as directed by the depart- mental officers comple.-1m3

Supply, fabrication and placing of reinforcement steel of high yield strength ribbed bars of various diameters and grade conforming to IS 1786 for reinforced concrete work. The work includes recoiling, straightening, cutting, bending, fabricating, and placing in position, at all levels including lead and lift, according to drawings, specifications etc. complete and supply & use of 18G black annealed binding wire double fold to tie the bars in position and providing precast cement/ PVC cover blocks for main reinforcement to ensure specified cover and complete., including all labor charges etc as directed by departmental officers.

Providing, supply, mixing laying cement plastering 20mm thick with cement mortar 1:4 mixed with water proofing compound Conplast X421IC conforming to IS:2645, @ 150ml per bag of cement (normal setting integral water proofing compound) as specified by the manufacturer over PCC leveling course including preparation of surface, dewatering, finishing, curing etc. all complete as per manufacture's Specification and direction

Supplying, laying and fixing in position ceramic tiles of approved size , quality and colour set k in CM 1:3 - 20 mm thk. Including cutting the tiles to the required size with special cutter where ever necessary and pointing the joints with coloured cement using 0.40 Kg / Sqm including finishing the flooring and pointing the joints flesh with tile surface etc.complete.Basic cost-Rs.464/sq.m

Supplying and fixing in position C.I.Manhole covers (heavy duty) of various sizes of best approved quality and as per standard specificationsetc.,complete.0.6X0.6M Size etc., complete.

PVC mould CI steps for sump

Provision for Furniture Arrangements

BDO Table & Engineer Room : The Main Table of Size : 1500mm (L) x 600mm (D) x 750mm (H) and side table of size 900mm x 450mm x 750mm (H) and back credenza of size 1800mm x 450mm x 750mm(H) The Table top made out of 25mm thick particle board and 0.6mm decorative laminate finish with postformed finish. And back credenza having storage made out of 18mm thick pre laminate board duly edge banded with 2mm thick PVC edge beeding swing type shutters and lock and key arrangments. Having a mobile pedestal of size 400x 450x 640mm

Deputy BDO Overseer & L.F Audit Table : The Main Table of Size : 1600mm (L) x 600mm (D) x 750mm (H) and having side table cum storage unit of size 900mm x 450mm x 750mm (H) The side table having a two drawer on top bottom with swing type shutters with lock and key arrangements. The Table top made out of 25mm thick particle board and 0.6mm decorative laminate finish with postformed finish.

Modular Workstation: ‐ 75mm thick : Fabricated out of exclusive Aluminum sections with the following Specifications, (a) All the aluminum sections will be of 1.8 mm to 2 mm thick i.e., depends on the load bearing requirement. (b) The top cover & end cover will be of 75 mm breadth. (c) The electrical raceway cover will be of 100 mm width & 9 mm thick pre laminated / laminated particle board. (d) The tiles will be provided on both sides of the frame are fabricated out of 9 mm thick pre laminated board for tiles & MDF board for white marker board & Magnetic fabric board. (e) The two way, three way & Four way pillars will be fabricated out of 2 mm thick, 75 mm, Square Aluminum sections. (f) All the frames will be connected using bolt & nuts. (g) All the Aluminum sections will be duly powder coated in approved shade after necessary treatment. Table Top and Divder Pannel made of 25 mm thick edge banded with 2mm thick PVC Edge Beeding of Size 1100mm X 750mm x 1200mm (H) . having a mobile pedestal and key board tray

Slotted angle rack of size 1000 X 750 xX 2400 mm (H) 8 shelevs making 7 compartment The angle made of 80 x 40 x 2.5mm thick and panel made of 16SWG with bottom 2 nos horizontal strip .These racks are made from heavy duty slotted angle rack with necessary dipped paint finish and Shelves are 18 SWG made of multiple bends.Right angles are obtained by the use of corner brackets. The racks are covered with 0.8mm thick gladding sheet covered by three sides

Executive Chair Model Jupiter High Back for BDO Table & Engineer Room . The chair are Glass filled nylon base with twin wheel nylon castors and 120mm Gaslight for seat height adjustment. Synchronised multi‐function mechaism.Glass filled nylon backrest with Korean mesh. Seat upholstered with PU module foam and approved fabric. Tested as per ANSI/BIFMA standards. 4D swivel and height adjustable armrest with PU pad

