Interior Furnishing Works associated with Civil, Furniture, Electromechanical, Airconditioning etc., at SEBI proposed local office in Chandigarh

CIVIL, INTERIOR, PLUMBING AND MODULAR FURNITURE WORKS

INTERNAL ELECTRICAL AND ALLIED WORKS

HVAC AND ALLIED WORKS

FIRE FIGHTING WORKS

AUDIO-VIDEO AND ALLIED WORKS

ITEM DESCRIPTION

DEMOLISHING AND DISMANTLING WORKS

CORE CUTTING

MASONRY WORK, PLASTERING & PAINTING

WOODWORKS, WALL LINING, CARPENTRY WORKS

FLOORING & DADO WORKS

WATER PROOFING WORK

FALSE CEILING

PARTITION WORKS

MISCELLANEOUS WORKS

CUSTOMIZE FURNITURE

CIVIL & INTERIOR TOTAL

SANITARY & PLUMBING

MODULAR FURNITURE

Description

CIVIL AND INTERIOR FURNISHING WORKS

DEMOLISHING AND DISMANTLING WORKS

Removal of all types of Flooring, such as vitrified tile, marble, granite etc., including the PCC bedding on the floor upto RCC slab level using manual / mechanical means as instructed including all types of bedding and trunking ducts. Only the plan area would be measured for payment (all measurements for a particular area would be measured only once).

Removal of all types of Flooring, such as vitrified tile, marble, granite etc., including the PCC bedding on the floor upto RCC slab level using manual / mechanical means as instructed including all types of bedding and filling like brickbat coba and so on in toilets sunken portions. No extra payment towards removal of brickbat coba/double tile flooring etc., over and above the flooring measurement shall be paid. Only the plan area would be measured for payment (all measurements for a particular area would be measured only once).

Dismantling of Wall tiles/ Granite/ Window sill/ Door Jamb lining or any other type of dado including backing plaster etc., complete as per direction of Engineer-in-charge.

All types of brick work, block work, R.C.C., P.C.C. walls including plaster, dado including concealed conduits, wiring, electrical boxes etc., complete as per direction of Engineer-in-charge.

Dismantling of all plumbing fixtures and fittings of the existing toilets(Ladies + Gents), Pantry including wash basin, doors, urinal, W.C., etc., complete as per direction of Engineer-in-charge.

Dismantling of all types of electrical fixtures, switch boards, switches, fans, light fixtures, ducting, Raceway, Exhaust fans, Distribution board, Panel, conduits, junction boxes, speakers, wiring existing in the premises including toilet blocks etc., complete as per direction of Engineer-in-charge.

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :

Of area 3 sq. metres and below

Of area beyond 3 sq. metres

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :

Up to 10 mm thick

Thickness above 10 mm up to 25 mm

Dismantling cement asbestos or other hard board ceiling or partition walls in MS/Aluminium/wood work frames including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

CORE CUTTING

MASONRY WORK, PLASTERING & PAINTING

PCC M-10 Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. Note : 1) Excess/less cement used than specified in this item is payable/ recoverable separately. All works above plinth and upto floor V level : M-10 grade plain cement concrete (cement content considered @ 220 kg/cum)

RCC CEMENT CONCRETE- 1:1.5:3 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

CENTERING & SHUTTERING Centering and shuttering including strutting, propping etc. and removal of form for

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

STEEL REINFORCEMENT BARS Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

HALF BRICK WALL Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth upto floor V level.

Cement mortar 1:4 (1 cement :4 coarse sand)

FULL BRICK WALL Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure including scaffolding: Cement mortar 1:6 (1 cement : 6 coarse sand)

12 MM THICK PLASTER Plastering with 12 mm cement plaster over existing brick work of mix : 1:6 (1 cement: 6 fine sand), including necessary scaffolding etc. complete as per directions of Engineer-in-charge.

15 MM THICK PLASTER Plastering with 15 mm cement plaster on the rough side of single or half brick wall of mix :1:6 (1 cement: 6 fine sand), cost to including necessary scaffolding etc. complete as per directions of Engineer-in-charge.

PUTTY Providing and applying white cement based putty of average thickness 3mm of approved brand and manufacturer over the plastered wall surface to prepare the surface even and smooth complete.

ENAMEL PAINT Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

EMULSION PAINT Wall painting with Apcolite premium emulsion paint matt finish of Asian Paints or equivalent brand and manufacture to give an even shade including over an under coat of approved primer complete as per directions of EIC/Architect.

Two Coats

ACRYLIC PAINT Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

PU PAINT Spray painting using 2 component PU Paint to give a uniform finish. Rate to include priming coat on base surface,sanding the base surface complete as per directions of Engineer in charge

WOODWORKS, WALL LINING, CARPENTRY WORKS

WOOD WORK IN FRAMES Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately)

Second class teak wood

FLUSH DOOR SHUTTER Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters

35 mm thick shutter

12MM PLY Providing and fixing 12 mm thk BWP grade (IS710) plain plywood with necessary screws/nuts & bolts/ nails fixed on wooden/aluminium frame work, complete as per direction of Engineer-in- charge (Frame work shall be paid for separately).

12MM FLEXIBLE PLY Providing and fixing 12 mm thk flexible plywood with necessary screws/nuts & bolts/ nails fixed on wooden/aluminium frame work, complete as per direction of Engineer-in- charge (Frame work shall be paid for separately).

12 MM THICK MDF BOARD Provind & Installing laser cut MDF Panel make out of 12mm thick MDF board as per design fixed on existing plywood panelling

SS HINGES Providing & Fixing 5 Knuckle, 2 Ball bearing butt hinges size 4" x 3" x 3mm with Non-Removable Pin, Material: SS 304, Finish: Satin Stainless Steel (SSS). Suitable for Wooden door weight up to 120kgs, Grade 13, Template Drilled. Approved to EN 1935, Fire-rated, Square Corners, Durability - 200,000 Cycles, Corrosion Resistance - Very High Dormakaba 3043 NRP or equivalent,

SS H HANDLE Providing & Fixing pull Handle back to back with 350mm CTC, adjustable fixing for glass, wood and metal doors in satin stainless steel. The pull handles should have supporting washer with raised bevelling on the outer surface. Length =450mm, 25mm dia, -SS304, Dormakaba TGDI-H 450 or equivalent

MORTICE LOCK Providing & Fixing Mortice dead lock narrow stile with 25mm backset, 24mm square forend, prepared for euro profile cylinder including strike plate in satin stainless steel as per EN 12209, Durability - 200,000 Cycles, Load on Latch Bolt - 120N , Door mass - 200 kg, Corrosive resistance - Very High ( - 20 C to +80 C) , dormakaba DEC 6 Plus 60, 6 pin Euro profile cylinder with inline brass keys. Master keyed system included as per client requirement. External & Internal key operation. Length: 60mm Make - Dormakaba 378a or equivalent

DOOR STOPPER Providing & Fixing floor stop half dome with 45mm dia with fixing accessories, in satin Chrome, Make - Dormakaba or equivalent

TOWER BOLT Providng & Fixing surface Mounted Tower Bolt 8” high Make - Dormakaba or equivalent

TOWER BOLT Providng & Fixing surface Mounted Tower Bolt 10” high Make - Dormakaba or equivalent

UPVC - FIXED WINDOWS Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed window / door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge including the cost of 8mm thick toughened Single glass panes and silicon sealent. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Fixed Windows/ ventilators with mullion transomusing R4 series with frame (64 mm & above) x (50mm & above) & mullion 64 mm & above) x (70 mm & above).

UPVC - OPENABLE WINDOWS Providing and fixing factory made uPVC white colour openable glazed window / door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge including the cost of 8mm thick toughened Single glass panes and silicon sealent. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Openable door & windows including handle & locking arrangement with mullion transomusing R4 series with frame (64 mm & above) x (50mm & above) & mullion 64 mm & above) x (70 mm & above).

LAMINATES Providing & Fixing decorative laminate sheet of plain / wood grain in gloss / matt / suede and veneer finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive complete. - 1-1.25mm thick

SS HANDLE Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge.

FLOORING / STONE WORKS

Granite of any colour and shade

Area of slab upto 0.50 sqm

MOULDING Providing edge moulding to 18 mm thick stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-inCharge.

Granite work

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

VITRIFIED TILES Providing and laying Vitrified tiles in floor in different sizes in any finish (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

VITRIFIED TILES - SKIRTING Same as item above of S.No. 5.4 but in skirting

VITRIFIED TILES - IN WALLS/DADOS Same as item above of S.No. 5.4 but in walls/ dados.

Extra for providing Epoxy grouting with 3mm spacer in tiling works in lieu of cementitious grout, complete as per directions of Engineer in charge/ Architect.

Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of: (a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. (b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge.

300 mm Finished Floor Height (FFH)

WATER PROOFING WORK

Chemical Waterproofing

CEILING WORKS

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

BAFFLE CEILING Providing & fixing horizontal level suspended ceiling comprising of Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade 6063 T5. The baffle blade shall be in size of 100x25x3600mm in powder coated to Woodgrain/Plain finish (Red Oak, Cherry, Black & White).. The baffle shall be electrostatically polyester powder coated to a coating thickness of 60-80 micron. The powder coating shall pass Salt Spray Test for 750 Hours as per ASTM B117, QUV –A Test for 1000hours as per ASTM G-154 – (Cycle – 1) and Humidity test for 1000hours as per DIN 50017. The powder coating shall have an adhesion of GT0 as per EN ISO 2409. The shade variation within a manufacturing batch shall be delta E<1 using Excite/BYK Gardner instrument and gloss level 25±5 at 60˚ as per ASTM D523 (Not applicable of Wood Grain Shade). The baffle blade shall be suspended using Slotted U-profile of 20 x 30 x 3700mm (Thk-1.5mm) having 150mm on-center spacing. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with End caps. SUSPENSION: Shall be hanged using baffle hanger from U-profile made of mild steel with powder coating thickness of 60-80 micron. The U – profile to comprise of alternate square & rectangular slots of 6.5x6.5mm & 28x6.5mm respectively on the web for locking the baffle hanger using plugin clip to secure the hanger in perfect position and achieve uniform spacing between baffles. The overall dimension of the U – profile is 20(W) x 30(H) x 3750(L) mm and is rolled form from 1.5mm thick mild steel with a powder coating thickness of 60-80micron. U- Profile to be connected to each other using U –Profile Splice. The U- profile shall be hanged from the true ceiling using threaded rod using a U- Profile hanger.

PARTITION WORKS

MISCELLANEOUS WORKS

ROLLER BLINDS Providing & Fixing of Vista screen 5% or equivalent Manual Roller blinds, the Control unit is made of high strength reinforced plastic. The clutch is of wrap spring design. Clutchis operated directionally by the use of endless beaded chain. Idler is of high strength reinforced Plastic; control unit and Idler are mounted on powder coated M.S brackets Roller Tube is an anodized extruded tube of high strength alloy. Operating chain is made of 4.5mm Plastic beads molded on 2.2mm thick polyester Chord. Fixing bracket & clamps is made of mild steel and zinc plated. Roller tube is Aluminium alloy Extruded grooved tube, which is anodized. size-38mm-O.D:weight-0.27 kg \mtr Size- 38mm-O.D : Weigth-0.38kg/mtr size-50mm-O.D:Wieght-0.60 kg\mtr.Fabric is fitted to the bottom rail with plastic insert. Bottom rail end cap-made of ABS Fabric composition: -Fabric is made of 30% Polyester and 70 5 PVC with ALU coating, Openness factor 5 % Weight 419 GSM +-5% with fire resistance NFPA701 and having Environmental Greengard CertificationASTM-6329

ROLLER BLINDS - BLACKOUT Providing & Fixing of Vista serene Manual Roller blinds, the Control unit is made of high strength reinforced plastic. The clutch is of wrap spring design. Clutch is operated directionally by the use of endless beaded chain. Idler is of high strength reinforced Plastic; control unit and Idler are mounted on powder coated M.S brackets Roller Tube is an anodized extruded tube of high strength alloy. Operating chain is made of 4.5mm Plastic beads molded on 2.2mm thick polyester Chord. Fixing bracket & clamps is made of mild steel and zinc plated. Roller tube is Aluminium alloy Extruded grooved tube, which is anodized. size-38mm-O. D: weight-0.27 kg \mtr Size- 38mm-O.D : Weigth-0.38kg/mtr size-50mm-O.D:Wieght-0.60 kg\mtr.Fabric is fitted to the bottom rail with plastic insert. Bottom rail end cap-made of ABS Fabric composition: -Fabric is made of 100 % Polyster with pass blackout coating Weight 400 GSM +-5% with EPI/PPI-176/105 Warp 80 DenTwisted SD Welft-300 Den Roto.

ROLLER BLINDS - ACOUSTIC Providing & Fixing of Vista Manual Roller blinds, the Control unit is made of high strength reinforced plastic. The clutch is of wrap spring design. Clutch is operated directionally by the use of endless beaded chain. Idler is of high strength reinforced Plastic; control unit and Idler are mounted on powder coated M.S brackets Roller Tube is an anodized extruded tube of high strength alloy. Operating chain is made of 4.5mm Plastic beads molded on 2.2mm thick polyester Chord. Fixing bracket & clamps is made of mild steel and zinc plated. Roller tube is Aluminum alloy Extruded grooved tube, which is anodized. size-38mm-O. D: weight-0.27 kg \Mtr Size- 38mm-O. D: Weigth-0.38kg/mtr size-50mm-O. D: Wieght-0.60 kg\mtr.Fabric is fitted to the bottom rail with plastic insert. Bottom rail end cap-made of ABS Fabric composition: -Fabric is made of 35% Polyester and 65% PVC with ALU coating, Openness factor 5 % Fabric thickness 0.43mm fabric Weight 400 GSM Fabric width 160 to 320 cms fire Resistance ASTM/ASTM G with fire resistance NFPA701 and having Environmental Greeguard Certification- ASTM-6329/ASTM Acoustical performance NRC & SAA ASTM C423-09a UV Protection: Seal of Apporval by the Melanoma International foundation (MIIF) for effectiveness in preventing sun damage to the skin or eyes

SIGNAGE Providing & fixing 8mm thick pure monomer grade acrylic with custom colors with polished edges.LG or Avery Dennison or 3M signage films with exterior recommendation for decals. PU Paint will be Used for Custom base color as per approved shade. ( As Per Artwork Attatched), durability of Signage, complete as per entire satisfaction of Engineer-in-Charge. (Basic rate - Rs. 32/ Sq inch)

Hire charges of crane to place DG Set/ Other mechanical equpments on existing building terrace level complete as per directions of Engineer in charge.

ATT Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

CHEMICAL FOR ATT Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

RECEPTION TABLE - 8"-0" (L) X 2'-6" (W) x 3'-6" (H) as per drawing CF01 Finished with a)12mm Corian/Hynex acrylic surface front area including left and right side of table & 3" edges on the top as in drawing and rest in 1mm thick laminate. Rate to include 3" thick aluminium profile skirting,

CONFERENCE CONSOLE - 6"-8" (L) X 1'-0" (W) x 0'-8" (H) as per drawing no CF-02

JANITOR - 1"-6" (L) X 1'-3" (W) x 6'-6" (H) as per drawing CF-3. Note internal surfaces are to be laminated with 0.8mm thick sheet.

STORAGE - 1"-9" (L) X 1'-5" (W) x 6'-8" (H) as per drawing CF-5. Note internal surfaces are to be laminated with 0.8mm thick sheet.

PANTRY CABINET - RUNNING LENGTH 11'-6" (UNDER COUNTER ONLY) as per drawing CF-4 Providing & Fixing pantry cabinet factory finished made out of 18 mm thick prelamated HDHMR board. Shutters to be made with prelaminated particle board/MDF board wth edge banding of 2.0mm thick of matching shade at all exposed edges. rates to include hardware such as hinges, slides, locks, handles, screws, nails, connectors and so on complete as per directions of Engineer - in - Charge.

TRAINING ROOM PLATFORM - 19'-0"(L) X 4'-6" (W) x 0'-6" (H) as per drawing CF-5 Providing & Fixing wooden platform made out of 19 mm thick commercial board, supported on aluminium framework complete including all require fixing accessories like self cam screw, right angle connectors, screws etc where ever required complete as per directions of Engineer - in - Charge and attached drawing marked CF-5. (Aluminium framework to be paid separately). Rate to include finishing of exposed surface with 2.0mm thick Luxury Vinyl Tile (Ego or approved equivalent) fixed as per manufacturers guidelines.

Description

EUROPEAN WATER CLOSET Providing and fixing of wall mounted European style Water Closet (EWC) of size W 375, D 600, H 357mm including water and drainage connection with CI P traincluding all connections.Seat cover soft close with C.P brass hinges & rubber buffers of soft closing , Chair brackets/SS nut bolts etc., with flush Tank (concealed) of approved make as per the details mentioned below complete with drain outlets of 100mm dia C.I. sewage pipe laid in required slope and connected to drain pipes. Cost to include concealing of sewage pipe internally as instructed by the EIC / Architect.

Escale Wall Hung Toilet with Quiet close slim seat in White (Kohler) Cat No. K-16817IN-SS-0 or equivalent approved make

Flush Tank including brackets :INSTA FLUSH K-770217N-P-NA (Kohler) / Concealed cistern SISMA Q507450100 or equivalent approved make

Flush Plate : PEBBLE-K-54131N-P-CP PENUMATIC (Kohler) / Flush Plate SISMA Q507455120 or equivalent approved make

URINAL WITH SENSOR Providing and Fixing White glazed vitreous Chinaware urinals with integrated sensor including all fittings like CP brass flush pipe, CP brass spreaders with unions and clamps (all in CP brass), CP brass waste coupling 40 mm dia, inlet connection, concealed 'Z' CI brackets etc., all complete including cutting and making the good the walls and floors wherever required as per the architectural drawings, manufacturers specifiaction and as directed by the EIC / architect complete in all respects.

URINAL PARTITION Providing and fixing wall mounted frosted glass urinal partition 900x450 mm curved shape with 8mm thick glass, complete as per directions of EIC. Make Jaquar 1110-UC or equivalent

VANITY COUNTER Providing & fixing of Vanity counter In walnut finish complete as per directions of Engineer in charge.

900 mm Vanity - K31601IN- E 64 (Kohler) Vanity Top - K-2749T-1-0 (Kohler) or equivalent approved make

600 mm Vanity - K31602IN- E 64 (Kohler) Vanity Top - K-2660IN-1-0 (Kohler) or equivalent approved make

SS SINK Providing and fixing SS sink (grade 304) of size 600 mm x 450 mm with sink cock, bottle trap and other necessary fittings etc., all complete as per the direction of the EIC / Architect. Drawing No.: SEBI/03/2019

Nirali ECM Popular Range - Grade Plain Large (Glossy) Stainless Steel Sink - 600 x 450 mm

BOTTLE TRAP Providing and fixing CP Bottle trap complete including all fitting & fixtures and as per direction of Engineer. Make Kohler model K - 758231N-CP or equivalent

STOP COCK Providing and fixing in position CP brass concealed stop-cock with adjustable wall flange etc., complete as per directions of EIC/Architect. Make Kohler model K - 16088IN-CP or equivalent

ANGLE COCK Providing and fixing CP brass angle cock 15 mm size with CP wall flange. The rate is inclusive of CP connector upto 600 mm long etc., complete as per drawings and instructions of EIC/Architect. Make kohler, Model - 80158IN-9AV-CP or equivalent

PAPER HOLDER Providing & Fixing complementary sq toilet PPR Hold W/o Cov Complete in all respects Cat- 25070IN-CP, Make Kohler

TOWEL RAIL Providing & Fixing towel rail 24" long Complete in all respects Cat- 97495T-CP, Make Kohler or equivalent

BASIN MIXER Providing and fixing CP brass wall mounted basin mixer, complete as per drawings and instructions of EIC/Architect. Make kohler, Model - 5679IN-CP (Valve) and 5683IN-4ND-CP (wall mount) or equivalent

SINK MIXER Providing and fixing CP brass wall mounted sink mixer, complete as per drawings and instructions of EIC/Architect. Make kohler, Model - 37315IN-4-CP or equivalent

HAND DRYER Providing & fixing Hand Dryer with necessary screws etc., complete as per the directions of EIC / Architect. Bardon touchless hand dryer Cat- 5486T-2_OP, Make Kohler or equivalent

LOOKING MIRROR Providing & Fixing looking mirror of size 56cm x 86 cm complete as per the directions of EIC / Architect. Cat- 26052IN-BLL, Make Kohler or equivalent

SOAP DISPENSER Providing & Fixing soap dispenser complete as per the directions of EIC / Architect. Bardon touchless hand dryer Cat- 5487T-2_CP, Make Kohler or equivalent

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal dia Pipes

20 mm nominal dia Pipes

Providing, Fixing, Testing & Commissioning uPVC SWR pipes (Type-B) for soil, waste and vent conforming to IS 13592 along with all required fittings like tees, bends, cowls, crosses with or without access doors jointed with approved solvent cement fixed to walls and ceilings including angle supports with clamps complete including cutting holes in R.C.C/brick work (slab/beam/wall) and making good the floors, beams and walls with cement mortar where required complete of outer diameter. (Soil/ Waste pipe)

80 mm dia

110 mm dia

Providing and fixing uPVC pipes ( confirming to IS 4985-2000 ) including all fittings (plain or door) e.g bends, tees, offsets etc. and fixing with as recommended by the manufacturer, necessary fixing arrangement including cutting chase or holes in walls / floors and making good the same complete as per specification.

DESCRIPTION

L-SHAPE-WORKSTATION SIZE : 1500/1500L x 600D x 750H TABLE TOP WITH 1200MM HT PARTITION Workstations of overall main panel thickness 65 mm (+/-5mm) and height of 1200mm (+/- 5mm). The return panel shall be 30mm thick. The worktop shall be made up of 25mm E1 norm PLPB with matching PVC edge band 2mm thick. The worktop shall be provided with 65mm gromet cut & shall be supported on CRCA bracket with one side fixed on rectangular slot of frame vertical and other side to worksurface. The partition frame shall be made up of nonferrous 6063 grade alum alloy confirming to DIN ISO-2768-1 & fabricated through weldless technology & fitted with pre moulded M8 levellers zinc passivated for height adjustment. Frame shall have vertical & horizontal members; vertical channels have inbuilt groove with rectangular slots to fix cantilever / gable end brackets. Frame to frame shall be attached through male/ female hook mechanism pressure die casted parts made in zinc alloy. Adequate ribs to be given in extrusion profiles having variable thicknesses of 1.10mm to 2.50mm for better durability. Frame to post shall be attached by male/female hooks made up of 2mm thick CRCA material zinc passivated to 10-12 microns. Each frame shall be fitted with tiles, male & female hooks, two end cap at top and bottom. Bottom caps shall be provided with leveller fixing arrangement. all caps shall be of aluminium ADC-12 pressure die cast. top trip shall be flat aluminium confirming to DIN ISO-2768-1. Quoted product should be BIFMA level Two certified and same shall be verified from website The data & power cables provision to be given at different levels. skirting raceways shall be designed for snap fitting for data cables and for power cables raceway below worktop shall be provided. Tiles of overall thickness 6mm thickness constructed out of PLPB E-1 norms upholstered with fabric or Laminated tile should be slide to the grooves provided in aluminium frame vertically, two tiles on either side of the frame to complete the assembly. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2, AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). NEO SERIES - Featherlite or equivalent

METAL MOBILE PEDESTAL 1F + 1D SIZE: 400W X 450D X 600HT Specification: The overall size of metal pedestal shall be size of 400W x 450D x 600H. Metal pedestal shall be made of complete body and facia in 0.8mm thick CRCA. This pedestal shall be made of metal construction with anti-rust electrostatic spraying for long-lasting durability and bears up to 200lbs in total. Resistance soiling, resistance to water and resistance to stains. Its drawer shall be operated by Telescopic channels. Drawers open completely and smoothly, allowing you to easily access the contents in the back of the drawers. Easy to classify and storage items. Pedestal handles shall be Finger grove and it is groove shall be generally located around the upper edge or perimeter of the pedestal for easy handling. Pedestal shall be cylindrical multi lock shall be provided. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). EDGE SERIES - Featherlite or Equvalent

CONFERENCE-TABLE SIZE : 3000L x 1050D x 750H Table Top: 25mm thick Pre laminate particle board E1 norms with 2mm PVC edge lipping on all exposed edges. Two Long sides of the work surface shall be provided with reverse tapered edge design created by chamfering the board at 45 degree inside for 17mm length & keeping 8mm straight & then edges sealed with 2mm thick PVC Lipping on automatic machine. Leg: shall be made up of high pressure aluminum die casted 20 degree tapered, number “7” shape & oblong cross section of about 55mm on top, 45mm at bottom and of 725mm length to get 750mm table height, it acts as vertical structural support member, connected by a horizontal cross beams 50x25x1.6thk (16g) ERW tube & connected to the Aluminium diecast vertical legs through a high pressure Aluminium diecast 90deg – 02 way connectors. The connector should have “V” / “U” shape tapered groove for sliding a Aluminium diecast slider nut. The slider nut shall be an Aluminium diecast part that has same taper as of “V” / “U” shape in the diecast connector. Wire Management: 450mm Aluminium Flip Up and provision to mount swicthes and sockets on PVC cable dump and Vertical wire entry cover. Cross Beam: Leg to Leg shall be connected using cross beams made from 50x25x1.60mm (16g) Rectangular tube and to give floating look & to connect the table top with cross beams injection moulded polycarbonate spacers should be used of dia 61mm x 42.50mm H insert moulded with M6x1P zinc blue plated bolt of 22mm L.Spacer height including bolt should be 64.50mm. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). ENRICH SERIES - Featherlite or Equivalent

EXECUTIVE CABIN TABLE SIZE : W 2400 x D 2025 x H 750mm The overall size of main table shall be 2400L x 840D x 750H. With side unit 2000L x 500D x 610H.The table top shall be 50mm thick at the edges of the top.The table shall be made of prelaminate MDF board in melamine finsih. The useable top size shall be 2200L x 840 mm D. Table top corner shall be round and cover with aluminium extrustion. The modesty panel of the main table shall be made up of 13mm thick Pre-laminate MDF board. The modesty shall be design in honeycome pattern with PU/melamine finish. At the front side of table LED light strip shall be provided. The LED light increase the overall look of the table. The table top shall be rest on, one side of fixed pedestal and other side shall be on Extented return unit. Fixed pedestal shall have 2 equal drawer with finger grove handle ( handless desgin ). The tabletop shall have a leather pad with size of 1000mm x 440mm that gives a premium look. Side unit - Side table shall be size 2000 L x 500 D x 610 H with 16mm thick MDF board with melamine finish. Fixed side return with 2 drawers and 2 swing door. Fixed side return shall have flexibility to be placed left or right during time of first assembly. All the Drawer and shutters shall be operated by finger grove handle on the Drawer and shutter facia. The table top shall also have Standard wire provision with 3 socket upward and 2 scoket downward with size of 450L x 60W. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 , AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). HORISON SERIES - Featherlite or Equivalent