Dynamic Medium Back Chair for Deputy BDO Overseer & L.F Audit : Glass filled nylon base ,Gaslift,twin wheel nylon castors , T Type adjustable PU armrest .back :ABS with mesh upholstery Synchro tilt mechanism , inbuilt lumbar support,seat PU moulded cushion twin wheel nylon castors and 120mm Gaslight for seat height adjustment. Synchronised multi‐function mechaism.Glass filled nylon backrest with Korean mesh. Seat upholstered with PU module foam and approved fabric. Tested as per ANSI/BIFMA standards. 4D swivel and height adjustable armrest with PU pad

BDO Table & Chairman Room : The Main Table of Size : 1500mm (L) x 600mm (D) x 750mm (H) and side table of size 900mm x 450mm x 750mm (H) and back credenza of size 1800mm x 450mm x 750mm(H) The Table top made out of 25mm thick particle board and 0.6mm decorative laminate finish with postformed finish. And back credenza having storage made out of 18mm thick pre laminate board duly edge banded with 2mm thick PVC edge beeding swing type shutters and lock and key arrangments. Having a mobile pedestal of size 400x 450x 640mm

Deputy BDO Overseer & L.F Audit Table : The Main Table of Size : 1600mm (L) x 600mm (D) x 750mm (H) and having side table cum storage unit of size 900mm x 450mm x 750mm (H) The side table having a two drawer on top bottom with swing type shutters with lock and key arrangements. The Table top made out of 25mm thick particle board and 0.6mm decorative laminate finish with postformed finish.

Modular Workstation for Section Office: ‐ 75mm thick : Fabricated out of exclusive Aluminum sections with the following Specifications, (a) All the aluminum sections will be of 1.8 mm to 2 mm thick i.e., depends on the load bearing requirement. (b) The top cover & end cover will be of 75 mm breadth. (c) The electrical raceway cover will be of 100 mm width & 9 mm thick pre laminated / laminated particle board. (d) The tiles will be provided on both sides of the frame are fabricated out of 9 mm thick pre laminated board for tiles & MDF board for white marker board & Magnetic fabric board. (e) The two way, three way & Four way pillars will be fabricated out of 2 mm thick, 75 mm, Square Aluminum sections. (f) All the frames will be connected using bolt & nuts. (g) All the Aluminum sections will be duly powder coated in approved shade after necessary treatment. Table Top and Divder Pannel made of 25 mm thick edge banded with 2mm thick PVC Edge Beeding of Size 1100mm X 750mm x 1200mm (H) . having a mobile pedestal and key board tray

Slotted angle rack of size 1000 X 750 xX 2400 mm (H) 8 shelevs making 7 compartment The angle made of 80 x 40 x 2.5mm thick and panel made of 16SWG with bottom 2 nos horizontal strip .These racks are made from heavy duty slotted angle rack with necessary dipped paint finish and Shelves are 18 SWG made of multiple bends.Right angles are obtained by the use of corner brackets. The racks are covered with 0.8mm thick gladding sheet covered by three sides

Drawing Room Meeting Table of size 3300 x 1400 x 750mm,The table made out of 25mm thick pre laminated particle board duly edge banded with 2mm PVC edge beeding having a one no pop up box without socket(Ground Floor and First Floor)

Executive Chair Model Jupiter High Back for BDO Table & Engineer Room . The chair are Glass filled nylon base with twin wheel nylon castors and 120mm Gaslight for seat height adjustment. Synchronised multi‐function mechaism.Glass filled nylon backrest with Korean mesh. Seat upholstered with PU module foam and approved fabric. Tested as per ANSI/BIFMA standards. 4D swivel and height adjustable armrest with PU pad

Dynamic Medium Back Chair for Section Office : Glass filled nylon base ,Gaslift,twin wheel nylon castors , T Type adjustable PU armrest .back :ABS with mesh upholstery Synchro tilt mechanism , inbuilt lumbar support,seat PU moulded cushion twin wheel nylon castors and 120mm Gaslight for seat height adjustment. Synchronised multi‐function mechaism.Glass filled nylon backrest with Korean mesh. Seat upholstered with PU module foam and approved fabric. Tested as per ANSI/BIFMA standards. 4D swivel and height adjustable armrest with PU pad

Supply and Fixing Wooden Partition of Aluminium Natural colour matt finish extruded box section Frame on 12mm thick Plywood with lamination on both side with 63.50mmx38.10mmx1.41mm at 0.818 Kg/m extruded box section at bottom, and Horizontal members on edges and vertical members are spaced at 60cm center to center and required height from floor level with necessary aluminium clips of size 19mmx17.30mmx0.90mm at 0.124kg/m, L angles, Screws etc., The aluminium surface is to be anodized with matt finish under electrically controlled condition in accordance with ISI1868/1962 specification for an average anodic film thickness. The rate is inclusive of cost of materials, conveyance scaffolding if any required etc. and necessary dismantling making holes in RCC brick masonry wherever with necessary with power drill to the extent required and made good to the original condition after fixing the partition as directed by the departmental officers. All materials should be got approved by the Executive Engineers before fixing in positions and complying with relevant standard specification, as directed by the Engineer-in-charge.