EXECUTIVE CABIN TABLE SIZE : W 2400 x D 450 x H 2000mm The overall size of back unit shall be 2350L x 400D x 1980H. The back unit shall be made of prelaminate MDF board with melamine finish.The storage shall have one openable shutter with size of 400W x 390D x 1960H made of 15mm thick board.The storage shall have open cabinet. The open shelf shall be made of 25mm thick partical board and in middel compartment. The top open cabinet shall have have provision of LED strip light. storage shall have open shelves to keep the awards, trophies or documents. Storages shall have multiples compartments with all other essential hardwares like hings, handles etc.. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory). HORIZON SERIES - Featherlite or equvalent

EXECUTIVE CABIN TABLE SIZE : W 2100 x D 1850 x H 750mm The overall size of table shall be 2100L x 1850D x 750H.The table shall be made of particle board with melamine finish. Table modesty panel shall have hard PU decorations.The table top shall have 45mm thick.Table top corner shall be round. The modesty panel shall be made up of 13mm thick Pre-laminate particle board. The modesty panel shall be connected through L-shape Bracket connector. The table top shall be rest on one side of fixed pedestal and other side shall be on Extented return unit. Fixed pedestal shall have 2 equal drawer with finger grove handle ( handless desgin ). table side unit shall have size of 1850L x 500D x 600H. Side unit shall have Fixed side return can be left or right when first assembly, including swing door, drawers and open space for CPU. Wire Management: 1 No. Aluminium Flip Up and provision to mount swicthes and sockets on metal cable Dump and vertebra considered for wire uptake from floor to cable dump. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). OASIS SERIES - Featherlite or equvalent

CAFE-TABLE Size : 1200 L x 800 W x 750 H mm with 18 mm thick Hydro shield top Under-structure: End Legs are constructed from, ERW CR Tube of 40mm x 40mm x 1.60mm thick (16g) Straight Legs, acts as vertical members of the leg. ERW CR Tube of 40mm x 20mm x 1.60mm thick (16g), which acts as horizontal member of the leg. Cross beams/ supports are from ERW CR Tube of 40mm x 20mm x 1.60mm thick (16g), tube end covered with injection moulded end cap. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). SWITCH SERIES - Featherlite or equvalent

STORAGE Top shall be made up of 18mm thick pre laminated particle board E1 norms and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. Shutters to be provied for compartment. Planter Box Shall height of 150mm to keep the planter pot. Edge: All exposed shall be sealed with 2mm thick PVC edge lipping. The hinged doors top shall be provided with finger groove handle-less design for a streamlined look. Finger groove shall be created by providing a reverse tapered profile edge of 6mm straight surface & 12 mm tapered towards inside @ 45 degree & then sealed with minimum 2mm thick PVC lipping on automatic machine. Cam Lock faciltity should be provided for safe storage of documents. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). EDGE SERIES - Featherlite or equvalent

Medium Height Storages 750 W - Size 750 W x450 D x 1200 H mm

Medium Height Storages 900 W - Size 900 W x 450 D x 1200 H mm

Medium Height Storages 900 W - Size 900 W x 450 D x 900 H mm

Medium Height Storages 1050 W - Size 1050 W x 450 D x 1200 H mm

Medium Height Storages 1050 W - Size 1050 W x 450 D x 900 H mm

Full Height Storages 1050 W - Size 1050 W x 450 D x 2100 H mm

TASK CHAIR The overall size of Chair shall be width 600 +/-5mm, depth 640 +/-5mm. Total height shall be 995 to 1095 +/-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 +/-5 mm, Seat Depth 470+/-5 mm and Seat height 470mm to 570 mm +/-5mm range. Seat shall be made up of foam pre moulded at 55 kg/m3 density. hardness of 25+ 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100% polyster 180 GSM abrasion > 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair shall be supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20%. Adjustable Lumbar Support made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. The Chair should be provided with Self Calibrating Multilock Mechanism (Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of the user. The mechanism shall allow 360 degree revolving feature along with height adjustablility. One Way Adjustable Arms (Height) to be provied with height adjustment button of size 73mm x 18mm made of Delrin P 500. The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon Base shall be provided.Twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. The base shall be 660 mm PCD (26 inches) five pronged bases made up of PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and strength.Tolerance of +/- 5mm to be considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). Amaze MB Featherlite or Equivalent

EXECUTIVE CHAIR - CABIN MAIN CHAIR The overall size of Chair shall be : Width 660mm , Depth 660mm & Height 1250 to 1350 mm. Seat Size shall be : width 490mm, Actual depth 520mm, Effective depth 430mm and height 475mm to 575mm. Width of the back shall be 425mm at bottom & Lumbar level 440mm & min 480mm at shoulder level. Back height shall be 690mm as measured from seat level. The chair shall be supplied with high quality Mesh at the back. Back outer shall be injection moulded with Nylon GF30% material. Seat should be made up of foam pre moulded at 55 kg/m3 density & hardness of 25+ 3kgf at 50% deflection conforming to IS 3400.The chair shall be supplied with Dynaflex Two Piece Back Construction with IS20D Mesh upholstred. Back shall be provided With 260mm width, 160mm height and 50mm height adjastable Headrest Thickness of seat foam shall be 55 mm. Seat shall be upholstered with micro fabric 100% polyster 180 GSM having abrasion > 50000 cycles fire rated fabric confirming to BS EN 1021. Plywood used shall be 12mm thick 9 ply hot pressed. The Chair should be provided with Synchro tilt Mechanism allowing 360 degree revolving movement along with height adjustablility & tilt tension. The mechansim shall allow seat to back recline ratio of 2:5. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Height adjustable Arms to be provied operated through button made of Delrin P 500. Arm pad material shall be polyurethane with 2mm metal insert. Nylon Base having PCD of 660mm five pronged base made up of PA6, 30% glass filled reincforced with bottom ribbing to be provided. 50mm dia twin castors with PA6 material to be provided.Tolerance of +/- 5mm to be considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). Liberate HB Featherlite or Equvalent

TRAINING CHAIR The overall size of Chair shall be: Total height 885 +/-5 mm, Back Width 415mm at Top and 470mm at bottom, Seat Width 490 +/-3 mm, Seat Depth 465+/-3 mm and Seat height 495mm +/-5mm . Over all chair width should be 600 +/-5mm and Overall chair depth should be 585 +/-5mm. Seat shall be upholstered with 100% polyster 180 GSM abrasion > 50000 cycles. No flamming or progressive smoldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair shall be supplied with Mesh at the back rest. The chair shall be supplied with injuction moulded Back rest with material of PA620%GF. The Chair understructure should be provided with 25.4x1.6 mm thickness Round tube. understructure shall connected with 4nos 50mm dia Twin castors PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. the axle pin shall be rust protected zinc passivated. Understructure shall powder coated upto 40microns. Fixed arms connected to Back rest with Textured arm pad with size of 290x38x3.5mm. Understructure shall powder coated upto 40 to 60microns. Injection moulded ABS writing tablet with370mm lenght, 265mm width and 10 thickness shall assembled for arm rest. Tolerance of +/- 5mm to be considered for product sizes i.e Length, Depth & height and tolerance of 5% to be considered in pipe thickness & Pipe sizes. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). Forum 4 legs Featherlite or equivalent

CAFE CHAIR The chair shall be made from a single-piece injection-molded polypropylene material with a half-round back contour to offer enhanced comfort and support. The overall width of the chair shall be 500 mm, depth 530 mm, and height 800 mm. The seat height from the floor shall range from 435 mm, and the back height from the seat shall be 400 mm. The backrest will feature a half-round contour, with a lumbar width from end to end at lumbar level shall be at least 450 mm and a top width of 430 mm. The front of the seat will include a waterfall edge with a minimum height of 25 mm. The seat width, measured from the center, shall be 440 mm, with a depth of 400 mm. The backrest will be perforated with a triangular pattern for ventilation and flexibility. Ribs beneath the seat, extending from front to back, will have a minimum height of 12 mm to enhance stability. The thickness of the chair at the various polypropylene edges shall range from 7 mm, 8mm, 9mm respectively. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory. Tang Chair Featherlite or equivalent

THREE SEATER SOFA 3 Seater Sofa : Overall size shall be 1800 W x 665 mm D x 775 H mm

SINGLE SEATER SOFA 1 Seater Sofa : Overall size shall be mm700 W x 665 mm D x 775 mm

SINGLE SEATER SOFA Single Sofa : Overall size shall be 980 mm W x 975 mm D x 820 mm H. Sofa inner frame structure shall be made from the combination of treated solid wood and plywood having high quality webbing belts to ensure good strength, rigidity & stable construction to offer high durability. There shall be extra padding between the armrest & the seat on both sides for better comfort & polyfilled in arms & backrest. The polyurethane (PU) foam shall be used in Seat & back rest having 40 density and 32 density respectively. Seat to backrest angle should be ergonomically designed to offer the best seating comfort. Seat height shall be normally between 16 to 18 inches and depth shall be between 20-22 inches. Sofa shall be elevated from ground by about 3 inches using Golden finished metal legs creating provision for easy cleaning & better look. Upholstery shall be of high quality Leatherite offer the best feel & comfort. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). W Series Featherlite or Equivalent

CORNER TABLE The overall size of the table shall be 600 L x 600 D x 450 H mm. The top surface of the table shall be in boat shape design having maximum size at the middle & lesser at the ends to form this unique shape. The table top shall be made up of 18mm thick Prelaminated particle board of E1 norms. The edges shall be sealed properly with 2mm thick PVC edge banding on automatic machine. The understructure of the table shall be made from solid wood i.e properly treated & seasoned kiln dried beach wood, finished with clear synthetic PU coating for the best resilence and high durability. The legs and the frame shall be joined together by method of tenon and mortise for durability and better aesthetics. Four legs shall be provided and the cross section of leg at the bottom shall be 35x35 and top shall be 55x35 provided in tappered finish for better looks. The outer side of the legs shall be rounded & inner side shall be corner edges. The wooden frame shall be of size 55mm x 22mm thick with visible face of 55 mm front and 22mm shall be below the table top running at all four ends as well as one support in the middle. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). Wooden Coffee Table Featherlite or Equivalent

Sofa inner frame structure shall be made from the combination of treated solid wood (Neem / Pine wood) and plywood, also webbing belts should be used for better strength, rigidity & stable construction to offer best durability. The polyurethane (PU) foam shall be used in Seat & back rest of 40 density and 32 density respectively. Seat to backrest angle shall be ergonomically designed to offer the best seating comfort. Seat height shall be normally between 17 to 18 inches and depth 20-22 inches. Sofa shall be elevated from ground by about 3 inches using metal powder coated legs, which creates provision for easy cleaning at the same time offers floating look. The fabric used for upholstery shall be 450 glm, having abrasion resistance more than 50K rubs, colour fastness to light better than 5, colour fastness to rubbing 4-5, high quality polyester fabric to offer the best feel & comfort. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). S Series Featherlite or Equivalent

THREE SEATER SOFA SIZE : 2050L X 790D X 790HT

SINGLE SEATER SOFA SIZE : 850L X 790D X 790HT

CENTRE-TABLE Size 800 Dia x 450 H (mm) Table top shall be 18mm thick Prelaminated particle board E1 norms and the Understructure shall be made up of 19x19mm square MS pipe having thickness of 1.6 mm. Frame shall be welded by CO2 welding process for uniform conforming to IS 816. Understructure frame shall be powder coated in black shade. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). Cosmo Series Featherlite or Equivalent

CORNER-TABLE Size 450mm Dia x 450 H (mm) Table top shall be 18mm thick Prelaminated particle board E1 norms and the Understructure shall be made up of MS pipe having thickness of 1.6 mm. Frame shall be welded by CO2 welding process for uniform conforming to IS 816. Understructure frame shall be powder coated in black shade. The manufacturer (OEM) shall have ISO 9001, ISO 14001, ISO 45001 & ISO 50001 issued from NABCB accredited agency, BIFMA Level 2 ,AIOTA certification. India Design Mark (Chairs, Tables, Workstations & storage one certificate in each category respectively is mandatory) , Green Guard Gold certification (Chairs,Tables,Workstations & Storage one certificate in each category respectively is mandatory). Grace Series Featherlite or equivalent

WIRING FOR ONE LIGHT POINT Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required,

Group - C

SUPPLY & LAYING OF STEEL CONDUIT Supplying and fixing of following sizes of Steel conduiut along with accessories in surface / recess including painting in case of surface conduit or cutting the wall and making good the same in case of recessed conduit as required.

WIRING FOR CIRCUIT / SUB MAINS Wiring for circuit / submain wiring along with earth wire with following sizes of FRLS / HFFR, PVC inslated copper conductor, single core cable in Surface / Recessed medium class PVC Conduit as required

BLANK MODULE Supplying and fixing modular blanking plate on the exixting modular plate & switch box excluding modular plate as required.

G.I. BOXES WITH 6A MODULAR SWITCH SOCKET Supplying and fixing suitable size G.I. Box with Modular Plate & Cover in front on surface or in recess. including providing and fixing 3 pin 5/6A Modular socket & 5/6A Modular Switch, connections, painting etc. as required.

G.I. BOXES WITH 6A&16A MODULAR SWITCH SOCKET Supplying and fixing suitable size G.I. Box with Modular Plate & Cover in front on surface or in recess. including providing and fixing 3 pin 5/6A & 15/16A Modular socket & 15/16A Modular Switch, connections, painting etc. as required.

G.I. BOXES WITH 6A&16A MODULAR SWITCH SOCKET Supplying and fixing suitable size G.I. Box with Modular Plate & Cover in front on surface or in recess. including providing and fixing 3 pin 5/6A & 15/16A Modular socket and 5/6A & 15/16A Modular Switch, connections, painting etc. as required.

LIGHT PLUG SOCKET (FOR UPS) Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 Nos 3 Pin 5/6Amp. Modular socket outlet, 1 Nos 16Amp modular switch & 1nos dummy Switch , connections etc. as required.

THREE PHASE MCBDB (TP & N) HORIZONTAL TYPE Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB Distribution Board, 415Volts, on recess, complete with tinned copper bus-bar, neutral bus-bar, earth bus-bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Legrand, Schneider, LK, ABB, Siemens

Legrand, Schneider, LK, ABB, Siemens

As Approval of Architect / Consultant

G.I. PLATE EARTHING Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal / coke and salt as required. (DG Body -2nos & Main LT Panel -02nos)

COPPER PLATE EARTHING Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. without charcoal / coker and salt as required. (DG Body -2nos & UPS -02nos)

6 SWG G.I. WIRE FOR LOOP EARTHING Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing etc. as required.

4 MM DIA COPPER WIRE FOR LOOP EARTHING Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing etc. as required. (for UPS) to be laid in existing PVC conduit on surface

Philips, Wipro, Lighting Technology, Havell`s

LAYING ON WALL SURFACE Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Upto 35 sq mm (clamped with 1 mm thick saddle)

Above 35 sq mm and upto 95 sqmm (clamped with 25 x 3 mm M.S. Flat Clamp)

Meter

CABLE END TERMINATION Supplying and making End Termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1KV grade as required.

6W CEILING/WALL SPEAKER Supplying, Installation,Testing & Commissionng of ciling / wall mount loud speaker 6 Watt in ABS box ceiling enclosure complete as required

DIGITAL AUDIO AMPLIFIER 75W Supplying, Installation,Testing & Commissionng of Digital Audio Amplifier 75 Watt, 25V rms operating 240 volts AC supply complete as required

SPEAKER CU. CABLE IN PAIR Supplying & drawing of cable Fire Retardent PVC Insulated copper conductor cable in the existing surface / recessed steel conduit of following Pair, Cores and size including connections and interconnections etc. as required

Speaker Cable Single Pair, 2 - Core, 1.5 sqmm

SILENT TYPE DIESEL GENERATING SET Supplying, Installation,Testing & Commissionng of Silent Type Diesel Generating Set as per CPCB IV + or better norms along with having Prime Power Rating of KVA as below, 415 voltsat 1500 RPM, 0.8 lagging power factor at 415 volt suitable for 50Hz, 3 Phase system & for 085 Load Power Factor, including testing at factory and site with fuel, Load for Test and other necessary arrangements. Complete as per CPWD Specifications, should have QR Code which should contain drawing, Test report, OEM Manual, Geo-Tag of manufacturing location, Rating Plate as per relevant IS Code etc. and Commissioning of the followings :

DIESEL ENGINE Tourbocharged Diesel Engine 4 Stroke Water Cooled, Multi Cylinder, Dynamically balanced fly wheel, Electric start of suitable BHP at 1500 RPM suitable for above output of Alternator at 40ºC, 50% RH & at 1000 Meter MSL, Capable of taking 10% over loading for ONE hour after 12 hours of continuous operation. The engine will be with Electronic Governor, Dry Type Air filter with service indicator, First filling of Engine Fuel (after commissioning) Lubricating Oil, Coolant and other consumables, complete with all the required accessories, The Electronic Governor shall be as per ISO 8528, The Engine shall comply to the latest CPCB norms (CPCB + or Better) and conforming to BS 5514, BS 649, IS 10000, IS 10002, IS 13018 and as per CPWD Specifications.

ENGINE MOUNTED INSTRUMENT PANEL FITTED WITH AND HAVING DIGITAL DISPLAY PLATE FOR FOLLOWING : Start - Stop Switch with Key Water Temperature Indicator Lubrication Oil Pressure Indication Lubrication Oil Temperature Indication Battery Charging Indication and Voltage Indication RPM Indication Over Speed Indication Low Lubrication Oil Trip Indication Engine Running Hour Indication Fuel Level

ALTERNATOR Synchronous Alternator Rated appropriate KVA, 415 volts at 1500 RPM, 3 Phase 50 Hz, AC Supply with 0.8 lagging power factor at 40ºC, 50% RH & at 1000 meter MSL. The Alternator shall be having Screen Protected Drip Proof (SPDP) enclosure IP 23, Brushless, Continuous Duty, Dynamically Balanced Rotor, capable of taking 10% over load for ONE hour after 12 hours of continuous operation, self cooled, self excited and self regulated through AVR conforming to IS 13364 (Part 2) / IS 4722 / BS 2613 suitable for tropical conditions and with Class - H Insulation

BASE FRAME AND FOUNDATION Both the Engine and Alternator shall be mounted on the suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendation of manufacturer.

DAILY SERVICE FUEL TANK Daily service fuel tank of suitable liters capacity as per CPWD Specifications, fabricated out of 3 mm thick M.S. Sheet complete with all standard accessories and Fuel piping between fuel tank and diesel engine with MS class "C" pipes of suitable dia. Complete with valves, level indications & accessories as required as per specifications.

DRY EXHAUST PIPE Dry Exhaust Manifold with Hospital Type Exhaust Silencer and Catalytic convertor

STARTING SYSTEM 12V / 24V DC Staring system comprising of Starter Motors, Voltage regulator and arrangement for initial excitation complete with suitable numbers of batteries (180 AH Capacity lead acid SMF type) as required as per specifications. The Battery shall be housed inside the acoustic enclosure of DG Set.

ACOUSTIC ENCLOSURE Acoustic and wheather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air into the atmosphare and the temperature rise inside the enclosure, noise level out side the enclosure. The acoustic enclosure should be suitable for capable connection / connection through bus-trunking. such arrangement on acoustic enclosure should be water proof conforming to IP 65 protection, The enclosure shallbe as per CPCB IV + or Better norms etc. and as per CPWD Specifications.

AUTO MAIN FAILURE PANEL Free standing floor mounted IP 42Automatic Mains Failure ControlPanel including Auto By-pass, suitable for KVA as below for silent type DG Set complete with relays, timers, set of CT`s for metering and protection and energy analyser to indicate Current, Phase & line Voltage, Frequency, Power factor, KWH, KVARH, KVA (Phase & Total), KW & provision for Over Load, Short Circuit, Restricted Earth Fault, Under Frequency, Power (Aluminium) and control (Copper) cableing of sutable size upto 15 meters between AMF Panel, LT Panel and DG Set including connection interconnections etc. as requird. allcomplete and inter locking and communication / Ethernet / RS485 / SNMP port open protocol for BMS integreation including suitable software, the panel shall be of DG Set OEM make etc. as per approved by Engineering-in-Charge and including the following :

Suitable numbers and appropriate capacity 4 Pole Motorised electrically operated drawout with cradle type 3 position ACB / MCCB with electronic release for O/C & E/F and Shunt Trip

Protection for Under & Over Voltage, Phase Reversal (2 nos OV Relay, 2 nos Reverse Power relay and 2 nos UV Relay)

3 Sets of Current Transformer 15P 10 accuracy for protection and 15 VA class-I for metering

Energy Analyser unit to indicate Current, Voltage (L-N, L-L), kW, kVA, (Phase & Total), Frequency, KWH, PF

LED Indicating Lamps for Load on Mains and Load on DG Set

Fuse / MCB for Instruments

Main Supply Failur Monitor

Supply Failure Timer

Restoration Timer

Control Unit with three impulse Automatic Engine Star / Stop and Failure to start lockout

Impilse counter with locking and reset facility

ON / OFFF / Control Circuit Switch with Indicator

Audio / Video announciation for i High Water Temperature ii Low Lubricating Oil Pressure iii Engine Over Speed iv Engine Fails to Start v Full Load / Maximum Load warning

Proection for OV, Frequency, Loss of AC Sensing, OC, Unbalancing Load with suitable number Relays and accessories

load management through PLC to achieve Auto Opening & Closing of Incomer Breakers, Bus-Coupler Switching off essential panel, Interlocking providingsignal to AMF Panel for Load status and AMF shall give command to DG Set to Auto Start / Auto Stop depending upon load status and requirements etc. and necessary hardware & software required to perform the operation shall be provided by the contractor including all necessary control wiring.

24 PORT SWITCH INDOOR TYPE Supply, Installation, Testing and Commissioning of following capacity 24 Port Layer 2 Indoor Network Switch having features and specifications etc. As per mentioned here under : Atleast 24 X RJ-45 Gigabit Ethernet Ports and additional 2 x 10G Base - T with 4 x SFP Ports with non-blocking architecture by having Switching capacity of minimum 168 Gbps and packet forwarding rate of 125 Mpps or higher, 16K MAC table. Console Port, USB Port, Stacking support of minimum 8 units per stack. Internal dual AC power supply, STP,RSTP, MSTP, BDBU Filter, BPDU Restriction, Min. 9k Jumbo Frame, LBD, IGMP Snooping V1/V2/V3, MLD Snooping V1/V2. IGMP / MLD Groups 1K or more, IPv4 / IPv6 Loopback Interface, 16 L3 IP Interface, IPv6 ND, VRRPv3, UDP Helper,ECMP, VAN : 802.1Q Port based, Q-in-Q, Multicast VLAN, protocol VLAN, VLAN Trunking, DHCP Snooping Server, Server Screening, RADIUS, TACACS+ Authentication, QoS : 802.1P, 8 queues per port, QoS : WRR, Strict+WRR, WRED, 802.1P. ACL : MAC based, IPV4C IP6 TCP / UDP Port number, time based ACL, TFTP Client, SNMP V1, v2c, v3, SNMP traps, RMON, DHCP Server, Relay, client, LLDP, LLDP-MED, OAM,Dying Gasp, 802.3ah, sflow, RIP, OSPF v2/v3, plicy basedroute, SSL, SSH, 6kV surge protectionon all GigabitEthernet ports and on all GE RJ-45 access ports. Certifications : UL, CE, FCC,RoHS, MTCTE, OEM / Product must be on the Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as required.

INDOOR WIRELESS ACCESS POINT FOR HIGH DENSITY Supplying, installation, Testing and commissioning of Indoor Wireless Access Point for High Density use having features and specifications etc.as mentioned here under :- Wi-Fi 6 (802.11ax) 574 Mbps (2.4GHz) + 2402Mbps (5GHz), Wi-Fi 6 Certified, 1 x RJ45 console + port, MG 2.5G LAN PoE Port, factory reset, WPA/WPA2/WPA3TM, Personal / Enterprise, WEP 64/128-bit, SSID broadcast disable, MAC address access control, Internal RADIUS server, SNMP, Customizable Captive Portal, Auto Channel, Works as Access Point, WDS, WDS with AP, Wireless Client, Web (HTTP), Secure Socket Layer (SSL), Traffic Control, Support ATF / Fast Roaming / Band Steering, Supports Enhanced security - WPA-PSK/WPA2-PSK/WPA3-PSK and RADIUS client, and Cipher negotiation, and MAC / IP ACL for networks, Certifications :- MTCTE.CE, FCC work as Standlone and must be Compatible with S/W & H/W Controller with additional features like Real -Time Monitoring and Alerts, Rich Advanced Features, Centralized Device Management, Role-Based Adminstration, Real-Time Monitoring, VLAN and Access Control, Auto RF Management and Bandwidth Optimisation, Multi SSID and captive Portal Authentication. OEM/Product must be on Trusted Telecom Portal of Department of Telecommunication, Government of India etc. complete as required.

24 PORT PATCH PANEL WITH 1 U RACK Supplying, installation, Testing and commissioning of 24 Port Cat 6A Patch Panel loaded. Must be of 1 U Height with clear label holders and white label with the panel . 24 Ports Cat 6A Patch Panel should have ETL / UL verification program certificate for compliance with ANSI / TIA-568.2-D etc. Complete as required.

PATCH CORD Supplying, installation, Testing and commissioning of Cat 6A Patch Cord should have ETL / UL verification program certificate for compliance with ANSI / TIA-568.2-D etc. Complete as required.

Copper Patch Cord of length 1 m (3ft)

Copper Patch Cord of length 3 m (10ft)

CAT 6A INFORMATION OUTLET (IO) Supplying, installation, Testing and commissioning of CAT 6A Copper Information Outlet (IO) with Faceplate of colour as per site requirement, should have ETL / UL verification program certificate for compliance with ANSI / TIA-568.2-D. All Copper cable & Components should from same OEM to maintain compatibility and interoperability etc. Complete as required.

CAT 6A UTP LSZH 23AWG CABLES Supplying, installation, Testing and commissioning of CAT6A UTP LSZH 23AWG Twisted Pair Cable in existing conduit on surface / recess, U / FTP, LSZH, Non-Plenum, Horizontal (Solid) Cable suitable for high speed data networking application supportig upto 10Gbps over a 100meter channel. The 4 Unshielded Twisted pair UTP Cable with color coded insulation for easy identification should have FLAME PROPERTIES i.e. Flammability Test - IEC 60332-1, Smoke Density - IEC 61034, LSZH standards compliance : ANSI / TIA - 568 C.2, ISO / IEC 11801, IEEE 802.3an, RoHS. Delay Skew should be < 45NS. The outer Cable Diameter should be 7.5 + 2mm. Cable should have been tested and verified by UL / ETL etc. Complete as required.