Providing & fixing Teakwood Frame 3"x2"With 30mm thick solid core flush with 85 x 15mm beech wood jamb alround and 12 x 12mm button beading fixed with 1 mm laminate (dark for bands and light for body) on both sides and 8mm clear float glass with etching design as directed with 50 x 15mm beech wood jamb alround the glass opening and 12 x 12mm beech wood beading for fixing of glass on both sides including necessary hardware viz., door stopper, door closure, door set lock (Godrej etc.,)handles, brass hinges of approved make & equality meala mine spray polish finish to all beech wood members etc., complete as directed. including cost of materials, labour charges, transportation charges etc all complete in all respects complying with relevant standard specifications and as directed by the departmental officers.

Provision for Teak Wood Main Door

Provision for Lift Arrangements

Passenger Lift MRL, Speed 1.5 m/s with Stainless Steel Panels, Disable friendly, microprocessor based controller, VVVF drive, Fire rated doors and ARD- 8 Persons

Lift Shaft Wiring : Wiring, Connecting, Testing & Commissioning for lift well light point and 6Amps power socket outlet with 2 x 2.5 sqmm FRLS PVC insulated stranded copper conductor of 1100V grade along with 1 x 2.5 sqmm FRLS PVC insulated standed copper conductor cable as earth wire in MS conduit including providing and fixing switch box, 2 Nos. of 5A single way module switch (for controlling light point and socket Outlet ) for each floor of the lift well , with bulkhead lamp 1 No. 5A 5 Pin shuttered socket outlet with flush type switch for each floor of the lift well and making necessary connections complete etc.

Supply and Installation of 20 Amps DP Switch In Enclosure for Lift Car Lighting And Lift Pit Lighting

63A TPN MCCB for Lift Motor

4 core 10 sqmm armoured PVC LTUG copper cable for Lift Motor

Earthing

Earthing as per the ISI specification with an earthelectrode of 2.10metre Class'B' GI pipe of dia not less than 40mm with copper earth plate of size125mmx50mmx6mm with necessary funneling arrangements with necessary masonrywork and with 38mm RCC cover slab for the brick masonry

Supply, fabrication, of GI /Copper earth flat of following size in provided trench, clamping in wall, ceiling, with suitable Clamps/ saddles, connecting the joints through bracing / welding covering with bitumen paint including accessories wooden plugs, screws, fastener etc., all inclusive

25mm x 3mm GI Flat

Supply and laying of 2 core 1.5 sq.mm. armoured copper cable for control wiring to the Terrace Pump Motor with runs of 8 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.

Construction of Compound Wall at Union Office

Earthwork excavation and depositing on bank with an intial lesd & lift in hard stiff clay, gravelly soil, shales, murrams earth mixed soil as per SS 20 B for foundation

Cement concrete in 1:4:8 mix using 40 mm metal used for foundation including cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete.

Supply and erection for Centring Charges for column including all labour charges etc.,

Column Below GL

column above GL

M25 Standard mix including cost and conveyance and all other labour charges etc.,

Brick work in cement mortar 1:5 mix using country bricks including cost and conveyance of all materials to site and all labour charges etc complete

Supply & Fabrication of Steel including cost & conveyance and labour charges for cutting & Bending & Placing in position etc complete

Plastering with CM 1:5 mix using 12 mm thick including cost & conveyance and labour charges etc complete.

Painting Two coat approved Exterior Emulsion over the plastered surface including cost and all other charges etc.,

Providing Paver Block @ Union Office Building

Earthwork excavation and depositing on bank with an intial lesd & lift in hard stiff clay, gravelly soil, shales, murrams earth mixed soil as per SS 20 B for foundation

Cement concrete in 1:4:8 mix using 40 mm metal used for foundation including cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete.

Supply & Erection of centring for sides using country wood planks including cost & conveyance and labour charges etc complete.

Cement concrete in 1:2:4 mix using 20 mm metal used for foundation including cost & conveyance of all materials to site and all labour charges for curing, compacting etc., complete.

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401

Providing and Laying of Interlocking Concrete Block (Surface Textured) Pavements having thickness 80mm and compacted over a thin bedding M.Sand layer of 30 mm thickness and joints shall be filled by fine M.Sand of specified grading as per table 1500.6 of Specification of Rural roads-2014 and Technical specification clause 1504.

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}