Meter

Meter

Meter

Meter

42U RACK Supplying and fixing of 42U Rack with 6" Caster wheels and front brake Floor Standing Rack with main Frame Piller of 1.6mm Powder Coated CRCA Sheet with removable side panels, L- shape adjustable Vertically Mounting Rail of 2 mm with "U" Marking completely knocked down (CKD) shape, fitted with 4 number cooling fans, minimum 8 nos two line cable entry / exit provision at top and bottom with rubber protection. Front Door 5 mm Toughened Glass with MS Farme or perforated with lock, Rear MS vented or perforated door, Powder Coated Color RAL 7035 or black, complied with UL & RohS, 2 x 6 sockets 16A power distribution units, 3 numbers closed cable organiser, hardware mounting screws packet of 20 x 1 number, etc. complete as required

4 MP IP IR DOME CAMERA Supplying, installation, Testing and commissioning of 4 MP IP IR Dome Camera having following specificatins features etc. :-

Signal System - PAL / NTSC, Signal to Noise Ratio, > 50dB, Camera should display Camera Title, Date & Time in live & recorded vedio

Image Sensor - 1/2.8" or better progressive Scan CMOS to get color image even at night conditions (minimum Illumination - 0006 Lux @ F 14, AGC On, 0 Lux with IR or better) True Day & Night High Perfoemance Mechanicl IR cut filter with auto switch, Integreted IR Source (Auto, Manual) - inbuilt IR LED`s with effective distance upto 50meter or better and 30meter for color view in night, Imaging 1/3s to 1/30000s electronic shutter support, Auto Gain Control, White Balance - Auto, Back Light Compensation, Multi Zone Privacy Masking, HLC, Digital Water Marking.

Compression (Minimum) - Video - H.265 or better, H.264H, H, 264, Audio - G.711U/A, G 7.11Mu, G.726, AAC, G723

Wide Dynamic Range - WDR (120dB or more)

Digital Noise Reduction- DNR (3D) On / Off

Video Streaming & Frame Rates - tripple streaming , configurable (main Sream - 2MP (1920 x 1080) @ 25/30 fps, Sub streas minimum 720P @ 25/30 fps

Onboard Storage- Camera should support built-in Micro SD/SDH/SDXC Card slot upto 512 GB. It should be supplied with minimum 128 GB memory Card

Standards - BIS with ER, STQC Certified, CE, FCC, and RoHS

NETWORK VIDEO RECORDER (NVR) 256 Mbps INCOMING BANDWIDTH Supplying, installation, Testing and commissioning of following channel Network Video Recorder (NVR) with Camera Licenses to record for all channels having specifications and features etc. As mentioned below ;-

Network Video Recorder Embedded / Installed OS (Linux) along with Camera Licenses for number of Channels of NVR to record per NVR and to provide a live view, storage and simultaneously Multi-Channel playback of all IP, IR Camera or more and mustbe ONVIF with minimum support of 26Mbps incoming Bandthwidth.

NVR should support H265 orbetter, H264, MJPEG, MPEG4 support.

Must support 1 channel input, 1 channel output, RCA for Two way talk

Intelligent auto power on when power resumes after power outage

Storage - It should support minimum 2 SATA Slots with 20TB capacity slot

Connectivity Interface - 1 nos x 10/100/1000 Mbps Ethernet Ports, 1 x RS 485, 1 x RS 232

Alarm Ports - It should have 4/1 ch In / Out Ports to connect varius type of external sensors and output devices like hooter / siren etc.

Must support Continuous, Alarm, Motion, Instant, Panic Recording Mode

The Network Video Recorder (NVR) shall be configured to send email whenever a system massage is created or an alarm event occurs. The email server shall be valid SMTP server. Each recipient email address shall be configured to receive any combination of crtical, warning, or informatin messages or alarm notifications. When an alarm occurs, the email message includes the NVR name, time of alarm and a list of camera that is configured to record upon alarm.

General AI Based Search - Search Pictures by channel, time, event type, target classification (Fall) Detection, people approach detection, People No. Exception Detection, People Staying Detection, Violance Detection

HARD DISC DRIVE Supplying, installation, Testing and commissioning of following capacity Serveillance Grade Hard Disc with upto 256MB/s Transfer Rate, 256 MB Cache, 7200 RPM Disc Speed, 3.5" form Factor, SATA Interface, BSMI, ICES-003/NNB-003, CE, FCC, KC, Maghreb, RCM, UKCA, VCCI, CB-Scheme, TUV, UL Certifications.

ACCESS CONTROL FACE / FINGER PRINT / SMART CARD / QR CODE SYSTEM Supplying, installation, Testing and commissioning of Access Control System comprising of Face & Finger Print Recognition, Smart Card, QR Code, NFC & PIN Code based Reader, following sizes of 5" IPS TFT Touch Screens, 1 GB RAM, 8 GB ROM, Live Face Detection with anti-spoofing against 2D photograph, mobile selfie & video, Fake Finge Print and Face Detection Technology, 30,000 Face Storage (1:N) /, 3000 Finger Prints (1:N), QR Code 30,000, 30,000 Cardstorage (1:N), 2 Lakh Transection storage, 20,000 image logs, onboard dual camera (color & IR) Primary Camera min. 2MP, Support Face authenitcation & verification from up to 1 meters, Communication Protocol Wi-Fi, TCP/IP, Wiegand Out, Wiegand IN, USB, MQTT protocol, Blacklist Employee Management, User wise authentication modes, Built-in Lock Control, Mask Detection & Alert (Configurable), 40 to 30,000 Lux Illumination, IP65 for Ingress Protection, Certification - CE, FCC, BIS, ROHS, etc. Metal Enclosure with Battery backup, suitable for mounting on metal surface / metal frame / wooden Frame / wall / flap barriers including all mounting bracket & accessories complete etc. as required.

SOFTWARE FOR WEB BASED ACCESS CONTROL SYSTEM Supplying, Installation, Testing and commissioning of Web Based Access Control System Enrolment and Device Configuration Software, should be independent of OS (Windows), Unified Management of Biometrics, Card & Controllers, Import Functionality for bulk user details,Biometric Template Retrieval for Data recovery, User Management, logs and Terminal Management, Support for IP- Based and USB Biometric Devices, User Specific Access Policies, Different user Policies on the Same terminal. Assignment of Specific Access Schedules, Pushing User to Terminals or Groups, Admin Authority Management to define rights of each user to perform, Blacklist UserManagement, Access Schedule Creation, Real-Time Log Retrieval. Real-Time User Identification, Secure Storage of Biometric / User Data, Capable to integrete with 3rd party applications over Web API`s, MQTT Protocol Support

ELECTROMAGNETIC LOCKS Supplying, Installation, Testing and commissioning of Electromagnetic Locks (Fail Safe time) for following type of Doors suitable for operation on 12 V DC having holding force 600 lbs for Single Leaf Door and 1200 lbs for Double Leaf Door with suitable feedback i/c connection complete etc. as required

Single Door Door

EXIT PUSH BUTTON Supplying, Installation, Testing and commissioning of Heavy Duty SS Finish Exit Push Button for releasing access doors with all necessary installation accessories i/c connection complete etc. As required

DOOR POSITION SENSOR Supplying, Installation, Testing and commissioning of door Position Sensor i/e connection complete etc. As required.

LT PANELS Design, Manufacture, Loadingg, unloading at Site, Supply, Erection, Testing & Commissioningat Site Cubicle type (bolted & modular construction) panels, fabricated out of 1.6 mm / 2mm (All load bearing member, Doors shall be 2mm and other parts shall be 1.6mm, Doors shall be Wavy free) rust inhibited CRCA sheet steel, 7 tank treated sheets and powder coated shall be complete with incoming and out-going feeders, electrolytic grade (E91) aluminum bus-bar, duly insulated with heat shrinkable PVC colour coded sleeves, shrouders, bus-bar droppers, supported on DMC/SMC insulators. Panel construction shall be TOTALLY TYPE TESTED ASSEMBLY (TTA) AND PARTIALLY TYPE TESTED (PTTA) and fool proof protection from dust, water, humidity, fire, vibratioins, temerature, variations, pull tension, noise, entry of rodent etc. (as per IEC 61439, IS : 13947 Part-I-IV, 1993, with heavy duty neoprene gaskets. The floor mounting panels shall be provided with mounting channels not less than 75mm X 75mm X 5mm thick of size (or Approved by Client / Consultant). Panels shall have aluminum earth bus through out the panel, The panel shall be provided with name / designation plate for all incoming/ outgoing feeders, danger plate, door steel locks etc. The key should be common for all compartment / doors. The doors of compartment should not open when switch is in ON position and provision of de-interlock facility shall be provided. Internal control / power wiring of the panel shall be carried out with FRLS insulated copper conductors PVC insulated. All tests shall be carried out as per IEC 61439-1 & 2 in presence of client or his representative and all tests certificates shall be submitted to the client in original duly signed by concerned authority. The switchboard shall be proven design from the Main Original Switchgear Manufacturer (OEM) Documents to be provided in respect of Franchise from the OEM. NOTE : All panels Switchgear / Accessories shall have 1 Year warrantee / Guarantee from the date of commissioning or 18 months from the date of supply etc. Also provide 3 Hard copy sets of Drawings to the client as built (Includes GA, Control Wiring & SLD) Including

脀܇ᬀ䕇䕎䅒⁌低䕔䘠剏䌠乏剔䍁佔癒桔⁥慲整⁳潦⁲污桴獥⁥瑩浥⁳湵敤⁲桴⁥潦汬睯湩⁧敨摡⁳桳畯摬椠据畬敤愠汬渠捥獥慳祲椠整獭愠摮攠畱灩敭瑮⁳獡爠煥極敲⹤䄀獳浥汢湩⁧潬獯⁥潣灭湯湥獴漠⁦桴⁥慶楲畯⁳煥極浰湥⁴獡瀠牥洠湡晵捡畴敲❲⁳湩瑳畲瑣潩獮漠⁲獡瀠牥愠癤獩⁥景䔠杮湩敥⵲湩䌭慨杲⁥š䈀湯楤杮漠瑮慭潳牮⽹潣据敲整眠牯湩汣摵湩⁧畣瑴湩⽧牤汩楬杮栠汯獥琠牨畯桧眠污獬是潬牯⁳湡⁤牧畯楴杮眠瑩⁨散敭瑮†潭瑲牡ㄠ㈺㐺⠠牰癯摩⁥桴⁥楦楮桳氠癥汥弩牐癯摩湩⁧污楦楸杮愠捣獥潳楲獥猠捵⁨獡渠瑵ⱳ猠牣睥ⱳ戠汯獴‬湁档牯䘠獡湴牥⁳瑥⹣愠⁳敲畱物摥堮晅敦瑣湩⁧摡煥慵整愠摮瀠潲数⁲潣湮捥楴湯⁳潴琠敨洠楡慅瑲楨杮匠慴楴湯⁳䄨⁓䕐⁒卉㌠㐰⤳Å吀畯档湩⁧灵愠汬搠浡条摥瀠楡瑮漠敶⁲煥極浰湥⁴楷桴猠浡⁥祴数猠慨敤愠摮瀠楡瑮湩⁧桴⁥卍愠杮敬Ⱐ䌠挭慨湮汥⁳瑥⹣眠瑩⁨睴潣瑡⁳景删摥传楸敤☠吠潷䌠慯獴漠⁦映湩獩楨杮†灡牰癯摥猠湹桴瑥捩攠慮敭慰湩⹴J䄀汬椠整獭氠獩整⁤湩琠敨䈠兏猠慨汬戠⁥景愠灰潲敶⁤慭敫漠汮⁹獡瀠牥琠湥敤⹲儠湁⁹湵灳捥晩敩⁤瑩浥猠慨汬戠⁥獡瀠牥愠灰潲慶景挠湯畳瑬湡⁴ 牁档瑩捥⁴ 睏敮⹲⤠汁楄楧慴敍整獲猠慨汬栠癡⁥卒㐠㔸倠牯穴汁慐敮獬䌯扵捩敬猠慨汬戠⁥牰癯摩摥眠瑩⁨畳晦捩敩瑮渠浵敢⁲景匠慰散䠠慥整獲⠠〸圠瑡獴 潃瑮潲汬摥戠⁹桔牥潭瑳瑡⁥湡⁤䍍⁂a䄀汬眠物獥甠敳⁤湩琠敨瀠湡汥猠慨汬戠⁥畭瑬獩牴湡敤⁤潣灰牥挠湯畤瑣牯䘠䱒⁓湩畳慬整Ɽㄠ〱嘰䜠慲敤‮×䌀⁔…慅瑲⁨楷敲⁳桳污敢㈠㔮煓洮潣灰牥挠湯畤瑣牯‬剆卌‬噐⁃湩畳慬整⁤湡⁤潃瑮潲楷楲杮渠瑯氠獥⁳桴湡ㄠ㔮煳浭‬剆卌‬噐⁃湩畳慬整Ɽ挠灯数⁲潣摮捵潴⁲桳污敢甠敳⹤†潃潬⁲潃楤杮猠慨汬戠⁥獡瀠牥琠敨䤠⁓瑳湡慤摲‮§一瑯⁥›湁⁹瑩浥猠敥獭琠敢洠獩楳杮愠摮渠敥敤⁤潦⁲浳潯桴爠湵楮杮是湵瑣潩楮杮漠⁦桴⁥祳瑳浥猠慨汬戠⁥牴慥整⁤獡椠据畬敤⁤湡⁤潮攠瑸慲瀠楲散眠汩敢瀠楡⁤潦⁲桴⁥慳敭‮÷䄀畬業楮浵䈠獵慢⁲桳污敢䔠敬瑣潲祬楴⁣片摡⁥‭㥅⸱䈠獵慢⁲桳污敢搠汵⁹潣敶敲⁤楷桴栠慥⁴桳物湡慫汢⁥噐⁃湉畳慬整⁤潣潬牵摥猠敬癥⹥丠略牴污戠獵猠慨汬戠⁥煥慵潴琠敨倠慨敳䈠獵‮䌊牵敲瑮䐠湥楳祴映牯䄠畬業畮畢⁳桳污敢挠湯楳敤⁲獡〠㠮⁁ 煓洮ê䄀汬䄠䉃猠慨汬戠⁥䑅ⱏ䰠䥓䝎‬㘠〹ⱖ䔠牡桴䰠慥慫敧‬⽏ⱖ唠嘯‮⽓⁃牐瑯捥楴湯‬楍楮畭〱䘠畡瑬䠠獩潴祲‬湅牥祧䴠慥畳敲瑮⁳污慐慲敭整獲‬䑉呍⁌牰瑯捥楴湯⁳瑥⹣䌠湯牴汯嘠汯慴敧㈠〳⁖䍁‬〵穈‬慍敫ⴠ匠档敮摩牥‬䉁ⱂ匠敩敭獮‬䭌‬敌牧湡魤汁敳瑴湩獧漠⁦敒慬⽹敒敬獡獥漠⁦䍁⽂䍍䉃猠慨汬戠⁥敳⁴獡瀠牥琠敨爠煥極敲敭瑮漠⁦桴⁥楳整愠摮椠⁴楷汬戠⁥湩琠敨猠潣数漠⁦慍畮慦瑣牵牥琠牨畯桧䌠湯牴捡潴⹲桔⁥畂⵳慢⁲畳灰牯獴猠慨汬戠⁥湯䌠獡⁴灅硯⽹删獥湩 楆敢⁲汇獡⁳湉畳慬潴⽲䐠䍍愠摮猠穩摥愠⁳数⁲偃䑗猠数楣楦慣楴湯⹳吠敨氠癩⁥慰瑲⁳景琠敨瀠湡汥猠慨汬戠⁥桳潲摵摥振癯牥摥戠⁹湵戭敲歡扡敬瀠汯捹牡潢慮整猠敨瑥眠瑩⁨畳瑩扡敬眠牡楮杮猠楴正牥浳汁呃獠猠慨汬戠⁥慃瑳删獥湩吠灹ⱥ†潦⁲敍整楲杮䌠ⵌ⸱ⰰ䈠牵敤㔱䅖‬…潦⁲牐瑯捥楴湯䌠ⵌ倵〱‬畂摲湥ㄠ嘵ⱁ删
潃瑮捡潴⁲潴猠扵業⁴桴⁥牯杩湩污吠獥⁴散瑲晩慣整琠睏敮⁲牦浯丠䉁⁌牯琠敨物愠瑵潨楲敺⁤慬潢慲

- 01set ®BUSBAR Aluminium busbar 100 amp, TPN with colour coded sleeves, Aluminium Grade E-91, Neutral Bus shall be equal to the Phase and Currenty density 0.8Amp per sqmm. - 01set"y63A , FP, MCB, 10kA, Curve - C + 63A FP, RCCB, 30mA Sensitivity -1nosy40A , FP, MCB, 10kA, Curve - C + 40A FP, RCCB, 30mA Sensitivity -3nosy25A , FP, MCB, 10kA, Curve - C + 40A FP, RCCB, 30mA Sensitivity -1nos+12WAY MCB DB DD WITH CABLE END BOX (AS UDB) Supplying/fixing/commissioning of Double Door DB suitable for three pole and neutral, prewired, sheet steel, Powder Coated, MCB distribution board, 440 volts AC, 50Hz, on recess including 63A FP MCB, 10kA, Curve-C and Top & Bottom Cable End Box for dressing of wire etc. MCB DB shallhave Three Neutral Bus Bar one nos for each phase 2 nos Earth Busbar including fixing the existing MCB / RCCB as per required quantity including connecting the terminal with eathing syste. complete in all respect as required. +"#Philips, Wipro, Lighting TechnologyRollÊ
10WATT LINEAR COLLIMETER LIGHT FIXTURE S/I/T/C of Recess Linear Collimeter Lens Luminaire having 545 MM Length. P.F.>0.95 with Driver, Fixing accessories etc. & THD<10% ,CCT 5700 K/4000K, CRI 80.The LED with Useful life of 50000 Hrs at L70. The Input voltage range shall be 140V to 300V Fixture have Surge Protection 3kV, Complete in all respect as required including connection etc. (Ref Model - Wipro LM04-261-45-57-RWX or Equal) Make: PHILIPS, WIPRO, LT&²
`20WATT ±1 WATT LINEAR FIXTURE 50 X 1200MM S/I/T/C of Recess Linear 4 Feet Fixture suitable for stand alone in Recess mounted having Extruded Aluminium housing with HET diffuser & including Driver, fixing accessories etc. with minimum system lumen efficacy of 115 lm/W with system lumen 2300lm , P.F.>0.95 with THD<10% ,CCT 5700 K/4000K, CRI 80.The LED with Useful life of 50000 Hrs at L70.The Input voltage range shall be 140V to 300V .Fixturehave Surge Protection 3kV, including connections etc. complete in all respect as required. (Ref Model - Wipro LM34-251XXX-57RMG1 or Equal) Make: PHILIPS, WIPRO, LT*GØ
36WATT 1WATT LED LIGHT FIXTURE 1' X 4' S/I/T/C of Led fixture Recess mounted Mounted with HET diffuser with having minimum system lumen efficacy of 120lm/Wwith CRCA Housing, Driver & fixing accessories and with P.F.>0.95,THD<10%,CCT5700 K, internal surge protection 2.5KV with input voltage range of 150V-270V,CRI 80.The LED shall be tested with LM80-08 standard with Useful life of 50000 Hrs at L70 . (Ref Model - Wipro CRCO13R036HP57 or Equal) Make: PHILIPS, WIPRO, LT&À
X12WATT FOKUS LIGHT FIXTURE S/I/T/C of Recess Fokus LED Light Fixture having Pressure Die CCast Aluminium Housing for better heat dissipation, Deep Optics for low glare, and beam angle 026 - 26º, 038 - 38º, 040 - 40º & 060 - 60º, includinf external driver having P.F.>0.95, Fixing accessories etc. & THD<10% ,CCT 5700 K/4000K, CRI 80.The LED with Useful life of 50000 Hrs at L70. The Input voltage range shall be 140V to 300V Fixture have Surge Protection 3kV, Complete in all respect as required including connection etc. (Ref Model - Wipro LD07-131-040-57-57- WH*or Equal) Make: PHILIPS, WIPRO, LT@û150MM SWEEP IN-LINE FLOW EXH. FAN S/I/T/C of 6" / 150mm Sweep 6"/ 150mm dia Axial Air Flow,Exhaust Fan Roof Mounted (Roof Exractor) each complete with Fan Impeller of Cast Alloy Alluminium Construction (LM -6 Grade) with blades of Aero-Foil Design "CGL, Khaitan, Havell`s©
1.1KV COPPER POWER CABLES Supply, Handling, Shifting, Testing and Commissioning of the Copper Conductor XLPE insulated,PVC sheathed, armoured, FRLS Cable of sizes as specified. The cable shall conform to IS 1554 Part I Contractor on receiving the Cable Drum must Megger the the Cable Drum for Insulation and after laying the cable each length of cable shall be meggered and submit report of healthyness of cable to client.")KEI, RR Kable, Polycab, Havell`s, Finolex&3C X 2.5 Sqmm 2XWY Cable (Panel to DG)&4C X 2.5 Sqmm 2XWY Cable (Panel to DG)'19C X 1.5 Sqmm 2XWY Cable (Panel to DG)"4C X 10. Sqmm 2XWY Cable (for ODU)71C X 16. Sqmm 2XWY Cable (for UPS & DG Neutral Earting)º
1.1KV ALUMINIUM POWER CABLES Supply, Handling, Shifting, Testing, Laying and Commissioning of the Aluminium Conductor XLPE insulated, PVC sheathed, armoured, FRLS Cable of sizes as specified. The cable shall conform to IS 1554 Part I, Contractor on receiving the Cable Drum must Megger the the Cable Drum for Insulation and after laying the cable each length of cable shall be meggered and submit report of healthyness of cable to client.";3.5C X 185Sqmm FRLS, Ar. Cable (A2XFY) for Laying Refer SLD:3.5C X 50Sqmm FRLS, Ar. Cable (A2XFY) for laying Refer SLD.
REMOVING OF EXISTING MATERIAL Removing of Existing Conduits /Cables/ Panels / DB`s etc. And storing them at a location provided by the client lead upto 50Mtrs also any of the Light / power or any other service gets disturbed shall be made operational. Complete in all respect as required by the client."Lot=METAL RACEWAY 300 x 38 x 1.5MM THICKNESS G.I. (275GSM) WITH COVER S/I/T/C of Sheet Metal G.I.Three Track Raceway with cover including fixing clamps, joints coupling, nuts, bolts & washers etc., The raceway should have one three compartment with suitable size of Junction Box having up & down height adjustment between 65 to 90mm. The raceway shall be fabricated out of 1.5mm G.I. Sheet and junction box shall be fabricated out of 1.5mm G.I. Sheet. The raceway is to be installed under the floor tiles and top of the junction box shall be in level with the floor tile. The job includes floor cutting, fixing of raceway & raceway junction box, riser box and making good with the help of cement mortar including all types of hardware required to complete the job. Complete in all respect as required. MAKE : - LEGRAND, M.K. OBOA"ÎMETAL RACEWAY 1.5MM THICK G.I. 3 TRACK WITH COVER S/I/T/C of Raceway/under floor trunking Three Compartment Size : 300 x 38 mm x 1.5 mm thick G.I. having 275GSM 88, to be supplied In the Length of 2.44mtrs 1Legrand, OBO, MKqFLY - OVER JUNCTION BOX ACCESS BOX Fly-Over Junction Box 300 x 300 x 1.5MM Thickness Height Adjustable 65 - 90 MM"VERTICAL RISER / VERTICAL ACCESS BOX Vertical Riser of size 300 x 300 x 15mm thicness made out of 1.5mm G.I. sheet having 275GSM $"{COUPLING PLATE Size : 300 x 38 mm x 1.5 mm thick Raceway Coupler with G.I. 275GSM of suitable size nut & bolts with washerjFIXING BRACKET Size : 300 x 38 mm x 1.5 mm thick Raceway Fixing bracket with G.I. 275 GSM of suitable size)Site Cover for Adj. Fly-Over Junction BoxA
FIRST AID BOX Supplying standard First Aid Box with necessary antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-aid) adhesive tape for medicinal use, scissors, anti-septic solution (Savlon or simlar) etc. (All above contents shall be standard makes) "!."*As Approved by Architect/ Consultant/ SEBIExtron, AMX, KRAMER, LEGRANDGRAND TOTAL AMOUNT RS.PIPES & ACCESSORIESŒ
Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. 150 mm. DiaMetrer
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

100 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Stainless steel

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.

20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585

Drum and brackets for fixing the equipmets on wall.

Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required:

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :

Pendent Sprinler

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.

100mm dia

Supplying, installation, testing and commissioning of splinker flexible pipe ( ul listed) of stainless stell complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Brust) with branch pipe (inlet ) 25mm NPT male thresd to splinker head ( Outlet ) 15mm NPT female thread with reducer , nipple, 2 side brackets, center bracket, stockbar of folowing sizes complete as required .

Two Loop Panel

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of intelligent interface unit BACnet/ Modbus protocol i.e. supplying communication links between building management system and fire alarm control panel complete as required.

Supplying, installation, testing & commissioning of fire fighter phone jack complete as required.

Supplying, installation, testing and commissioning of splinker flexible pipe ( ul listed) of stainless stell complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Brust) with branch pipe (inlet ) 25mm NPT male thresd to splinker head ( Outlet ) 15mm NPT female thread with reducer , nipple, 2 side brackets, center bracket, stockbar of folowing sizes complete as required .

PUBLIC ADDRESS SYSTEM

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at 240 volt AC supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with microphone assembly complete as required.

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.

speaker cable Single pair, 2-core, 1.5 sqmm

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

TOTAL OF INTELLIGENT FIRE ALARM SYSTEM

GRAND TOTAL OF FIRE FIGHTING WORKS

HVAC WORKS

OUT DOOR UNITS:

Supply, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum two compressors (with individual separate PCB) for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better efficiency condenser fan shall be capable to operate at different speed with respect to load. The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39 Degree Celcius.The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building)

For Cooling or Heating or Both

10.0 HP HEAT PUMP TFA

14.0 HP HEAT PUMP

16.0 HP HEAT PUMP

Supplying, installation, testing and commissioning of splinker flexible pipe ( ul listed) of stainless stell complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Brust) with branch pipe (inlet ) 25mm NPT male thresd to splinker head ( Outlet ) 15mm NPT female thread with reducer , nipple, 2 side brackets, center bracket, stockbar of folowing sizes complete as required .

Supply, Installation, Testing and Commissioning of following minimum ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

High Static Ductable units (minimum 78 pascal external static pressure)

speaker cable Single pair, 2-core, 1.5 sqmm

Supply, Installation, Testing and Commissioning of following minimum Floor Standing Duct Type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 415 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Supply, Installation, testing & commissioning of following Ceiling suspended TFA units with cordless/corded remote controller. Fully Factory assembled, wired and tested TFA Units as per specifications and as required to make the system complete. All Units shall have to be equipped with the drain Pump.

1236 CFM (TFA) (10.0 HP)

1236 CFM (TFA) (10.0 HP)

1236 CFM (TFA) (10.0 HP)

1236 CFM (TFA) (10.0 HP)

1236 CFM (TFA) (10.0 HP)

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm

34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm

9.5 mm dia &12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 4.c x 2.5 sqmm wire

Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R- 407 Green Refrigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 Degree Celsius. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electro technical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient temperature).

1.5 TR with 5 Star BEE Rating

1.5 TR with 5 Star BEE Rating

1.5 TR with 5 Star BEE Rating

1.5 TR with 5 Star BEE Rating

1.5 TR with 5 Star BEE Rating

1.5 TR with 5 Star BEE Rating

DUCTING,GRILLS,DIFFUSER AND ISNULATION

Description

Thickness 0.80 mm sheet

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.

Supply, installation, testing and commissioning of GI volume control sqm duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

80 mm dia

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supply, installation, testing and balancing of inlet air louvers with bird screen and volume damper for fresh air in powder coated extruded aluminium construction as per specifications and approved shop drawings.

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supply, fabrication, installation and testing the flexible connections constructed of fire resistance flexible double canvas sleeve as per the approved shop drawings.

Supply and fixing of Acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. above. Valves should have pressure rating of 25 Bar minimum.

Supply, Installation, Testing and commissioning of exhaust air fan suitable for Inline mounting comprising of forward curved centrifugal blower complete with induction motor, metal clad MCB, canvas connection all compete as required. Motor shall be suitable for single phase, 230 volts, 50Hz AC. supply as per specifications of following capacities: Noiselevel should not exceed 65dB(A)at 3 meter in room condition.

Providing and fixing in position the following PVC ( Min 3 mm thick) Heavy duty pipes cut to required lengths and all screwed joints with the necessary elbows, tees and reducers etc as per specifications.

100 mm dia pipes

STANDBY VRV SYSTEM

HVAC TOTAL

Power Cabling:

4Cx10 Sqmm Copper armoured

4Cx4 Sqmm Copper cable

3Cx2.5 Sqmm Copper cable

Supplying, installation, testing and commissioning of control cabling with insulated PVC sheathed wire/cable as per IS-7098 (Part-1) of following sizes including terminations on suitable cable trays / uPVC pipe with supports, as required including connections on both sides as per specifications and as required.

2 core x 1.5 sq. mm.

Cable Trays

Supplying and installing following size of performated pre-painted MS cable trays cross members with perforation not more than 17.5% joined with connectors, suspended from the ceilling with MS suspenders including nuts , bolts, bends , reducers etc. painted suspenders etc. as required.

300mm (W) x 50mm (D) x 1.6mm thickness

450mm (W) x 50mm (D) x 2.0mm thickness

Earthing:

8 SWG GI wire.

Supply of isolators for odu comprising of 32/63 amp MCB enclosed in weather proof MS casing

AUDIO- VIDEO & ALLIED WORKS

VIDEO CONFERENCING SYSTEM (Part 1)

Supply, Installation, testing and commissioning of USB all-in-one video conferencing bar according to the specifications provided below:

Parameter

Description

Camera Resolution

120° (H), 132° (Diagonal)

5x Digital Zoom

Smart Camera Features

AI-based speaker framing, people framing, group framing

Smart Camera Features

4 × Digital MEMS microphones

Pickup Range

Up to 4.5 m

AI noise reduction & acoustic fence

Speakers

Built-in stereo speakers

Connectivity

USB Type-C, USB Type-A, RJ-45 Ethernet (PoE++ support)

Wireless

Wi-Fi (802.11 a/b/g/n/ac), Bluetooth 5.0

Power Options

USB-C power / PoE++ support

Remote device management software support

DSP Features

Built-in intelligent audio & video processing

Compatibility

Compatible with major video conferencing platforms

Construction

Eco-friendly design with recycled materials

Mounting

Table, wall, and display mount compatible

Accessories

Remote control, power adapter, mounting kits (optional)

Included Items

USB cable, Ethernet cable, privacy cover, mounting clamp

Standard 1-year warranty

AUDIO SYSTEM Total (Part 2)

Supply, Installation, testing and commissioning of a digital UHF wireless handheld microphone systemaccording to the specifications provided below:

Digital wireless handheld microphone system

Dynamic capsule, cardioid pickup pattern

Frequency Band

Up to 2,240 frequencies

Up to 56 MHz

Up to 90 channels

20 Hz – 20 kHz

Up to 56 MHz

Up to 90 channels

Approx. 1.9 ms

Up to 100 m

Approx. 10 mW

Control & Setup

Mobile app-based setup and management

Rechargeable Li-ion / AA battery support

Up to 12 hours (Li-ion), ~8 hours (AA)

Receiver Type

Audio Output

Build

Lightweight handheld transmitter with mute switch

Features

Interference-free digital transmission, auto frequency management

Operating Conditions

Compatible with multiple microphone modules and accessories

Digital wireless lavalier microphone system

Pre-polarized condenser (lavalier)

Polar Pattern

Omnidirectional

20 Hz – 20 kHz (system), 50 Hz – 18 kHz (mic)

High dynamic range digital audio

Wireless with Bluetooth Low Energy control

App-based configuration and management

Transmitter Type

Bodypack transmitter (metal housing)

Microphone Sensitivity

Approx. 17 mV/Pa

Description

3.5 mm microphone input

Compatible with multiple lavalier and headset microphones

Speaker Type

Transducers

Frequency Range

Power Rating

Sensitivity

107 dB (Continuous) / 113 dB (Peak)

160° × 20° (nominal)

Q ≈ 15.9 / DI ≈ 12 dB

Euroblock connector with parallel output

Powder-coated aluminum

IP Rating

Quick hang pan/tilt wall mounting bracket with safety tether provision

DSP voicing support via compatible platform

Progressive taper topology for improved directivity and reduced side lobes

UL1480A compliant

Indoor/Outdoor installed sound, speech reinforcement, acoustically challenging spaces

2-way ceiling mount loudspeaker

6.5" polypropylene cone with rubber surround

0.86" silk dome tweeter (coaxially mounted)

110° conical

Compatible with multiple lavalier and headset microphones

Built-in 70/100V transformer with multiple taps and 8Ω bypass

8 Ω (bypass mode)

Enclosure / Baffle

Back Can

Grille

Low Frequency Design

DSP Compatibility

Installation

Safety Features

Certifications

Voice reinforcement, paging, background music, AV conferencing

Amplifier Type

Multi-channel Class-D power amplifier

2 channels

200 W per channel (4Ω / 8Ω / 70V / 100V)

Up to 400 W total power per channel pair, configurable

20 Hz – 20 kHz (±0.5 dB)

<0.01% typical

Input Sensitivity

Compatible with multiple lavalier and headset microphones

Maximum Input Level

>10 kΩ (balanced/unbalanced)

Enclosure / Baffle

Back Can

Grille

Low Frequency Design

High Pass Filter

Safety Features

Cooling

Voice reinforcement, paging, background music, AV conferencing

Amplifier Type

Forced air cooling with temperature-controlled fan

Protection

Connectors (Input)

20 Hz – 20 kHz (±0.5 dB)

Connectors (Output)

Remote I/O

200 W per channel (4Ω / 8Ω / 70V / 100V)

Up to 400 W total power per channel pair, configurable

Indicators

Power, signal, limit/mute/protect LEDs

<0.01% typical

Power Supply

Universal SMPS with PFC (100–240V AC, 50/60 Hz)

Compatible with multiple lavalier and headset microphones

High efficiency Class-D design

Auto standby with auto-ramp signal detection

UL, CE, RoHS, FCC compliant

Supply, Installation, testing and commissioning of Digital SmartMixer system according to the specifications provided below:

Digital Smart Mixer with DSP

Input Channels

Output Channels

USB Audio

Mixing Technology

Echo Cancellation

Noise Cancellation

Noise Cancellation

4-band EQ per channel

Equalization (Output)

Dynamics Processing

Feedback Suppression

Maximum Gain

Compatible with multiple lavalier and headset microphones

Euroblock connectors (Mic/Line, Stereo, Outputs)

Network / Control

RJ-45 Ethernet, IP-based remote control

Link Interface

Multiple RJ-45 ports for device linking/cascading

Cascading Capability

Up to 8 units

Front panel, web browser, and software application

Remote Control

Sampling / Conversion

AC 100–240V, 50/60 Hz

Low power consumption design

Conference rooms, meeting spaces, education, AV systems

VIDEO SYSTEM (Part 3)

Display Type

Screen Size

Resolution

4K Ultra HD (3840 × 2160)

Brightness

Compatible with multiple lavalier and headset microphones

Contrast Ratio

Viewing Angle

Aspect Ratio

10-bit (1.07 billion colors)

Anti-glare toughened glass (9H hardness)

Infrared touch

Up to 50 touch points

Response Time

Touch Tools

Operating System

Processor

Storage

Graphics

Built-in Software

Connectivity (Video Input)

Connectivity (Audio)

USB Ports

Network

Bluetooth 5.2

OPS slot for optional module

Built-in stereo speakers (20W × 2)

Integrated multi-mic array (long pickup range)

Compatible with multiple lavalier and headset microphones

Integrated AI high-resolution camera

VESA compatible

Meeting rooms, classrooms, collaboration environments

3840 × 2160 (4K Ultra HD)

1200:1 (Dynamic up to 300,000:1)

HDR Support

Panel Technology

Colour Gamut

Picture Processing

60 Hz with motion enhancement

24/7 continuous operation

DSP Compatibility

Orientation

Landscape / Portrait / Tilt compatible

Built-in speakers 20W (10W + 10W)

Internal Storage

Wireless Connectivity

Screen Mirroring

Ethernet (RJ-45)

IP Control, RS-232C, HDMI-CEC

HDMI ×4, USB ports, Composite AV input

Digital Audio Output

Pro Mode, HTML5 Signage Support, Multicast/IPTV

Convenience Features

Video Playback

Supports multiple video/audio/image formats via USB

Standby Power

Dynamic Backlight Control, Power Saving Mode

Compatible with multiple lavalier and headset microphones

Slim industrial design with side-mounted interfaces

VESA mount compatible

Suitable for corporate, retail, education and digital signage applications

Total (Part 3)

Supply, Installation, testing and commissioning of 17U Floor-mounted equipment rack according to the specifications provided below:

Rack Capacity

Heavy-duty CRCA steel construction with powder coating

Floor standing with provision for leveling feet/casters

Lockable front door with toughened glass/perforated metal

Lockable rear door with perforation for ventilation

Removable/lockable side panels

Suitable for standard AV/IT equipment load or better

Ventilation slots with provision for fan mounting

Top and bottom cable entry/exit with cable management provision

Adjustable mounting rails compatible with standard 19” equipment

Proper earthing provision

Finish

Suitable for AV/IT/Networking applications

Per Mtr.

Speaker Cable

Stranded ETP high-conductivity copper

Conductor Type

Insulation

Configuration

Parallel twin core

Electrical Performance

Flexibility

Convenience Features

Flexible stranded construction for easy installation

Suitable for PA systems, AV installations and speaker connectivity

Approved Make:

Beldon/ Impression/ Klotz

Compatible with multiple lavalier and headset microphones

Tender No. - FMD/HO/05/2026

Legrand/ Havells/ LT/ Hager

SECTION K - RODENT REPELLENT SYSTEM

Controller SITC of Microprocessor based Master Controller with Graphic LCD DISPLAY capable of operating in miimum 5 ultrasonic frequency band spectrums. The controller should also support upto 20 transducers @ minimum 500 sq. ft each. The system shall use UL/ CE approved. Necessary beacket reduired for mounting the controller shall also be prpvided

Maser/ Star Electronics

Transducer Supplying, Installation, Testing and Commissioning of transducer should cover a minimum area upto 300 sq. ft in all voids. No Looping permitted.

As prescribed by Maser/ Star Electronics

Proper earthing provision

MINERAL FIBRE BOARD FALSE CEILING - 600X600 MM Providing & Fixing of Mineral Fibre Acoustical Suspended Ceiling System with Bevelled Tegular Edge Tiles of 20mm thickness and 15mm bolt slot exposed grid.

Compatible with multiple lavalier and headset microphones

Supply, Installation, testing and commissioning of 2-core shielded microphone cable according to the specifications provided below:

ALUMINIUM FRAME WORK FOR PARTITIONS, PANELLING, ETC

Supply, Installation, testing and commissioning of Active SuperSpeed USB 3.2 Extension Cable of 10Mtr length according to the specifications provided below:

Active USB Extension Cable

Standard

Supply, Installation, testing and commissioning of 17U Floor-mounted equipment rack according to the specifications provided below:

USB 3.2 Gen 2

10 meter

Up to 10 Gbps

Signal Enhancement

Plug and play USB interface

Performance

Suitable for AV, IT and peripheral device connectivity

Conduit Type

PVC Conduit

High-quality rigid PVC

Strength

Fire Retardant

Resistant to moisture, chemicals and corrosion

Suitable for surface and concealed wiring

As per relevant IS standards

Total (Part 4)

WALLPAPERS Providing & applying of wall paper on the finished surfaces. The surfaces shall be thoroughly cleaned, line and level on all sides, dried and made free of all loose dirt, chalk, grease, fungus and algae, wax or flanking paint. Unwanted elements, hardware, clamps etc. shall be removed to make surface clean. The item also includes doing necessary touching work wherever required, by pop/putty for application. To shape actual areas on site will be considered for the measurement purpose (Samples of Wall Paper to be approved by the Client / Architect prior to ordering and installation). (Basic rate - Rs. 2000/- Sqm) - Make - Arte or equivalent

3M FILM Providing and fixing in position Sun control film of approved make and shade on the glass surface as per the directions of EIC/ Architect (Payment shall be made for the finished area of the film actually provided. No deduction shall be made for openings upto 0.1 Sq.m. area each and nothing shall be paid extra for making such openings.) Make: 3M Sun Control Window Film Prestige 70/ Llumar Stratos 70 or approved equivalent. (Basic rate - Rs. 700/- Sqm)

Basic rate - Rs. 450/- Sqm

Providing and installing in position Aluminium Frame Work of hollow sections of specified sizes given below for partitions, paneling, boxing, soffits etc. The aluminium frame work shall be of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with installing clips/ L-angle with vertical & horizontal members at not more than 600 mm center to center including necessary additional supports for installing of patch fittings of door, bracing, runner etc. so that lateral movement is arrested as per instructions of Architect/Engineer-in-charge. The first horizontal member shall be fixed at ground level and thereafter every 600mm. Frame work will be measured and paid as per actual measurement on site. The work shall be completed in all respects with necessary consumable as per detailed drawing, as specified and as directed by the Architect/Engineer-in-charge.

VENEER Providing & Fixing decorative high pressure Veneer sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive complete as per directions of Engineer- in- charge. - 4mm Thick (Basic rate Rs 1100/- Sqm)

QUARTZ Extra for providing quartz countertop instead of Granite. Basic Rate 8000/- Sqm

Size of tile 800x1600mm/1200x1800 (Basic rate - Rs. 760/- Sqm)

FLEXI TILE Providing and fixing Romanite Flexi Clay Tiles (Size 600x1200mm / 600x2400 mm) of approved shade and texture for interior or exterior wall cladding. Tiles shall be ultra-slim (2.5 mm to 3.0 mm thickness), made from natural modified clay, and capable of 360° bending without cracking. Installation includes surface preparation, application of specialized high-bond flexible PU adhesive, and grouting as per manufacturer guidelines. Complete as per directions of Engineer in charge/ Architect) Make - Flexi or equivalent. (Basic rate - Rs. 2500/- Sqm)

MINERAL FIBRE BOARD FALSE CEILING - 300X1200 MM Providing & Fixing of Mineral Fibre Acoustical Suspended Ceiling System with Bevelled Tegular Edge Tiles of 20mm thickness and 15mm face exposed grid. The tiles shall have sand texture visual with acoustical punchers, Humidity Resistance (RH) of 99%, NRC 0.7 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥84% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of class 0/1 as per BS 476 Part 6/7 and Class A as per ASTM E84 with 20mm bevelled Tegular edge and 8mm drop in module size of 300x 1200 mm. It shall be suitable for Green Building application, with Recycled content of 49%. The tile shall have certifications from GRIHA and GreenPro thereby confirming that it is an environment friendly product.

GLAZED DOOR - SINGLE LEAF Supply & Fixing of Glazed Door (Single Leaf of size 1000 x2400mm/ 1200 X2400 ) with Glass infill of toughened 10 mm glass with DORMA Alterra rebate door frame System (or equivalent) all around the door. Black matt finsih Aluminium STILE door to be formed out of 70x35mm Horizontal and Vertical Door Profile frame with clips & seals. Door Hardware -Flush hinges , Open Door Closer TS 70 Sleek body, with Dormakaba anti-microbial H type pull Handle 450mm with Narrow stile Lock package and dormakaba automatic Door Drop down seal.Suitable for Glass thickness of 10/12mm.The Profile shall be black inodised, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system . Installtion shoulb be done by authorised channel partner of company . All Profiles to be with 1.5 mm Gauge thickness Excluding 20 Micron of Anodizing. Max System Height - 2400mm , Finish - Black Matt finish/ Silver anodised. Glass Thickness : 10mm DORMA ALTERRA OR equivalent

Compatible with multiple lavalier and headset microphones

CUSTOMIZED FURNITURE

SEBI`s OFFICE SECTOR- 17, Chandigarh

BILL OF QUANTITY

WIRINNG FOR LIGHT POINT (LOOPED) Wiring for group controlled (looped) Light / Fan / Exhaust Fan / Call Bell point (without independent switch etc.) with 1.5 sq mm FRLS / HFFR, PVC insulated copper conductor single core cable in surface / recessed steel conduit, and earthing the point with 1.5 sq mm FRLS PVC insulated copper conductor single core cable etc. complete as required.

EARTHING

LED LIGHT

LED PANEL LIGHT 2 x 2 Ft (System Lumen Efficacy ≥105 <120Lm/ W) S/I/T/C of Panel Light. of following body material & construction as per IS : 10322 with driver as per requirement with Driver Efficiency >85%, Operating voltage AC 140 - 270 volts, Hz 50, Operating Temp range -5ºC to 40ºC, internal surge protectionof 2.5KV with short & open circuit protection,THD<10%, PF≥0.95, IP20, CRI ≥80, UGR (Unified Glayer Rating) ≤ 19, flicker free (Flicker should be below 5%) Life time (LED, Driver & ele.circuitry), of minim 50000 burning hours with 70% of initial lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000ºK / 4000ºK / 5700ºK / 6500ºK (As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating & fixture shall be confirming to relevant BIS standards. Manufacturers word mark / name engraved / embossing / screen printing on housing. Complete in all respect i/c external connection with 15sqmm FRLS PVC copper conductor single core cable & earthing etc. as required with minimum 5 yrs OEM Warranty, System efficacy ≥105 & <120Lm/W output.LM79 & LM80 Test report & all esting report for LED fixtures as per BIS shall be submitted. Shape size & CCT shall be as per approved by Er-in-Charge as per requirement. (Thermal management heat sink of aluminium housing such that LED junction temperature shall not rise above 90ºC) Powder coated CRCA Sheet aluminium Body (Thickness ≥0.50mm)

MV CABLE JOINTING & END TERMINATION

ON-LINE UPS - INPUT SUPPLY : THREE PHASE, OUTPUT SUPPLY : THREE PHASE + NEUTRAL Supply, Installation,Testing and commissioning of following capacity at full load (Unity Power Factor) Operating temperature 0 to 40ºC, Relative humidity 0 - 95%, ON LINE DOUBLE CONVERSION True Sine Wave, UNINTERRUPTED HOT Swapable (Allow for the replacement or addition of Battery Modules without shutting down the entire system) Modular Power Supply (UPS) system with N + 1 modules (N denotes total number of modules required for rated capacity), The UPS shall include a Rectifier, Inverter, Battery Bank, suitable for 30 minues back up (Battery VAH capacity shall not be less than 1600VAH per KVA of UPS rating per hourback up time) on full load (Battery shall be VRLA, SMF in ABS Container) an Static Bypass Switch along with provision for manual bypass, suitable isolation transformer Copper Wound for additional protection against neutral faults etc. The UPS System shall be Microprocessor Based Digital Control, using Insulated Gate Bipolar Transistor (IGBT)`s both for the Rectfier & Inverter with PWM (Pulse Width Modulation) Technology. The quality of design, manufacturing and inspection process should confirm to the relevant Inter-national Standards such as IEC / EN / VDE. The operating efficiency of the UPS system shall be ≥96% while operating on Battery Mode and delivery quality power at the 100% non-linear Loads. Current total Harmonic Distortion (ITHD) / total demand distortion (TDD) on the input grid shall be < 5% at 50% load. [The rquired LC (Inductor (L) and Capacitor (C) Filter shall be included in UPS Cost), Extreme power factor kit to be included to limit the input PF to 099, and output power factor shall be Unity. (i.e. kw rating of the UPS shall be KVA rating x 1) however UPS shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC Three Phase 400V ± 20%, 50Hz ± 5% and delivering output AC Supply Three 415 Volts, 50Hz ± 0.2Hz, Overload capacity of 120% for 10 minutesand, Sine wave output, No at 1 meter distance condensing, noise level less than 60db Protection for Under Voltage, Over Voltage, abnormal output Voltage, Battery Over Charging, Output Current, Short Circuit, Battery Deep Discharge, 10KV Surge, Display for Watt / VA, Amp and Voltage Power Parameters etc. UPS shall comply with low Voltage electromagnetic compatibility (EMC) achieved as per EN 6204, EN 6204 Part - 1 and Part 2, it shall be a Voltage and Frequency Independent (VFI) UPS. Communication RS 232 / RS 485 / SNMP Port open Protocol for BMS integration, all hardware and software for IOT Communication as per approved by Engineer-in-Charge. Required Battey Racks, and interconnecting copper conductor cable of suitable size and connectors and all required accessories are inclusive in the cost. This system must provide a means for logging and alarming of all monitored points plus email notification. Forced air cooling with integral inbuilt fans with redundancy (If one fan fail UPS shall be able to handle at least 80% of the load. The system shallbe in compliance IEC 62040 - 1, 2 & 3, IS : 16242 and CPWD Specifications. Display panel (minimum) [inuilt 5" or more LC Display / LED] to display :-

FIRE DETECTION AND ALARM SYSTEM

VOICE COMMAND KEYPAD Supplying, Installation,Testing & Commissionng of Voice Command Keypad 6 Zone with Microphone assembly complete as required

KOEL & SUDHIR/ CUMMINS

CISCO, ARUBA

DLINK, LEGRAND

LEGRAND , DLINK, PANDUIT

Compatible with multiple lavalier and headset microphones

CCTV CAMERA SYSTEM

BOSCH , HONEYWELL, PANASONIC

Assa Abloy, Dorma Godrej and Boyce

Dorma, Mantra Softech, Essl security, Honeywell

Accrete Automation

NS ITEMS

TMD Based MCCB Make :-All MCCB`s with TMD Based and having O/L, S/C Protection - LK Model D-Sine, Schneider Model CVS, Siemens Model 3VA, ABB Model Tmax. Legrand Model DPX3 with S2 (Lsi) Ics=Icu=100%

LED PANEL LIGHT FIXTURE HAVING LUMEN EFFICACY ≥105 <120Lm/ W) S/I/T/C of LED Light fixture of following body material & construction as per IS : 10322 with driver as per requirement with Driver Efficiency >85%, Operating voltage AC 140 - 270 volts, Hz 50, Operating Temp range -5ºC to 40ºC, internal surge protectionof 2.5KV with short & open circuit protection,THD<10%, PF≥0.95, IP20, CRI ≥80, UGR (Unified Glayer Rating) ≤ 19, flicker free (Flicker should be below 5%) Life time (LED, Driver & ele.circuitry), of minim 50000 burning hours with 70% of initial lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000ºK / 4000ºK / 5700ºK / 6500ºK (As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating & fixture shall be confirming to relevant BIS standards. Manufacturers word mark / name engraved / embossing / screen printing on housing. Complete in all respect i/c external connection with 15sqmm FRLS PVC copper conductor single core cable & earthing etc. as required with minimum 5 yrs OEM Warranty, System efficacy ≥105 & <120Lm/W output.LM79 & LM80 Test report & all esting report for LED fixtures as per BIS shall be submitted. Shape size & CCT shall be as per approved by Er-in-Charge as per requirement. (Thermal management heat sink of aluminium housing such that LED junction temperature shall not rise above 90ºC) Powder coated CRCA Sheet aluminium Body (Thickness ≥0.50mm)

S/I/T/C of 5 Watt / Meter LED Strip Light Fixture of 5 Mtr Roll, IP 20, CCT Warm White with Driver including jointing connector etc. complete in all respect as required (Ref Model - Wipro LS-06-05-12-30-50g1 or Equal) Make: PHILIPS, WIPRO, LT

Supply, Installation, testing and commissioning of an 65-inch 4K Ultra HD interactive display according to the specifications provided below:

Compatible with multiple lavalier and headset microphones

CCTV CAMERA SYSTEM

BOSCH , HONEYWELL, PANASONIC

Assa Abloy, Dorma Godrej and Boyce

Dorma, Mantra Softech, Essl security, Honeywell

Accrete Automation

NS ITEMS

TMD Based MCCB Make :-All MCCB`s with TMD Based and having O/L, S/C Protection - LK Model D-Sine, Schneider Model CVS, Siemens Model 3VA, ABB Model Tmax. Legrand Model DPX3 with S2 (Lsi) Ics=Icu=100%

LED PANEL LIGHT FIXTURE HAVING LUMEN EFFICACY ≥105 <120Lm/ W) S/I/T/C of LED Light fixture of following body material & construction as per IS : 10322 with driver as per requirement with Driver Efficiency >85%, Operating voltage AC 140 - 270 volts, Hz 50, Operating Temp range -5ºC to 40ºC, internal surge protectionof 2.5KV with short & open circuit protection,THD<10%, PF≥0.95, IP20, CRI ≥80, UGR (Unified Glayer Rating) ≤ 19, flicker free (Flicker should be below 5%) Life time (LED, Driver & ele.circuitry), of minim 50000 burning hours with 70% of initial lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000ºK / 4000ºK / 5700ºK / 6500ºK (As per ANSI Bin), SDCM (Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating & fixture shall be confirming to relevant BIS standards. Manufacturers word mark / name engraved / embossing / screen printing on housing. Complete in all respect i/c external connection with 15sqmm FRLS PVC copper conductor single core cable & earthing etc. as required with minimum 5 yrs OEM Warranty, System efficacy ≥105 & <120Lm/W output.LM79 & LM80 Test report & all esting report for LED fixtures as per BIS shall be submitted. Shape size & CCT shall be as per approved by Er-in-Charge as per requirement. (Thermal management heat sink of aluminium housing such that LED junction temperature shall not rise above 90ºC) Powder coated CRCA Sheet aluminium Body (Thickness ≥0.50mm)

S/I/T/C of 5 Watt / Meter LED Strip Light Fixture of 5 Mtr Roll, IP 20, CCT Warm White with Driver including jointing connector etc. complete in all respect as required (Ref Model - Wipro LS-06-05-12-30-50g1 or Equal) Make: PHILIPS, WIPRO, LT

Supply, Installation, testing and commissioning of an 65-inch 4K Ultra HD interactive display according to the specifications provided below:

Compatible with multiple lavalier and headset microphones

Infrared (IR)

Touch Response Time

Audio

Built-in Speakers (15W × 2)

Android 14 (EDLA Certified)

Wi-Fi + Bluetooth

OPS Slot

Supported

Compatible with multiple lavalier and headset microphones

Wall Mount (VESA 600×400)

Power Cable, Remote, HDMI Cable, USB Cable, 2 × Touch Pens, Manual

Optional